Operating instructions

ManualsBrandsMoog ManualsHome building and DecorIPRS01

Moog Inc.

Sensor and Surveillance Systems

3650 Woodhead Drive Northbrook, IL. USA 60062

+1.847.498.0700 Fax: +1.847.498.1258 www.moogS3.com

IP Reset

Automatic IP Camera Restart Accessory

IP Reset..................... IP Reset- provides a systematic solution for resetting IP cameras or wireless systems, lock-ups caused by network issues,

wiring problems and power fluctuations by monitoring the output of an IP camera’s digital signal

Installation Steps:

➊ Check the package contents

➋ Select Operation Mode

➌ Install Hardware

a. Timed Reset Mode

b. Intelligent Reset Mode

➍ Read LED Operation instructions

➎ Install Software- See IP Reset Manager Software (on CD-ROM)

Installation and Operation Instructions

Before attempting to connect or operate this product, please

read these instructions completely.

81-IN5416 111513

Summary of content (24 pages)

PAGE 1
Installation and Operation Instructions Before attempting to connect or operate this product, please read these instructions completely. IP Reset Automatic IP Camera Restart Accessory IP Reset.....................
PAGE 2
IMPORTANT SAFEGUARDS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with damp cloth. 7 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 8 9 SAFETY PRECAUTIONS Cable Runs- All cable runs must be within permissible distance.
PAGE 3
Product Warranty Registration Register Your Products Online www.moogS3.com/technical-support/product-registration Moog values your patronage. We are solely committed to providing you with the highest quality products and superior customer service. With 3-Year and 5-Year warranties (depending on the product purchased) we stand behind every product we sell. See full warranty details at www.moogS3.
PAGE 4
Limited Warranty for Moog Products Moog - Decatur Operations, subsequently referred to as “Manufacturer,” warrants these products to be free from defects in material or workmanship as follows: PRODUCT CATEGORY PARTS \ LABOR All Enclosures and Electronics Five (5) Years Accessory Brackets Five (5) Years Controllers Three (3) Years Power Supplies / IR Illuminators Three (3) Years Poles / PolEvators / CamEvator Three (3) Years Warrior Series / Q-View Three (3) Years ™ ™ ™ Three (3) Years 6 mo
PAGE 5
! Product Specifications Content of Box IPRS01 IPRS01 Power Requirements Input Voltage: 5 to 24 Volts AC/DC English Operating Current: 12ma Device Power Requirements Maximum Operating Current: 2 Amps CD Maximum Switching Current: 5 Amps I/O Detect Input Input Voltage: -25VDC to +25VDC Input Drive Current: 3ma @ 12V Typ. Threshold: +1.9 VDC I/O Cable Length: 6" or 15.
PAGE 6
! CAUTION: IP Reset is not weatherproof. When connected to an outdoor camera Please make sure it is protected by a camera enclosure. Do not open IP Reset or all warranties will be voided. ! WARNING: To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the unit. Refer servicing to qualified personnel only. Operating Modes The IP Reset operates in one of two modes, Intelligent Reset Mode and Timed Reset Mode.
PAGE 7
Output Relay Configuration and Connections Output Relay Configuration The relay output configurations vary based on the manufactures design. Because of these variations, the IP Reset I/O Detect input needs to operate in one of three ways. Refer to your camera user manual for more information regarding the output relay configuration of your camera. Dry Contact The first and most common method requires the IP Reset to supply current to the dry contacts of a relay. This configuration is shown in Figure 5.
PAGE 8
Hardware Installation The hardware installation depends upon the desired operating mode - Timed Reset Mode or Intelligent Reset Mode. Timed Reset Mode Installation 1. Do not connect I/O Detect cable. Instead, twist wires together with provided wire nut. 2. Connect the power output pin from the IP Reset to the Power input on your device 3. Connect the power from the transformer to the power input in the IP Reset. 4. No IP Reset Manager Software installation is necessary.
PAGE 9
Hardware Installation (cont.
PAGE 10
Software Installation (For a windows based PC) If there is a preexisting version of the IP Reset Manager Software on your computer go to “Add/Remove Programs “from the MS Windows Control Panel and remove it before beginning a new software installation. To remove a preexisting IP Reset Manager Installation, go to the Windows “Control Panel” and click on the “Add or Remove Programs” software icon.
PAGE 11
Software Installation (For a windows based PC continued) In response to the confirmation box “Add or Remove Programs” message. Click “Yes”. A window may show up as follows: Let this window run to completion. Following the above window if you are removing the application from a computer with the Windows Vista operating system, a window (not shown) may appear with the title “User Account Control”.
PAGE 12
IP Reset Manager Software Installation Guide After you have fully removed any preexisting installations of IP Reset Manager (see section “Removing IP Reset Software” from your system), insert the CDROM that came with your IP Reset device into the hard drive of the networked computer that will run the IP Reset Manager Software (computer must be on the same network with the video cameras) If the installation file doesn’t launch automatically, Double click on “setup.
PAGE 13
IP Reset Manager Software Installation Guide Continued A Window pops up that says “Select Installation Folder”, if the radio button “just me” is selected, (shown below) than change it to the radio button “Everyone”, as shown below A window will appear that says, “Confirm Installation”, Click “Next >” to confirm the installation!
PAGE 14
IP Reset Manager Software Installation Guide Continued Following the above window if you are installing the IP Reset application from a computer with the Windows Vista operating system, a window (not shown) may appear with the title “User Account Control”. It will say “An Unidentified Program Wants to Access Your Computer”, if this window appears you should click the “Allow” option.
PAGE 15
Older machines may require downloading Microsoft Dot Net If you are on an older windows machine that does not have a current version of Microsoft’s Dot Net libraries, you may get a message from Windows requiring you to download the latest version of Microsoft .Net. At this point you will have log on to Microsoft at: http://msdn.microsoft.com/en-us/netframework/default.aspx And download the latest version of Microsoft’s .Net libraries. After doing this double click on the downloaded files to install .Net.
PAGE 16
You are now ready to run the IP Reset Configuration Software. For usage information refer to application users document “IP ResetSoftwareUsersGuide.pdf” which is enclosed as a PDF with the CD-ROM. After successful installation the user’s guide and operations guide can be found on your computer in the following directory: “C:\Program Files\Moog\IP Reset\IP Reset_Software_User_s Guide.pdf” is the application manual used to configure IP Reset devices from the computer.
PAGE 17
PAGE 18
PAGE 19
PAGE 20
PAGE 21
PAGE 22
PAGE 23
PAGE 24