1 CHARGE THE BATCH] (1). Charge the battery equipped in the machine. ES (2). Charge the battery alone. It's suggested to charge the battery when it's equipped in the machine to get informed by the LED indicator.
earn Es Product Parts List and Schematic -1 Product technical parameters 4 Safety Instructions 5 product Introduction 8 daily maintenance -== =o mono 10 Signal Hints moo moo 1 Trouble Resolutions ooo 12 Battery Safety oo 13
PRODUCT PARTS LIS What's in box? Please check if all the accessories are in the package box.
Handle LED Power Screen Main Engine ST || 2in 1 brush Clip-on Connector Gift cleaning brush ~~ Wall bracket Aluminum Alloy Tube Switch Charging Jack Electric Floor Brush
Dust Cup Dis-dumping Lock Floor Brush Hook Cl-on Connector Rotating Connecting Ball Detachable Fluff Brush Electric Floor Brush LED Searchlight
SAFETY INSTRUCTION 01. When using electrical appliances, basic safety precautions should always be followed. 02. Check that the voltage indicated on the rating plate corresponds with that of the local network before connecting the appliance to the mains power supply. 03.
16. Do not expose the appliance to rain. 17. Do not remove from the adapter from the mains power supply by pulling the cord;switch off and remove the plug by hand. 18. Do not use the adapter to recharge nonchargeable batteries. 19. Do not use the appliance if it has been dropped or if there are visible signs of damage. 20. Do not use the appliance for anything other than its intended use. 21.
35. This appliance should not be operated by means of an external timer or separate remote control system. 386. This appliance is intended for domestic use only. It should not be used for commercial purposes. Caution: The extension tube contains electrical connections. Do not use to suck up water. Do not immerse in water for cleaning. The extension tube should be checked regularly and must not be used if damaged.
Gambling ea isles lean Aluminum-alloy Tube Installation 1. Push the aluminum-alloy tube end into the suction port of the main engine in horizon-lat direction. Make sure there is no looseness; The hearing of “click” means successful installation (as picture shows) 2. To get the aluminum alloy tube off, press the release button and pull the tube out. (as picture shows) Electric Floor Brush Installation 1. Push the floor brush into the snap joint of the aluminum alloy tube.
2-in-1 Dusting Brush Installation It can be installed in two ways: dusting brush vacuum / dusting brush tube vacuum. It's suitable for cleaning I) Operating 1. Preparation Please make sure the power is sufficient before using. It's recommended to change for 6 hours before its first use. 2. Operating Choose the right accessory for specified task. Adjustable two modes meet different needs. Press the on/off switch to make the vacuum work. Press again shifts it to the stronger mode.
DAILY MAINTENANCE Product Maintenance If's suggested to do some maintenance daily to keep the machine works regularly and to prolong its service life. 1. Main Engine (Handheld part) © Please stop the machine before cleaning © Scrub with water or neutral detergent; please dry off the cleaning cloth before cleaning; Prevent the water from flowing into inner machine. 2. Dust Cup Cleaning Regular cleaning helps to ensure product performance. The sigh = is emptying reminding.
4. Detachable Fluff Brush Cleaning Find the buckle on the left side of the floor brush head and open it up. Take out the fluff brush and remove the cords and hairs on it with scissors or the gifting cleaning brush in the package. 5. Electric Floor Brush Cleaning It is recommended to clean once after every 4 to 5 times use of the floor brush. Turn off the power switch Take off the Electric Floor Brush. Take out the fluff brush. Unplug the cover of the fluff brush' s head, clean up the dirt and hereon it.
Trouble Resolutions Common Failure Analysis and Treatment does not rotate Roller brush was blocked with hair Symptom Possible Causes 1. Connect the power adapter toe main Vacuum cleaner 1. Low battery 2 ld and charge doesn't work 2. Product suction ballet, : charge with the charging blocked seat 3. Clean up the suction inlet Product suction 1. Dust cup and the Filter 1. Clean up the dust cup is weaken component is dusty and filter material 2. The brush head was 2.
Battery Safety If the battery pack becomes exhausted, it should be removed from the product to avoid leakage. In the event of the battery pack leaking, do not allow any liquid to come into contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice. Keep the battery pack out of the reach of children.
WARNING Reed ll safety washing and instructions. Bail ta follow the warnings and instructions may result in dextrose shock, fire symbiosis salons fury. Prevent mineral staring Owe sis he of piston before connection ber pack picking p or canting the appliance. Caring th appliance with your finger on the hits or energizing pace that hav the witch on invites accidents. 2. Disconnect the battery pack from the appliance before making any adjustment, changing accessories, o storing appliance.
