User's Manual
Table Of Contents
- Wireless Modem
- Table of Contents
- iM1100 Wireless Modem
- Setting Up Your Modem
- Installation Requirements
- Starting the Software Installation
- Inserting the iM1100 Wireless Modem
- Installing on Windows 2000, Windows NT, or Windows 95 and Windows 98
- Completing the Installation on Windows 2000
- 1. Before continuing to install the iM1100 wireless modem software, you must first install an upd...
- 2. Click Next when this welcome window appears:
- 3. When the User Information window appears, enter your name and your company’s name. Then click ...
- 4. When the Choose Destination Location window appears, choose a destination location or use the ...
- 5. In the Select Program Folder window, choose a destination folder, or use the default. Then cli...
- 6. To complete the installation, click Finish in the Setup Complete window.
- 1. From the Start button, choose Accessories > Communications > Network and Dial-up Connections.
- 2. From the Network and Dial-up Connections window, double click on the iM1100 connection to open...
- 3. From the Connecting iM1100 window, click Properties.
- 4. From the iM1100 window, click Configure.
- 5. When the Modem Configuration window appears, make sure that the value shown for Maximum Speed ...
- Completing the Installation on Windows 95/Windows 98
- 1. Click Next when this welcome window appears:
- 2. When the User Information window appears, enter your name and your company’s name. Then click ...
- 3. When the Choose Destination Location window appears, choose a destination location or use the ...
- 4. In the Select Program Folder window, choose a destination folder, or use the default. Then cli...
- 5. To complete the installation, click Finish in the Setup Complete window.
- 6. When the Communication Setting window appears:
- 7. If you want to change the baud rate, click the down arrow to make another selection.
- 8. Click OK. The Setup Complete window opens.
- 9. To complete the installation, click Finish in the Setup Complete window.
- Completing the Installation on Windows NT
- 1. Click Next when this welcome window appears:
- 2. When the User Information window appears, enter your name and your company’s name. Then click ...
- 3. When the Choose Destination Location window appears, choose a destination location or use the ...
- 4. In the Select Program Folder window, choose a destination folder, or use the default. Then cli...
- 5. To complete the installation, click Finish in the Setup Complete window.
- 6. An information window appears saying that Wireless Data Services software will be installed. C...
- 7. When the Install New Modem window opens, you may allow your system to search for the modem, or...
- 8. Click Next to continue to the modem selection window. In this window, you can choose a modem f...
- 9. To install a modem from a disk, click Have Disk and then Next to continue.
- 10. Type the name of the drive that contains the iM1100 wireless modem CD-ROM and click Browse to...
- 11. Select the im1100.inf file and click Open.
- 12. The Install From Disk window appears again. Click OK
- 13. The Install New Modem window appears again. Make sure that iM1100 Wireless Modem is selected ...
- 14. When the Port Selection window appears, select the COM port to which your modem is connected....
- 15. Click Finish.
- 1. Click OK.
- 2. In the Network Configuration window, select the Services tab. Within the Services tab, select ...
- 3. In the Remote Access Setup window, click Add.
- 4. In the RAS Device window, ensure the COM port for your iM1100 modem is selected. Click OK.
- 5. The Remote Access Setup window now shows the added COM port. Click Continue.
- Completing the Installation on Windows 2000
- Registering Your iM1100 Wireless Modem
- Setting or Disabling Your SIM PIN
- Using the Modem
- Getting Status Information
- SIM Card Personal Identification Number (PIN)
- Customer Support
- Accessories
- Safety and General Information
14
LOGO HERE
www.motorola.com/iden
If You Lose Connection
If you lose connection, you will see the following message:
To re-establish your connection, click Reconnect.
Running Applications over Packet Data
You can run any standard TCP/IP application during a packet data session.
NOTE
When a packet-data session is active, any software
specifically configured for use with other service providers
may be required to be reconfigured for use with your
service provider.