Operating instructions

ManualsBrandsMoog ManualsSecurity CamerasP1800

Moog Inc.

Sensor and Surveillance Systems

3650 Woodhead Drive Northbrook, IL. USA 60062

+1.847.498.0700 Fax: +1.847.498.1258 www.moogS3.com

P1800 and P1800TB

18' Video Surveillance Rated Fixed Steel Pole Lowering Device

P1800....................... Moog designed a solid construction 16’ steel pole with 2’ transformer base NEMA enclosure. Base includes terminal strip, 115Vac to

24Vac transformer and surge protection

P1800TB....................P1800 without NEMA Box or electronics

Installation and Operation Instructions

Before attempting to connect or operate this product, please

read these instructions completely.

81-IN5288 111813

Summary of content (10 pages)

PAGE 1
Installation and Operation Instructions Before attempting to connect or operate this product, please read these instructions completely. P1800 and P1800TB 18' Video Surveillance Rated Fixed Steel Pole Lowering Device P1800....................... Moog designed a solid construction 16’ steel pole with 2’ transformer base NEMA enclosure. Base includes terminal strip, 115Vac to 24Vac transformer and surge protection P1800TB....................P1800 without NEMA Box or electronics Moog Inc.
PAGE 2
IMPORTANT SAFEGUARDS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with damp cloth. 7 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 8 9 SAFETY PRECAUTIONS Cable Runs- All cable runs must be within permissible distance.
PAGE 3
Product Warranty Registration Register Your Products Online www.moogS3.com/technical-support/product-registration Moog values your patronage. We are solely committed to providing you with the highest quality products and superior customer service. With 3-Year and 5-Year warranties (depending on the product purchased) we stand behind every product we sell. See full warranty details at www.moogS3.
PAGE 4
Limited Warranty for Moog Products Moog - Decatur Operations, subsequently referred to as “Manufacturer,” warrants these products to be free from defects in material or workmanship as follows: PRODUCT CATEGORY PARTS \ LABOR All Enclosures and Electronics Five (5) Years Accessory Brackets Five (5) Years Controllers Three (3) Years Power Supplies / IR Illuminators Three (3) Years Poles / PolEvators™ / CamEvator Three (3) Years Warrior Series™ / Q-View™ Three (3) Years SView Series Three (3) Ye
PAGE 5
2. To help reinforce the concrete foundation, place (12) 1/2" diameter x 32" long Reinforcement Bars ("rebar") as shown in Figure 2. Use suitable preparation methods to place the rebar. STANDARD INSTALLATION PROCEDURE INCLUDES MODELS: P1800 ! Please read these instructions carefully before proceeding, and heed all cautions. 6" 24" 6" ! NOTE: If you'll be using the optional PV4 anchor jig, see the attached instructions for assembly of the jig.
PAGE 6
3. FOR ANCHOR BOLT INSTALLATIONS: Pour concrete per manufacturer's directions, making sure that the wiring conduit is in the center of the pad. See Figure 3 for dimensions of the bolt pattern and suspend appropriate bolts in the concrete around the wiring conduit. Leave 2" to 3" of the Bolts protruding above the pad. If you are using leveling nuts, leave 4" to 6" protruding. 4 x O 1" 4X O 1.000 BasedBASED on ONanA 11.00" 11"B.C.B.C. 7.778 7.778" Figure 5 2.
PAGE 7
5. Place the pole on the pad with the holes on the Transformer Base aligned with the bolts of the anchor bolts or anchor jig and slowly lift the pole into the upright position (Figure 7). CAUTION: Pull all slack in the wiring as you lift the pole into position to keep from pinching and possible damage. Figure 7 5. Ensure that the pole is vertical on all sides. Use a bubble level or plumb bob to check. 6. Secure the pole to the pad with fasteners (Figure 8).
PAGE 8
Wiring Inside the NEMA Box ! NOTE: This unit MUST be grounded. If you do not have ground on the incoming power, you MUST run appropriate ground out from the NEMA box • Run 115 VAC power into the NEMA box through the conduit opening closest to the power transformer. Make the appropriate connections. • Run video and control into the NEMA box through the conduit opening closest to the surge protector. Connect video output to the surge protector.
PAGE 9
NEMA Box Wiring Diagram Video output 1 2 3 4 AC 5 Neutral 6 Ground 115 VAC Incoming Power 24 VAC power User Wiring Connections 1 RED RX Control Data 2 3 4 ORANGE YELLOW GREEN RX Control Data TX Control Data TX Control Data 5 6 BLUE GRAY Alarm Alarm pre-connected
PAGE 10
Anchor Jig Assembly 4. Before using the Anchor Jig verify that the center to center dimensions between the bolts are even (Figure 4). If not, adjust accordingly. Firmly tighten all Hex Nuts. Anchor Jig Kit Parts List Single Straps (4) 3/4" Flat Washers (4) Cross Strap (1) 7 3/4" - 10 Hex Nut (20) Lock Washers (4) ! / " 25 32 3/4" - 10 Bolts (4) 11" diameter CAUTION: TO PREVENT CORROSION; NEVER MIX GALVANIZED HARDWARE WITH STAINLESS STEEL HARDWARE! 1.