User's Manual
Table Of Contents
- Wireless Modem
- Table of Contents
- iM1100 Wireless Modem
- Setting Up Your Modem
- Installation Requirements
- Starting the Software Installation
- Inserting the iM1100 Wireless Modem
- Installing on Windows 2000, Windows NT, or Windows 95 and Windows 98
- Completing the Installation on Windows 2000
- 1. Before continuing to install the iM1100 wireless modem software, you must first install an upd...
- 2. Click Next when this welcome window appears:
- 3. When the User Information window appears, enter your name and your company’s name. Then click ...
- 4. When the Choose Destination Location window appears, choose a destination location or use the ...
- 5. In the Select Program Folder window, choose a destination folder, or use the default. Then cli...
- 6. To complete the installation, click Finish in the Setup Complete window.
- 1. From the Start button, choose Accessories > Communications > Network and Dial-up Connections.
- 2. From the Network and Dial-up Connections window, double click on the iM1100 connection to open...
- 3. From the Connecting iM1100 window, click Properties.
- 4. From the iM1100 window, click Configure.
- 5. When the Modem Configuration window appears, make sure that the value shown for Maximum Speed ...
- Completing the Installation on Windows 95/Windows 98
- 1. Click Next when this welcome window appears:
- 2. When the User Information window appears, enter your name and your company’s name. Then click ...
- 3. When the Choose Destination Location window appears, choose a destination location or use the ...
- 4. In the Select Program Folder window, choose a destination folder, or use the default. Then cli...
- 5. To complete the installation, click Finish in the Setup Complete window.
- 6. When the Communication Setting window appears:
- 7. If you want to change the baud rate, click the down arrow to make another selection.
- 8. Click OK. The Setup Complete window opens.
- 9. To complete the installation, click Finish in the Setup Complete window.
- Completing the Installation on Windows NT
- 1. Click Next when this welcome window appears:
- 2. When the User Information window appears, enter your name and your company’s name. Then click ...
- 3. When the Choose Destination Location window appears, choose a destination location or use the ...
- 4. In the Select Program Folder window, choose a destination folder, or use the default. Then cli...
- 5. To complete the installation, click Finish in the Setup Complete window.
- 6. An information window appears saying that Wireless Data Services software will be installed. C...
- 7. When the Install New Modem window opens, you may allow your system to search for the modem, or...
- 8. Click Next to continue to the modem selection window. In this window, you can choose a modem f...
- 9. To install a modem from a disk, click Have Disk and then Next to continue.
- 10. Type the name of the drive that contains the iM1100 wireless modem CD-ROM and click Browse to...
- 11. Select the im1100.inf file and click Open.
- 12. The Install From Disk window appears again. Click OK
- 13. The Install New Modem window appears again. Make sure that iM1100 Wireless Modem is selected ...
- 14. When the Port Selection window appears, select the COM port to which your modem is connected....
- 15. Click Finish.
- 1. Click OK.
- 2. In the Network Configuration window, select the Services tab. Within the Services tab, select ...
- 3. In the Remote Access Setup window, click Add.
- 4. In the RAS Device window, ensure the COM port for your iM1100 modem is selected. Click OK.
- 5. The Remote Access Setup window now shows the added COM port. Click Continue.
- Completing the Installation on Windows 2000
- Registering Your iM1100 Wireless Modem
- Setting or Disabling Your SIM PIN
- Using the Modem
- Getting Status Information
- SIM Card Personal Identification Number (PIN)
- Customer Support
- Accessories
- Safety and General Information
10
LOGO HERE
www.motorola.com/iden
3. In the Remote Access Setup window, click Add.
4. In the RAS Device window, ensure the COM port for your iM1100
modem is selected. Click OK.
5. The Remote Access Setup window now shows the added COM port.
Click Continue.
6. In the Network Services Selection window, click Close.
7. When the Computer Restart window appears, click Yes.
8. When the Windows banner appears during the computer restart, log on.
The installation will automatically resume. The Setup Complete window
appears.
To complete the installation:
In the Setup Complete window, choose “Yes, I want to restart my computer
now” and click Finish.
Registering Your iM1100 Wireless Modem
Your iM1100 wireless modem must register with your service providers
network before you use it for the first time.
To register your modem after installation, start the Wireless Data Services
software Status Program and connect.
NOTE
If a modem is already inserted in the same COM port as the
iM1100 modem, click “Remove” to remove it and then
click “Add”.