User's Manual
Table Of Contents
- COMPUTER SOFTWARE COPYRIGHTS
- Notational Conventions
- Welcome
- What is the HC700-i Handheld Computer?
- Unpacking
- HC700-i Features
- Charging the Battery
- Figure 3. HC700-i Personal Desktop Cradle
- Checking the Remaining Battery Power
- First Time Battery Charge
- Routine Battery Charge
- Battery Replacement
- Figure 4. Battery Installation and Removal
- 1. Hold down the Power Button for at least four seconds until the HC700-i screen turns off.
- 2. Remove the HC700-i hand-strap (see Figure 4).
- 3. Press the battery snap on the battery (see Figure 4) and pull away the battery from the HC700-i.
- 4. Insert a fresh battery, bottom end first, into the battery compartment.
- 5. Carefully, press the battery top downward until it clicks and locks in place.
- Battery Safety
- Battery Maintenance
- Battery Disposal
- Using the HC700-i
- Starting to Work
- Using the Keypad
- Direct Action Keys
- Virtual Keyboard
- Wireless Manager
- Using the Phone
- SIM Card Installation
- Figure 7. SIM Card Installation
- 1. Turn off the HC700-i
- 2. Remove the battery
- 3. Open the SIM card door
- 4. Slide the SIM card holder forward to unlock the SIM card
- 5. Slide the new SIM card in the holder with the cut corner on the upper right and the gold plate...
- 6. Lower the SIM card holder and press downward to lock the SIM card holder
- 7. Close the SIM card door
- 8. Install the battery
- 9. Perform HW Cold Reset “Step 2: HW Cold Reset” on page32
- Turning on the phone
- Make a Phone Call
- Make a Dispatch call
- Answer a Call
- Make a call using speed dial
- Call Waiting
- Create a Contact from a Call
- Make a conference call
- Use Call Waiting
- Place a call on hold
- Speed Dial
- Adjusting the earpiece/speaker volume
- Change the ringer volume
- Change the ring type
- Change the ring tone
- Change services settings
- Internet connection using iDEN network
- 1. Tap Start Menu -> Settings -> Connections tab -> Connections -> Manage Existing connections
- 2. Tap and hold the stylus on your internet connection, press Connect on the opened menu.
- 1. Tap Start Menu -> Settings -> Connections tab -> Connections
- 2. In My ISP, tap Add a new modem connection
- 3. Enter a name for the connection (for example: My Link)
- 4. Select a mode: Cellular Line (iDEN) and tap Next
- 5. Enter the phone number provided by your ISP and tap Next
- 6. Enter User Name, Password and Domain provided by your ISP and tap Finish
- 7. Switch to Internet Explorer Mobile and surf the Internet. Your HC700 will connect automatically.
- SIM Card Installation
- Bluetooth Connection
- Turning on/off
- Create a Bluetooth link (partnership)
- 1. Tap Start Menu -> Settings -> System tab.
- 2. Tab the Bluetooth Monitor icon
- 3. Tap Device -> Find Devices. Your device searches for other remote devices, and displays them o...
- 4. Tap Device -> Trust this Device.
- 5. Passkey is used to secure your HC700-i. You can use a passkey by entering a alphanumeric passk...
- 6. If you use passkey, enter the same passkey on the other device. You may change the name of the...
- Wireless LAN Connection
- Sending files by IrDA
- 1. Tap and hold the stylus on the file you wish to send.
- 2. From the opened menu select "Beam File".
- 3. Place the HC700 and the target device IrDA windows aligned. Make sure that nothing is between ...
- 4. Confirm the file transfer at the target device. During the file transfer, an icon will show on...
- Adjusting the Phone Volume
- Voice Recording
- Scanning Barcodes
- Calibrating the Touch Screen
- Resetting the HC700-i
- Allocating Memory
- miniSD Memory Card
- Service
- ActiveSync (USB) Connectivity
- Troubleshooting
32
Step 1: Warm Reset
Important Note: When
the HC700-i performs
Warm Reset, all recorded
information remains
stored in RAM file sys-
tem. To perform Warm
Reset, perform the fol-
lowing:
Hold down the <ESC>
and <A> and <F> keys
(see Figure 10) for at least 5 seconds - the Motorola logo will
show on the screen for about 30 seconds and then Windows
Mobile desktop or application screen will appear - the
HC700-i functions again. Warm Reset can also be performed
in the following way: go to: Start Menu -> Settings -> Device
Boot - selecting “Warm Boot” and tapping on the “Perform
Boot” button.
If the HC700-i still does
not respond, perform
Step 2 HW Cold Reset:
Step 2: HW Cold
Reset
HW Cold Reset restarts
the HC700-i by erasing
all stored records and
entries from the Ram-
disk.
Do Not perform HW
Cold Reset unless Warm
Reset fails to solve the
problem. To perform HW Cold Reset, perform the following:
Hold down the Power Button and <S> and <X> keys for at
least 5 seconds (see Figure 11); the HC700-i will restart its
operating system. HW Cold Reset can also be performed in
the following way: go to: Start Menu -> Settings -> Device
F
igure 10. Warm Reset - Key Combination
igure 11. HW Cold Reset - Key Combinatio
n
Enhanced IMD Users.book Page 32 Tuesday, September 26, 2006 2:17 PM