Manual

ManualsBrandsMotorGuide ManualsWater equipmentX3-40

eng i

EU Compliance Statement

Attwood Corporation hereby declares that the Motorguide X3 trolling motor is in

compliance with the essential requirements and other relevant provisions of the

99/5/EC R&TTE directive.

A copy of the original CE Declaration of Conformity is on our website at http://

www.motorguide.com/support/certifications.

Thank You

Thank you for choosing MotorGuide, one of the finest trolling motors available.

Years of experience have been committed to the goal of producing the finest

quality products. This led to MotorGuide's reputation for strict quality control,

excellence, durability, long‑lasting performance and being the best at providing

after‑the‑sale service and support.

Please read this manual carefully before operating your motor. This manual has

been prepared to assist you in the operation, safe use, and care of your trolling

motor.

Again, thank you for your confidence in MotorGuide.

Warranty Message

The product you have purchased comes with a Two Year Limited Warranty

from MotorGuide, the terms of the policy are set forth in the Warranty

Information section of this manual. The policy statement contains a description

of the duration of coverage, important disclaimers and limitations of

damages, and other related information. Please review this important

information.

The description and specifications contained herein were in effect at the time

this manual was approved for printing. MotorGuide, whose policy is one of

continued improvement, reserves the right to discontinue models at any time, to

change specifications, designs, methods, or procedures without notice and

without incurring obligation.

MotorGuide, Lowell, Michigan U.S.A.

part without permission is prohibited.

Alpha, Axius, Bravo One, Bravo Two, Bravo Three, Circle M with Waves Logo,

K‑planes, Mariner, MerCathode, MerCruiser, Mercury, Mercury with Waves

Logo, Mercury Marine, Mercury Precision Parts, Mercury Propellers, Mercury

Racing, MotorGuide, OptiMax, Quicksilver, SeaCore, Skyhook, SmartCraft,

Sport‑Jet, Verado, VesselView, Zero Effort, Zeus, #1 On the Water and We're

Driven to win are registered trademarks of Brunswick Corporation. Pro XS is a

trademark of Brunswick Corporation. Mercury Product Protection is a registered

service mark of Brunswick Corporation.

X3-40/X3-45/X3-55/X3-70 90-8M0055861 1213

Summary of content (36 pages)

PAGE 1
Attwood Corporation hereby declares that the Motorguide X3 trolling motor is in compliance with the essential requirements and other relevant provisions of the 99/5/EC R&TTE directive. A copy of the original CE Declaration of Conformity is on our website at http:// www.motorguide.com/support/certifications. 90-8M0055861 1213 EU Compliance Statement Thank You Please read this manual carefully before operating your motor.
PAGE 2
eng ii
PAGE 3
Warranty Information MotorGuide Limited Two Year Warranty...................................................................... 1 General Information Boater's Responsibilities.............................................................................................. 3 Protecting People in the Water.................................................................................... 3 Passenger Safety Message.........................................................................................
PAGE 4
Maintenance Trolling Motor Care.................................................................................................... 25 Inspection and Maintenance Schedule...................................................................... 25 Lubrication Points....................................................................................................... 26 Battery Inspection......................................................................................................
PAGE 5
WARRANTY INFORMATION MotorGuide Limited Two Year Warranty KEEP YOUR ORIGINAL PURCHASE RECEIPT eng 1. To obtain warranty service, the purchaser should deliver or return the unit (postage prepaid and insured) to any MotorGuide authorized service center. DO NOT RETURN TO PLACE OF PURCHASE unless they are an authorized service center. Motors purchased in other countries should be returned to place of purchase.
PAGE 6
WARRANTY INFORMATION 6. This warranty does not apply to normal worn parts, i.e., worn cables, adjustments, or product damage due to 1) neglect, lack of maintenance, accident, abnormal operation or improper installation or service; 2) abuse, i.e., bent metal columns, bent armature shafts, broken control cables, etc.
PAGE 7
GENERAL INFORMATION Boater's Responsibilities The operator (driver) is responsible for the correct and safe operation of the boat and safety of its occupants and general public. It is strongly recommended that each operator (driver) read and understand this entire manual before operating the trolling motor. Be sure at least one additional person on board is instructed in the basic operation of the trolling motor in case the driver is unable to operate the boat.
PAGE 8
GENERAL INFORMATION Use flotation devices. It is the law to have an approved personal flotation device of suitable size for each person aboard and have it readily accessible. Do not overload your boat. Most boats are rated and certified for maximum load (weight) capacities, refer to your boat capacity plate. If in doubt, contact your dealer or the boat's manufacturer. Perform safety checks and required maintenance. Follow a regular schedule and ensure all repairs are made properly.
PAGE 9
PRODUCT OVERVIEW X3‑40/X3‑45/X3‑55/X3‑70 MotorGuide Trolling Motor CABLE STEER MODELS a b c d m e f l g k h i j 54509 eng 5 abcdefgh- Directional indicator Mount bracket Battery cables Latch release handle Speed control Three‑position switch Foot pedal Serial number decal (under the foot pedal) i - Momentary switch j - Propeller k - Lower unit l - Composite column m - Bracket door knob
PAGE 10
PRODUCT OVERVIEW HAND-OPERATED MODELS a a - Top housing b - Extendable speed control tiller handle c - Serial number decal d - Battery cables e - Latch release handle f - Mount bracket g - Composite column h - Propeller i - Lower unit j - Bracket door knob k - Steering tension collar l - Depth adjustment collar b c l d k j e f g i h 54512 Specifications Model Peak Thrust Shaft Volts Speeds Forward/ Reverse Control X3‑45 FW 20.4 kgf (45 lbf) 127.0 cm (50 in.
PAGE 11
PRODUCT OVERVIEW eng Model Peak Thrust Shaft Volts Speeds Forward/ Reverse Control X3‑55 FW 24.9 kgf (55 lbf) 91.4 cm (36 in.) 12 V 5 Foot Pedal/ Cable Steer X3‑55 FW 24.9 kgf (55 lbf) 106.7 cm (42 in.) 12 V 5 Foot Pedal/ Cable Steer X3‑55 FW 24.9 kgf (55 lbf) 114.3 cm (45 in.) 12 V 5 Foot Pedal/ Cable Steer X3‑55 FW 24.9 kgf (55 lbf) 127.0 cm (50 in.) 12 V 5 Foot Pedal/ Cable Steer X3‑70 FW 31.8 kgf (70 lbf) 114.3 cm (45 in.
PAGE 12
WIRING AND BATTERY INFORMATION Wiring and Battery Information ! WARNING An operating or charging battery produces gas that can ignite and explode, spraying out sulfuric acid, which can cause severe burns. Ventilate the area around the battery and wear protective equipment when handling or servicing batteries.
PAGE 13
WIRING AND BATTERY INFORMATION When charging batteries, an explosive gas mixture forms in each cell. Part of this gas escapes through holes in the vent plugs and may form an explosive atmosphere around the battery if ventilation is poor. This explosive gas may remain in or around the battery for several hours after it has been charged. Sparks or flames can ignite this gas and cause an internal explosion, which may shatter the battery. The following precautions should be observed to prevent an explosion: 1.
PAGE 14
WIRING AND BATTERY INFORMATION Wire Color Code Abbreviations Wire Color Abbreviations BLK Black BLU Blue BRN Brown GRY Gray GRN Green ORN or ORG Orange PNK Pink PPL or PUR Purple RED Red TAN Tan WHT White YEL Yellow LT or LIT Light DK or DRK 10 Dark eng
PAGE 15
WIRING AND BATTERY INFORMATION Battery Connection ! CAUTION Disconnecting or connecting the battery cables in the incorrect order can cause injury from electrical shock or can damage the electrical system. Always disconnect the negative (‑) battery cable first and connect it last. 12-VOLT BATTERY CONNECTION 1. Install a 50‑amp (good) or 60‑amp (best) manual reset circuit breaker in line with the trolling motor power cable positive (+) lead and the battery positive (+) terminal.
PAGE 16
WIRING AND BATTERY INFORMATION Starting with the positive (+) lead, reconnect the battery cables to the engine starting battery. a d BLK Y GR RED 5.
PAGE 17
TROLLING MOTOR INSTALLATION AND OPERATION Mount Bracket Installation c a - X3 bow mount bracket b - Latch release handle c - Bracket door knob b a 54513 IMPORTANT: Choose an area on the boat deck that allows a 7.6 cm (3 in.) clearance between the bow of the boat and the column of the trolling motor. 1. Select an appropriate area on the deck of the boat to install the mount. Ensure that the forward mounting screws will not penetrate the hull. a 54514 a - Clearance 7.6 cm (3.0 in.) 2.
PAGE 18
TROLLING MOTOR INSTALLATION AND OPERATION IMPORTANT: A minimum of four mounting bolts are required to mount the trolling motor to the boat. Spread the mounting bolts as far apart as practical for the most secure mounting. a - Mount bracket mounting holes a a 54516 3. Drill the mounting holes with a 7 mm (1/4 in.) diameter drill bit. Remove any debris. IMPORTANT: Using a larger drill bit, countersink the holes on fiberglass boats to prevent cracking. 4.
PAGE 19
TROLLING MOTOR INSTALLATION AND OPERATION IMPORTANT: If necessary, shim the rubber washers with 25 mm (1 in.) outside diameter stainless steel washers to create a level mounting surface. a a b b c g d d e e f abcdefg6. f 52406 Mount bracket Mounting bolt Rubber isolator Deck Washer Nylon locking nut Carpet Once installed, the bracket should fasten securely and evenly, with the latch pins in the slots, and release with a light, easy pull on the rope handle.
PAGE 20
TROLLING MOTOR INSTALLATION AND OPERATION 4. Use four #8 x 2 in. stainless steel screws to secure the foot pedal to the boat deck. 54589 Installing the Motor into the Bow Mount a - Steering tension collar (hand‑operated models only) b - Bracket door c - Bracket door knob a b c 54517 1. Turn the bracket door knob counterclockwise to loosen and open the bracket door. 2. Place the motor column into the bracket and close the door. 3.
PAGE 21
TROLLING MOTOR INSTALLATION AND OPERATION Stowing the Trolling Motor ! WARNING Rotating propellers can cause serious injury or death. Never start or operate the motor out of water. ! CAUTION Moving parts, such as hinges and pivot points, can cause serious injury. Keep away from moving parts when stowing, deploying, or tilting the motor. 1. Firmly grasp the latch release handle. 2. Snap the latch release handle to disengage the lock pin. 3.
PAGE 22
TROLLING MOTOR INSTALLATION AND OPERATION 5. Position the tie‑down strap over the composite column and through the buckle. Pull it tight, then secure the hook‑and‑loop backing together to secure the motor to the mount bracket. a - Tie‑down strap a 54587 Deploying the Trolling Motor ! WARNING Rotating propellers can cause serious injury or death. Never start or operate the motor out of water. ! CAUTION Moving parts, such as hinges and pivot points, can cause serious injury.
PAGE 23
TROLLING MOTOR INSTALLATION AND OPERATION IMPORTANT: Gently lower the trolling motor into the water. Do not release the latch release handle until the lock pin is engaged. a - Latch release handle a 54519 5. Once the motor is in the deployed position, the lock pin will engage to secure the trolling motor. a - X3 in the deployed position a 54521 Adjusting the Steering Tension (Hand‑Operated Motors Only) Adjust the steering tension collar to increase or decrease the effort to turn the motor freely. 1.
PAGE 24
TROLLING MOTOR INSTALLATION AND OPERATION 2. To reduce the steering tension, turn the steering tension collar counterclockwise. a - Steering tension collar a 54522 Adjusting the Motor Depth ! CAUTION Avoid possible serious injury from dropping the motor when adjusting the motor depth. Firmly grasp the motor shaft with one hand when raising or lowering the motor. HAND-OPERATED MODELS Adjust the depth of the motor to improve trolling motor performance in various water depths.
PAGE 25
TROLLING MOTOR INSTALLATION AND OPERATION CABLE STEER MODELS IMPORTANT: When adjusting the motor depth, ensure that the propeller blades are fully submerged 15–30 cm (6–12 in.) below the water surface to avoid ventilation. 1. Firmly grasp the column with one hand. 2. Loosen the bracket door knob until the motor column slides freely. 3. Raise or lower the motor column until the propeller blades are submerged 15–30 cm (6–12 in.) below the water surface, then tighten the collar.
PAGE 26
TROLLING MOTOR INSTALLATION AND OPERATION Directional Indicator—Cable Steer Models The indicator provides directional information at a glance.
PAGE 27
TROLLING MOTOR INSTALLATION AND OPERATION Speed Control—Cable Steer Models FIVE-SPEED AND VARIABLE SPEED MOTORS Foot operated motors are five‑speed models. Control the speed of your motor by rolling the speed control knob with your hand or foot until you reach the desired speed.
PAGE 28
TROLLING MOTOR INSTALLATION AND OPERATION Speed Control Adjust the speed control (five forward speeds and two reverse speeds) to the desired direction and thrust level. Rotate the twist‑tiller handle clockwise for forward movement and counterclockwise for reverse movement. The "off" handle position stops the motor.
PAGE 29
MAINTENANCE Trolling Motor Care To keep your trolling motor in the best operating condition and retain its dependability, it is important that your trolling motor receive periodic inspections and maintenance. We urge you to keep it maintained properly to ensure the safety of you and your passengers. ! WARNING Neglecting to inspect, maintain, or repair your trolling motor can result in product damage or serious injury or death.
PAGE 30
MAINTENANCE IMPORTANT: Trolling motors stored in temperatures below 0 °C (32 °F) should be operated slowly for a minimum of 15 minutes before going above 30% operation. Lubrication Points NOTE: Preferred lubricants can be obtained at any authorized MotorGuide or Mercury Marine service center.
PAGE 31
MAINTENANCE IMPORTANT: Read the safety and maintenance instructions which accompany your battery. 1. Ensure that the battery is secured to the vessel. 2. Ensure that the battery cable terminals are clean, tight, and correctly installed. For installation instructions, refer to Battery Connection. 3. Ensure that the battery is equipped with a battery box to prevent accidental shorting of the battery terminals.
PAGE 32
MAINTENANCE INSTALLING THE PROPELLER 1. Rotate the motor shaft to insert the propeller pin horizontally. a - Propeller pin a 44664 2. Install the propeller onto the motor shaft by engaging the propeller onto the propeller pin. 44663 3. Install the washer (or anode, for saltwater models) onto the propeller shaft then install the propeller nut. Tighten the propeller nut securely. 53442 4. Tighten the propeller nut another ¼ turn.
PAGE 33
MAINTENANCE Adjusting the Steering Cable Tension ! WARNING Neglecting to inspect, maintain, or repair your trolling motor can result in product damage or serious injury or death. Do not perform maintenance or service on your trolling motor if you are not familiar with the correct service and safety procedures. The cable tension on the X3 trolling motor is preset at the factory. With time and use, the cables may stretch slightly, requiring occasional adjustment.
PAGE 34
TROUBLESHOOTING Trolling Motor Performance Symptom Possible Cause Weak battery Loose or corroded battery connections Propeller is loose, damaged, or off‑balance Loss of power Excessive noise, vibration Refer to Maintenance. Wire gauge from the battery to the trolling motor is insufficient. Six‑gauge wire (13 mm²) is recommended. Weeds, fishing line, or debris wrapped around propeller Remove weeds, fishing line, or debris from propeller.
PAGE 35
TROUBLESHOOTING Symptom Difficulty removing propeller Possible Cause Bent propeller pin Bent armature shaft Mount bracket squeaks eng Lock pins need lubrication 31 Resolution Hold one blade and lightly tap the opposite blade with a rubber mallet. Use a putty knife on both sides of the propeller to apply equal pressure. Refer to service center. Lubricate the lock pins on the mount bracket with 2‑4‑C with PTFE.
PAGE 36
OWNER SERVICE ASSISTANCE Mercury Marine Service Offices For assistance, call, fax, or write. Please include your daytime telephone number with mail and fax correspondence. United States, Canada Telephone English ‑ (920) 929‑5040 Français ‑ (905) 636‑4751 Fax English ‑ (920) 929‑5893 Français ‑ (905) 636‑1704 Website www.mercurymarine.com Mercury Marine W6250 W. Pioneer Road P.O.