APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 INSTRUCTION MANUAL A preliminary draft copy of the Users Manual follows. RF exposure information is located in section 1.3.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 D15 – Developer Guide – 1st draft 1. Introduction Product description The D15 model Main application SAR Requirements. 2. Installation Mechanical description Connections 3. Pin description & main Functionality Pin description of connectors per model Different communication & application 4. Modes of Operation On/Off process include time diagram Voice connection Full flow control data call Soft GSM Operation 5.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 1. Introduction 1.1 Product Specification – See in Appendix bellow. To add a note thal all the Data/Audio/SIM signals are compatible with D10 30 pin FC User Device D10 User Device D15 3 lines removed from each side 36 pin FC 1.2 D15 Models: • D15 DV (DV= Data & Voice) Standard.
APPLICANT: MOTOROLA, INC.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 1.3 SAR Requirements User Operation Do not operate your telephone when a person is within 8 inches (20 centimeters) of the antenna. A person or object within 8 inches (20 centimeters) of the antenna could impair call quality and may cause the phone to operate at a higher power level than necessary and expose that person to RF energy in excess of that established by the FCC RF Exposure Guidelines.
APPLICANT: MOTOROLA, INC. 2. Installation FCC ID: IHDT6AC1 – See details in PRD.
APPLICANT: MOTOROLA, INC.
APPLICANT: MOTOROLA, INC.
APPLICANT: MOTOROLA, INC.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 3. Pin description & main Functionality 3.1 Standard model & Slim model The available functionality in these models are the follow: Data & Voice (D10 Replacement & Slim) - Connections General Data purposes DSC bus Power supplies Main PWR Main Process. EXT_SIM DSC Audio Data port Uart #1 D15 User logic RS232 port 3.1.1 Function available in the user connector – 36 pin ZIF • VCC input. • Full RS232 - 9 pins. • External SIM connections.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 2. The TS line is used to turn On the units by any transaction from Low to high in this pin. 3.1.2 Connector pin out Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Function TX_EN N.U. N.U. TXD RXD DTR DCD RTS CTS DSR RI Manual_Test Audio In On/Off + Audio Out N.U.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 3.2 D15 with GPS The available functionality in this models are the follow: Data & Voice + GPS model - Connections GPS purposes GPS Process. General Data purposes DSC bus Power supplies GPS (M12) GPS Ant PWR Main PWR User logic 3V 1PPS RX Diff Reg Main Process. EXT_SIM DSC Audio Data port Uart #1 D15 RS232 port 3.2.1 Function available in the user connector – 36 pin ZIF • VCC input. • Full RS232 - 9 pins. • External SIM connections. • DSC bus.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 RTCM, Antenna power Note: 1. The Audio Out line is used to send out the detected audio and as a toggle On/Off pin. 2. The TS line is used to turn On the units by any transaction from Low to high in this pin. 3. The GPS is mounted on top of theD15 and receive power from the D15 but it is a stand-alone unit. The GPS is working from 3V and the RXD/TXD lines are working in 3V levels as well. The GPS receiver used is M12 (Motorola). 3.2.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 3.3 D15 in DIN Models (Vertical & Horizontal) The available functionality in this models are the follow: Data & Voice in DIN configuration- Connections EXT_SIM DSC Power supplies Audio User logic Data port Main PWR White Cap Uart #1 IRDA IRDA (future feature) D15 General Data purposes DSC bus 3.3.1 Function available in the user connector – 28 R/A Male header (vertical model) 28 pin Female sockets, receptacle (Horizontal model) • VCC input.
APPLICANT: MOTOROLA, INC. 3.3.2 Connector pin out Pin # 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Function EXT. B+ (3.5 EXT. B+ (3.5 SIM I/O *SIM_RST SIM VCC (3/5 SIM PD DTR TS Manual Test IRDA / RS232 GND GND RI DCD FCC ID: IHDT6AC1 Pin # 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. to 6V) to 6V) Volt) Select Function NU TX_EN Analog GND Audio Out+ On/Off Audio In (Mic) DSC_EN DSR Down Link Up Link SIM_CLK TXD_U1 RXD_U1 CTS RTS Note: 1.
APPLICANT: MOTOROLA, INC.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 4.1.2 Turn On the unit using the TS pin. The main used of the TS line is for units connected to a mobile device in witch the current consuption is not the main consern. The TS line is used to turn On the unit. This line can’t turn Off the unit. When this line is rised up it will turn On the unit. This line is used for example to turn On the unit when power is connected to the unit. (Like Ignition line in a car kit).
APPLICANT: MOTOROLA, INC.
APPLICANT: MOTOROLA, INC. 4.2 FCC ID: IHDT6AC1 Data connectivity. To clarify the Data connectivity and the direction of the signal see the follow diagram: All the signals in the user connector are 0 to 5V. When the control lines (RTS, DTR, DCD, CTS, DSR, RI) active is low (0V) and unactive is high (5V).
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 User connector 28 pin DIN 25 EXT_TXD TXD 7 EXT_DTR DTR 28 EXT_RTS RTS 26 EXT_RXD RXD 14 EXT_DCD DCD 27 EXT_CTS CTS 21 EXT_DSR 13 EXT_RI D15 processor DSR RI There are two modes to use the Data - - port: SoftGSM mode. This mode is for computer aplication in witch an application SW “SoftGSM” is use. This alowed the D15 to work with V42.bis (data compression), transfer fax and SMS. RS232 full flow control.
APPLICANT: MOTOROLA, INC. 4.2.1 FCC ID: IHDT6AC1 Using the SoftGSM. 4.2.1.1 SoftGSM Selection The selection of SoftGSM is done by Hardware in the user application. In order to switch to this mode the user need to connect pulldown resistors of 22Kohm in the Downlink line (pin no’23 in the zif connector or pin no’22 in the 28 pin) and the DCS_EN line (pin no’22 in the zif connector or pin no’20 in the 28 pin). In this mode the necessary lines are: TXD, RXD.
APPLICANT: MOTOROLA, INC.
APPLICANT: MOTOROLA, INC.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 Sending / Receiving SMS PDU mode in SoftGsm 4.2.1.4 Sending / Receiving SMS block mode.
APPLICANT: MOTOROLA, INC. 4.2.2 FCC ID: IHDT6AC1 Using RS232. 4.2.2.1 RS232 Selection The RS232 is the default setting in the D15 and no HW selection is needed. The RS232 can use 3 different modes of setting to the DTE device: HW (Hardware) flow control – all RS232 lines are used (DTR, DSR, RTS, CTS, TXD, RXD, DCD, RI, GND). None flow control – DTR, DSR, TXD, RXD, DCD, RI, GND are required. Xon / Xoff flow control – DTR, DSR, TXD, RXD, DCD, RI, GND are required. 4.2.2.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 4.2.2.3 File transfer in RS232 mode. To Transfer a file in RS232 you need to: 1. connect the relevant lines depend on the mode to a comm port of the computer.(the levels should be converted to RS232 or use a EV board or equivqlent). 2. Run Hyper terminal application or equivalent in the computer. (in the final application it will be the user program). 3. Select the flow control / Comm and baud rate. 4. Select the activity send/Receive file/Fax/SMS .
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 The activity of the required lines and timming for file transfer using RS232 HW flow control can be seen in the following plot: Sending a file in HW flow control.
APPLICANT: MOTOROLA, INC.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 Sending a SMS in PDU mode – HW flow control.
APPLICANT: MOTOROLA, INC.
APPLICANT: MOTOROLA, INC.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 Receiving a SMS in PDU mode – HW flow control.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 4.1.2.1 Transfer files using Xon/Xoff setting.
APPLICANT: MOTOROLA, INC.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 4.1.2.2 Transfer files using none setting.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 Receiving a file in none mode 4.1.2.2 Sending/ Receiving SMS block mode.
APPLICANT: MOTOROLA, INC. 4.3 FCC ID: IHDT6AC1 Voice connectivity. The D15 is an OEM Data & Voice module. The voice connectivity can be done in two main channels – analoge voice, Digital voice. 4.3.1 Digital voice: The Digital voice is done using the Motorola DCS bus. This bus is an Motorola Propriretry bus and details can be received after an agreement.
APPLICANT: MOTOROLA, INC. 4.3.2 FCC ID: IHDT6AC1 Analog Audio. The D15 is driving out the analog audio detected by the radio. The D15 is not including any audio drivers. The user have to include the audio drivers in is application. An example for audio drivers can be seen in the EV board appendix ??. The D15 can provide the analog audio in two ways: - Analog audio to by drived to an Headset – Default. - Analog audio with Echo canceller activated – for Hands free applications.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 D15 SPKR 12V MIC A1 Audio out Hands Free Selection Headset Audio In A2 Hands Free Selection VCC REF VCC Analog GND Hands Free Selection via ATS96 command. Vref (for Audio amp) The requirements from the drivers and audio devices are the follow: Microphone impedance: S/N ratio Gain from headset to D15 (A2) Frequency response (including microphone) D15 input impedance TX Distortion Typical 700Ω Minimum 35dB 45 – 49 dB -11 to +1 dB 300 to 3400Hz.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 The Audio route for the different devices is descrived in the following table: Configuration Setup and aAudio Routing in D15 1. HF Refer to External Speaker & Microphone connected. 2. DHFA refers to External Car kit. 3. Correct setup are in bold letters.
APPLICANT: MOTOROLA, INC. 5. FCC ID: IHDT6AC1 Design Consideration 5.1 Power supply considerations. Current requirements in each mode. 5.2 Audio considerations.to refer to EV board chepter in appendix.Car Kit connectionsl. 5.3 Data port considerations & Levels. 5.4 SIM card considarations. 5.5 ESD considerations. 5.6 Antenna 5.7 Software 5.8 Mechanical 5.1 Power supply consideration. 5.1.1 Power Supply losses. The D15 is specified to operate from 3.0V to 6.0V.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 modes. Mode Current consumption D15 with no accessory when no call is in process <11mA Typical 10mA. D15 with no accessory but TS or RTS are ON < 50mA. D15 during searching time <180mA typical average 80mA. D15 with DSC bus accessory(like Handset) when no call is in process Typical 40 mA. D15 during a call in maximum power level <1.5A Peak, Average 300mA. D15 during a call in GSM power level #10 (for Example) <0.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 5.1.3 How / When to make the unit to wakeup. If the D15 will have no accessories and the unit is camped the D15 will go to a "sleep mode" (current save mode). During this period of time the RS232 is not responding to any command from the DTE device.In order to make the unit to wake up when the DTE will like to communicate with the radio the user have two options: 1. Activate the RTS During all the DTE/DCE dialog. (Internaly the TS line will be activated).
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 5.2.1 Digital audio. In case of digital audio channel a DCS drives is in used. The consideration that should be taken in this case is to be aware of the present of the hook switch. The hook switch will destinguish if the handset is In/Out of use. There are two DSC bus accessories for audio defined for the D15: External Handset. DHFA - Car Kit for Hands Free. 5.2.2 Analog Audio without Handsfree.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 The main problem causing the Buzz is drops in the Ground line because the peak current during TX mode. In order to minimize the Buzz the following acts should be done: - Use short Flat cable. - Connect the analog ground from the D15 to all the analog circuits in the customer application without connecting them to the power supply ground. - all the capacitors to ground in the audio circuits should be connected to the analog ground.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 5.3 Data port considerations. 5.3.1 Data levels. The D15 data lines are operating in 0 to 5V logic. All the In/Out signals are bufferd by an MC74VHCT244 buffer. DTR, DSR, RTS, CTS, DCD lines are "1" (active) in 0V and "0" (inactive) in 5V. The signal treshoulds are: Vih 2.0V min. Vil 0.8V max. Voh 4.4V min. @ 50uA or 3.8V min. @ 8mA. Vol 0.1 max. @ 50uA or 0.44V @ 8mA. 5.3.
APPLICANT: MOTOROLA, INC. FCC ID: IHDT6AC1 5.4 SIM lines consideration. The SIM card can be used in 3 different ways: Internaly in the D15, Externaly by connecting a socket in the customer application and remotly via the DCS bus. In case of externaly connection the customer concern should be for Full Type Approval that may require submittion for testing in case that the SIM lines will be longer than 10cm. This Paragraph should be completed. 5.5 ESD consideration - TBD 5.
APPLICANT: MOTOROLA, INC. Volume: Housing material: Interface connector: FCC ID: IHDT6AC1 D15 DVG with GPS: D15 DV DIN: D15 DV Standard: D15 DV Slim: D15 DVG with GPS: D15 DV DIN: Plastic housing PC/ABS d15 DV Standard / Slim/ DVG: d15 DV Vertical Board Only: d15 DV Horizontal Board Only: RF output connector: MMCX Jack (female) 50Ω connectors Plug (Male) Coax RG178 RG316 Huber-Shuhner 11-MMCX-50-1-1 11-MMCX-50-2-3 49g 22g cc cc cc cc 36 pin ZIF socket @ 0.
APPLICANT: MOTOROLA, INC. SIM Card Reader:¬ Interface: Host Protocol: FCC ID: IHDT6AC1 ETSI. PCS – Power levels # 15 to 0, 0 dBm to 30 dBm per FCC. Options: 1. Internal - chip SIM CR 3/5V SIM 2. External - Local interface 3/5 SIM 3. External - Remote interface (DSC interface) 5V only Options 1. 9 pin RS232 Serial Asynchronous full flow control , 5V logic level 2. 4 pin RS232 Serial Asynchronous using SoftGsm SW for PC applications, 5V logic levels. 3. Motorola Proprietary DSC Bus 4.
APPLICANT: MOTOROLA, INC. Data: PC FAX: SMS: Voice Call: Audio: GPS: FCC ID: IHDT6AC1 Transparent/Non transparent up to 14.400 bps. - V.42 bis when using SoftGSM only. Class 1,2 group 3 when using SoftGSM only Send and receive (PDU and block mode per GSM 07.
