User's Manual
Table Of Contents
- COMPUTER SOFTWARE COPYRIGHTS
- Notational Conventions
- Welcome
- What is the HC700-i Handheld Computer?
- Unpacking
- HC700-i Features
- Charging the Battery
- Figure 3. HC700-i Personal Desktop Cradle
- Checking the Remaining Battery Power
- First Time Battery Charge
- Routine Battery Charge
- Battery Replacement
- Figure 4. Battery Installation and Removal
- 1. Hold down the Power Button for at least four seconds until the HC700-i screen turns off.
- 2. Remove the HC700-i hand-strap (see Figure 4).
- 3. Press the battery snap on the battery (see Figure 4) and pull away the battery from the HC700-i.
- 4. Insert a fresh battery, bottom end first, into the battery compartment.
- 5. Carefully, press the battery top downward until it clicks and locks in place.
- Battery Safety
- Battery Maintenance
- Battery Disposal
- Using the HC700-i
- Starting to Work
- Using the Keypad
- Direct Action Keys
- Virtual Keyboard
- Wireless Manager
- Using the Phone
- SIM Card Installation
- Figure 7. SIM Card Installation
- 1. Turn off the HC700-i
- 2. Remove the battery
- 3. Open the SIM card door
- 4. Slide the SIM card holder forward to unlock the SIM card
- 5. Slide the new SIM card in the holder with the cut corner on the upper right and the gold plate...
- 6. Lower the SIM card holder and press downward to lock the SIM card holder
- 7. Close the SIM card door
- 8. Install the battery
- 9. Perform HW Cold Reset “Step 2: HW Cold Reset” on page32
- Turning on the phone
- Make a Phone Call
- Make a Dispatch call
- Answer a Call
- Make a call using speed dial
- Call Waiting
- Create a Contact from a Call
- Make a conference call
- Use Call Waiting
- Place a call on hold
- Speed Dial
- Adjusting the earpiece/speaker volume
- Change the ringer volume
- Change the ring type
- Change the ring tone
- Change services settings
- Internet connection using iDEN network
- 1. Tap Start Menu -> Settings -> Connections tab -> Connections -> Manage Existing connections
- 2. Tap and hold the stylus on your internet connection, press Connect on the opened menu.
- 1. Tap Start Menu -> Settings -> Connections tab -> Connections
- 2. In My ISP, tap Add a new modem connection
- 3. Enter a name for the connection (for example: My Link)
- 4. Select a mode: Cellular Line (iDEN) and tap Next
- 5. Enter the phone number provided by your ISP and tap Next
- 6. Enter User Name, Password and Domain provided by your ISP and tap Finish
- 7. Switch to Internet Explorer Mobile and surf the Internet. Your HC700 will connect automatically.
- SIM Card Installation
- Bluetooth Connection
- Turning on/off
- Create a Bluetooth link (partnership)
- 1. Tap Start Menu -> Settings -> System tab.
- 2. Tab the Bluetooth Monitor icon
- 3. Tap Device -> Find Devices. Your device searches for other remote devices, and displays them o...
- 4. Tap Device -> Trust this Device.
- 5. Passkey is used to secure your HC700-i. You can use a passkey by entering a alphanumeric passk...
- 6. If you use passkey, enter the same passkey on the other device. You may change the name of the...
- Wireless LAN Connection
- Sending files by IrDA
- 1. Tap and hold the stylus on the file you wish to send.
- 2. From the opened menu select "Beam File".
- 3. Place the HC700 and the target device IrDA windows aligned. Make sure that nothing is between ...
- 4. Confirm the file transfer at the target device. During the file transfer, an icon will show on...
- Adjusting the Phone Volume
- Voice Recording
- Scanning Barcodes
- Calibrating the Touch Screen
- Resetting the HC700-i
- Allocating Memory
- miniSD Memory Card
- Service
- ActiveSync (USB) Connectivity
- Troubleshooting
33
Boot - selecting “Hw Cold Boot” and tapping on the “Perform
Boot” button.
Step 3: SW Clean Reset
SW Clean Reset restarts the HC700-i by erasing all stored
records and entries from the RAM file system and the RAM-
disk. The SW Clean Reset also sets the HC700-i to its default
settings.
Do Not perform SW Clean Reset unless HW Cold Reset fails
to solve the problem. To perform SW Clean Reset, perform
the following:
Hold down the Power Button and <S> and <X> keys for at
least 5 seconds and release. Now, hold down the <S> and
<X> and <C> keys for at least 5 seconds and release.
The HC700-i will restart its operating system. SW Clean
Reset can also be performed in the following way: go to:
Start Menu -> Settings -> Device Boot - selecting “Sw Cold
Boot” and tapping on the “Perform Boot” button.
Allocating Memory
You can allocate the HC700-i memory by setting the size of
the storage and the programs memory. You can also view the
amount of memory used by running programs or storage
space.
To view and allocate the memory of the HC700, go to: Start ->
Settings -> System -> Memory.
Enhanced IMD Users.book Page 33 Tuesday, September 26, 2006 2:17 PM