Operating instructions

ManualsBrandsMoog ManualsSecurity CamerasACH13HB8N SERIES

www.moogvideolarm.com

A C H 1 3 H B 8 N

Aluminum Outdoor Environmental Camera Housings

Installation and Operation Instructions for the following models:

ACH13HB8N Outdoor environmental housing for PoE plug enabled IP xed cameras,

wall/pole mount, dynamic (intelligent) power allocation heater/blower

system, 30W midspan (100-240Vac input 50/60Hz)

ACH13HB8NE Outdoor environmental housing for PoE plug enabled IP xed cameras,

wall/pole mount, dynamic (intelligent) power allocation heater/blower

system

Before attempting to connect or operate this product, please read these instructions completely.

81-IN5455

06-26-2012

Summary of content (10 pages)

PAGE 2
IMPORTANT SAFEGUARDS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with damp cloth. 7 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 8 9 SAFETY PRECAUTIONS Cable Runs- All cable runs must be within permissible distance.
PAGE 3
Limited Warranty for Moog Videolarm Products Moog Videolarm warrants these products to be free from defects in material or workmanship as follows: PRODUCT CATEGORY PARTS \ LABOR All Enclosures and Electronics* Five Poles/PolEvators™/CamEvator Three (3) Years Warrior Series™/Q-View™/IR Illuminators Five (5) Years SView Series™ Five (5) Years **6 months if used in auto scan/tour operation Controllers Five (5) Years Power Supplies Five (5) Years EcoKit Three (3) Years Accessory Brackets F
PAGE 4
! English Español Français Deutsch Portuguese Italiano Electrical Specifications Midspan ACH13HB8N Unpacking the Product ACH13HB8N Input Power: 100 to 240VAC Power: .8A Frequency: 50 to 60 HZ Output Camera: POE (55VDC) Heater: 55VDC (max. 20W) Energía de entrada: 100 a 240VAC: Energía: .8A Frecuencia: 50 a 60 hertzios Salida: Cámara: POE (55VDC) Calentador: 55VDC (máximo 20W) * Puissance d'entrée : 100 à 240VAC Puissance: .
PAGE 5
1 2 Attach the bracket to the wall and secure appropriately. Connect housing to wall bracket. • Una el soporte a la pared y asegúrelo • Conecte la cubierta con el soporte de pared. apropiadamente. • Attachez la parenthèse au mur et la fixez convenablement. • Bringen Sie den Haltewinkel zur Wand an und sichern Sie passend. • Una o suporte à parede e fixe-o apropriadamente. • Fissi la staffa alla parete e fissi giustamente. 3 • Reliez le logement à la parenthèse de mur.
PAGE 6
5 Sled Screw Camera Sled Place camera on sled and align mounting holes on each. Adjust camera parallel to sled and tighten the bolt on the bottom. • • • • • Coloque la cámara fotográfica en el trineo y alinee los agujeros de montaje en cada uno. Ajuste la cámara fotográfica paralela al trineo y apriete el perno en el fondo. Placez l'appareil-photo sur le traîneau et alignez les trous de support sur chacun. Ajustez l'appareil-photo parallèle au traîneau et serrez le boulon sur le fond.
PAGE 7
TEST Button HEAT 8 Press the Calibration button for one second. Both the Test and Heat LED will turn ON. Once the unit has been successfully calibrated, the Test and Heat LED will turn OFF. Once this is complete the Heat LED will turn ON only if the heater is ON. • Pulse el botón de calibración durante un segundo. Tanto la prueba y el calor se encenderá. Una vez que la unidad ha sido calibrado correctamente, la prueba y el calor del LED se apagará.
PAGE 8
10 11 Close the top cover and tighten to the base with the hex screws. If desired, use security screws in place of hex screws. • Cierre la cubierta superior y apriete a la base con los tornillos de la tuerca hexagonal. • Si está deseado, utilice los tornillos de la seguridad en lugar de los tornillos de la tuerca hexagonal. • Fermez la couverture supérieure et serrez à la base avec les vis de sortilège. • Si désiré, utilisez les vis de sécurité au lieu des vis de sortilège.
PAGE 9
Replacement Parts List ACH13HB8N 12 # Part Number Description 1 RPACH010 ACH13 Front Endcap Assembly 2 RPACH020 ACH13 Lid Screws 3 RPHACH8N Heater for POE housing 4 RPACH050 12V Heater & Thermostat Kit For ACH13 5 RPACH060 ACH13 Top Extrusion 6 7 RPACH070 RPBACH8N ACH13 Bottom Extrusion Blower for POE housing 8 RPPCBPOE 9 RPACH110 PC board for POE housing ACH13 Rear Endcap Assembly 10 RPACHPK Packet Assembly 11 WM800 Medium Duty Wall Mount Bracket For ACH13 12 ACH130 ACH1
PAGE 10
Product Registration/Warranty Thank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highest quality products available and superior customer service. Should a problem arise, rest assured that Moog Videolarm stands behind its products by offering impressive 3 Year and 5 Year warranties, depending on the product purchased. See full warranty details at www.moogvideolarm.