Datasheet

www.symcom.com • 800-843-8848 • fax: [phone]
16
Available Models:
Auxiliary Products:
• CIO-601CS-DN-P1
Features:
• Ground fault warning (enable/delay)
• Ground fault trip (enable/trip delay)
• Ground fault motor acceleration (enable/trip
delay)
• Modbus communications watchdog
A pprovals:
601-CS-D-P1
Specications
The 601-CS-D-P1
3-phase power monitor is a fully programmable
electronic power monitor designed to monitor
3-phase systems. The 601-CS-D-P1 has a single
relay that can be configured as a general purpose
network output or to trip on ground faults. The
601-CS-D-P1 monitors ground fault current,
phase currents, phase voltages, power factor and
frequency. The RS485MS-2W communications
module allows the 601-CS-D-P1 to communicate
using the Modbus RTU protocol. The Modbus
connection can be used to monitor power
parameters, setup the device or control the fault
relay. A DeviceNet™ communications I/O module
(CIO-601CS-DN-P1) is available as well. This CIO
module only works with the 601-CS-D-P1 unit.
It is used for sending the information from the
601-CS-D-P1 over a DeviceNet™ network. It also
provides I/O capabilities and the ability to set the
parameters of the 601-CS-D-P1.
**Note: This product must be used with an
external Zero-Sequence CT for proper operation
(not included).
For more information see:
See Appendix A, page 66, Figure 1 for dimensional
drawing.
See Appendix B, page 73, Figure 7 for typical wiring
diagrams.
Model 601-CS-D-P1
monitors a zero-sequence CT for high accuracy ground fault protection
Ground Fault Monitor
Pollution Degree ...............................3
Class of Protection ..............................IP20
Relative Humidity ..............................10-95%, non-condensing per IEC 68-2-3
Terminal Torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7in.-lbs.
Standards Passed
Electrostatic Discharge (ESD) .....................IEC 61000-4-2, Level 3, 6kV contact, 8kV air
Radio Frequency Immunity, Conducted ...........IEC 61000-4-6, Level 3 10V
Radio Frequency Immunity, Radiated .............IEC 61000-4-3, Level 3, 10 V/m
Fast Transient Burst .............................IEC 61000-4-4, Level 3, 3.5kV input power
Short Circuit Rating .............................100kA RMS, SYM, 600VAC max.
Surge Immunity
IEC ...........................................IEC 61000-4-5, Level 3, 2kV line-to-line;
Level 4, 4kV line-to-ground
ANSI/IEEE ....................................C62.41 Surge and Ring Wave Compliance to a
level of 6kV line-to-line
High Potential Test .............................Meets UL508 (2 x rated V +1000V for 1 minute)
Safety Marks
UL ............................................UL508 (File #E68520)
CE ............................................IEC 60947-1, IEC 60947-5-1
Max Conductor Size (with insulation) .............0.65”
Dimensions ....................................3.05 H x 3.85 W x 5.05 D in.
(77.47 x 97.79 x 128.27 mm)
Weight ........................................1.2 lbs. (19.2 oz., 544.31 g)
Mounting Method ..............................Surface mount (4 - #8 screws) or
DIN rail mount
Input Characteristics
Line Voltage ...................................200-480VAC
Frequency .....................................50/60Hz
Motor Full Load Amp Range .....................0.5-175A (direct)
176-800A (CTs required)
Input Ground Fault Current .....................0.5-10A
Output Characteristics
Output Contact Rating (SPDT)
Pilot Duty .....................................480VA @ 240VAC
General Purpose ................................10A @ 240VAC
Expected Life
Mechanical ....................................1 x 10
6
operations
Electrical ......................................1 x 10
5
operations at rated load
General Characteristics
Ambient Temperature Range
Operating. ......................................... -20
° to 70 ° C (-4 ° to 158 ° F)
Storage. ........................................... -40
° to 80 ° C (-40 ° to 176 ° F)
Accuracy at 25° C (77° F)
Voltage ........................................+1%
Current ........................................+3% (<175A direct)
GF Current ....................................+3%
Repeatability
Voltage ........................................+0.5% of nominal voltage
Current ........................................+1% (<175A direct)
Maximum Input Power ..........................10 W
CATALOG_SYMCOM_2014.indd 16 6/10/14 11:06 AM