ZX400/ZX410 SECURITY SYSTEM CONTROL PROGRAMMING GUIDE WWW.DIYALARMFORUM.
WWW.DIYALARMFORUM.
Table of Contents Operating The System ....................................................................................................................................... 4 1.1 1.2 1.3 1.4 1.5 1.6 Introduction .............................................................................................................................................................4 Powering Up With The Control Station .....................................................................................................
1 1.1 Operating The System Introduction The Moose ZX400/ZX410 Security System incorporates the most desired operational features available today. The ZX400/ ZX410 features ease of installation and programming with an easy-to-operate keypad. Features such as cross-zoning, delay before dialing, and an audibles “mute” function on the keypad help reduce false alarms. The ZX400/ZX410 also provides two truly independent partitions which allow the system to be divided into two distinct fully functional areas.
1 READY 2 3 4 TROUBLE 5 6 7 8 FIRE 9 10 11 12 VIEW INFO D OFF CANCEL AWAY READY TROUBLE VIEW INFO EVENT LOG ALM MEM D OFF CANCEL ALM MEM EVENT LOG 1 2 3 1 2 3 BYPASS DELAY ARM CHIME BYPASS DELAY ARM CHIME 4 5 6 4 5 6 RST SMOKE TEST PROGRAM TEST PROGRAM 7 8 9 7 8 QUIT ACCESS INSTANT CLEAR 0 ENTER QUIT ACCESS INSTANT CLEAR 0 ENTER AWAY HOME HOME NEXT A NEXT NIGHT C B 9 STAY STAY NIGHT RST SMOKE PREV SSD Control Station (ZXSSD)
For SSD and LED Control Stations only: Ready LED This LED indicates the status of the Burglar zones assigned to the Control Station’s primary area. It illuminates when the Burglar zones are all secure. Trouble LED This LED will illuminate for system troubles (AC failure, low battery, communication failure), zone troubles, and Burglar Tamper conditions. (See Section 3.2.5.2 for a complete list of trouble conditions.
1.5 KEY #6 CHIME KEY This key turns the chime function on or off for a particular area. KEY #7 RST SMOKE KEY This key resets all latched smoked detectors and clears “Smoke Troubles”. KEY #8 TEST KEY This key allows you to perform one of the six following tests: Walk, Battery, Bell, Communications, Keypad, and RF Signal Strength. After a valid passcode is entered, you may select the test to perform. KEY #9 PROGRAM KEY This key is used to enter installer or user level programming.
2 Programming the Control 2.1 Introduction The control may be programmed locally from any LED, SSD, LCD, or VFD Control Station. It may also be programmed using the remote programming software, RPM/2 Pro. 2.2 Local Programming There are two levels of Control Station programming : User level and Installer level. User level programming provides the ability to add, change, or delete user passcodes. It also allows Scheduled Arming and Latchkey operation to be changed.
Each area can be programmed to control separate outputs with a dedicated audible or annunciator. It is also possible to combine the outputs of both areas so that a central siren, bell or audible can be used. The audible should be positioned so that it can be heard by all partitions. When partitioning is not desired, simply designate all zones to a single area (Area 1).
3 Installer Level Programming 3.1 Menu Options This section will describe Installer Level Programming as performed locally from a Control Station. To enter Installer Level Programming, press the PROGRAM (9) key and enter the installer passcode (default = 9632). The Control Station will then prompt you to select a programming option from 1 to 9 where: 1 = REMOTE CONNECT 2 = SET CLOCK 3 = EDIT FUNCTION MAP 4 = EDIT ZONE NAMES 5 = DEFAULT USER CODE 1 3.1.
If the ENTER key is pressed, all changes that were entered will be range checked. The entire time and date need not be entered. Any fields that are not entered will remain unchanged. If the data entered is within range parameters, the clock will be updated and the Control Station will return to idle. A “Begin Set Clock” event will indicate the time before the change and an “End Set Clock” event will indicate the time after the change.
3.1.3.3 Programming Report Codes and Attribute Fields When the location being programmed is a report code (see sections 3.2.10 - 3.2.12) or an attribute field (see sections 3.2.1 - 3.2.3 and 3.2.12 - 3.2.13), the value will be displayed as an “H” followed by two digits. The “H” indicates that this location is a Hexadecimal field. The valid entries for these locations are “00” through “FF”, where A - F correspond with 10 - 15 respectively.
If the ENTER or CLEAR key is pressed and no changes have been made, the Control Station will return to the Zone ID prompt. If the CLEAR key is pressed and changes have been made, all changes will be cleared and the control station will return to displaying the original Zone Name. To save any changes made to the Zone Name, press the ENTER key. The control station will return to the Zone ID prompt. Press the CLEAR key to return to idle. 3.1.
3.1.7 Days Until Next Comm Test The scheduling of Automatic Communications Tests requires programming a “Comm Test Time-of-Day” and the number of “Days Between Comm Tests” as described in Section 3.2.7. If “Days Between Comm Tests” is zero, then no automatic comm tests will occur. Otherwise, a comm test will occur when a Days Until the Next Comm Test counter ticks down to zero. This function allows you to view that Days counter.
3.2.
Area Attributes 00 to FF (see the Area Attribute Table) Bypassing - enables selective bypassing of any zone that is defined as bypassable in this area. Force-Arming - permits arming of the area with zones faulted. Faulted zones are temporarily bypassed and return to operation if the fault is corrected. Only zones that are defined as bypassable may be force-armed. See Section 3.3, Programming Note 4. Exit Arm - see Section 3.3, Programming Note 3.
3.2.2 Keypad Data Descriptions Keypad Data Default Table Keypad Type Keypad Attribute Access Time (sec) KEYPAD 1 KEYPAD 2 KEYPAD 3 KEYPAD 4 KEYPAD 5 KEYPAD 6 Loc Loc Loc Loc Loc Loc Default LED [23] H-1C [24] 5 Default LED [25] H-1C [26] 5 Default SSD [27] H-1C [28] 5 Default SSD [29] H-1C [30] 5 Default LCD/VFD [31] H-1C [32] 5 Default LCD/VFD [33] H-1E [34] 5 The following table refers to programming locations 23 through 34.
3.2.
The following table refers to programming locations 35 - 166. Item Zone Type Note: Zone 29 & 30 may only be programmed as 24 Hour Fire, Verified Fire or Not Used; any other will be interpreted as Not Used. All other zones may be programmed as any zone type.
Burglar Zone Attribute Table Enter For: First Digit 0 Standard (all below disabled) 1 2 3 * * 4 5 6 7 * * * * 8 9 A B * * C D E F * * * Chime Always * Verifying * Self-Verifying * * * * Sentry Test * * Second Digit Armed AWAY only (interior) Instant * Delay 1 * * * * * * * * Armed AWAY, STAY & NIGHT (perimeter) * * * * * * * Arm STAY * * Armed AWAY & NIGHT * Follower * * Armed AWAY & STAY * Delay 2 * * * * * * * * * * * Arm NIGHT
3.2.4 User Data Description The user data block is used to set the level of authority that determines the level of activity the user can perform on the control and the areas that a particular user can perform operations on. The passcodes associated with each user may only be programmed through user level programming as described in the appropriate User Guide.
Authority Levels Authorities levels 1 through 10 are the general purpose levels with level 10 having the highest capabilities. Level 11 is for limited disarm capabilities (ie: Maid’s passcode). Level 12 is for User on Premise reporting. Level 13 is for Duress reporting. For High Level Security applications, only levels 14 and 15 should be used. If levels 14 and 15 are used, all other users should be set to Level 0 (zero).
The Installer passcode has the authority level to perform the following operations: •Access from Keypad Initiate Call to RPM/2 Pro •Arm (AWAY, STAY, NIGHT) Remote Connect •Disarm if Armed by an Installer Reset Smoke Power •Change Arming Level Program RF Data •Default User Code 1 RF Signal Strength •Edit Zone Names Set Clock •Force-Arm Silence Trouble •View & Print Event Log View Alarm Memory •Bypass Zones Battery Test •Chime Enable/Disable Bell Test •Default Function Map Comm Test •Edit Function Map (except
The following table refers to programming locations 267 through 309. Item Valid Range Output Condition See Section 3.2.5.
3.2.5.2 Programmable Output Activation The programmable outputs will be activated according to their Output Condition listed in the following table. The output will go ON STEADY for the following conditions unless otherwise specified in the table. Condition Output Becomes Active When: Fire Alarm A Fire or Verified Fire zone or an ‘A’ Key is in alarm. Fire Supervisory A zone defined as Fire Supervisory is in alarm. Duress A Duress code has been used. To turn off, press the CLEAR key for 3 seconds.
Key 6 Output ENTER + Key #6 is pressed on a keypad primary to its area. May be used to toggle an output ON/OFF. RF Annunciator Reserved for future use. Access by Keypad Any of its Control Stations have an Access timer that is running or ON. (See Section 3.3, Programming Note 18.) Quick Access By Keypad Any of its Control Stations have a Quick Access timer that is running or ON. (See Section 3.3, Programming Note 18.
Delay Before Dial 0 to 255 seconds Time in seconds that a user has after a Burglar, Holdup or Auxiliary Alarm from a zone has occurred to silence the alarm with a disarm and abort the alarm event. (See Section 3.3, Programming Note 12.) Fire Delay Before Dial 0 to 255 seconds Time in seconds that a user has after a Fire Alarm from a zone has occurred to silence the alarm and abort the alarm event. (See Section 3.3, Programming Note 13.
3.2.
T1 Dial Attempts 1 to 15 attempts Maximum number of dial attempts when the communicator dials telephone #1. T2 Dial Attempts 1 to 15 attempts Maximum number of dial attempts when the communicator dials telephone #2. On-Hook Time & Off-Hook Time 1 to 15 seconds Before the communicator dials a phone number, it seizes the phone line and goes off-hook for two seconds. It will then go back on-hook for the On-Hook Time to disconnect an existing phone connection.
NOTE The paging network setup for your area determines if your pager will work with the T2 telephone number. Dialed Digits Allowed See Section 3.1.3.2 for information on programming account codes and telephone number digits. 0-9 3.2.9 Numbers from 0 to 9 dial the appropriate Touchtone® or pulse digit. A To be determined. B Programming a B into any digit position causes the communicator to produce a Touchtone® * tone. Useful for unique applications such as voice mail, cellular, or paging applications.
Fire Phone No. 0 = Do Not Report 1 = Phone 1 Only 2 = Phone 2 Only 3 = Phone 1 (2 on Failure) 4 = Phone 2 (1 on Failure) 5 = Phone 1 and 2 Directs which telephone number(s) to report Fire Alarms, Fire Supervisories, and Restorals. 0 = Do Not Report 1 = Phone 1 Only 2 = Phone 2 Only 3 = Phone 1 (2 on Failure) 4 = Phone 2 (1 on Failure) 5 = Phone 1 and 2 Directs which phone #’s report system events.
3.2.10 Zone Report Codes Description The Zone Report Codes utilize programming locations 435 through 554. Each Zone has an alarm, restore, bypass and trouble code. The restore may be an alarm, trouble, or bypass restoral.
3.2.11 User Report Codes Description The User Report Codes utilize programming locations 555 through 654. This data block is used to program the opening and closing reports for each user code. Each report code requires a two digit entry. The first digit sets the primary event code and the second digit sets the extended code. (See Section 3.1.3.3 for Programming Report Codes).
3.2.12 System Report Codes Description Each report code requires a two digit entry. The first digit sets the primary event code and the second digit sets the extended code. (See Section 3.1.3.3 for Programming Report Codes). If the transmission format is anything other than a Pulsed format, it is only necessary to program a value other than zero into either digit to enable that event to be reported, the correct transmitted data is automatically sent.
Recent Closing Code 00 to FF Code sent in addition to a burglar alarm event if the alarm occurs within two minutes after exit time expires. Latchkey Supervision Code 00 to FF Code sent when the latchkey code is not entered during the programmed time window. User on Premises Code 00 to FF Code sent when the User on Premises (Authority Level 12) passcode is entered to disarm the system or perform the access operation.
Latch Key Schedules A Latch Key User ID is used to determine which user passcode must be entered on selected Latch Key Days. The user passcode must be entered within a time window. If the user passcode is not entered during the Time Window, a Latch key Supervision event will be posted in the Event Log to be reported.
The following table refers to programming locations 693 through 758: Item Valid Range Description Scheduled Arming Mode 0 = AWAY 1 = STAY 2 = NIGHT Determines the Auto Arm mode. Scheduled Arming Days 00 to FF (see the table below for acomplete description of each value’s activation) Selects the days of the week the system automatically arms. Sunday Arming Time 00:00 to 23:59 The time for Auto Arming on Sunday. Monday Arming Time 00:00 to 23:59 The time for Auto Arming on Monday.
3.2.14 Programming Options This section deals with the attributes of the Remote Programming Manager Software. Before programming the specific functions, it is important to understand the following: ABORT: During a remote programming session, the control is fully functional and can detect and annunciate alarms locally. The control aborts a session with RPM/2 Pro to report alarm events.
3.3 Programming Notes Note 1: Restarting Exit Time If an exit time is counting down from an AWAY arming, the exit time may be automatically restarted once to reduce false alarms. The exit time will be restarted if a Perimeter (arm in STAY mode and arm in NIGHT mode) Burglar zone is violated anytime during the last ten seconds of exit time.
Note 6: Verifying or Self-Verifying Burglar Zones If an armed Verifying Burglar zone is violated, then a forty second Verification Timer is started. If the timer expires and the zone that started it is still in violation, then the zone’s violation is verified. If another armed Burglar zone is violated while the timer is still running, then that violation verifies the first zone’s violation. If an armed Self-Verifying Burglar zone is violated, then a forty second Verification Timer is started.
Note 10: Senior Watch The Senior Watch attribute may only be used with Burglar, Critical Condition Monitor, Universal, and Universal Logged zones. It is ignored for all other zone types. If a Burglar zone has Senior Watch enabled, then the Senior Watch only applies when the zone is disarmed and not bypassed. Whenever the zone is violated, disarmed or unbypassed, the zone’s Senior Watch timer is reset to the programmed time.
Note 12: Delay Before Dial Time The Delay Before Dial Time is used as the time that a user has after a Burglar, Holdup, or Auxiliary Alarm from a zone has occurred to silence the alarm with a disarm and abort the Alarm event. If the Delay Before Dial Time is not zero and the alarm is silenced before the Delay Before Dial Time expires, then no Alarm events are posted to be reported.
bus. The interface device will send an acknowledgment to the system upon successful transmission of an event. The telephone number will not be used, but the first digit of Telephone Number 1 must not be an ‘F’. If the interface device responds back with a transmission failure or if the interface device “loses” the event, the system will view it as a failed dial attempt.
4 Digital Communicator Table For Contact ID Formats This section cross-references many of the reporting options and equivalent codes sent by Sentrol-manufactured controls when transmitting in the Contact ID formats.
Zone Auxiliary Trouble Restore 3370 Zone (1 - 28) Zone Other Trouble Restore 3370 Zone (1 - 28) Senior Watch Trouble Restore 3641 Zone (1 - 28) Zone No Response Restore 3333 Zone (13 - 29) RF Point Reporting 3381 Zone (13 - 28) Smoke Trouble Restore 3380 Zone (13 - 30) RF Sensor Tamper Restore 3383 Zone (13 - 28) RF Point Low Battery Restore 3384 Zone (13 - 28) Zone Fire Bypass Restore 3571 Zone (1 - 30) Zone Burglar Bypass Restore 3573 Zone (1 - 28) Zone Holdup Bypass Restore
5 UL Programming Requirements Underwriters Laboratories (UL) Listing This control is listed by Underwriters Laboratories (UL) as follows: Application Household Burglary (Grade A) Household Fire Listing UL 1023 UL 985 Central Station Burglary (Grade C) UL 1610/1635 Central Station Burglary (Grade B) UL 1610/1635 Home Health Care Signaling Equipment UL 1637 Local Burglary (Grade A) UL 609 Police Station Burglary Connection (Grade A) UL 365 UL has established certain requirements which pertain to
E Index A ‘A’ Key 17, 24, 25, 34, 44 AC Cycles 27 AC Power Failure 8, 26 ACCESS Key 7 Account Code 11, 33, 42 Alarm Abort 27 Alarm Indicator 24, 25, 26, 27 ALM MEM Key 6 Area Event Reporting 29, 30 Area Partitioning 8, 9 Arming 5, 6, 7, 9, 16, 34, 35, 39, 45 Auto Arm 25, 35, 37, 45 Auxiliary Alarm 24, 25, 26, 27, 42, 44 Auxiliary Keys 5 AWAY 4, 5, 15, 16, 19, 22, 23, 24, 25, 27, 35, 37, 39, 45, 46 B ‘B’ Key 15, 17, 24, 25, 34, 44 Battery Test 7, 8, 22, 23, 24, 25, 26 Bell Test 7, 22, 23, 25, 46 Burglar A
R READY 4 Receiver Compatibility 29 Remote Connect 10, 22 Remote Programming 8, 10, 38 Report Code 12, 32, 33, 34, 35, 42, 46 Reset Smoke Key 7 RF Signal Strength 7 RPM/2 Pro 8, 12, 13, 38, 45 S Scheduled Arming 8, 39 Secondary Area 17, 39 Secondary Function Keys 7 Self-Verifying 40, 46 Senior Watch 19, 27, 32, 41, 44, 45 Sentry Test 40 Set Clock 10, 11, 22 Smoke Zone 6 SSD Control Station 5, 6, 8, 9 STAY 4, 5, 15, 16, 22, 23, 24, 25, 35, 37, 39, 45 System Attributes 27 System Events 8, 31, 44 System Troub
Notes WWW.DIYALARMFORUM.
Notes WWW.DIYALARMFORUM.
WWW.DIYALARMFORUM.
sentrol controls group MOOSE a product of sentrol, inc PO Box 2904 1510 Tate Blvd. SE Hickory, NC 28603 Sales: 800.547.2556 Fax: 503.691.7566 Technical Support: 800.800.2027 WWW.DIYALARMFORUM.COM 52 Sentrol, Inc. reserves the right to change specifications without notice. ©1996 Sentrol, Inc.
