Product Data Sheet www.moteck.com Actuator LD3 LD3 features its compact design, which is suitable for various applications that require limited installation space, such as window opener, adjustable car driver set and medical equipment. Feature - Main applications: Industrial, home care, furniture, medical - Input voltage: 12V DC / 24V DC - Max. load: 1000N (Push / Pull) - Max. static load: 2500N (Push / Pull) - Typical speed at no load: 43.9 mm/sec - Typical speed at full load: 5.
Option - Medical version (LD3M, approved according to EN60601) - Quiet version (LD3Q, noise level ≦55dB) - Positioning signal feedback with Hall effect sensor x 1 - Positioning signal feedback with Hall effect sensor x 2 - Analog positioning feedback with Potentiometer (POT) - IP Protection level: IP65 - Clamp: Clamp connection is available if rear connector is not preferred (Fig. 1) - Mounting bracket (MB22) (Fig. 2) Fig. 1 Fig.
Performance Data Model No. Gear Ratio Push / Pull Max. (N) Self-locking force Max. (N) *Typical Speed (mm/s) *Typical Current (A) Full Load No Load No Load Full Load 24V 12V 24V 12V Noise Level (dB) LD3(M)-XX-05-K3... 5:1 150 2500 43.9 36.5 0.6 1.2 1.6 3.2 ≦70 LD3(M)-XX-10-K3... 10:1 250 2500 27.6 23.5 0.6 1.2 1.6 3.2 ≦70 LD3(M)-XX-20-K3... 20:1 500 2500 14.6 12.3 0.6 1.2 1.6 3.2 ≦70 LD3(M)-XX-30-K3... 30:1 800 2500 9.5 7.5 0.6 1.2 1.6 3.
Dimensions Regular version (LD3) & Quiet version (LD3Q) ø30.5 18 ø20 ● Basic 72 95 42 S ø40 A 12 ø20 9 ø8 24 18 36.7 82 ø8 ø30.5 18 ø20 ● With Hall effect sensor 90 20 12 9 ø8 24 18 36.7 82 ø8 S ø42 A 42 ø20 114 ø30.5 18 ø20 ● With Potentiometer 72 20 12 9 ø8 36.7 24 18 82 ø8 S Ø40 A 42 ø20 132 Note: As an example in 0° orientation for rear connector.
ø20 18 ● Basic ø30.5 Medical version (LD3M) 81.6 104.6 A 42 S ø40 12 ø20 9 ø8 24 18 36.7 82 ø8 ø30.5 18 ø20 ● With Potentiometer 81.6 141.6 20 S A ø40 12 ø20 9 ø8 24 18 36.7 82 ø8 42 Note: As an example in 0° orientation for rear connector. ● Installation Dimension Retracted length (A) Option Standard or Hall sensor POT Front connector code Stroke (S) 50 100 150 200 250 300 1 158 209 260 311 362 413 3 199 250 301 352 403 454 6 168.5 219.5 270.
● Front Connector 3: Spherical rod eye D D 6: Plastic slot D W ø20 ø20 1: Drilled hole 9 H 10.5 ● Rear connector 1: Zinc alloy clevis, 0° 18 3: Zinc alloy clevis, 90° D 18 8 12 D 8 12 Front connector code Diameter of pivot without bushing (D) Slot width (W) Slot depth (H) 1 ø6.4, ø8, ø10 N/A N/A 3 ø8 N/A N/A 6 ø8, ø10 6 15 Rear connector code 1 ø6.4, ø8, ø10 N/A N/A 3 ø6.
● Clamp 30 1.3 77.2 36.8 2 ø8.1 15 22 ø6.5 22 ● Mounting bracket (MB22) 39.
Compatibility Regular version (LD3) & Quiet version (LD3Q) Product Model Control box LD3 & LD3Q spec T Control, CS1, CS2, CBT2, CB3T, CB4M - Without positioning sensor feedback - 4-Pin Moteck F-type DIN plug CB2P, CB4P, CB4P-HP, MD6C, MD7C - Without positioning sensor feedback - 4-Pin Moteck H-type or V-type DIN plug CB3T-SY, CB3T-SYD, CB4M-S, CB4M-B - With dual Hall effect sensors - 6-Pin Moteck F-type DIN plug Medical version (LD3M) Product Model Control box CB2P, CB4P, CB4P-HP, MD6C, MD7C L
Wiring Wire definitions: ● Without positioning sensor feedback Power Red Black M+ M- Note: 1. Connect Red (M+) to ‘+’ & Black (M-) to ‘-’ of DC power, the actuator will extend. ● With Hall effect sensor x 1 Power Signal Red Black White Yellow Blue M+ M- GND VCC DATA Note: 1. Connect Red (M+) to ‘+’ & Black (M-) to ‘-’ of DC power, the actuator will extend. 2. Hall effect sensor resolution Gear ratio 5:1 10:1 20:1 30.1 40:1 Resolution (pulses/mm) 2.27 3.62 6.86 11.0 14.5 3.
● With Potentiometer (POT) Power Signal Red Black White Yellow Blue M+ M- GND VCC Data Note: 1. Connect Red (M+) to ‘+’ & Black (M-) to ‘-’ of DC power, the actuator will extend. 2. The resistance between blue and white wires increases when the actuator extends, and decreases when it retracts. 3. Potentiometer resistance Stroke (mm) Resistance (tolerance: ±0.3KΩ) 50 0.3 ~ 9.3K 100 0.3 ~ 9.7K 150 0.3 ~ 8.6K 200 0.3 ~ 9.6K 250 0.3 ~ 9.3K 300 0.3 ~ 9.3K 4.
Ordering Key Regular version LD3 - 24 - 10 - K3 - 100 - C 1 1 - HS2 - 54 - M2 - C Input voltage 12: 12V DC 24: 24V DC Gear ratio 05, 10, 20, 30, 40 (Refer to Performance Data) Motor and Spindle type K3 (Refer to Performance Data) Stroke 050: 50 mm 100: 100 mm 150: 150 mm 200: 200 mm 250: 250 mm 300: 300 mm Front connector 1: Drilled hole 3: Spherical rod eye 6: Plastic slot (Refer to page 6) Rear connector 1: Zinc alloy clevis, 0° 3: Zinc alloy clevis, 90° (Refer to page 6) Positioning feedbac
Quiet version LD3Q - 24 - 10 - D3 - 100 - C 1 1 - HS2 - 54 - M2 - C Input voltage 12: 12V DC 24: 24V DC Gear ratio 20, 30 (Refer to Performance Data) Motor and Spindle type D3 (Refer to Performance Data) Stroke 050: 50 mm 100: 100 mm 150: 150 mm 200: 200 mm 250: 250 mm 300: 300 mm Front connector 1: Drilled hole 3: Spherical rod eye 6: Plastic slot (Refer to page 6) Rear connector 1: Zinc alloy clevis, 0° 3: Zinc alloy clevis, 90° (Refer to page 6) Positioning feedback Blank: None HS1: Hall e
Medical version LD3M - 24 - 10 - K3 - 100 - C 1 1 - POT - 65 - M2 - C Input voltage 12: 12V DC 24: 24V DC Gear ratio 05, 10, 20, 30, 40 (Refer to Performance Data) Motor and Spindle type K3 (Refer to Performance Data) Stroke 050: 50 mm 100: 100 mm 150: 150 mm 200: 200 mm 250: 250 mm 300: 300 mm Front connector 1: Drilled hole 3: Spherical rod eye 6: Plastic slot (Refer to page 6) Rear connector 1: Zinc alloy clevis, 0° 3: Zinc alloy clevis, 90° (Refer to page 6) Positioning feedback Blank: No
Certifications Regular version The LD3 actuctor is compliant with the following regulations, in terms of the essential conformity requirements of EMC Directive of 2014/30/EU. Emission Immunity EN 55014-1:2006+A1:2009+A2:2011 EN 55014-2:1997+A1:2001+A2+:2008 Catagory I Medical version The LD3M actuctor is compliant with the following regulations, in terms of the essential conformity requirements of MDD Directive of 93/42/EEC.
