User's Manual

ManualsBrandsMotorola Solutions ManualsElectronicsPMUD2085A-VHF Portable

PRODUCT SAFETY AND RF EXPOSURE COMPLIANCE

ATTENTION!

This radio is restricted to occupational use only to satisfy FCC RF energy exposure require-

ments. Before using this product, read the RF energy awareness information and operating instruc-

tions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola

Publication part number 6804110J47) to ensure compliance with RF energy exposure limits.

For a list of Motorola-approved antennas, batteries, and other accessories, visit the following web

site which lists approved accessories: http://ap.cgiss.motorola.com/AAD/index.html.

Motorola Technology Sdn. Bhd. (Co. No. 455657-H)

Plot 2, Bayan Lepas Technoplex Industrial Park,

Mukim 12, S.W.D.,11900 Penang, Malaysia

Before using this product, read the operating instructions for safe usage contained in the

Product Safety and RF Exposure booklet enclosed with your radio.

Attaching and Removing the Antenna

To Remove Antenna

To Attach Antenna

1. Turn the antenna in a counter-clockwise

direction until it disengages from the radio.

1. Fasten the antenna to the radio by placing

the threaded end of the antenna into the

Antenna Connector.

2. Rotate the antenna clockwise until tight.

Antenna Connector

Threaded End

of Antenna

Attaching and Removing the Battery

To Remove Battery

To Attach Battery

1. Slide the battery clasp away from the radio.

2. Slide the battery downwards.

3. Pull the battery away from the radio.

1. Fit the battery slots with the grooves on the

radio.

2. Slide the battery upwards until a click is

heard.

Battery

Clasp

Grooves

Attaching and Removing the Belt Clip

To Remove Belt Clip

To Attach Belt Clip

1. Insert the end of a key between the release

tab and the back surface of the radio.

2. Lift the release tab.

3. Slide the belt clip upwards.

1. Align mounting rails of the radio with the

grooves of the belt clip.

2. Slide the belt clip downwards until it clicks

into place.

Release Tab

Mounting Grooves

Charging your Radio

1. Turn off your radio and the A/C power sup-

ply to your charger (if they are turned on).

2. Place your radio in the charger pocket.

3. Turn on the charger’s A/C power supply.

4. Charge your radio until the charger’s LED

shows a steady green light (around 2 hours

later).

5. Turn off the charger’s A/C power supply,

and remove the radio from the charger

pocket.

6. Turn on your radio; you should see all 3

bars of the Battery Level Indicator illumi-

nated.

Charger

Pocket

*6804113J11*

6815549H01-O

Text.fm Page 1 Tuesday, December 28, 2004 12:21 PM

Summary of content (2 pages)

PAGE 1
Attaching and Removing the Antenna Attaching and Removing the Battery Grooves 6815549H01-O *6804113J11* Battery Clasp Printed in Malaysia. 11/04. All Rights Reserved. © 2004 by Motorola, Inc. Motorola Technology Sdn. Bhd. (Co. No. 455657-H) Plot 2, Bayan Lepas Technoplex Industrial Park, Mukim 12, S.W.D.,11900 Penang, Malaysia ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements.
PAGE 2
Text.fm Page 2 Tuesday, December 28, 2004 12:21 PM On/Off and Volume Knob • If the radio is off, turn this knob clockwise to turn the radio on. • If the radio is on, turn this knob counter-clockwise to turn the radio off. • Turn this knob clockwise to increase the volume. • Turn this knob counter-clockwise to decrease the volume. LED Indicators LED Colour Red State Indication Illuminated Radio is transmitting. Blinking Battery voltage is low.