Installation & operating instructions for USA & Canada 7600 Read the entire manual before installing and using your Morsø stove [1] A French version of the manual can be downloaded at www.morsona.
Welcome to Morsø ……. Thank you and congratulations on the purchase of your new Morsø heater. Morsø has been at the forefront of cast iron wood heater design since 1853. Each and every heater is hand built by skilled crafts-people using the best materials available. However, to extract the best performance, warmth and comfort from your heater it is essential all the installation requirements detailed within this manual are met. Please take the time to read this manual cover to cover before installation.
Table of Contents Safety Notices & Standards • Technical Specifications 2 Safety Notices & Standards 5 • Safety Notice 5 • Standards 5 • Safety Notices 6 Installation 7 • Preparation 7 • The chimney / flue system 7 • Clearances to combustible surfaces 13 • Floor Protection 15 • Mobile Home Installation 16 Safety Notice Please read the entire installation and operation manual before you install and use your new solid fuel heater.
Safety Notices • This room heater is approved for wood fuel only; Do not burn any other fuel or garbage. • If this wood heater is not installed properly, it may result in a house fire. To reduce the risk of fire follow the installation and operating instructions carefully. Failure to properly follow the installation and operation instructions may result in property damage, bodily injury or even death. • Never use chemical fire starters or fluid to start your fire.
Typical Factory-Built or Masonry Chimney Installations See page 10 for key [8] www.morsona.
Typical Installation Installation Key 1 DVL or DuraBlack 11 Tee with Tee Cap 11 Tee with Tee Cap 2 Ceiling Support Box 12 Tee Support 3 Wall Thimble 13 Chase Top Flashing 4 Chimney Pipe 14 Base Tee/Double Tee 5 Attic Insulation Shield 15 Anchor Plate or Anchor Plate with Damper 6 Flashing 16 Roof Support 7 Storm Collar 17 Finishing collar 8 Chimney Cap 18 DVL Adapter, DuraBlack Slip, Connector, or SnapLock Adapter 9 Elbow Chimney Cap Storm Collar Flashing 19 Stove Adapter 10 Elb
Flue Connection The stove is supplied from the factory with round blanking plates blocking off the top and rear flue exits (behind the rear shield plate). A cast iron flue collar is placed inside the firebox during transit. Use a 24 MSG black chimney connector or listed double wall chimney connector. Refer to local codes and the chimney manufacturer’s instructions for precautions required for passing a chimney through a combustible wall or ceiling.
Clearance Requrements Freestanding residential Installation top vent using double wall connector A. Sidewall to unit USA Canada 15” 381 mm B. Backwall to unit Floor Protection Floor protection requirements NON -COMBUSTIBLE MATERIAL BENEATH STOVE USA Canada A. Extending distance, back - 8’’(200 mm) 8’’(200 mm) 1” 26 mm B. Extending distance, right side 6” C. Cornerwall to unit 2½” 64 mm C. Extending distance, left side 6” 8’’(200 mm) D. Sidewall to connector 21” 533 mm D.
WARNING: NEVER DRAW COMBUSTION AIR FROM A WALL, FLOOR OR CEILING CAVITY OR FROM ANY ENCLOSED SPACE SUCH AS AN ATTIC OR GARAGE. DO NOT INSTALL IN A BEDROOM OR A ROOM WHERE PEOPLE SLEEP.
Operation Before you light your heater here are a few considerations. Your new Morsø heater is approved for use with Solid Wood Fuel Only. DO NOT OVERHEAT. If the heater or chimney connector glows, your heater is overheating. Use Morsø stove thermometer for correct operating temperature (#62901200). Have your chimney inspected and cleaned at least once a year by an approved and certified chimney sweep.
How to light your stove 1. How to light the stove As shown in the picture to the left you need the following: 2 fire lighthers (or 5-10 scrunched-up sheets of newspaper) 1 kg of dry kindling Approx. 2-3 lbs. of chopped firewood 2. You should always have an insulating layer of ashes from previous firings in the bottom of the fire chamber. 1” of ash is a suitable base for the wood. Start by placing a couple of logs, approzimately 1 lb., in the bottom of the burn chamber. 3.
Do not for any reason attempt to increase the air flow through your heater by altering or tampering with the air control mechanism. This could lead to serious safety and health hazards. Warning: Fireplace heaters must never be left unattended when the door(s) is open. If the door is left partly open, gas and flames may be drawn out of the heater’s opening thus increasing risks from both fire and smoke. We recommend you to fit smoke and carbon monoxide detectors in the room where the heater is installed.
Ceramic glass replacement Ceramic glass cannot be recycled because it has a higher melting point than ordinary glass. If ceramic glass is mixed with ordinary glass, the recycled material is spoiled and the recycling process may be halted. Ensure the heater’s glass does not end up with ordinary recycled waste. It should be presented separately to your local recycling center as ceramic glass.
Caution: Never empty ash when the heater is in operation. Never use your household or shop vacuum cleaner to remove ash from the heater as it may still contain hot coals. Always dispose of ash in a metal container.
[ 28 ] Date of print: 16-12-2010 www.morsona.
POS.NR.
[ 32 ] www.morsona.com Morsø Jernstøberi A/S - 19.08.