EDITION - V 1.
helio C2 Maintenance manual& warranty information Dealer: This manual must be given to the user of the HELIO C2 wheelchair before its first use. User: Prior to using the HELIO C2 wheelchair, carefully read this manual and keep it for future reference. For more information about this product, its parts/accessories and the services provided, please visit : www.motioncomposites.com HELIO C2 What a folding wheelchair should be. Thank you for selecting the HELIO C2 wheelchair.
EDITION - V 1.0 User Manual High-Modulus Carbon T700 - The lightest and most rigid material available, also renowned for its vibration dampening properties. Rigid Unibody Frame - A unibody frame is much stronger and needs less maintenance than a standard two-part frame. It also reduces weight while maximizing propulsion efficiency. Symmetrical Molded Crossbrace 3D - Entirely symmetrical carbon fiber crossbrace for reduced torsion and a better distribution of forces throughout the frame.
helio C2 Table of contents WELCOME TO HELIO C2 CONTACTING US IMPORTANT INFORMATION 2 TABLE OF CONTENTS 4 3. PRODUCT OVERVIEW PARTS LIST 5 4. 4.1 4.2 BEFORE USE GENERAL WARNING SYMBOLS 6 5. 5.1 5.2 5.3 TECHNICAL SPECIFICATIONS STRUCTURE DIMENSIONS ADJUSTABILITY 6 6. 6.1 6.2 6.3 SAFETY PERIODIC CHECKLIST WEIGHT LIMITATION WEIGHT TRAINING AND SPORTING ACTIVITIES 7 7. TUTORIAL 7 8. 8.1.1 8.1.2 8.1.3 8.2 8.2.1 8.2.2 8.2.3 8.2.4 8.2.5 8.2.6 8.2.7 8.2.8 8.2.9 8.2.10 8.2.11 8.2.12 8.2.
EDITION - V 1.0 User Manual 3.
helio C2 4. Before use Initial setup of your HELIO C2 wheelchair must be done by a qualified technician. 4.1 General Warning Your HELIO C2 wheelchair has been designed by professionals with proper use of aluminium in mind. DO NOT TRY TO MODIFY THE FRAME BY ANY MEANS. THE FRAME MAY BE SEVERELY DAMAGED IN THE EVENT OF DRILLING AND GRINDING, THUS VOIDING THE WARRANTY. Only use Motion Composites approved and designed clamps and accessories on your HELIO C2 wheelchair.
EDITION - V 1.0 6. Safety 6.1 Periodic Checklist See related appendix (section 14). 6.2 Weight Limitation The HELIO C2 wheelchair has a weight limit of 250 lbs (or 350 lbs with an HD kit). The specified weight capacity includes: both the rider and any luggage. A user with a 10lb backpack, for example, should not exceed a weight of 240 lbs (or 340 lbs with the HD kit). It is of utmost importance that the total weight be below the above specified capacity.
helio C2 8.2 Riding your wheelchair Various adjustments of your wheelchair (seat height/ depth/system, back angle, rear & front wheels camber/ size/position, position of the front riggings) could affect the center of gravity. The adjustments should be performed by a professional and the wheelchair user should be aware that the stability could be affected by these adjustments. Do not tilt the wheelchair or perform a wheelie without assistance if you are a new wheelchair user. 8.2.
EDITION - V 1.0 8.2.10 Moving with Assistance Caregivers should read the “Caregiver” section of this manual. 1 - Going up a curb or step • Place yourself behind the wheelchair. • Go forward and tilt the wheelchair with the rear wheels by making sure that the front casters do not touch the curb or the step. • Once the front wheels are elevated and you have passed the obstacle, put them back on the ground and continue pushing the wheelchair.
helio C2 9.3 Front Riggings 9.3.1 Installing • Insert the front rigging pivot into the wheelchair’s mounting tube. • Rotate the assembly toward the front until the mechanism locks into place. • Repeat the same steps for the other side. 9.3.2 Uninstalling 9.5.1 Flip-back armrests To lift the armrests: • Pull lever (1) upwards to release the system. • Rotate the armrest all the way up and down.
EDITION - V 1.0 9.5.3 Swing-Away Armrests To remove the armrests from the wheelchair: • Lift them slightly to release the armrest (1). • Rotate them outwards. • To reinstall the armrests, rotate them back in until they set into place (1). 9.6 Seat belts Use positioning belts ONLY to help support the rider’s posture. Improper use of these belts may cause severe injuries to the rider. Make sure the rider does not slide down in the wheelchair seat.
helio C2 10. Adjustments and maintenance of your HELIO C2 10.1 Service Refer to your dealer for service. A complete and updated list of service providers can be found on our website. 10.2 Replacement Parts Ordering information: Consult our website to download the parts manual and view ordering information. Please contact us at: Motion Composites Inc. 519 J-Oswald Forest, suite 101 Saint-Roch-de-l’Achigan, Quebec J0K 3H0 Canada Phone: 1-866-650-6555 Fax: (450) 588-0200 support@motioncomposites.com www.
EDITION - V 1.0 10.5.4 Adjusting the Backrest Height • Loosen the screw (1) that holds the back upholstery. • Pull backrest upholstery down several centimetres in order to access screw (2) that holds the push handle. • Remove screw (2) and the backrest handle. • To adjust the backrest height, with the help of a threaded rod (¼”-20), move the dowel nut (3), which is located inside the handle. • Once this step is completed, use screw (2) to hold the dowel nut (3) while removing the threaded rod.
helio C2 10.6.4 Replacing Armrest Pad • Remove screws (1) located under pad (through the tube). • Replace with new armrest pad. • Reinstall screws (1) and tighten firmly. 10.6.6 Adjusting Swing-away Armrest height • Pull the armrest out of the receiver (1). • Remove screws (2). • Inside the armrest tube, slide the dowel nut with a long screwdriver at the desired height (3) • Reinstall screws (2). • Reinsert armrest in receiver. 10.6.
EDITION - V 1.0 10.8 Seat It may be difficult to unfold the wheelchair if the seat upholstery has been installed too tight. 10.8.1 Replacing Seat Upholstery • Remove end cap (1). • Slide in new seat upholstery. • Reinstall end cap (1) • Adjust tension with the velcro located under the seat upholstery. • Fully open the wheelchair and make sure the upholstery is tight. The seat rails must be snapping easily in the seat rail supports. • Firmly tighten all screws on the seat rails.
helio C2 10.10.3 Removing/Installing the stem bolt assembly Transit securement points are to remain in their original positions. Transit securement points are only designed to be used in their original position facing forward. Do not rotate transit securement points inward. • Remove the caster housing from the frame. • Remove plastic cap (1). • Loosen lock nut (2) while holding the stem bolt (3) from the bottom to prevent the fork from turning.
EDITION - V 1.0 10.11.2 Replacing/Adjusting hand rims • Use a plastic tire removal tool to take off the tire. • Remove all nuts inside the rim. • Replace the handrim with a new one and align the mounting holes. • Reinstall and tighten the nuts firmly. • Reinstall the tire on the rim. 10.11.3 Adjusting the rear axle height • Loosen the two nuts holding the axle bushing. • Move axle bushing along (1) mounting plate (2). • Reinstall the bushing in the desired mounting hole. 10.11.
helio C2 10.13 Extension brakes 10.13.1 Replacing/Adjusting the brake extension • Loosen screw (1). • Align eyelet (2) with the mounting hole. • Re-tighten screw (1) on the brake lever. 10.14 Anti-tippers 10.14.1 Adjusting the Height of the Anti-tippers The anti-tippers should be between 1½ and 2 ¾ inches (40 to 70 mm) off the ground. Improper spacing may result in wheelchair hang ups over obstacles or not preventing the wheelchair from tipping.
EDITION - V 1.0 User Manual 11.16 Amputee extention plate 11 Using a paratransit service 10.16.1 Installing an amputee plate 11.1 About paratransit vehicles • Install mounting plate (1) by closing the clamps around the frame. • Insert a second axle receiver (2) on the axle plate • Install the back clamp (3) onto the rear of the frame.
helio C2 12 Motion Composites limited warranty A. Frame – 5 years Motion Composites warrants the wheelchair frame and cross braces against defects in materials and workmanship for five years from the date of purchase. B. Components – one year Motion Composites warrants all Motion Composites-made components against defects in materials and workmanship for one (1) year from the date of purchase, except for parts listed below. C.
EDITION - V 1.
helio C2 14. Safety Inspection Checklist Action Frequency At every use Make sure wheelchair rolls easily and straight. √ Check for vibrations, noise or any deviation from normal functioning. √ Ensure wheel locks are working properly. √ Check that both rear wheel quick-releases are locked. √ Ensure that front stem is perpendicular to floor. √ Visually inspect tires (front & rear) for debris, low pressure, flat spots or wear. √ Make sure anti-tip tubes are locked in place (if equipped).
EDITION - V 1.0 15 PARTICULAR DAMAGES User Manual 15.2 Special damages that require the return of the wheelchair to the manufacturer 15.1 Damages requiring service by a qualified service agent If any of the following conditions are observed, always contact your service agent prior to sending your wheelchair for repairs at Motion Composites.
helio C2 Motion Composites Inc. 519 J-Oswald Forest, suite 101 Saint-Roch-de-l’Achigan, Quebec J0K 3H0 Canada Phone: 1-866-650-6555 Fax: (450) 588-0200 support@motioncomposites.com www.motioncomposites.com Conversion chart Inches Metric Inches Metric Inches Metric Inches Metric 1/4” 0.63 mm 1” 2.54 cm 10” 25.40 cm 19” 48.26 cm 1/3” 0.84 mm 2” 5.08 cm 11” 27.94 cm 20” 50.80 cm 1/2” 1.26 mm 3” 7.62 cm 12” 30.48 cm 21” 53.34 cm 3/4” 1.90 mm 4” 10.16 cm 13” 33.