DEV ISE V AHDG016 Wood 3 Drawer Mobile Cabinet V2.0 WWW.DEVAISE.
DEV ISE V IMPORTANT INFORMATION READ CAREFULLY. KEEP THIS INFORMATION FOR FURTHER REFERENCE. ••• GENERAL GUIDELINES Please read the following instruction carefully and use the product accordingly. Please keep this manual and hand it over when you transfer the product. This summary may not include every detail of all variations and considered steps. Please contact us when further information and help are needed.
DEV ISE V If you have any further questions, please feel free to contact us by email or official website: www.devaise.com We will reply ASAP. Before installation, please make sure you have all the hardware, the serial numbers are properly labeled corresponging to the list, and the quantity is correct.
DEV ISE V EXPLODED DRAWING: 5 6 6 7 2 4 3 1 8 9 10 9 X2 11 12 13 14 10 15 3/22
DEV ISE V PARTS: A X36 B X12 C X36 D X2 E X1 F X2 G X48 M4x14 = = CL + E1 X2 DL + DR H X6 + E2 X2 I X3 J X2 K X2 L X16 M X8 N X4 + CR 4/22
DEV ISE V REMARK: CR CL DR DL 1. Press the plastic part in the indicated direction to separate drawer runner E1 and E2 before assembling. 2. Please grip the E1 part while sliding the E2 part.
DEV ISE V 1. A X6 REMARK: Please do not screw A too deep or too shallow. B X4 Appropriate position Too deep Too shallow REMARK： Put a blanket under the board to avoid scratch or damage.
DEV ISE V 2. G X8 REMARK: M4x14 When installing, please make sure the screws are flattened, Not crooked; Otherwise the drawers will not be installed perfectly.
DEV ISE V 3. G X4 M4x14 T FRON E1 X2 FRO TOP NT 2 3 E1 G E1 BOTTOM G G G REMARK: 1. Please locate the holes from the back of part E1 . FRONT E1 Back: 1 2 3 9 10 11 E1 Front: 2. Then please install part G from the front of part E1 .
DEV ISE V 4. A X6 A A A A A A 5 5. C X6 3 2 4 5 C ×6 REMARK: Let the grooves on part 2 3 and 4 be connected to the groove on part 5 .
DEV ISE V 6. 6 6 2 4 5 7.
DEV ISE V 8. G G G X16 G J G K M4x14 J X2 J K 1 K X2 2 4 5 9.
DEV ISE V 10. A X4 H X2 I X1 A A A A 15 H H I 11.
DEV ISE V 12. A X4 A A A A 12 13.
DEV ISE V 14. 8 9 9 10 ×2 15.
DEV ISE V 16.
DEV ISE V 17. C X4 12 12 14 13 FR ON 12 T C C C 14 13 FRONT long C FRONT short long short 18.
DEV ISE V 19. F X2 F F 12 15 13 (1) A4 (2) Letter Size As shown in Fig. (1) installation method, the A4 Size file can be hung after installation. As shown in Fig. (2) installation method, the Letter Size file can be hung after installation. 20.
DEV ISE V 21.
DEV ISE V 22. 2 3 4 23. 1 FRONT FRONT 2 T FRON BALL BEARING T FRON REMARK: 1.Please full extend the slide runners. 2.Simply push the ball bearing cart all the way to the end of the slide(in both sides).
DEV ISE V 24. REMARK： 1. Align the slide runners on the drawer with the unit and push it carefully inside until it stops. 2. If the drawer does not go in smoothly please take it out and repeat the step. 25.
DEV ISE V 26. FRONT NT FRO long 7 short REMARK: The long shadow part is in front and the short one is inside. 7 7 REMARK: Please make the groove on board 7 match with the part N . 27.
DEV ISE V 28.
