user’s guide J50TL, J50FL & J50FL-S MOBILITY SCOOTERS
hello CONGRADULATIONS ON THE PURCHASE OF YOUR NEW SCOOTER. WE ARE QUITE CONFIDENT THAT YOU ARE GOING TO GET ALONG. We designed this scooter with one main objective - to provide mobility, independance and freedom, all coupled with ease of use and a touch of style. This user guide is intended to help you become familiar with the ins and outs of your scooter, so that you can ensure high performance and long life for your scooter.
TABLE OF CONTENTS ANATOMY OF A SCOOTER BATTERY BATTERY F.A.Q. OPERATION ELECTROMAGNETIC INTERFERENCE (EMI) SAFETY ASSEMBLY AND DISSASSEMBLY MAINTENANCE SPECIFICATIONS WARRANTY BUYER’S REGISTRATION FORM The manufacturer reserves the rights of final interpretation on the manual. For any printing mistakes or new improvements, the manufacturer will update in the new editions.
FEATURES Modular construction - disassembles in one minute without use of tools Adjustable seat height Swing away armrests 360 degrees swivel seat Adjustable Forward/Reverse Seat Adjustable tiller Dynamic regenerative braking coupled with fail-safe elec tro-mechanical disk brake Rear wheel direct drive with differential Fully solid state controller External Battery Charger 24-volt permanent magnet heavy duty DC motor 3 ON/OFF switch lock Horn Head light Turning lights R
4
BATTERY To ensure the best performance and maximum battery life, we recommend frequent battery charging. Your scooter comes with an external battery charger for your ease and convenience. The console battery display makes charging simple and easy. Follow these steps for battery charging. READING YOUR BATTERY VOLUME The console battery level display has two green lights (100% and 50%), one yellow light (25%, you’d better charge now), and one red light (almost empty, you must charge them right now).
BATTERY F.A.Q. How does the charger work? When your scooter’s battery voltage is low, the charger works harder, sending more electrical current to the battery to bring up their charge. When the voltage approaches full level, the charger is at nearly zero amperage. Therefore, when the charger is plugged in, it maintains the charging on your scooter’s batteries, but will not overcharge them. But we do not recommend that you charge your scooter for more than 24 consecutive hours.
OPERATION ELECTROMAGNETIC INTERFERENCE BEFORE GETTING ONTO YOUR SCOOTER - Have you fully charged the batteries? (See page 5, “Batteries and charging.”) - Ensure that the clutch realease lever in the open (power driven) position. Never leave the clutch realease lever in the close position unless you are manually pushing your scooter. - Ensure that the tiller lock knob is in the locked position. (See page 9, “Disassembly and assembly.
SAFETY Your scooter can negotiate grass, gravel, dirt, and sand surfaces, as well as hard paved or carpeted surfaces. However, extra caution should be taken when operating your unit on uneven surfaces other than flat surfaces. You should also be aware of the potential effect of electromagnetic interference (EMI) on scooter operation. More information about EMI can be found on the previous page or on our website at www.moosemobilityscooter.
ASSEMBLY AND DISSASSEMBLY The scooter has been designed to assembled and disassembled quickly and easily without the use of tools. Excessive force should not be required. If you encounter a problem, please refer to the User’s Guide, then try again. If the problem persists, don’t hesitate to call your authorized dealer for assistance.
DISSASSEMBLY To dismantle the scooter just reverse the steps for assembly. *You must power off your scooter before dissassembly. (1) Turn off the power and take out the power key from switch lock. (2) Loosen and Remove the seat from the seat post. (3) Disconnect the turning lights cable and remove the rear fairing. (4) Disconnect the main battery cable from the controller. (5) Unplug all battery connections. (6) Remove the batteries from floor pan. (7) Disconnect the front chassis cable from the controller.
MAINTENANCE Your scooter requires proper care and maintenance. If you do not feel confident in your ability to perform the maintenance listed below, you may schedule inspection and maintenance with your authorized dealer. The following areas require periodic inspection and/or care and maintenance. TIRES Regularly inspect your scooter’s tires for signs of wear. WIRING Regularly check the wiring insulation for wear or damage.
SPECIFICATIONS Model Numbers J50TL - 3 wheel J50FL - 4 wheel J50FL-S - 4 wheel Standard Seating Type: Foldable vinyl polyurethane covered foam Dimensions: Width: 16.5 in (420mm) Depth: (usable) 16 in (406mm) Height: 13.5 in (343mm) Material: black vinyl Overall Length 1200 mm Overall Width 650 mm Weight Without Battery Pack 3-wheel: 57.2 kg 4-wheel: 63.2 kg Turning Radius 3-wheel: 1.1 m 4-wheel: 1.
WARRANTY The manufacturer guarantees that the products manufactured by them to be free from defects in materials and workmanship for a period of one year from the date of purchase. If, within such warrant period, any such products shall be proven to be defective, such product shall be repaired or replaced, at the manufacturer’s option. To guarantee your benefits and the excellent after-sale service provided by the manufacturer, please read the following carefully.
BUYER’S REGISTRATION FORM Mobility Scooters NOTICE: SELLING DEALER SHOULD COMPLETE THIS FORM AT THE TIME OF SALE TO REGISTER WARRANTY.
MOBILITY SCOOTER CO. Est.
