User's Manual
Table Of Contents
- COMPUTER SOFTWARE COPYRIGHTS
- Notational Conventions
- Welcome
- What is the HC700-i Handheld Computer?
- Unpacking
- HC700-i Features
- Charging the Battery
- Figure 3. HC700-i Personal Desktop Cradle
- Checking the Remaining Battery Power
- First Time Battery Charge
- Routine Battery Charge
- Battery Replacement
- Figure 4. Battery Installation and Removal
- 1. Hold down the Power Button for at least four seconds until the HC700-i screen turns off.
- 2. Remove the HC700-i hand-strap (see Figure 4).
- 3. Press the battery snap on the battery (see Figure 4) and pull away the battery from the HC700-i.
- 4. Insert a fresh battery, bottom end first, into the battery compartment.
- 5. Carefully, press the battery top downward until it clicks and locks in place.
- Battery Safety
- Battery Maintenance
- Battery Disposal
- Using the HC700-i
- Starting to Work
- Using the Keypad
- Direct Action Keys
- Virtual Keyboard
- Wireless Manager
- Using the Phone
- SIM Card Installation
- Figure 7. SIM Card Installation
- 1. Turn off the HC700-i
- 2. Remove the battery
- 3. Open the SIM card door
- 4. Slide the SIM card holder forward to unlock the SIM card
- 5. Slide the new SIM card in the holder with the cut corner on the upper right and the gold plate...
- 6. Lower the SIM card holder and press downward to lock the SIM card holder
- 7. Close the SIM card door
- 8. Install the battery
- 9. Perform HW Cold Reset “Step 2: HW Cold Reset” on page32
- Turning on the phone
- Make a Phone Call
- Make a Dispatch call
- Answer a Call
- Make a call using speed dial
- Call Waiting
- Create a Contact from a Call
- Make a conference call
- Use Call Waiting
- Place a call on hold
- Speed Dial
- Adjusting the earpiece/speaker volume
- Change the ringer volume
- Change the ring type
- Change the ring tone
- Change services settings
- Internet connection using iDEN network
- 1. Tap Start Menu -> Settings -> Connections tab -> Connections -> Manage Existing connections
- 2. Tap and hold the stylus on your internet connection, press Connect on the opened menu.
- 1. Tap Start Menu -> Settings -> Connections tab -> Connections
- 2. In My ISP, tap Add a new modem connection
- 3. Enter a name for the connection (for example: My Link)
- 4. Select a mode: Cellular Line (iDEN) and tap Next
- 5. Enter the phone number provided by your ISP and tap Next
- 6. Enter User Name, Password and Domain provided by your ISP and tap Finish
- 7. Switch to Internet Explorer Mobile and surf the Internet. Your HC700 will connect automatically.
- SIM Card Installation
- Bluetooth Connection
- Turning on/off
- Create a Bluetooth link (partnership)
- 1. Tap Start Menu -> Settings -> System tab.
- 2. Tab the Bluetooth Monitor icon
- 3. Tap Device -> Find Devices. Your device searches for other remote devices, and displays them o...
- 4. Tap Device -> Trust this Device.
- 5. Passkey is used to secure your HC700-i. You can use a passkey by entering a alphanumeric passk...
- 6. If you use passkey, enter the same passkey on the other device. You may change the name of the...
- Wireless LAN Connection
- Sending files by IrDA
- 1. Tap and hold the stylus on the file you wish to send.
- 2. From the opened menu select "Beam File".
- 3. Place the HC700 and the target device IrDA windows aligned. Make sure that nothing is between ...
- 4. Confirm the file transfer at the target device. During the file transfer, an icon will show on...
- Adjusting the Phone Volume
- Voice Recording
- Scanning Barcodes
- Calibrating the Touch Screen
- Resetting the HC700-i
- Allocating Memory
- miniSD Memory Card
- Service
- ActiveSync (USB) Connectivity
- Troubleshooting
15
Key Assignment
Table 3: HC700-i - Key Assignment
Key Function
Use the <TAB/Send> key to make & answer
phone calls. The key also serves as <TAB> key
when editing text.
Use the <Esc> key to exit from a menu or an
application.
The <End> key turns the phone off and ends a
call.
The
Main Scan Button is used for scanning
barcodes (refer to “Scanning Barcodes” on
page 30).
The 4 Way Navigation key is used for screen
navigation. The <Up bump> and <Down bump>
keys are used to scroll up and down. The <Right
bump> and <Left bump> are used for horizontal
navigation between action buttons and entry
fields.
The <ENT> key is used to continue to the next
field/screen (i.e., continue processing).
The <SP> key enables entering blank space(s)
within a text field. The <SP> key is active only
on those text entry screens which contain fields
that allow spaces to be entered.
TAB
ESC
Enhanced IMD Users.book Page 15 Tuesday, September 26, 2006 2:17 PM