user’s guide A39TL & A30FL-S MOBILITY SCOOTERS
hello CONGRADULATIONS ON THE PURCHASE OF YOUR NEW SCOOTER. WE ARE QUITE CONFIDENT THAT YOU ARE GOING TO GET ALONG. We designed this scooter with one main objective - to provide mobility, independance and freedom, all coupled with ease of use and a touch of style. This user guide is intended to help you become familiar with the ins and outs of your scooter, so that you can ensure high performance and long life for your scooter.
TABLE OF CONTENTS ANATOMY OF A SCOOTER BATTERY BATTERY F.A.Q. OPERATION ELECTROMAGNETIC INTERFERENCE (EMI) SAFETY ASSEMBLY AND DISSASSEMBLY MAINTENANCE SPECIFICATIONS WARRANTY BUYER’S REGISTRATION FORM The manufacturer reserves the rights of final interpretation on the manual. For any printing mistakes or new improvements, the manufacturer will update in the new editions.
ANATOMY OF A SCOOTER TILLER CONSOLE The tiller console houses all controls needed to drive your scooter, including the key switch, throttle control levers, speed adjustment dial, and the battery status meter. (See figure 1). KEY SWITCH - Fully insert the key into the key switch to turn on your scooter. - Remove the key from the key switch to turn off your scooter. THROTTLE CONTROL LEVERS The throttle levers allow you to control the machine moving forward and backward.
BATTERY STATUS METER When the key is fully inserted the key switch, this meter indicates approximate battery strength. For further information on the battery condition meter, see page 5 on batteries and charging. REAR SECTION The manual freewheel lever, ant-tip wheels, and motor/transaxle assembly are located on the rear section of your scooter. (See figure 2). MANUAL FREEWHEEL LEVER Whenever you need or want to push your scooter for short distance, you can put it in freewheel mode.
BATTERY Your scooter is equipped with two sealed, maintenance free 17 AH batteries. - Charge the batteries prior to using your scooter for the first time. - Keep the batteries fully charged to keep your scooter running smoothly. READING YOUR BATTERY VOLUME The battery volume meter on the tiller console uses a color code to indicate the condition of your batteries. Green indicates fully charged batteries, yellow a draining charge, and red indicates that an immediate recharging is necessary.
BATTERY F.A.Q. How does the charger work? When your scooter’s battery voltage is low, the charger works harder, sending more electrical current to the battery to bring up their charge. When the voltage approaches full level, the charger is at nearly zero amperage. Therefore, when the charger is plugged in, it maintains the charging on your scooter’s batteries, but will not overcharge them. But we do not recommend that you charge your scooter for more than 24 consecutive hours.
OPERATION ELECTROMAGNETIC INTERFERENCE BEFORE GETTING ONTO YOUR SCOOTER - Have you fully charged the batteries? See page 5, “Batteries and charging.” - Ensure that the manual freewheel lever in the open (power driven) position? Never leave the manual freewheel lever in the close position unless you are manually pushing your scooter. - Ensure that the tiller lock knob is in the locked position? See page 9, “Disassembly and assembly.
SAFETY Your scooter can negotiate grass, gravel, dirt, and sand surfaces, as well as hard paved or carpeted surfaces. However, extra caution should be taken when operating your unit on uneven surfaces other than flat surfaces. You should also be aware of the potential effect of electromagnetic interference (EMI) on scooter operation. More information about EMI can be found on the previous page or on our website at www.moosemobilityscooter.
ASSEMBLY AND DISSASSEMBLY The scooter has been designed to assembled and disassembled quickly and easily without the use of tools. Should you need excessive force when you assemble or disassemble your unit, you are probably doing something wrong and should refer to the User’s Guide, then try again.
DISSASSEMBLY To dismantle the scooter just reverse the steps for assembly. *You must power off your scooter before dissassembly. (1) Turn off the power and take out the power key from switch lock. (2) Loosen and remove the seat from the seat post. (3) Disconnect the main battery cable from the controller. (4) Unplug all battery connections. (5) Remove the batteries box from front chassis. (6) Toggle latch release -Press the latch button and then pull the toggle latch forward.
MAINTENANCE Your scooter requires a proper care and maintenance. If you do not feel confident in your ability to perform the maintenance listed below, you may schedule inspection and maintenance with your authorized dealer. The following areas require periodic inspection and/or care and maintenance. TIRES Regularly inspect your scooter’s tires for signs of wear. WIRING Regularly check the wiring insulation for wear or damage.
SPECIFICATIONS Model Numbers 3-wheel: J30TL 4-wheel: J30FL Overall Length 3-wheel: 42 in. (1067mm) 4-wheel: 43 in. (1092mm) Overall Height 3-wheel: 37 in. (940mm) 4-wheel: 35 in. (890mm) Overall Width 19 in (483mm) Weight Without Battery Pack 3-wheel: 67 lbs 4-wheel: 76 lbs Turning Radius 3-wheel: 33 in (838mm) 4-wheel: 31 in (788mm) Forward Speed (maximum) 6.4km/h Backward Speed (maximum) 3.2km/h Range Per Charge* Up to 18miles Ground Clearance 1.
WARRANTY The manufacturer guarantees that the products manufactured by them to be free from defects in materials and workmanship for a period of one year from the date of purchase. If, within such warrant period, any such products shall be proven to be defective, such product shall be repaired or replaced, at the manufacturer’s option. To guarantee your benefits and the excellent after-sale service provided by the manufacturer, please read the following carefully.
BUYER’S REGISTRATION FORM Mobility Scooters NOTICE: SELLING DEALER SHOULD COMPLETE THIS FORM AT THE TIME OF SALE TO REGISTER WARRANTY.
MOBILITY SCOOTER CO. Est.
