User's Manual
Table Of Contents
- 1.Safety Precautions
- 2.System Description
- 2.1About This Manual
- 2.2Introduction
- 2.3System Features
- 2.4Physical Description
- 2.5System Description
- 2.6Consecutive Point Architecture
- 2.72 + 0 (East-West) Configuration
- 2.8Spanning Tree Protocol (STP)
- 2.91+1 Protection
- 2.101 + 1 Multi-hop Repeater Configuration
- 2.11Data Interfaces
- 2.12Crosspoint Switch
- 2.13Power Management
- 2.14Event-HD Software and Network Management
- 2.15System Loopbacks
- 3.Installation
- 3.1Unpacking
- 3.2Notices
- 3.3PRE-INSTALLATION NOTES
- 3.4Back-to-Back Bench Testing
- 3.5Overview of Installation and Testing Process
- 3.6Site Evaluation
- 3.7Installation of the Event-HD
- 3.8Quick Start Guide
- 3.9SDIDU™ Service
- 4.Summary Specification
- 5.Rear Panel Connectors
- 5.1DC Input (Power) Connector
- 5.2Ethernet 100BaseTX Payload Connector 1-2
- 5.3SONET Payload Connector
- 5.4STM-1 Payload Connector
- 5.5DVB/ASI, DS-3, E-3, STS-1 Payload Connector
- 5.6NMS 10/100BaseTX Connector 1-2
- 5.7Alarm/Serial Port Connector
- 5.8ODU Connector
- 5.9T1/E1 - Channels 1-2 Connector
- 5.10T1/E1 - Channels 3-16 Connector
- 5.11USB
- 5.12Voice Order Wire
- 5.13Data Order Wire
- 6.Appendix
14 2. System Description
Alarm/Serial Interface
Alarms/Serial
DB-15HD female connector for two Form-C relay alarm
outputs (rated load: 1A @ 24 VDC), two TTL alarm
outputs, four TTL alarm inputs, and Serial Console. The
two Form-C relay alarm outputs can be configured to
emulate TTL alarm outputs.
USB Interface
USB
USB connector, reserved.
Voice Orderwire Connector
Call Button
The voice orderwire provides a PTP connection via a PTT
handset and buzzer. The call button initiates a ring.
Only the SDIDU’s™ link partner will receive the ring.
VOW does not ring all nodes or support “party line” calls.
Voice
Orderwire
RJ-45 modular port connector for voice orderwire
interface.
Data Orderwire Connector
Data
Orderwire
RJ-45 modular port connector for RS422/RS-232 data at
64 kbps.
NMS 10/100 Network Management System Connections
NMS 10/100 1
10/100Base-TX RJ-45 modular local port connector for
access to the Network Management System (SNMP) and
GUI.
NMS 10/100 2
10/100BaseTX RJ-45 modular remote port connector for
access to the Network Management System (SNMP). This
port to be used for consecutive point networks.
100/Ethernet Models: Ethernet 100BaseT Connections
USER 10/100 1
100Base-TX RJ-45 modular port connector for the local
Fast Ethernet interface.
USER 10/100 2
100Base-TX RJ-45 modular port connector. This port to
be used for consecutive point networks.
T1 Channels
T1 1-2
Two T1/E1 (RJ-48C) interface connections.
T1 3-8/16
Single Molex 60-pin connector containing 14 T1/E1
connections.
© 2007 Moseley, Inc. All Rights Reserved. 602-14886-01, Rev. A