PLEASE FOLD AND SEAL WITH TAPE ALONG OPEN END. DO NOT USE STAPLES PART NO. 1440-501 Rev.
NOTICE: PLEASE READ THE ENTIRE MANUAL BEFORE ASSEMBLING AND STARTING UP YOUR MOSQUITO MAGNET DEFENDER. TABLE OF CONTENTS 1. 2. 4. 5. 6. 7. 8. 9. 9. 10. 11. 12. 13. 14. 15. Safety…………………………..……...........................................2-4 Parts included……………………...........................................……5 Additional Components ……………….............................................6 Assembly instructions………………............................................7-9 Trap Placement……………………….............................
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment. CAUTION: The gas pressure regulator provided with this appliance must be used. This regulator is set for an outlet pressure of 11.0 in. Water Column. The gas supply must be turned off at the LP-Gas supply cylinder when this appliance is not in use.
PARTS INCLUDED ADDITIONAL COMPONENTS (1) Adaptor (1) Net (already installed) (1) Octenol Cartridge (Added Attractant) (1) Self-contained Defender powerhead (1) Reset Tool (1) Base Support (1) L-Shaped Adaptor (1) Support Pole (1) Support Leg (1) Instruction Manual IMPORTANT NOTICE Per Federal Regulations, a CO2 Cartridge has not been included with your purchase. Please visit www. mosquitomagnet.com to purchase or visit your local Mosquito Magnet dealer.
ASSEMBLY INSTRUCTIONS IMPORTANT NOTES: ASSEMBLY INSTRUCTIONS Place base upside down on a flat surface, slide Ushaped support legs into slots on base until they lock in place. 1 1. Your trap will begin capturing immediately, but allow 4-6 weeks to interrupt the breeding cycle. 2. DO NOT MOVE MOSQUITO MAGNET WITH TANK ATTACHED. DISCONNECT TANK FROM REGULATOR BEFORE RELOCATING TRAP TO AVOID DAMAGE TO REGULATOR OR TRAP. 5 Peel cover from attractant cartridge.
ASSEMBLY/STARTING INSTRUCTIONS Plug power connector into the Defender unit power slot located on the back of the power head. 9 TRAP PLACEMENT 1 Determine the direction of the prevailing wind. 2 Stand in the center of the area you are trying to protect and look toward the prevailing wind. Proper placement of the Mosquito Magnet will be 30-40 feet in front of you, within 5-6 feet of ground cover (i.e., bushes, flowerbeds, treeline, marshbed, etc.) 3 It is recommended that the trap be placed in the shade.
FOR BEST RESULTS SHUT DOWN INSTRUCTIONS To shut down the Defender simply close the valve on the propane tank and switch to “Off” position. DO NOT UNPLUG UNIT. MOSQUITO MAGNET DEFENDER MUST REMAIN PLUGGED IN FOR 5 MINUTES AFTER SHUT DOWN OR UNTIL FAN STOPS TO AVOID HEAT DAMAGE. Any open octenol or other added attractant packages should be removed and discarded. The net should also be discarded prior to storing the Mosquito Magnet Defender.
QUICK-CLEAR VALVE TROUBLESHOOTING GUIDE Recommended for use at first tank change, and every second tank change thereafter. Also recommended for use before seasonal storage to avoid build up of contaminant’s during off-season. The Quick-Clear valve is used to clear out propane contaminants in the fuel line, which may block the flow of propane from the tank to your Mosquito Magnet. The Quick-Clear valve is a gold, threaded knob located on the back of your trap.
PRODUCT REGISTRATION LIMITED WARRANTY * Mail completed form today or register on-line at www.mosquitomagnet.com First Name This warranty, (1) year from the purchase of the unit, is extended only to the original purchaser/user of products. Last Name American Biophysics Corp. warrants its products to be free from defects in materials and workmanship for the warranty period by the original purchaser/user. Address For warranty service, please contact American Biophysics Technical Center (877-699-8727).