Motorola iDEN Digital Multi-service Data-capable Phone i305 Phone User’s Guide FINAL DRAFT @NNTN4781A@ NNTN4781A
IMPORTANT NOTICE: PLEASE READ PRIOR TO USING YOUR PHONE The SIM card provided in this kit is intended for use with the phone provided in this package. Loss of certain features will result when using a SIM card from one of the following models: i30sx, i35s, i50sx, i55sr, i58sx, i60c, i80s, i85s, i88s, i90c, i95cl series, and the i2000 series. For more information on SIM card compatibility, go to www.motorola.com/iden/support.
Contents Getting Started........................................... 1 Locating Your SIM Card .................................. 2 Battery ............................................................. 2 Activating Service ............................................ 5 Powering On .................................................... 5 Enabling Over-the-Air Security ........................ 6 Finding Your Phone Number ........................... 7 Completing Setup ............................................
Viewing Call Forwarding Settings .................. 35 Managing Memory .........................................49 Messages ................................................. 37 GPS Enabled............................................ 51 Message Notifications.................................... 37 Voice Mail ...................................................... 37 Text and Numeric Messages ......................... 38 Net Alerts .......................................................
Making International Calls ............................. 67 Setting One Touch PTT ................................. 67 Group Calls .................................................... 68 Call Timers..................................................... 69 Using Your Phone as a Modem ..................... 69 Making TTY Calls .......................................... 70 Memo ........................................................ 73 Entering Text............................................
iv
DECLARATION OF CONFORMITY Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola, Inc. Address: 8000 West Sunrise Boulevard Plantation, FL 33322 USA Phone Number: 1 (800) 453-0920 Hereby declares that the product: Product Name: i305 Model Number: H62XAH6RR1AN Conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.
vi
Getting Started antenna p volume controls Navigation key — press the arrows to scroll through menus and lists. audio jack m Push-To-Talk (PTT) button accessory connector interface Note: Throughout this User’s Guide, the option keys will be represented by A. s Send key — places phone calls. e End key — ends phone calls; returns to idle screen; in browser mode, returns to Net main menu. space key microphone back key Menu key — accesses context-sensitive menus.
Getting Started • Enable over-the-air security. Battery Locating Your SIM Card Removing the Battery Door Your SIM (Subscriber Identity Module) card is a small piece of white plastic located in the SIM card holder in the back of your phone, underneath the battery. 1 Make sure the phone is powered off. 2 Slide the release button forward until it releases the battery door.
Locating Your SIM Card 3 Remove the battery door from the back of your phone. 3 Replace the battery door and press it gently until you hear a click. Inserting the Battery Charging the Battery 1 With the phone powered off, remove the battery door. 2 Insert the top of the battery into the battery area. Press the bottom of the battery to secure it. Your phone comes with a charger. 1 Plug the charger into an electrical outlet. 2 Open the connector cover.
Getting Started 3 Plug the other end of the charger into the accessory connector. Charging Times See your battery and charger to determine the appropriate charging time. Battery Tip: To remove the charger from the accessory connector: Press the buttons on the sides of the plug. Pull the plug straight out. 4 When charging the battery for the first time, charge for 30 minutes longer than the time shown in “Charging Times”. 4 Charger Rapid Mid-Rate Extra Capacity 2 hours 4 hours Maximum Capacity 3.
Activating Service 2 Remove the battery by pushing the battery toward the antenna and lifting it out. Activating Service The first time you power on your phone, you must be in your local calling area. This activates your service. Powering On The first time you power your phone on, screen may appear asking you to update your browser information. This means you must enable security.
Getting Started As your phone connects to the network, you will see a welcome message and a connecting message. When the idle screen appears, the phone is ready to use. s 1 d Contcs S Mesg To power your phone off: 1 Press and hold p. 2 Push down the antenna.
Finding Your Phone Number Finding Your Phone Number My Info lets you view your phone number, Private ID, and other phone information: 1 2 3 4 Press m to access the main menu. Scroll to My Info. Press A under Select. Scroll to see your information: • Name — Enter your name. See “Entering Text” on page 75. • Line 1 and Line 2 — your phone numbers for phone lines 1 and 2. Each is filled in when you receive your first call on that line.
Getting Started To receive group calls made to a Talkgroup, you must join the Talkgroup. You can belong to only one Talkgroup at a time. When you join a new Talkgroup, you no longer belong to your previous Talkgroup. To join a Talkgroup: Phone Basics Any time your phone is powered on, the display provides you with information and options. status icons s 1 d 1 Press #. Then enter the Talkgroup number using the keypad.
Phone Basics Menus and Lists Main Menu Your phone’s features are arranged in menus, submenus, and lists. All your phone’s features can be accessed through the main menu. When you are using a feature, the icon for that feature appears in the upper left corner of the display. To access the items in a menu or list, scroll using the navigation key at the top of your keypad. This key lets you scroll up, down, left, or right. Holding down the appropriate part of the navigation key speeds up scrolling.
Getting Started g Memo Store a number to access later. See page 73. h Call Timers Phone usage information. See page 69. i Recent Calls Lists recent calls. See list of calls page 23. recent calls menu Call Setup menu j My Info Status Icons Status icons appear in the two rows at the top of the display. Some appear at all times. Others appear only when your phone is engaged in certain activities or when you have activated certain features.
SIM Card Security GHI J KL Call Forward — Your phone is set to forward calls. See “Call Forwarding” on page 33. To prevent unauthorized use of your phone, your SIM card is protected by a PIN that you enter each time the phone is powered on. You can change the PIN or turn off the requirement that it be entered. uvM Ringer Off — Your phone is set not to ring. See “Turning Ring Tones Off” on page 37. Entering the PIN wy x Messages — You have one or more messages. See “Messages” on page 41.
Getting Started 4 At the Enter New SIM PIN Code screen, enter the new 4- to 8-digit SIM PIN. 5 Press A under Ok. 6 At the Re-enter New SIM PIN Code screen, re-enter the new SIM PIN to confirm. 7 Press A under Ok. Turning the PIN Requirement On and Off When the SIM PIN requirement is on, you are prompted to enter your PIN each time you turn on your phone. Note: If a SIM PIN is required, your phone will not function until the SIM PIN is entered, except for making emergency calls.
SIM Card Security Inserting and Removing Your SIM Card Important: Do not touch the gold-colored areas of your SIM card. 2 Hold your SIM card as shown. Do not touch the gold-colored area. Switching SIM Cards Moving your SIM card from one phone to another moves all your Contacts information, but erases other information.
Getting Started 2 While holding down the tab near the SIM card holder, slide your SIM card out of the SIM card holder. Do not touch the gold-colored area. SIM card holder To lock the keypad: 1 From the idle screen, press m. 2 Press *. If you press a key while the keypad is locked, instructions for unlocking the keypad display briefly. To unlock the keypad: tab Note: Protect your SIM card as you would any delicate object. Store it carefully. 1 From the idle screen, press m. 2 Press *.
Making Calls Your i305 phone makes two types of calls: digital cellular phone calls and Private calls. With Private calls, you use your phone as a long-range, digital walkie-talkie. To make a phone call: 1 Enter the number you want to call. 2 Press s to place the call. 3 Press e to end the call. To make a Private call: 1 Enter the Private ID you want to call. 2 Press and hold the PTT button on the side of your phone. Begin talking after your phone emits a chirping sound. 3 Release the PTT button to listen.
Making Calls Call Icons When you make a call, call icons appear in the text area of the phone’s display. X Placing a phone call. • Use One Touch PTT to make a Private call • Use a TTY device — see “Making TTY Calls” on page 70 From the Keypad W Receiving a phone call. To enter the number you want to call, press the numbers on the keypad. Y Phone call is active. If you make a mistake: Z Phone call is on hold. • To clear a digit, press A under Delete.
Entering the Number to Call From Contacts If you have numbers stored in Contacts, you can use these numbers to make calls. For information on entering numbers into Contacts, see “Creating Entries” on page 27. Calling from the Contacts List 1 From the main menu, select Contacts. 2 Scroll to the name or number you want to call. Tip: To find Contacts entries faster, use the keypad to enter the first letter of the name. 3 Place the call now.
Making Calls If you have created a voice name in Contacts for the number you want to call, say the voice name into your phone to enter the number. See page 26 for information on voice names. 1 Press and hold t until a prompt appears telling you to say the voice name. 2 Speaking into the microphone, say the voice name assigned to the number you want to call. Your phone plays the name back to you. If you are making a Private call, press the PTT button to place the call.
Using Mute To turn speakerphone on or off: Press A under Speaker. -orPress t. Using Mute Muting calls lets you listen to incoming sound without transmitting sound. Mute is available whenever you are on an active call. To turn mute on: Press A under Mute. While mute is on, Unmute appears as a display option. To turn mute off: Press A under Unmute.
Making Calls 20
Call Alerts Receiving Call Alerts Sending a call alert lets the recipient know you want to talk to him or her on a Private call. When you receive a call alert, you must answer, queue, or clear it. You cannot receive phone calls or Private calls until you do. When you send a call alert, the recipient’s phone emits a series of beeps and displays your name or Private ID.
Call Alerts Viewing Date and Time Deleting Call Alerts To view the date and time a call alert was received: To delete a call alert from the queue: 1 2 3 4 1 From the call alert queue, scroll to the call alert you want to delete. 2 Press m. 3 Select Delete. 4 Press A under Yes to confirm. From the main menu, select Call Alert. Scroll to the call alert you want information on. Press m. Select View.
Recent Calls The recent calls list stores the numbers of the 20 most recent calls you have made and received. To view the recent calls list: 1 From the idle screen, press the down arrow on the navigation key. -orFrom the main menu, select Recent Calls. 2 Scroll through the list. If the number of a recent call is stored in Contacts, the name associated with the number appears on the recent calls list. An icon appears beside the name or number indicating the Contacts type of the number used in the call.
Recent Calls 3 To store the number as a new entry, select [New Contact]. -orTo store the number to an existing entry, select the entry. 4 With the Contacts type field highlighted, scroll left or right to display the Contacts type you want to assign the number. For information on Contacts types, see page 25. 5 If you want to add more information to the entry, follow the applicable instructions in “Creating Entries” on page 27. 6 Press A under Done.
Contacts Contacts stores up to 600 numbers or addresses. Each Contacts entry can store several numbers or addresses. • A Contacts type — Each number or address stored must be assigned a Contacts type: A Mobile phone number B Private Private ID Information stored in Contacts is saved on your SIM card. C Work1 phone number A Contacts entry contains: D Work2 phone number • A name — A name is required if your are storing more than one number or address to the entry; otherwise, it is optional.
Contacts • A Speed Dial number — When you store a phone number, it is assigned a Speed Dial number. You can accept the default Speed Dial number or change it. • A voice name — If you create a voice name for a number, you can then dial that number by saying the voice name into your phone. This icon appears P to the left of the Contacts type icon if a voice name is assigned. Note: This is an optional feature. Contact your service provider about its availability for purchase.
Creating Entries 3 With Show Prvt/Grp highlighted, press A under Select. To set Contacts to show all entries: 1 2 3 4 From the Contacts list, press m. Select Filter. Scroll to Show All. Press A under Select. Creating Entries A number or address and a Contacts type are required for all Contacts entries. Other information is optional. You may enter the information in any order by scrolling through the entry details.
Contacts Enter the number or address. For phone numbers, use the 10-digit format. For email addresses, see “Entering Text” on page 75. Tip: Press A under Browse to select a number or address from Contacts, the recent calls list, or Memo. When you are finished, press A under Ok. 6 If you want to assign more options to the number, press A under Change with the [Options] field highlighted. See “Assigning Options” on page 28.
Editing Entries To store numbers to Contacts from the idle screen: 1 Use the keypad to enter the number you want to store. 2 Press m. 3 Select Store Number. 4 To store the number as a new entry, select [New Contact]. -orTo store the number to an existing entry, select the entry. 5 With the Contacts type field highlighted, scroll left or right to display the Contacts type you want to assign the number.
Contacts Checking Capacity To see how many numbers are stored in Contacts: 1 From the Contacts list, press m. 2 Select Capacity. Creating Pauses and Waits When storing a number, you can program your phone to pause or wait between digits while dialing. A pause makes your phone pause for 3 seconds before dialing further. A wait makes your phone wait for your response before dialing further.
Accessing Contacts with GSM Phones For information about making international calls, see “Making International Calls” on page 67. Accessing Contacts with GSM Phones If you plan to use the information stored in Contacts with an i2000, i2000plus, or any other GSM phone, you must purchase CompanionPro. Go to www.motorola.com/idenupdate or your service provider’s web site for more information.
Contacts 32
Call Forwarding Call forwarding sends calls to the phone numbers you specify. You can forward all calls to one number or forward missed calls to different numbers depending on the reason you missed the call. You can forward phone lines 1 and 2 independently. Forwarding All Calls To forward all calls: 1 2 3 4 5 6 From the main menu, select Call Forward. Press A under Change. Select All Calls. Scroll to To. Press A under Change.
Call Forwarding Turning Off Call Forwarding If you don’t want all your calls forwarded, turn the feature off: 1 2 3 4 5 6 7 From the main menu, select Call Forward. Press A under Change. Select All Calls. Scroll to To. Press A under Change. Scroll to Off. Press A under Select. All your calls are now sent to your phone. Calls you miss are forwarded according to the options set for missed calls. By default, missed calls are forwarded to voice mail.
Viewing Call Forwarding Settings Press A under Search. Select Contacts, Recent Calls, or Memo. Select the number you want to enter. 8 Press A under Ok. 9 Repeat step 4 through step 8 for No Answer and If Unreachable. When you are finished, press A under Back. Viewing Call Forwarding Settings 1 From the main menu, select Call Forward. 2 With To highlighted, press m. 3 Select Retrieve Status.
Call Forwarding 36
Ring Tones Using the Vibrate Feature To set the ring tone your phone makes when you receive phone calls, message notifications, or call alerts: If your phone includes a vibrate feature, you can set your phone to vibrate when you receive phone calls, Private calls and group calls, messages notifications, or call alerts. 1 From the main menu, select Ring Tones. 2 Make sure VibeAll or SilentAll is set to Off. 3 Scroll through the list of ring tones to the one you want to assign.
Ring Tones Never Ring 1 From the main menu, select Ring Tones > SilentAll. 2 Scroll left or right to set SilentAll to On. Always Vibrate Instead of Ringing If your phone includes a vibrate feature: 1 From the main menu, select Ring Tones > VibeAll. 2 Scroll left or right to set VibeAll to On. Tip: Pressing the volume controls to turn down the volume as far as possible sets VibeAll to On.
Assigning Ring Tones to Contacts Assigning Ring Tones to Contacts You can set the ring tone your phone makes when you receive phone calls or call alerts from someone you have stored in Contacts. 1 From the main menu, select Ring Tones. 2 Make sure VibeAll or SilentAll is set to Off. 3 Scroll through the list of ring tones to the one you want to assign. Highlighting a ring tone lets you hear it. 4 Press A under Assign. 5 Select A Contact. 6 Scroll to the Contacts entry you want to assign the ring tone to.
Ring Tones Note: Ring tones are stored in your phone using the same memory space used to store voice records (see “Voice Records” on page 61), Deleting voice records frees memory space for ring tones. Deleting Custom Ring Tones To delete a custom ring tone: 1 2 3 4 5 6 44 From the main menu, select Ring Tones. Make sure VibeAll or SilentAll is set to Off. Scroll to the ring tone you want to delete. Press m. Select Delete. Press A under Yes to confirm.
Messages If you are on a call when you receive a message, your phone may sound a notification tone during the call or after you end the call, depending on how you set your notification options. To access your voice mail messages, text and numeric messages, Net alerts, and any other types of messages you are able to receive, go to the message center: Setting Notification Options 1 Press A under Mesg.
Messages When you receive a voice mail message, New Voice Mail Message appears on the display. To call your service provider’s voice mail system and listen to the message: Press A under Call. To dismiss the message notification: Press A under Exit. This icon y appears on the display, reminding you that you have a new message. Sending Unanswered Calls to Voice Mail To send a phone call to voice mail instead of answering it: Press e. -orPress A under No.
Net Alerts Press A under Back. This icon w appears on the display, reminding you that you have a new message. Reading from the Message Center 1 2 3 4 From the message center, select Text Msgs. Scroll to the message you want to read. Press A under Read. If the message fills more than one screen, scroll to read it. 5 To keep the message, scroll to the end of the message and press A under Save. -orTo delete the message, press A under Delete.
Messages 40
Mobile Originated Text Messaging With mobile originated text messaging, you can send and receive short text messages to and from other iDEN phones. Messages you receive appear on your phone’s display and in the text message inbox. You access these messages through the message center. See “Messages” on page 41. Note: This feature may not be offered by your service provider.
Mobile Originated Text Messaging Reading Messages From the Message Center 1 From the main menu, select Message > Text Inbox. 2 Scroll to the message you want to read. 3 Press A under Read. 4 If the message fills more than one screen, scroll to read it. 5 To keep the message, press A under Save. -orTo delete the message, press A under Delete. Tip: To see more choices, including replying to the message, press m. Your text inbox holds up to 16 messages. Each message can be up to 160 characters long.
Creating and Sending Messages With the Send As field highlighted, press A under Change. Scroll to the message type you want. Press A under Select. 4 Select Compose SMS. The message is automatically addressed to the phone number you chose. 5 Follow step 4 through step 8 of “Creating and Sending Messages” on page 46. 8 To send the message: Press s. Press A under Yes.
Mobile Originated Text Messaging Enter text. See “Entering Text” on page 75. -orTo choose from pre-installed notes: Press A under Browse. Scroll to the note you want. Press A under Select. 3 Press A under Store. Tip: For more options, including sending the quick note, press m. 3 Follow step 3 through step 7 in “Creating and Sending Messages” on page 46. 4 Scroll to Save As Draft. Using the Outbox Messages you have sent are stored in the outbox.
Managing Memory 3 Press m. 4 Select Re-send. 5 Press A under Yes to confirm. 3 Press m. 4 Scroll to Lock to lock the message. -or- Deleting Sent Messages 5 Press A under Select. To delete a sent message: Managing Memory 1 From the main menu, select Messages > Text Outbox. 2 Scroll to the message you want to delete. 3 Press m. 4 Select Delete. 5 Press A under Yes to confirm. To delete all unlocked sent messages: 1 From the main menu, select Messages > Text Outbox. 2 Press m. 3 Select Delete All.
Mobile Originated Text Messaging 2 Press m. 3 Select Memory Meter.
GPS Enabled Your phone’s GPS Enabled feature uses information from Global Positioning System (GPS) satellites orbiting the Earth to determine the approximate geographical location of your phone, expressed as latitude and longitude. The availability and accuracy of this location information (and the amount of time that it takes to calculate it) will vary depending on the environment in which you are using the GPS feature.
GPS Enabled • When your GPS antenna is covered (for example, by your hand or other object) or facing the ground • In temperature extremes outside the operating limits of your phone Walking or driving very slowly may also substantially reduce GPS performance. Even where location information can be calculated in such situations, it may take much longer to do so, and your location estimate may not be as accurate.
Viewing Your Approximate Location GPS satellite signals and network assist data, it may take 30 seconds or more to determine the approximate location. This time will increase where there is reduced access to satellite signals. When your approximate location is determined, it is made available to the appropriate emergency response center. In some cases, your local 911 emergency response center may not be equipped to receive GPS location information.
GPS Enabled • The number of satellites used to calculate the location. In general, more satellites make for better accuracy. To calculate your location again: Press A under Rfrsh. It may take your phone several minutes to complete the process of determining your location. During this time, a message usually appears on your phone’s display saying your phone is scanning for satellites. For tips on getting the best location calculation, see “Enhancing GPS Performance” on page 54.
Updating Satellite Almanac Data • Stay in the open. The GPS feature works best where there is nothing between your phone and a large amount of open sky. If possible, go outside, away from tall buildings and foliage. While performance in a building is improved by moving closer to windows, glass with certain sun shielding films may block satellite signals. • Hold your phone to enhance reception.
GPS Enabled The United States government maintains an almanac of data about where GPS satellites are as they orbit the Earth. This information is available to your phone. Keeping your satellite almanac up to date helps your phone determine your location more quickly. The almanac contains information about the location of satellites, their operational status, and other satellite information. Keeping this information updated enhances the performance of your GPS feature.
Using GPS with Map Software When you receive your phone, the GPS security feature is turned off, so you do not have to enter a GPS PIN to access your GPS privacy options. If you turn this feature on, you will be required to enter a GPS PIN to access your GPS privacy options. To turn the GPS Enabled security feature on or off: 1 From the main menu, select Settings > Security > GPS PIN. 2 Scroll to On or Off. 3 Press A under Select. 4 Enter the current GPS PIN.
GPS Enabled Software Compatibility Your phone sends location information to your laptop or other device using the standard National Marine Electronics Association (NMEA) format. Your phone supports output messages in NMEA-0183 format and supports the following NMEA-0183 sentences: GGA, GLL, GSA, GSV, RMC, and VTG. 2 With the phone’s display facing up, insert the data cable’s connector into the accessory connector, until you hear a click.
Using GPS with Map Software To set your phone to send location information to your laptop or other device: 1 From the main menu, select GPS > Interface. 2 With NMEA OUT highlighted, press A under Change. 3 Scroll to On. 4 Press A under Select. Your phone is now sending location data to your laptop or other device. To stop your phone from sending location data to your laptop or other device: Set NMEA OUT to Off. Each time you power your phone on, NMEA OUT is automatically set to Off.
GPS Enabled 60
Voice Records Note: This is an optional feature. Contact your service provider about its availability for purchase. A voice record is a recording you make with your phone and can play back. You can record notes to yourself or phone calls. Your phone can store up to 20 voice records, with a total time of 3 minutes or more, depending on available memory. 5 Press A under Select. Say the message you want to add into the microphone. 6 When you are finished recording, press A under Stop.
Voice Records Labelling Voice Records 4 Press A under Yes to confirm. When you create a voice record, it is labeled with the time and date it was recorded. You can then rename it with a custom label. Locking Voice Records 1 2 3 4 5 From the main menu, select VoiceRecd. Scroll to the voice record you want to label. Press m. Select Label. Enter the label you want to assign. See “Entering Text” on page 75. 6 Press A under Ok.
Managing Memory 2 3 4 5 Press m. Select Memory. Press A under Delete. Press A under Yes to confirm. Note: Voice records are stored in your phone using the same memory space used to store ring tones (see “Ring Tones” on page 37), Deleting ring tones frees memory space for voice records.
Voice Records 64
Advanced Calling Features Call Waiting Call Waiting lets you receive a second call while on an active call. Call Waiting is always available, unless you turn it off for a specific call. Switching Between Calls When you accept a second call, the display shows the name or number of each call, with an icon indicating which call is active: Y Phone call is active. Z Phone call is on hold.
Advanced Calling Features To turn off Call Waiting for the next call you make or receive: To end the second call and make the call on hold active again: 1 From the main menu, select Settings > Phone Calls > Call Waiting. 2 Press A under Change. 3 Scroll to Off. 4 Press A under Select. To make the call on hold active and put the active call on hold: Call Waiting is turned back on when you end the call. Call Hold Press e. Press A under Switch.
Creating Pauses and Waits While Dialing 9 Press A under Select. Both calls are now active and appear on the display. Creating Pauses and Waits While Dialing You can enter a pause or wait while dialing a number. For more information on pauses and waits, see “Creating Pauses and Waits” on page 30. To create a pause while dialing a phone number: 1 From the keypad, enter the digits you want to occur before the pause. 2 Press m. 3 Select Insert Pause. 4 Enter the digits you want to occur after the pause.
Advanced Calling Features To set your phone to call a Private ID you choose: 1 From the main menu, select Settings > 2-Way Radio > One Touch PTT > Assigned Number. 2 To enter the Private ID you want your phone to call every time you press the PTT button: Enter the number using your keypad. -orPress A under Search. Select Contacts, Recent Calls, or Memo. Select the number you want to enter. Tip: If you are entering a Talkgroup number, enter # before the number.
Call Timers 3 Scroll to On if you don’t want to hear group calls to your Talkgroup. -orScroll to Off if you want to hear group calls to your Talkgroup. 4 Press A under Select. Call Timers Call timers measure the duration of your phone calls, Private or group calls, and circuit data use, as well as the number of Kilobytes sent and received by your phone: • Last Call — displays the duration of your most recent phone call. • Phone Reset — keeps a running total of your phone call minutes, until you reset it.
Advanced Calling Features 1 Open the connector cover. 3 Insert the data plug into the COM port of the other device. connector cover When used as a modem, your phone has these data transfer modes: • Circuit data — used for sending and receiving faxes and for transferring large files • Packet data — used for small file transfers such as email 2 With the phone’s display facing up, insert a data cable’s connector into the accessory connector, until you hear a click.
Making TTY Calls 3 Use your phone to enter phone numbers and make calls. When you make a TTY call, these icons appear on the phone’s display: N Phone call is active. O Phone call is on hold. TTY device features such as Turbo-Code, High-Speed, and Interruption are not supported by your phone. These features must be turned off or disabled to use your TTY device with your phone.
Advanced Calling Features Important: When you are using HCO, the sound coming from your phone speaker may be uncomfortably loud. Use caution when putting the phone to your ear. (For information on setting the volume of your phone speaker, see “Setting the Volume” on page 79.) Changing the TTY Baud Rate By default, your phone’s TTY baud rate is set to 45.45, the baud rate required for TTY calls within the U.S. To make calls outside the U.S., set your TTY baud rate to 50.0.
Memo Memo lets you store a number, make a call to that number, and save it to Contacts. To create a memo: 1 From the main menu, select Memo. 2 Enter the number using your keypad. 3 Press A under Store. To view the memo later: 1 From the main menu, select Memo. To delete the memo: 1 From the main menu, select Memo. 2 Press and hold A under Delete. 3 Press A under Store. To store the memo number to Contacts: 1 2 3 4 From the main menu, select Memo. Press m. Press A under Select.
Memo 74
Entering Text You can enter text into your phone using the traditional method of pressing a key several times for each character, or by pressing a key once for each letter while words likely to be the one you want are chosen from a database. You can also enter symbols and numbers into a text field. In screens that require you to enter text, you see the following icons near the top right corner. These icons tell you which text input mode you are using: l Alpha — Press a key several times for each character.
Entering Text 2 Type a word by pressing one key for each letter. To change the language of the database: The displayed word may change as you type it. Do not try to correct the word as you go. Type to the end of the word before editing. 1 At a screen that requires you to enter text, press m. 2 Select Languages. 3 Scroll to the language you want for your database. 4 Press A under Select.
Using Numeric Mode These icons appear in the top row of your display: m Shift is on. n Caps lock is on. When neither of these icons appear, letters typed are lowercase. A row of symbols appears along the bottom of your phone’s display. Scroll right to view the complete row. 2 Scroll left or right to choose the symbol you want to enter. 3 Press A under Select. Note: Your phone automatically makes the first letter of a sentence uppercase. Punctuation Press 1 or 0 to insert punctuation.
Entering Text 78
Customizing Your Phone volume of the phone’s ring when you get a call on that line. Setting the Volume See “Volume Features” on page 81. To set the volume of the sound coming from the phone’s earpiece or speaker: Setting Your Phone to Not Ring 1 From the main menu, select Settings > Volume. 2 Scroll to Earpiece to set the earpiece volume. -orScroll to Speaker to set the speaker volume. 3 Press A under Change. 4 To select the volume: Scroll left or right. -orPress the volume controls.
Customizing Your Phone If your phone does not include a vibrate feature, you can still set your phone to make no sound. Scroll to Silent in step 3. Seeing the Display Better To set the contrast of the display: 1 From the main menu, select Settings > Display/Info > Contrast. 2 Press A under Change. 3 Scroll left or right to set the contrast. 4 Press A under Ok.
Using Settings • Auto Redial — sets your phone to automatically redial calls you make when the system is busy. • Call Waiting — See “Call Waiting” on page 65. • Auto Ans — sets your phone to automatically answer an incoming call after a specified number of rings. When this feature is on, the phone answers by connecting you to the caller; it does not send the call to voice mail, unless you are out of coverage or on the line. • Minute Beep — causes a beep to sound every minute of an active call.
Customizing Your Phone • Phone Lock — turns on a feature that locks your phone, either immediately or automatically after a set period of inactivity. An unlock code is required to enable this feature, to unlock the phone, and to set a new Unlock code. Contact your service provider for your default unlock code. • Keypad Lock — locks the phone’s keypad, either immediately or automatically after a set period of inactivity.
Understanding Status Messages Status Messages Message Description System Busy The system is experiencing heavy traffic. Please try again later. You may receive status messages under certain conditions. Before contacting Customer Care, note the message, numeric code, and the conditions under which it appeared. The following table lists and describes the status messages. Please Try Again An error occurred. Please try again. Self Check Error + Number Code A fault was detected with your phone.
Understanding Status Messages Status Messages Message Description Enter SIM PIN Please enter your 4- to 8- digit SIM PIN code. Enter Unlock Code Auto Phone Lock is activated. Enter you unlock code. New Browser Message Memory Full! Warns of low memory for Net Alerts. Scanning for Satellites Searching for GPS satellites. Unable to Locate Sats Could not find GPS satellites. Technical Error A problem occurred in your phone’s GPS circuitry.
Safety and General Information IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION. READ THIS INFORMATION BEFORE USING YOUR INTEGRATED MULTI-SERVICE PORTABLE RADIO. RF Operational Characteristics Your radio product contains a radio frequency transmitter to convey the information you wish to send as well as occasional automatic signals used to sustain connection to the wireless network, and a receiver which enables you to receive communication and connection information from the network.
Safety and General Information Phone Operation When placing or receiving a phone call, hold your radio product as you would a wireline telephone. Speak directly into the microphone. • Phone or Two-way radio mode: one inch (2.5 cm) • Data operation using any data feature with or without an accessory cable: one inch (2.
Portable Radio Product Operation and EME Exposure ALL MODELS WITH FCC ID AZ489FT5822 MEET THE GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population.
Safety and General Information Electro Magnetic Interference/Compatibility Note: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed or otherwise configured for electromagnetic compatibility. Medical Devices Pacemakers The Advanced Medical Technology Association (AdvaMed) recommends that a minimum separation of 6 inches (15 cm) be maintained between a handheld wireless radio product and a pacemaker.
Operational Warnings Other Medical Devices Operational Warnings If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information. For Vehicles with an Air Bag Use While Driving Check the laws and regulations on the use of radio products in the area where you drive. Always obey them.
Safety and General Information other area where you would normally be advised to turn off your vehicle engine. Areas with potentially explosive atmospheres are often but not always posted. Blasting Caps and Areas To avoid possible interference with blasting operations, turn off your radio product when you are near electrical blasting caps, in a blasting area, or in areas posted: “Turn off two-way radio”. Obey all signs and instructions.
Accessory Safety Information Clean the external surfaces of the radio product with a damp cloth, using a mild solution of dishwashing detergent and water. Some household cleaners may contain chemicals that could seriously damage the radio product. Avoid the use of any petroleum-based solvent cleaners. Also, avoid applying liquids directly on the radio product. Accessory Safety Information Important: Save these accessory safety instructions.
Safety and General Information • The cord size is 18AWG for lengths up to 100 feet and 16AWG for lengths up to 150 feet. • Do not operate any battery charger if it has received a sharp blow, has been dropped, or has been damaged in any way; take it to a qualified service technician. • Do not disassemble a battery charger; take it to a qualified service technician when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
MOTOROLA LIMITED WARRANTY Note: FOR IDEN SUBSCRIBER PRODUCTS, ACCESSORIES AND SOFTWARE PURCHASED IN THE UNITED STATES OR CANADA What Does this Warranty Cover? Subject to the exclusions contained below, Motorola, Inc.
MOTOROLA LIMITED WARRANTY What is not covered? (Exclusions) Normal Wear and Tear. Periodic maintenance, repair and replacement of parts due to normal wear and tear are excluded from coverage. Batteries. Only batteries whose fully charged capacity falls below 80% of their rated capacity and batteries that leak are covered by this limited warranty. Abuse & Misuse.
Software NOT Embodied in Physical Media. Software that is not embodied in physical media (e.g. software that is downloaded from the internet), is provided "as is" and without warranty. Who is covered? This warranty extends only to the first consumer purchaser, and is not transferable. What will Motorola Do? Motorola, at its option, will at no charge repair, replace or refund the purchase price of any Products, Accessories or Software that does not conform to this warranty.
MOTOROLA LIMITED WARRANTY BUSINESS, LOSS OF INFORMATION OR DATA, SOFTWARE OR APPLICATIONS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS, ACCESSORIES OR SOFTWARE TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW. Some states and jurisdictions do not allow the limitation or exclusion of incidental or consequential damages, or limitation on the length of an implied warranty, so the above limitations or exclusions may not apply to you.
Limited Warranty Motorola Communication Products (International) Note: This Warranty applies in Singapore and the Philippines. I.
Limited Warranty Motorola Communication Products (International) Product with any ancillary equipment, and all such equipment if expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole, or any portion of the system not produced by MOTOROLA, under this warranty. II.
d. e. f. g. h. i. operation, maintenance, installation, alteration, modification, or adjustment. Breakage or damage to antennas unless caused directly by defects in material workmanship. A Product subjected to unauthorized Product modifications, disassemblies or repairs (including, without limitation, the audition to the Product of non-MOTOROLA supplied equipment). Product which has had the serial number removed or made illegible. Rechargeable batteries if: 1.
Limited Warranty Motorola Communication Products (International) MOTOROLA’S opinion be likely to become, the subject of a claim of infringement of a patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return.
Patent and Trademark Information MOTOROLA, the Stylized M Logo and all other trademarks indicated as such herein are trademarks of Motorola, Inc. ® Reg. U.S. Pat. & Tm. Off. © 2003 Motorola, Inc. All rights reserved. Microsoft and Microsoft Internet Explorer are registered trademarks of Microsoft Corporation. T9 is a trademark owned by Tegic Communications. T9® Text Input Patent and Trademark Information distribute or reproduce the copyrighted software.
Patent and Trademark Information 102
Index Numerics 2-way radio 81 see also Private calls, group calls, and call alerts 3-way calling 66 A Accessories 14 safety 91 Alpha mode 75 B Backlight 80 Battery 2 care 5 charging 3, 4 cover 2 inserting 3 safety 90 Baud rate 82 C Call alerts 21 deleting 22 queue 21 receiving 21 responding 21, 22 sending 21 sorting 22 viewing 21 Call forwarding 33 all calls 33 missed calls 34 off 34 Call Hold 66 Call Timers 69 Call Waiting 65 off 65 Calls 3-way 66 answering automatically 81 answering with any key 80 em
Index showing only Private IDs 26 SIM card 25 storing fast 28 storing from idle screen 29 storing from Memo 28, 73 storing from recent calls 23, 28 type 23, 25 viewing 26 voice name 28 D Display backlight 80 contrast 80 options 8 screen 8 E Email 25, 28, 70 receiving 39 sending 39 Emergency calls 19 End key 1 104 F I Faxes receiving 70 sending 70 Icons calls 16 Contacts 25 main menu 9 mobile originated text messaging 48 Recent calls 23 status 10 text entry 75 Idle screen 8 storing to Contacts 29 Inte
M Memo 73 calling from 73 creating 73 editing 73 storing to Contacts 28, 73 viewing 73 Memory mobile originated text messaging 49 ring tones 43 voice records 62 Menu key 1, 9 Menus 9 context-sensitive 1, 9 main menu 9 Message notifications 37 setting options 37 Messages 37 see also mobile originated text messaging reading 39 receiving 37 text and numeric 38 Mobile originated text messaging 45 creating messages 46 deleting 49 drafts 48 icons 48 memory 49 outbox 48 quick notes 47 reading messages 46 receivin
Index storing to Contacts 23, 28 viewing 23 Redialing 17, 81 Removing the Back Cover 2 Ring tones 25, 41 deleting 44 downloading 43 memory 43 off 41 setting 41 setting in Contacts 27, 43 silent 41, 42 vibrate 41, 42 viewing assigned 43 Ringer 79 see also Ring tones off 79 S Safety 85 accessory 91 battery 90 driving 109 electromagnetic interference 88 106 medical devices 88 radio frequency 85 Security 81 Send key 1 Service provider 14 Service, activating 5 Settings 80 resetting 82 SIM card 11, 13 Contacts
creating 28 Voice records 61 creating 61 deleting 62 labelling 62 locking 62 memory 62 playing 61 Volume, setting 79, 81 W Waits dialing 67 storing 30 Warranty 97 Word mode 75 107
Index 108
Driving Safety Tips “Safety is your most important call!” Your Motorola wireless telephone gives you the powerful ability to communicate by voice — almost anywhere, anytime, wherever wireless phone service is available and safe conditions allow. But an important responsibility accompanies that benefits of wireless phones, one that every user must uphold. When driving a car, driving is your first responsibility.
Driving Safety Tips • Use your wireless phone to call for help. Dial 9-1-1 or other local emergency number in the case of fire, traffic accident or medical emergencies. • Use your wireless phone to help others in emergencies. If you see an auto accident, crime in progress or other serious emergency where lives are in danger, call 9-1-1 or other local emergency number, as you would want others to do for you. • Call roadside assistance or a special non-emergency wireless assistance number when necessary.
