Applicant: Motorola, Inc. FCC ID: AZ489FT7007 Exhibit VIII User Information and User Manual 1) User Card/Booklet - 2 pages, contains important information for safe usage and RF energy awareness and control information for compliance with RF energy exposure limits 2) User Service Manual HDT 600 Data Terminal - 29 PDF pages total, 22 numbered pages Please find the information required by Part 15.19, 15.21 & 15.105 in Owners Manual on page 7 of this PDF file, or click tab to FCC INTERFERENCE WARNING.
ab HANDHELD PORTABLE TERMINAL HDT600 BEFORE USING THIS RADIO TERMINAL, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. The information provided in this document supersedes information contained in user guides published prior to February 2002.
ries. Use of non-Motorola-approved, batteries and accessories may exceed FCC RF exposure guidelines. For additional information on RF exposure awareness information, visit the following Motorola website: www.mot.com/rfhealth. Electromagnetic Interference/Compatibility Note:Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise configured for electromagnetic compatibility.
Owner’s Manual HDT 600 Portable Data Terminal a Draft Feb 18 03 68P02966C70-O 68P02966C70-O @6802966C70@
Contents COMPUTER SOFTWARE COPYRIGHTS ii FCC INTERFERENCE WARNING v What is the HDT 600 Terminal 1 HDT 600 Parts 3 Unpacking 4 HDT 600 Cradle Connections 5 Installing the Battery 6 Removing the Battery 6 First Time Battery Charge 7 Charging the Battery 8 Battery Maintenance 9 Turning on the HDT 600 10 Suspend Mode 10 Turning off the HDT 600 10 Using the HDT 600 11 Using the Stylus Pen 11 Scanning With the HDT 600 12 Resetting the HDT 600 13 Cradle Installation 14 Maintaining the HDT 600 16 Accessories 17 Wh
COMPUTER SOFTWARE COPYRIGHTS The Motorola products described in this instruction manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including the exclusive right to copy or reproduce in any form the copyrighted computer program.
II. GENERAL PROVISIONS: This warranty sets forth the full extent of Motorola’s responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at Motorola’s option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. MOTOROLA DISCLAIMS ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
V. GOVERNING LAW In the case of a Product sold in the United States and Canada, this Warranty is governed by the laws of the State of Illinois and the Province of Ontario, respectively. VI.
FCC INTERFERENCE WARNING The FCC requires that manuals pertaining to Class A and Class B computing devices must contain warnings about possible interference with local residential radio and TV reception. This warning reads as follows: NOTE: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 90 of the FCC Rules.
What is the HDT 600 Terminal The HDT 600 is a portable terminal designed for field applications where fast data acquisition is required. Its ergonomic design is easy to hold and carry. Its unique shape fits the hand, and the back strap provides extra grip. The Windows CE operating system with touch screen and soft-keys provides easy access to various applications. The HDT 600 is equipped with a 3.6 inch color LCD screen with LED front-light, viewable in all light conditions, including direct sunlight.
• Wide Area Network (WAN) communication: 1. An optional GPRS radio module provides coverage within cellular infrastructure. 2. An optional DataTAC radio module provides coverage within DataTAC network infrastructure. 3. An optional iDEN radio module provides coverage within iDEN network infrastructure. It is also possible to use GPRS and WLAN communication by installing both radios within the HDT 600. In such case the HDT 600 software switches between radios when moving from one coverage area to another.
HDT 600 Parts Front View Buzzer Back View Barcode Scanner LASER Window LED Indicator Power Button (On/Off/Suspend) Barcode Scanner Triggers Battery Lock Touch Sensitive Screen Function Soft Keys Battery Hand Strap Stylus Pen Stylus Pen Silo Battery Charge & Communication Contacts Terminal Release Button Red LED indicating HDT 600 locked into Cradle Terminal Release Button HDT 600 Cradle 3
Unpacking The HDT 600 Data Terminal and HDT 600 Cradle are shipped in separate packages. The HDT 600 Data Terminal package includes the following items: • One HDT 600 Data Terminal unit • One 7.
HDT 600 Cradle Connections Important Note: This product should be installed according to local applicable laws and directives.
Installing the Battery The battery is shipped from the factory uncharged and not installed. Charge the battery before using the HDT 600 for the first time. 1. Before installing the battery, release the terminal hand strap, as shown below. 2. Verify that the battery lock is in Unlock position. 3. To install the battery, position the battery in the right-hand side of the battery compartment and lower it downward to its place. 4.
1. Turn the HDT 600 off by holding the Power button pressed for at least two seconds. 2. Release the terminal hand strap as shown in the figure above. 3. Use a coin to unlock the battery by turning the battery lock counter-clockwise. 4. To remove the battery, lift the left-hand side of the battery and pull it out. First Time Battery Charge The battery is charged when installed inside the HDT 600.
Charging the Battery The battery remaining capacity indication may show by the LED indicator of your HDT 600 (see figure below). Note that the HDT 600 can either be in On, Off or Suspend mode, while charging.
! Warning When installed in a vehicle, the HDT 600 must be locked into the Cradle. If not locked, the HDT 600 may be propelled with great force and may cause serious injury to occupants of the vehicle. Important Note: The HDT 600 will not charge if not locked into the Cradle. Once the HDT 600 is locked, the Cradle red LED will turn on, indicating lock status. 3. To remove the HDT 600 from the Cradle, press one or two unlock buttons until the HDT 600 pops out a bit, and remove the HDT 600 from the Cradle.
600, always replace the battery with a genuine Motorola replacement. Your Cradle will charge your battery effectively when it is at room temperature (approx. 20° C). Battery charging temperature range is 0°C to 45°C. Turning on the HDT 600 Press the Power button to start the HDT 600. The HDT 600 also powers on immediately when the battery is inserted. As the HDT 600 initializes its unique flash file system, the Motorola logo displays for about one minute.
Using the HDT 600 When using the HDT 600, the hand strap on the back of the unit provides stability. Insert your left or right hand under the strap while holding the stylus pen in the other hand. Using the Stylus Pen The Stylus pen selects items and enters information. Use the pen as you use your PC mouse. • • • To open and select screen items, tap on the item twice with the pen. To drag text or image items, hold the pen on the item and drag across the screen.
Scanning With the HDT 600 The HDT 600 is equipped with four scan trigger buttons, designed for left-handed and right-handed users. The buttons are located on the left-hand and right-hand sides of the terminal and on the lefthand and right-hand sides of the upper front panel. The HDT 600 has an integrated scanner which gathers data by scanning barcodes. To scan barcodes with the HDT 600, aim the scanner at the barcode. Press one of the four scan trigger buttons.
Resetting the HDT 600 Power Button You may need to reset your HDT 600; for example, you may reset due to communication cutoff with your desktop PC or radio network, or when the operating system stops responding. When your HDT 600 stops responding, do the following actions: Warm Boot Important Note: When HDT 600 is warm booted, all information remains stored in memory. 1. Simultaneously press soft keys 1, 2 and the Power button for at least 5 seconds; the HDT 600 will function again.
Cradle Installation The Cradle can be installed by using the four threaded holes on its back side (See figure in page 14). Use the holes to attach the Cradle to any surface, such as: vehicle dashboard, office wall or table. Planning is the key to fast, easy HDT 600 Cradle installation. Before a hole is drilled or a wire is run, inspect the vehicle and determine how and where you intend to mount the Cradle and accessories.
For continued protection against risk of fire, replace only with same type and rating of fuse.
Maintaining the HDT 600 In order to maintain your HDT 600 in good working order: • • • • • • • • 16 Do not scratch the screen. Use only Motorola supplied stylus pen with the touch-sensitive screen. Never use a pen or pencil or any sharp object on the screen. Although your HDT 600 is water and dust resistant, do not expose it to rain or moisture for long periods of time. Protect your HDT 600 from temperature extremes.
Accessories Motorola recommends the use of the following accessories with your terminal. Please refer to your company for more information. Motorola is not responsible for the use of accessories not approved for this product. The following Motorola approved accessories are for use with your terminal. For information on the availability of these accessories, please call your company supplier.
What to Do If Table 2: Troubleshooting Problem HDT 600 does not turn on. HDT 600 red LED does not stop blink or battery refuse to charge. HDT 600 does not detect scan input. 18 Cause Solution Battery not charged. Ensure proper battery installation in HDT 600. Charge or replace the battery. HDT 600 in Suspend mode. Press the Power Button. HDT 600 is not locked in Cradle. Reinstall HDT 600 in Cradle.
Table 2: Troubleshooting Problem HDT 600 stopped responding. Cause Solution Problem in HDT 600 operating system or communication network. Simultaneously press soft keys 1, 2 and the Power button for at least 5 seconds; the HDT 600 should function again. If still does not respond, simultaneously press soft keys 2, 3 and 4 to restart your HDT 600. The operation system will reboot for about a minute. Incomplete or no data transmission between HDT 600 and PC. HDT 600 is not locked in Cradle.
Battery Warnings and Disposal HDT 600 On Board Aircraft Always remove the battery from the HDT 600 when shipped via air. Any use of the HDT 600 must be in accordance with applicable regulations per airline crew instructions. Battery Disposal Batteries must be recycled or disposed of properly in accordance with local requirements. Recycling facilities may not exist in all areas. Please contact your local environmental agency for more information regarding proper disposal.
HOW TO REACH US: Commercial, Government and Industrial Solutions Sector 1301 E. Algonquin Road, Schaumburg, IL 60196 Visit our Web site at www.motorola.com MOTOROLA and the Stylized M Logo are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their respective owners. © Motorola, Inc. 2003.