SRX2200_M3.5_FrontCover.fm Page 1 Wednesday, March 27, 2013 6:51 PM SRX™ TWO-WAY RADIOS SRX 2200 MODEL 3.
QR-Card.fm Page 1 Friday, June 5, 2015 7:29 PM m ASTRO® SRX™ 2200 Series Digital Portable Radios Quick Reference Card 16-Position Select Knob __________ On/Off/Volume Control Knob RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios ATTENTION! This radio is restricted to Occupational use only.
QR-Card.fm Page 2 Friday, June 5, 2015 7:29 PM Sending an Emergency Call 1 Press the Emergency button. 2 Press and hold the PTT button. Speak clearly into the microphone. v The more stripes, the stronger the signal strength for the current site (trunking only). m O Direct radio to radio communication or connected through a repeater. On = Direct Off = Repeater On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. l On = AES Secure operation.
Documentation Copyrights...........16 Declaration of Conformity......................... 9 Disclaimer.......................................17 Important Safety Information........11 Getting Started............................... 18 Software Version............................12 Notice to Users (FCC and Industry Canada)....................................................12 Consignes de sécurité importantes.................................13 Version logicielle...........................
Attaching the Antenna................................... 22 Removing and Attaching the Accessory Connector Cover...................................... 23 Using the Carry Holder.................................. 24 Turning On the Radio.................................... 26 Adjusting the Volume.....................................27 Identifying Radio Controls............ 28 Contents Radio Parts and Controls...............................28 Programmable Features................................
Advanced Features........................67 Advanced Call Features................................ 67 Selective Call (ASTRO Conventional Only)........................ 67 Talkgroup Call Feature (Conventional Operation Only)...... 68 Sending a Status Call......................... 69 Responding to the Dynamic Regrouping Feature (Trunking Only).............................................. 69 Dynamic Zone Programming (DZP)....71 Contacts.........................................................
Contents Making a Dynamic Priority Change (Conventional Scan Only).............. 82 Deleting a Nuisance Channel............. 82 Restoring a Nuisance Channel........... 83 Call Alert Paging............................................ 83 Receiving a Call Alert Page................ 83 Sending a Call Alert Page...................84 Quick Call II (ASTRO P25 Digital Trunking and Conventional)..................... 85 Initiating a Quick Call II Transmission................................. 86 Emergency Operation..
Geofence (ASTRO 25 Trunking System).... 134 Entering the Geofence Area............. 135 Trunking System Controls........................... 136 Operating in Failsoft System.............136 Out-of-Range Radio..........................136 Site Trunking Feature....................... 137 Locking and Unlocking a Site............137 Site Display and Search Button........ 137 ® Mission Critical Wireless - Bluetooth -........ 138 Turning On Bluetooth .......................139 Turning Off the Bluetooth............
Contents Adjusting the Volume of the Radio from Bluetooth Audio Device....... 150 Viewing and Clearing the Bluetooth Device Information....................... 151 Clearing All Bluetooth Devices Information................................... 152 Editing the Bluetooth Friendly Name........................................... 153 Over-the-Air Programming (POP 25, ASTRO 25, ASTRO Conventional).........153 Responding to the Notification of Upgrade....................................... 154 Voice Announcement....
Helpful Tips.................................. 179 Radio Care...................................................179 Cleaning Your Radio.........................180 Preparation for Washing the Radio and Parts..................................... 180 Proper Ways to Handle the Radio.... 185 Radio Service and Repair................. 185 Battery Care.................................................186 Battery Charge Status.......................186 Battery Recycling and Disposal........ 187 Accessories.........
Contents VIII. For Australia Only.................................
Declaration of Conformity Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. Declaration of Conformity Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola Solutions, Inc. Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A. Phone Number: 1-800-927-2744 Hereby declares that the product: Model Name: SRX 2200 conforms to the following regulations: FCC Part 15, subpart B, section 15.
Class B Digital Device As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause undesired operation. Declaration of Conformity Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios ATTENTION! This radio is restricted to Occupational use only. Before using the radio, read the RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations.
Software Version All the features described in the following sections are supported by the software version R14.00.00 or later. See Accessing the Radio Information on page 175 to determine the software version of your radio. Check with your dealer or system administrator for more details of all the features supported.
Radios bidirectionnelles portatives : exposition aux radiofréquences et sécurité du produit ATTENTION! Cette radio ne doit être utilisée qu'à des fins professionnelles.
Version logicielle Toutes les fonctions décrites dans les sections suivantes sont prises en charge par la version R14.00.00 ou les versions ultérieures du logiciel de la radio. Pour obtenir davantage de renseignements à propos des fonctions prises en charge, adressez-vous à votre détaillant ou à votre administrateur de système.
Computer Software Copyrights Computer Software Copyrights The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program.
Documentation Copyrights Documentation Copyrights No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola.
Disclaimer Disclaimer The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes to any products herein to improve readability, function, or design. Motorola does not assume any liability arising out of the applications or use of any product or circuit described herein; nor does it cover any license under its patent rights, nor the rights of others.
damage to the equipment if not carefully observed. Getting Started Note: An operational procedure, practice, or condition and so on, which is essential to emphasize. How to Use This Guide This User Guide covers the basic operation of the APX Portables. However, your dealer or system administrator may have customized your radio for your specific needs. Check with your dealer or system administrator for more information.
The following performance enhancements are some of the latest creations designed to enhance the security, quality and efficiency of the radios. ASTRO 25 Enhanced Data ASTRO 25 Enhanced Data is optimized to handle different message sizes and variable update rates from different applications of the radio. Add Enhanced Data to the Integrated Data system with a software installation to improve data channel efficiency and enable denser network traffic.
single conventional radio frequency channel. These enhancements allow users to use Selective Squelch to operate on only the subset of talkgroups that are relevant to the users rather than all talkgroups on the channel. These Scan improvements have been made to eliminate the audio holes that were present and to turn on the busy LED when activity is present on the channel. Mixed Vote Scan and Standard Conventional Scan configurations are supported. Priority Operation is also supported.
This section provides simple instructions to prepare your radio for use. Charging the Battery Warning: To avoid a possible explosion: • • Do not replace the battery in any area labeled hazardous atmosphere. Do not discard batteries in a fire. The Motorola-approved battery shipped with your radio is uncharged. Prior to using a new battery, charge it for a minimum of 16 hours to ensure optimum capacity and performance.
Preparing Your Radio for Use A 2 To remove the battery, squeeze the release latches at the bottom of the battery until the battery releases from the radio and remove the battery from the radio. 22 English Note: When removing the battery, ensure that the radio is turned off. Attaching the Antenna Ensure the radio is turned off before attaching the antenna. 1 Set the antenna in its receptacle.
Preparing Your Radio for Use 2 Turn the antenna clockwise to attach to the radio. Removing and Attaching the Accessory Connector Cover The accessory connector is on the antenna side of the radio. It is used to connect accessories to the radio. Note: To prevent damage to the connector, shield it with the connector cover when not in use. 1 To remove the accessory connector cover, rotate the thumbscrew counterclockwise until it disengages from the radio.
6 Once in place, tighten by rotating the thumbscrew clockwise by hand. A Using the Carry Holder 1 Position the radio within the carry holder with the main speaker facing outward. B Preparing Your Radio for Use C 2 Rotate and lift the connector cover to disengage it from the radio. 3 Slide the accessory connector cover over the antenna and position at the base of the antenna. 4 To attach the accessory connector cover, insert the hooked end of the cover into the slot above the connector.
Preparing Your Radio for Use 3 To remove the radio from the carry holder, place the tip of your fingers on the ledge of the carry holder. 4 Push at the bottom of the radio until the radio is released from it.
Preparing Your Radio for Use • Turning On the Radio 1 Rotate the On/Off/Volume Control Knob clockwise until you hear a click. • If the power-up test is successful, you see momentary SELFTEST on the radio display, followed by the Home screen. If the power-up test is unsuccessful, you see Error XX/YY (XX/YY is an alphanumeric code). Note: If the radio fails to power-up after repeating a few times, record the Error XX/YY code and contact your dealer.
Preparing Your Radio for Use A Adjusting the Volume Ensure the radio is power on and the main speaker is pointed towards you for increased loudness and intelligibility, especially in areas with loud background noises. 2 To decrease the volume, rotate this knob counterclockwise. 1 To increase the volume, rotate the On/Off/Volume Control Knob clockwise.
25 Identifying Radio Controls 24 Radio Parts and Controls 1 2 3 4 15 23 16 22 14 13 12 17 11 21 Identifying Radio Controls 18 5 10 6 9 7 8 28 English 20 19 8 1 Antenna 2 LED 3 Top (Orange) Button[1] 4 Microphone
Identifying Radio Controls 1 5 Accessory Connector 21 Bluetooth Pairing Location Indicator 6 Home Button 22 Main Speaker 7 4–Way Navigation Button 23 Microphone 8 Battery Latch 24 Top Display 9 Keypad 25 16-Position Select Knob[1] 10 Data Feature Button 11 Menu Select Buttons 12 Main Display 13 3–Position A/B/C Switch[1] 14 2–Position Concentric Switch[1] 15 On/Off/Volume Control Knob 16 Top Side (Select) Button[1] 17 Push-to-Talk (PTT) Button Your dealer can program th
Long press Pressing and holding for the preprogrammed duration (between 0.25 seconds and 3.75 seconds). Hold down Keeping the button pressed. Identifying Radio Controls Assignable Radio Functions 30 English Bluetooth Inquiry Enables Bluetooth Search On/Off feature. Bluetooth Discoverable On/Off Enables Bluetooth visibility. This is accessed by a long press of the Bluetooth Inquiry On/Off Button. Call Alert Allows the radio to function like a pager, or to verify if a radio is active on the system.
Depending on the programming, initiates or cancels an emergency alarm or call. Information Displays the information of the radio. Internet Protocol Address Display the Internet Protocol (IP) address, device name and status of the radio. Location Determines the current location (latitude, longitude, time and date), and also the distance and bearing to another location. Or, turns the GPS functionality on or off for all locations.
Identifying Radio Controls 32 English Phone Allows you to make and receive calls similar to standard phone calls. Private Call (Trunking Only) Allows a call from an individual radio to another individual radio. Private Line Defeat (Conventional Only) Overrides any coded squelch (DPL or PL) that is preprogrammed to a channel. Query Launches a list of predefined short text messages only after successfully logged in the twoFactor Authentification.
Site Lock/Unlock (Trunking Only) Locks onto a specific site. Status (Astro 25 Trunking Only) Sends data calls to the dispatcher about a predefined status. Talkaround/ Direct (Conventional Only) Toggles between using a repeater and communicating directly with another radio. Talkgroup (Conventional Only) Allows a call from an individual radio to a group of radios. Text Messaging Service (TMS) Selects the text messaging menu. TMS Quick Text Selects a predefined message.
Voice Announcement Audibly indicates the current feature mode, Zone or Channel the user has just assigned. Voice Mute Toggles voice mute on or off. Volume Set Tone Sets the volume set tone. A B E D Accessing the Preprogrammed Functions Identifying Radio Controls You can access various radio functions through one of the following methods. • A short or long press of the relevant programmable buttons. • Use the Menu Select Button. • Use the Menu Select and Navigation buttons.
Press the Menu Select button directly below Chan. Home Button Pressing the button returns you to the Home (default) screen. In most cases, this is the current mode. For selected radio features, the button is also used to save user-edited radio settings or information before returning you to the Home screen. Note: Some features do not require you to press to go to the Home screen. Refer to the individual feature sections in this manual for further details on saving user-edited radio settings or information.
Keypad Characters – Uppercase Mode Identifying Radio Controls Key Number of Times Key is Pressed 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 1 . , ? ! ; @ _ - * # & $ / + = \ “ ‘ ( ) A B C D E F G H I J K L M N O P Q R T U V W X Y S Z Toggle between mixed case mode, uppercase mode and lowercase mode. Space 36 English Toggle between numeric and letter mode.
Key Identifying Radio Controls Keypad Characters – Lowercase Mode Number of Times Key is Pressed 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 1 . , ? ! ; @ _ - * # & $ / + = \ “ ‘ ( ) a b c d e f g h i j k l m n o p q r t u v w x y s z Toggle between mixed case mode, uppercase mode and lowercase mode. Space Toggle between numeric and letter mode.
Keypad Characters – Numeric Mode Key Number of Times Key is Pressed 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 1 . , ? ! ; @ _ - * # & $ / + = \ “ ‘ ( ) 2 3 4 Identifying Radio Controls 5 6 7 8 9 0 Space 38 English Toggle between numeric and letter mode.
Key Identifying Radio Controls Keypad Characters – Hexadecimal Mode Number of Times Key is Pressed 1 2 3 4 2 A B C 3 D E F 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 1 4 5 6 7 8 9 0 Not applicable Not applicable 39 English
Push-To-Talk (PTT) Button Identifying Radio Controls A The PTT button basic purposes: • on the side of the radio serves two While a call is in progress, the PTT button allows the radio to transmit to other radios in the call. Press and hold down PTT button to talk. Release the PTT button to listen. The microphone is activated when the PTT button is pressed. 40 English • While a call is not in progress, the PTT button is used to make a new call.
Identifying Status Indicators Identifying Status Indicators Call Received Status Icons Radio has received an Individual Call. The 130 x 130 pixel front liquid crystal display (LCD) of your radio shows radio status, text entries, and menu entries. The top two display rows contain color icons that indicate radio operating conditions. Selected icons are also shown on the first row of the 112 x 32 pixel top monochrome display screen of your radio.
Top Display: Off – The feature is disabled. Voice muting of the affiliated trunking talkgroup or selected conventional channel is deactivated. Direct Top Display: On – Radio is currently configured for direct radio-to-radio communication (during conventional operation only). or Top Display: Identifying Status Indicators Top Display: Selected channel is being monitored (during conventional operation only). L – Radio is set at Low power. H – Radio is set at High power.
View/Program Mode Radio is in the view or program mode. Top Display: , On steady – View mode Blinking – Program mode , Top Display: or The vote scan feature is enabled. until Basic Zone Bank 1 A – Radio is in Zone 1. C – Radio is in Zone 3. Top Display: Basic Zone Bank 2 or A – Contains Zone 1, Zone 2 and Zone 3, B – Contains Zone 4, Zone 5 and Zone 6, or until X – Contains Zone 70, Zone 71 and Zone 72, Y – Contains Zone 73, Zone 74 and Zone 75. B – Radio is in Zone 2.
AES Secure Operation On – AES secure operation. Inverted – User successfully login to the secured IP Packet Data. Off – Clear operation. Data Activity Blinking – Receiving an encrypted voice call. Data activity is present. Hexadecimal GPS Signal On – Feature is enabled and signal is available. Identifying Status Indicators Off – Feature is disabled. Blinking – Feature is enabled, but no signal is available. User Login Indicator (IP Packet Data) On – User is currently associated with the radio.
Bluetooth On Indicates that the text entry is currently in uppercase mode. Bluetooth is on and ready for Bluetooth connection. Lowercase Top Display: Identifying Status Indicators Uppercase Indicates that the text entry is currently in lowercase mode. Bluetooth Connected Lowercase Predictive Indicates that the text entry is currently in lowercase and with predicted words shown at the bottom of the screen. Top Display: Bluetooth is currently connected to the external Bluetooth device.
TMS Status Icons Normal Message The following icons appear on the radio’s display when you send and receive text messages. Inbox Full The Inbox is full. Message Sent The text message is sent successfully. Identifying Status Indicators Message Unsent User is composing a message with normal priority and without a request for a reply. Message Index Indicates the index of the current message the user is viewing.
• • User is composing a message with a priority status and a request for a reply. Messages in the Inbox folder are flagged with “Priority” and “Request Reply”. TMS Menu Options Menu Option Description/Function Back Brings you back to the previous screen. Clr Deletes all messages. Del Deletes a message or text. Edit Brings you to the edit screen. Exit Exits to the Home screen. No Returns to the previous screen. Optn Brings you to the Options main screen. Rply Replies to a message.
Solid red Radio is transmitting. Blinking red Radio is transmitting at low battery condition. Incoming call or data. Double blinking red Radio is in Emergency Mode. Outgoing call or data. Rapidly blinking red Radio has failed the self test upon powering up or encountered a fatal error. Solid yellow (Conventional Only) Channel is busy. Blinking yellow Radio is receiving a secured transmission.
Radio is on a Priority-One channel while in the Scan List Programming mode. Note: No LED indication when the radio receives a clear (non-secured) transmission in trunking Mode. LED indication can be preprogramed by qualified technician to be permanently disabled. Consult your dealer for further details if you want to disable it.
Backlight and Bar Color Notification When The radio is unable to establish a full connection with the system. The radio is unable to authenticate or register with the system. The radio lost GPS signal or GPS function fails. Green Call Alerts The radio receives a private call. The radio receives a phone call. The radio receives a call alert. Identifying Status Indicators The radio receives a selective call. The radio enters Geofence.
Long, LowPitched Tone Tone Name Heard No ACK Received When radio fails to receive an acknowledgment. Individual Call Warning Tone When radio is in an individual call for greater than 6 seconds without any activity. Man Down Entry When radio initiates Man Down mode. Time-Out Timer Timed Out After time out. Talk Prohibit/PTT Inhibit (When PTT button is pressed) transmissions are not allowed.
You Hear Long, MediumPitched Tone Tone Name Heard Clear Voice At beginning of a non-coded communication. Priority Channel Received When activity on a priority channel is received. Emergency Alarm /Call Entry When entering the emergency state. Central Echo When central controller has received a request from a radio. Volume Set When volume is changed on a quiet channel. Emergency Exit When exiting the emergency state.
Identifying Status Indicators You Hear Tone Name Heard Short, HighPitched Tone (Chirp) Low-Battery Chirp When battery is below preset threshold value. Two HighPitched Tones GPS Fails When the GPS signal is lost or when GPS fails. Ringing Fast Ringing When system is searching for target of Private Call. Enhanced Call Sent When waiting for target of Private Call to answer the call. Phone Call Received When a land-to-mobile phone call is received.
Identifying Status Indicators You Hear Tone Name Heard DecrementalPitched Tone Bluetooth Unpaired When Bluetooth accessory is unpaired from the radio. Bluetooth Disconnected When Bluetooth accessory is disconnected from the radio. A Group of Very HighPitched Tones Man Down Continuous Tone When radio is in Man Down mode and prepares to transmit Emergency Alarm when the timer of this alarm ends.
You See When Notes Phone busy The phone system is busy. Press to exit the phone mode and try your call later. A Busy Tone Phone busy When a channel is not available. The radio automatically connects when a channel opens. – No acknowledge The call is not acknowledged. Press to hang up. The radio returns to the Home screen. When you release the PTT button. The radio indicates to the landline party that he or she may begin talking.
a) or to Zone and press the Menu Select button directly below Zone. b) or to the required zone, or use the keypad to enter the zone number. If the zone number entered is unprogrammed, the display shows Invalid entry. Repeat this step. c) Press the Menu Select button directly below Sel to confirm the displayed zone. d) Press the PTT button to transmit on the displayed zone channel. General Radio Operation Selecting a Zone Your radio must be preprogrammed to allow you to use this feature.
• • Select a channel via the preprogrammed 16– Position Select Knob to the desired channel. a) Rotate the preprogrammed 16–Position Select Knob to the desired channel. b) Press the PTT button to transmit on the displayed zone channel. Select a channel via the radio menu Chan: a) or to Chan. b) Press the Menu Select button directly below Chan. or to the required channel or use the c) keypad to enter the channel number. If the channel number entered is unprogrammed, the display shows Invalid entry.
• or to CSrh and press the Menu Select button directly below CSrh. A blinking cursor appears on the Channel Search screen. 2 Use the keypad to type or edit your channel name. 3 To initiate searching, press the Menu Select button directly below CSrh once the entry is done. To exit this procedure, press the Menu Select button directly below Cncl. General Radio Operation The display shows Searching.
or to MS1, MS2 ... or MS5. 3 Press and hold the Menu Select button directly below one of the softkey (MS1 – MS5). You hear a short, medium-pitched tone when the zone and channel is saved. Note: To change the programmed zone and channel, repeat this procedure. Short press of the programmed softkey changes your current transmission to the zone and channel programmed in this softkey.
one of the following scenarios depending on the system your radio is configured: • General Radio Operation • For ASTRO Conventional system, the LED lights up solid yellow. The display shows the talkgroup alias or ID, and the caller alias or ID. For Trunking system, the display shows the caller alias or ID. Note: With the inactivity timer enabled (optional), when there is no response from the receiving radio, the calling radio exits the call with Menu Inactive Exit tone after the timer expires.
2 Press and hold the PTT button to talk. Release the PTT button to listen. See also Making a Private Call (Trunking Only) on page 62 for details on making a Private Call. 3 Press or the Call Response button to hang up and return to the Home screen. Receiving and Responding to a Telephone Call (Trunking Only) This feature allows you to receive calls similar to standard phone calls from a landline phone.
Making a Talkgroup Call To make a call to a group of users, your radio must be configured as part of that talkgroup. 1 Turn the 16-Position Select Channel Knob to select the channel with the desired talkgroup. This feature allows you to send an individual Call Alert or page if there is no answer from the target radio. 1 Perform one of the following actions: • 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to make the call.
or to the required ID. Use the keypad to enter the required ID. 1 Perform one of the following actions: • 4 Press the PTT button to initiate the Private Call. The display shows Calling... . 5 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. When you are connected, the display shows the ID of the target radio. If no acknowledgment is received, the display shows No acknowledge. 6 Press and hold the PTT button to talk. Release the PTT button to listen.
The display shows Calling... . 5 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. When you are connected, the display shows the ID of the target radio. If no acknowledgment is received, the display shows No acknowledge. If the target radio does not respond before the time out, the display shows No answer. General Radio Operation 6 Press and hold the PTT button to talk. Release the PTT button to listen.
7 Press to return to the Home screen. See Phone Call Displays and Alerts on page 54 for more information if your call is NOT answered. Switching Between Repeater or Direct Operation Button The Repeater Operation increases the radio coverage area by connecting with other radios through a repeater. The transmit and receive frequencies are different. The Direct or “talkaround operation” allows you to bypass the repeater and connect directly to another radio.
You can use the options interchangeably depending on your preference and the programmed functions. • General Radio Operation • • 66 English Monitoring a Channel with Volume Set button. a) Select the desired zone and channel. b) Press and hold the Volume Set button to hear the volume set tone. c) Adjust the Volume Control Knob if necessary. d) Release the Volume Set button. e) Press and hold the PTT button to transmit. The LED lights up solid red. f) Release the PTT button to receive (listen).
2 Press and hold the PTT button to talk. Release the PTT button to listen. Advanced Call Features Making a Selective Call Selective Call (ASTRO Conventional Only) 1 Perform one of the following actions: This feature allows you to receive a call from or to call a specific individual. It is intended to provide privacy and to eliminate the annoyance of having to listen to conversations that are of no interest to you.
• • or to the required ID. Use the keypad to enter the required ID. 4 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 5 Press and hold the PTT button to start the Selective Call. The display shows the ID of the target radio. 6 Release the PTT button to listen. 7 Press to return to the Home screen.
This feature allows you to send data calls to the dispatcher about a predefined status. Each status can have up to a 14-character name. A maximum of eight status conditions is possible. Note: The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit. 1 Perform one of the following actions: • • Press the preprogrammed Status button.
Note: If you try to access a zone or channel that has been reserved by the dispatcher as a dynamically regrouped mode for other users, you hear an invalid tone. When your radio is dynamically regrouped, it automatically switches to the dynamically regrouped channel. You hear a Gurgle tone and the display shows the dynamically regrouped channel’s name. Press the PTT button to talk. Release PTT button to listen.
Select-disabled radios cannot change channels while dynamically regrouped. The dispatcher has forced the radio to remain on the dynamic-regrouping channel. The Scan or Private Call feature cannot be selected while your radio is Select Disabled. Dynamic Zone Programming (DZP) Note: Your radio must be preprogrammed to allow you to use this feature. This feature works on the condition at least one zone in the radio must be a non-dynamic zone.
Saving a Channel in the Dynamic Zone from List Selection The radio must be in Dynamic Zone in order to perform this operation. 1 or to ZnPr. Press the Menu Select button directly below ZnPr to enter Program Zone screen. 6 Press the Menu Select button directly below Exit to return to Home screen. Saving a Channel in the Dynamic Zone from Channel Name The radio must be in Dynamic Zone in order to perform this operation. 1 Advanced Features 2 Press the Menu Select button directly below Edit.
The display shows Searching.... Once found, the display shows Channel updated. 3 Press the Menu Select button below Exit to return to Home screen. The Home screen shows . If the channel deleted is the Home channel, the Home screen shows +”Blank”. If the radio is triggered to search for an empty entry, the display shows Invalid entry. If the entry does not match, the display shows Channel name not found. Repeat from step 4 or 5 to search again.
• • • Call Type (Icon) WACN ID (Astro 25 Trunking IDs only) System ID Note: Your radio must be preprogrammed to allow you to add, edit, or delete the contact entries. The entries are alphabetically sorted. 2 Advanced Features The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You hear the Menu Inactive Exit Tone upon feature exit.
If there is no voice activity for a preprogrammed period of time, the call ends. 5 If the call reaches the maximum ring time, the call ends. or to [Add Number] and press the Menu Select button directly below Sel. 6 or to Number 1 and press the Menu Select button directly below Edit. The display shows Edit Number 1 and a blinking cursor appears. Adding a New Contact Entry 1 or to Cnts and press the Menu Select button directly below Cnts. The entries are alphabetically sorted.
• • Repeat Steps 6 through 7 to enter or edit the exisitng system IDs. Repeat Steps 5 through 7 to add a new number. 9 Press the Menu Select button directly below Done once you have finished. The display shows Stored, confirming that the contact entry has been added. 4 Select the Menu Select button directly below Yes to delete the entry, or No to cancel and return to the main screen of Contacts. The display shows deleted and the radio returns to the main screen of Contacts.
The radio returns to the main display of Contacts. 2 3 Methods of Contact Editing in a Call List Editing an Entry Alias 1 or to Cnts and press the Menu Select button directly below Cnts. The entries are alphabetically sorted. or to Cnts and press the Menu Select button directly below Cnts. The entries are alphabetically sorted. 2 or to the entry you want to delete and press the Menu Select button directly below Optn.
Advanced Features 6 Press the Menu Select button directly below Done to save your changes and return to the main screen of Contacts. 6 Press the Menu Select button directly below Done to save your changes and return to the main screen of Contacts. Editing as Entry ID Editing a Call Type 1 or to Cnts and press the Menu Select button directly below Cnts. The entries are alphabetically sorted. 1 or to Cnts and press the Menu Select button directly below Cnts. The entries are alphabetically sorted.
Viewing Details of a Contact 1 or to Cnts and press the Menu Select button directly below Cnts. The entries are alphabetically sorted. 2 or to the entry you want to view and press the Menu Select button directly below Optn. 3 or to View and press the Menu Select button directly below Sel. The display shows all the numbers associated with the entry. Scan Lists Scan lists are created and assigned to individual channels/ groups.
• • • Long press the preprogrammed Scan List Programming button (side button). Move the preprogrammed Scan List Programming switch to programming position. or to ScnL then press the Menu Select button directly below ScnL. The display shows the lists that can be changed. 2 or to the entry you want to edit. • • 5 Perform one of the following actions: • Move the Scan List Programming switch out of programming position. • Press to exit scan list programming and return to the Home screen.
or to the member you want to edit. • 3 Perform one of the following actions: • • Press the Select button once to add the currently displayed channel to the scan list. Press the Select button one or more times to change the scan list status icon of the currently displayed channel. 4 Perform one of the following actions: • • • or to select more list members whose scan status you want to change. Use the keypad to go directly to that scan list member.
Making a Dynamic Priority Change (Conventional Scan Only) Scan This feature allows you to monitor traffic on different channels by scanning a preprogrammed list of channels. Turning Scan On or Off Perform one of the following actions: • • Advanced Features • Press the preprogrammed Scan button to toggle Scan On or Scan Off to initiate or stop scan. Turn the preprogrammed Scan switch to the Scan on or Scan off position to initiate or stop scan.
When the radio is locked onto the channel to be deleted, perform one of the following actions: • Press the preprogrammed Nuisance Delete button. • or to Nuis and press the Menu Select button directly below Nuis. The radio continues scanning the remaining channels in the list. Restoring a Nuisance Channel To restore the deleted nuisance channel, perform one of the following actions: • • • Stop and restart a scan. Mode change to another channel and back to the original channel.
See Making a Talkgroup Call on page 62 or Making a Private Call (Trunking Only) on page 62 for more information on returning the call. If the call alert page is sent successfully, you hear a tone and the display shows Ack received. The radio returns to the Home screen. Sending a Call Alert Page If the call alert page is not acknowledged, you hear a low tone and the display shows No acknowledge. Press the Menu Select button directly below Ok to return to the main screen for Contacts.
If the call alert page is not acknowledged, you hear a low tone and the display shows No acknowledge. Press the Menu Select button directly below Ok to return to the main screen of Contacts. Sending a call alert page via the radio menu Call: a) or to Call. Quick Call II (ASTRO P25 Digital Trunking and Conventional) b) Press the Menu Select button directly below Call. c) or to select the alias or ID, and press the PTT button to initiate the call.
sound the selected tone and also to sound a preconfigured alert tone after the selected tone has sound. Initiating a Quick Call II Transmission The Emergency feature is used to indicate a critical situation. The broadcasting or transmitting radio must be preprogrammed to see the tone in the Quick Call II tone list. The receiving radio must also be preprogrammed to decode the tone to broadcast.
The radio operates in the normal dispatch manner while in Emergency Call, except if enabled, it returns to one of the following: Tactical/NonRevert The radio sends emergency alarm and/or make emergency call on the current selected channel. Non-Tactical/ Revert for Conventional system The radio reverts to the preprogrammed emergency channel to send alarm and/or make emergency call.
the alarm ends, and the radio exits the Emergency Alarm mode. If no acknowledgement is received, the display shows No acknowledge. The alarm ends when the timer expires and the radio exits the Emergency Alarm mode. Sending an Emergency Call (Trunking Only) This feature gives your radio priority access to a talkgroup. 1 Press the preprogrammed Emergency button. One of the following scenarios occurs: Advanced Features • • The display shows Emergency on the current zone and channel.
• You receive no acknowledgement. The display shows No acknowledge. You press the PTT button while in the Emergency Alarm mode. If unsuccessful, you hear the radio sounds a short low-pitched tone to indicate the selected channel does not support emergency and rejects to launch emergency mode. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.
• Emergency operation. The emergency alarm or call continues on the new channel. If the new channel is not preprogrammed for Emergency, the display shows No emergency, and you hear an invalid tone until you exit the Emergency state or change to a channel preprogrammed for Emergency. Emergency Keep-Alive Feature This feature, when enabled, prevents the radio from being turned off via the On/Off Control Knob when the radio is in the Emergency state.
The Man Down feature provides a Clear function to the user. After a Man Down condition has been detected, the user can press a preprogrammed Clear button or preprogrammed Menu Select button to cancel the Man Down condition. The radio remains in the Man Down state without triggering an emergency condition until the radio is moved out of the Man Down state, at which point Man Down functionality resumes.
When the radio is programmed with Man Down feature, special care is required when charging the radio with a wall mounted charger. See Proper Ways to Handle the Radio on page 185 for details. Pre-Alert Timer This timer sets the amount of time that a Man Down condition must be present before the radio-user is warned of the Man Down condition. When the radio detects that it has returned to the vertical position or when the radio detects motion, the Pre-Alert timer stops and is reset.
and visual alert associated with the emergency feature. If the radio is programmed in Surveillance Mode, the alert tone can be heard from the radio speaker. Radio Alerts When Man Down Enhanced is Triggered Note: This feature is to be preprogrammed specifically to a zone and channel which supports Emergency feature. The volume and repetition duration of Man Down Enhanced alert tone could be customized and preprogrammed to suite the required situation.
emergency from going off with the following operation. Perform one of the following actions: • • • Repositioning the radio or shaking the radio (when motion sensitivity is enabled). Press the preprogrammed Man Down Clear button to exit. Press the Menu Select button below Clr to exit. 1 Turn the radio on and place in the vertical position, for at least 5 seconds. 2 Lay the radio down in the horizontal position. 3 Wait for alert tone.
• • ARS Server Mode (default mode) ARS Non-Server Mode Note: The default ARS mode can be changed by a qualified radio technician using the radio’s programming software. Selecting or Changing the ARS Mode The following methods are options on how to select or change the ARS Mode. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
Note: A predefined username that is set more than the maximum allowed characters is an invalid name. Logging In as a User 1 Perform one of the following actions: • • Press the preprogrammed User Login button. or to User and press the Menu Select button directly below User. The display shows the User Login screen. 2 Perform one of the following actions: Advanced Features • • 96 English or to [ID Entry] and press the Menu Select button directly below Edit to enter ID.
• • If the user name is invalid, login fails and the user login failure indicator (IP indicator) icon blinks. The display also shows momentary Login failed. If the PIN is invalid, login fails and the user login failure indicator (IP indicator) icon blinks. The display also shows momentary Login failed. Wait for the logged in confirmation screen. If the login process is successful, the display shows the successful user login indicator (IP indicator) icon and Logged in, with Logt and Exit.
• • • A predefined message (quick text message). An edited quick text message. A query (ASTRO 25 Advanced Messaging Solution). Note: Query is only supported within ASTRO 25 Advanced Messaging Solution. See TwoFactor Authentication on page 109 and ASTRO 25 Advanced Messaging Solution on page 108 for details.
During the uppercase and lowercase mode, multitapping the keys only scrolls through the letters. For example, A->B->C, a->b->c. During the numeric mode, except for , pressing the keypad only enters the numeric digits. Subsequent presses of the same key inserts the same digit to the text message (no multi-tap). 6 Press the Menu Select button directly below Optn once the message is composed. 7 or to Send Message and press the Menu Select button directly below Sel.
If the message is not sent, you hear a low tone, the display shows Send failed and returns to the main TMS screen. • Note: You can append a priority status and/or a request reply to your message. See Priority Status and Request Reply of a New Text Message on page 101 for more information. • You can also select the Save to Drafts option to save your message in the Drafts folder to send it at a later time. See Accessing the Drafts Folder on page 106 for more information.
7 or to Send Message and press the Menu Select button directly below Sel. 8 Perform one of the following actions: • • or to scroll through the address list and highlight the required address. or to [Other Recpnt] and press the Menu Select button below Edit. When a blinking cursor appears on the Enter Address screen. Use the keypad to type the address entry. 9 Press the Menu Select button directly below Send or press the PTT button to send the message.
1 Press the Menu Select button directly below Optn. 2 or to Mark Important and press the Menu Select button directly below Sel to indicate the message is important. The priority status icon appears beside the normal message icon on the label bar. Removing a Priority Status from a Text Message Ensure there is an outgoing message composed to allow you to perform this procedure. See Composing and Sending a New Text Message on page 99 for more information.
Ensure that an outgoing message is composed to allow you to perform this procedure. See Composing and Sending a New Text Message on page 99 for more information. 1 Press the Menu Select button directly below Optn. 2 3 or to Mark Important and press the Menu Select button directly below Sel to indicate the message is important. or to Req Reply and press the Menu Select button directly below Sel to request for a reply.
same. You can use the options interchangeably depending on your preference and the programmed functions. • Advanced Features • Receiving a text message via the Data Feature button or the TMS Feature button: a) When you receive a message, press and hold the preprogrammed Data Feature button or the TMS Feature button to access the Inbox. The display shows a list of aliases or IDs, with the sender of the latest received message on top.
• Select Optn to configure the message settings. Select Del to delete the message. Select Back to return to the previous screen. • Note: The icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) Indicators on page 45 for more information. 1 or to the required aliases or ID and press the Menu Select button below Sel to view the message. 2 Press the Menu Select button directly below Rply to reply to a message.
Note: Press the Menu Select button directly below Back at any time to return to the previous screen. You can append a priority status and/or a request reply to your message. See Priority Status and Request Reply of a New Text Message on page 101 for more information. Accessing the Drafts Folder This folder stores the messages that were saved previously. The Drafts folder can hold up to 10 messages. The oldest draft in the folder is deleted when the 11th message comes in. Advanced Features 1 or to TMS.
2 3 or to TMS and press the Menu Select button directly below TMS to access the TMS feature screen. or to Sent and press the Menu Select button below Sel. The display shows a list of aliases or IDs, with the recipient of latest sent message on top. or to the required aliases or ID and press the Menu Select button below Sel to view the message. While on the view message screen, press the Menu Select button directly below Optn, Del or Back to access the option.
You can append a priority status and/or a request reply to your message. See Priority Status and Request Reply of a New Text Message on page 101 for more information. Deleting a Text Message 1 From the Inbox, Draft, or Sent screen, scroll through the messages. to Deleting All Text Messages Advanced Features 1 Perform one of the following actions: 108 English 3 Perform one of the following actions: • • or 2 Press the Menu Select button directly below Del to delete the current message.
With this Advanced Messaging Solution, ARS functionality splits between two protocols: • • ARS for Device Registration New User Authentication for User Login TMS functionality splits between two protocols: • • TMS for messaging New Service Advertisement for service availabilities The radio with Two-Factor capabilities are backward compatible with the existing device registration system and TMS servers.
so the message is delivered to the user, not to the radio which may have any user using it at the time. Secondly, this feature supports query authentication requirements so the query service knows which user originated a query. You can still send text messages without logging in as a user. The user login feature only enables the recipient of your message to identify you as the sender by assigning a username to your message.
• or to scroll through the list of predefined Unit IDs. Press the Menu Select button directly below Sel to select the predefined Unit ID. or to scroll through the Press and hold list of predefined Unit IDs at a fast scroll rate. Press the Menu Select button directly below Sel to select the predefined Unit ID. If the selected predefined Unit ID has more than the maximum allowed characters, or an invalid character in it, the display shows momentary Invalid UnitID.
1 Press the Menu Select button directly below Logt. One of the following scenarios occurs: • • successfully logged in the radio with a Two-Factor Authentication. Note: The query server must be selected as the destination so that it can receive the query message and respond the query with text message. The query server must be an entry in the data user list in the CPS. The display shows Clear private data?.
5 or to Query and press the Menu Select button directly below Sel for a predefined message. or to scroll through the list of messages and press the Menu Select button directly below Sel to select the required message. The message appears on the Compose screen, with a blinking cursor at the end of it. 6 Use the keypad to edit the message, if required. 7 Press the Menu Select button directly below Optn. 8 or to Send Message and press the Menu Select button directly below Sel.
icon flagged with “Priority”. The display shows momentary New msg. To access the Inbox, press and hold the Data Feature button or the preprogrammed TMS Feature button or press the Menu Select button directly below TMS. The display shows a list of aliases or IDs, with the sender of the latest received message on top. Secure Operations Secure radio operation provides the highest commercially available level of voice security on both trunked and conventional channels.
The radio does not transmit until you set the Secure/ Clear switch to the secure position. You can request to configure the radio to ignore the clear voice or insecured transmission when the radio is in secured transmission. Check with your agent for details. If the “Ignore Secure/Clear Switch when Strapped” programming option is enabled, the radio transmits without displaying any messages in the strapped mode of operation, regardless of the Secure/Clear switch setting.
Multikey Feature This feature allows the radio to be equipped with different encryption keys and supports the DES-OFB algorithm. have operator-selectable key erasure. Selecting an Encryption Key 1 Conventional Multikey 2 Press the Menu Select button directly below Key. The display shows the last user-selected and stored encryption key, and the available menu selections.
When the selected key is not allowed, you hear a momentary illegal key tone and the display shows Illegal key. Selecting a Keyset This feature allows you to select one or more groups of several encryption keys from among the available keys stored in the radio. The display shows the last user-selected and stored keyset, and the available keyset menu selections. 2 or to scroll through the keysets or use the keypad to enter the number of the desired keyset.
• Erasing the selected encryption keys via the radio menu: a) or to Eras and press the Menu Select b) c) Advanced Features d) e) • 118 English button directly below Eras. The display shows the last user-selected and stored encryption key, and the available menu selections. or to the desired encryption key or use the keypad to enter the number of the desired key. Press the Menu Select button directly below Optn. The display shows the available key erase options.
1 or to Reky. 2 Press the Menu Select button directly below Reky. 3 Perform one of the following actions: • Press the PTT button to send the rekey request. • or Press the PTT button again, or the Emergency button, to exit the feature and transmit in normal mode. If the rekey operation fails, you hear a bad-key tone and the display shows Rekey fail. Note: The rekey operation failure indicates that your radio does not contain the Unique Shadow Key (USK).
Hear Clear Note: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. Random FM Noise Canceller (Flutter Fighter) There are two components of Hear Clear. Companding Reduces the channel noise, e.g. OTA transmission, that is predominantly present in UHF2 and 900 MHz channel with the following features. Advanced Features Compressor Reduces the background noise flow and the speech signal at transmitting radio.
Clear radios – 0 to 8 characters. 2 Perform one of the following actions: • • • Press the Menu Select button directly below Sel to enter the code. Press the Menu Select button directly below Del to delete any unwanted characters. Press the Menu Select button directly below Cncl to exit the feature. If the password is correct, the radio unlocks. Changing Your Password 1 or to Pswd. 2 Press the Menu Select button directly below Pswd. The display shows Change Password screen.
The password is updated. 8 Press the Menu Select button directly below Sel. If the two passwords do not match, repeat Steps 5 through 10. 9 Re-enter the new password. Note: If you enter three incorrect old passwords, the radio exits the password feature. You cannot access this feature again until you turn the radio off and on. 10 Press the Menu Select button directly below Sel. The password is updated. If the two passwords do not match, repeat Steps 5 through 10.
• • The display shows Pswd enabled, indicating that the radio lock feature is enabled. The display shows Pswd disabled, indicating that the radio lock feature is disabled. Radio Stun and Kill Radio Stun This feature allows you to stun another radio by sending an over the air command using the menu on your radio. This feature prevents an unauthorized user from using the radio. Once the radio is stunned, a password is required to re-activate the stunned radio. Using Radio Stun 1 or to Stun.
Radio Kill This feature allows you to render your radio or another radio inoperable if the radio is misplaced or lost. When a radio is killed, the display turns blank and all functions of the radio are not usable. Advanced Features The killed radio can only be recovered from KILL with a special device. Consult an authorized and qualified technician for details. 5 Perform one of the following actions: • • • • or to the required ID.
Global Positioning System / Global Navigation Satellite System The Global Navigation Satellite System (GNSS) in the radio uses information from the Global Positioning System (GPS) to determine the approximate geographical location of your radio. The geographical location is expressed as latitude and longitude or Military Grid Reference System (MGRS) format per request from customers.
• In temperature extremes outside the operating limits of your radio Even where location information can be calculated in such situations, it may take longer to do so, and your location estimate may not be as accurate. Therefore, in any emergency situation, always report your location to your dispatcher.
Note: The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You hear the Menu Inactive Exit Tone upon feature exit. The following table shows the differences between programmable waypoints and preprogrammed waypoints. Programmable Waypoints Preprogrammed Waypoints User-configurable location coordinates.
The display shows Location off. 3 Perform one of the following actions: • • To obtain a location fix, press the Menu Select button directly below On . Press the Menu Select button directly below or to Turn On GPS and press the Optn. Menu Select button directly below Sel. The front display shows the MGRS or latitude/ longitude location, time, and date of the last successful location fix. Advanced Features 4 To obtain a new location fix, press the Menu Select button directly below Rfsh.
4 Press the Menu Select button directly below Ok once you are done. One of the following scenarios occur: • • • The display shows Current loc saved as . The display shows Current loc saved as [Home]. The display shows Current loc saved as [Destination]. 5 To return to the Home screen, press , the PTT button, the preprogrammed GPS button or the Menu Select button directly below Exit. Viewing a Saved Waypoint Ensure your radio shows the current location on the screen.
1 Press the Menu Select button directly below Optn. 2 3 4 or to Waypoints and press the Menu Select button directly below Sel. The display shows a list of waypoints. or to the required saved waypoint, and press the Menu Select button directly below Optn. or to Edit name and press the Menu Select button directly below Sel. A blinking cursor appears in the Edit Name screen. Advanced Features 5 Use the keypad to edit the alias.
4 • or to [Destination] and press the Menu Select button directly below Optn. or to Edit location and press the Menu Select button directly below Sel. The first number blinks. 5 Utilize the following control buttons to select the number/coordinates if required, then press the Menu Select button directly below Edit to change the number/coordinates. • Press to move to the previous number/ coordinates. • Press to move to the next number/ coordinates.
3 Perform one of the following actions: • • or to the required saved waypoint, and press the Menu Select button directly below or to Edit name and press the Optn. Menu Select button directly below Del. Press the Menu Select button directly below Del. 4 The display shows Delete Confirm?. Advanced Features 5 Press the Menu Select button directly below Yes to delete the waypoint or press the Menu Select button directly below No to return to the Waypoints main screen.
2 3 or to Dist frm here and press the Menu Select button directly below Sel. The display shows a list of waypoints. or to the required waypoint and press the Menu Select button directly below Sel. The display shows the distance and bearing from the current to the selected coordinates.
Upon receiving a voice transmission with GPS coordinates enabled on the receiving radio, the display shows the coordinates available in full or in short coordinates. There are two different formats available. Refer to the following list for the details shown in the Peer-Location quick text. Consult your agent to pick the best format to configure to your radio. Full location coordinates Advanced Features Short location coordinates • • • PTT ID (This is optional.
Note: If the radio is set up in DVRS, only mobile radio is supported for this feature. Entering the Geofence Area The Voice Announcement and TMS display in this feature are optional. They must be configured to enable you to hear and see these indicators. When the radio enters a Geofence area, the radio immediately sends a message ACK back to the system.
The following procedure guides you to exit the text message received. Press the Menu Select button below Exit or to return to Home screen. The other operations are the same as normal dynamic regroup command. Advanced Features When the radio exits the Geofence area, your radio reverts to original channel or newly assigned talkgroup. The radio display shows the new channel together with Voice Announcement to indicate the changes.
If the zone controller loses communication with any site, that site reverts to site trunking. The display shows the currently selected zone/ channel combination and Site trunking. Note: When this occurs, you can communicate only with other radios within your trunking site. 2 Press the Menu Select button directly below Site. 3 Perform one of the following actions: • • Locking and Unlocking a Site This feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites.
• Note: or to RSSI and press the Menu Select button directly below RSSI. It is recommended to use Motorola proprietary Mission Critical Wireless (MCW) devices with APX radios during Mission Critical operations as other Bluetooth® devices may or may not meet the mission critical standard. The display shows momentary the name of the current site and its corresponding received signal strength indicator (RSSI). Changing the Current Site Your radio must be preprogrammed to allow you to use this feature.
You hear a short, medium-pitched tone. The display shows momentary Bluetooth on, and The following methods are options on how to turn on the Bluetooth. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions. • Turning on the Bluetooth via the radio menu BT: a) or to BT. To access the Bluetooth feature screen, press the Menu Select button directly below BT.
• Turning off the Bluetooth via the preprogrammed button: a) Press the preprogrammed button to turn off the Bluetooth. You hear a short, medium-pitched tone. The display shows momentary Bluetooth off and disappears. Re-Pair Timer Advanced Features There are two options for configuring the Bluetooth pairing type of the radio. The type defines the duration the radio and the accessory retain the pairing information. 140 English Immediate (For MCW accessories only.
Re-Pair Timer Scenarios Infinite (For all • Bluetooth devices) When the radio is powered off, the accessory attempts to re-establish the Bluetooth Connection for a period of time depending upon the Drop Timer value. If the device fails to reconnect within the period, the accessory then powers off. Bluetooth Drop Timer The Bluetooth Drop Timer has two different settings and functions, depending upon the selection of the Re-Pair Timer.
The radio could not control the Drop Timer of Personal Area Networking (PAN), Dial-Up Networking (DUN), Commercial Off- The-Shelf (COTS) and data services. It depends on the specifications of these external devices. Check with your dealer or system administrator for more information about these timers. To establish the Bluetooth Connection, see Pairing with Low Frequency-Motorola Proximity Pairing (LFMPP) Feature on page 142 or Standard Pairing Feature on page 143 .
The radio tries to establish connection with the device once paired. Note: If the connection fails within 6 seconds, you hear a decremental-pitched tone to indicate that the device is unpaired. The display shows unpaired. Repeat this step to re-initiate the pairing process. If the connection is successful, you hear an incremental-pitched tone. The display shows connected and the Bluetooth icon turns from to .
technician. Check with your dealer or system administrator for more information. Once a COTS headset is paired to your radio, it is always connected. Therefore the battery life of the accessory is aligned with the Talk time power consumption, not the Standby time consumption. The Bluetooth Standard Pairing feature enables your Bluetooth enabled radio to search for other Bluetooth enabled and discoverable device.
If the feature fails to initiate, the radio sounds a short, low-pitched tone. The screen shows BT Search failed. Press the Menu Select button below Back to return to Bluetooth feature screen, or press or the Menu Select button below Exit to return to Home screen. Turning Bluetooth visibility to on enables other Bluetooth devices to search for your radio. The visibility of the Bluetooth is set to off by default. The following methods are options on how to turn on Bluetooth visibility.
Receiving Pairing Request from other Devices When the timer expires, the status changes to Visibility off failed. Repeat this step to turn off Bluetooth visibility. c) To return to the Home screen, press the Menu Select button directly below Exit. When your radio receives a pairing request from other device, the display shows pair request. Press the Menu Select button below Ok to accept or Cncl to refuse pairing request.
1 When the radio display shows pair request, perform one of the following actions: • • 2 Perform one of the following actions when the display shows Compare PIN: XXXXXX.: • • To accept, press the Menu Select button below Ok. To reject, press the Menu Select button below Cncl Your radio only supports HSP, DUN, PAN and SPP Bluetooth profiles. When the pairing timer expires, the display shows pair canceled and return to Home screen.
• The display shows connect failed (if the connecting timer expires). If the PIN is correct but the profiles are not supported, the display shows BT profiles not supported. The display returns to Home screen. Pairing the Authentication PIN with the Generated Numeric PIN Follow the procedure inSearching and Pairing the Bluetooth Device on page 144 to search for available Bluetooth devices. Start pairing with the Authentication PIN by following the steps described next.
Follow the procedure in Searching and Pairing the Bluetooth Device on page 144 to search for available Bluetooth devices. Start pairing with the Authentication PIN by following the steps described next. 1 or to the required device. Press the Menu Select button directly below Sel to initiate pairing. Your radio only supports HSP, DUN, PAN and SPP Bluetooth profiles. If successful, the display shows Pairing in progress... followed by a request for PIN number. A blinking cursor appears below the Enter PIN:.
depending on your preference and the programmed functions. • Turning on the Bluetooth audio via radio menu BT: a) or to BT. Press the Menu Select button the same. You can use the options interchangeably depending on your preference and the programmed functions. • directly below BT to access the Bluetooth feature screen. b) or to Bluetooth spkr and press the Menu Select button directly below On. The display shows On. c) To return to the Home screen, press the Menu Select button directly below Exit.
Adjust volume up/down on the Bluetooth audio device. The radio display shows Volume XX, and you hear a short, medium-pitched tone. Viewing and Clearing the Bluetooth Device Information 1 2 or to BT. Press the Menu Select button directly below BT to access the Bluetooth feature screen. or to Devices. Once the display highlights the Devices, the display shows XX connected alternates with XX paired. 3 Press the Menu Select button directly below Sel.
If unsuccessful, you hear the radio sounds a short, low-pitched tone. The display shows Clear all BT devices failed. The display returns to Bluetooth feature screen. shows clear failed. The display returns to previous screen. Note: If Re-Pair Timer is set to infinite and you clear keys on the radio, you must clear keys on all previously paired devices as well. (Please see your accessories manual for further details.
Editing the Bluetooth Friendly Name Your radio must be preprogrammed to allow you to use this feature. 1 or to BT. Press the Menu Select button directly below BT to access the Bluetooth feature screen. 2 or to Friendly name and press the Menu Select button directly below Edit. A blinking cursor appears in the Friendly Name screen. 3 Use the keypad to edit the text.
Responding to the Notification of Upgrade 1 The display shows Upgrade? and two short, medium- pitched tones sounds every 30 seconds until the user makes a choice of accepting, delaying, or rejecting the request 2 Perform one of the following actions: • • • Press the Menu Select button below Acpt to accept the request to upgrade immediately. Press the Menu Select button below Dlay to delay the request to upgrade. Press the Menu Select button below Rej to reject the request to upgrade.
announces the current zone and channel it is transmitting. Note: Pressing this preprogrammed playback button enables the voice feature to announce in High priority. Note: This feature must be preprogrammed by a qualified radio technician. Check with your agent if Voice Announcement is available for the feature you need. • The two options of priority for the Voice Announcement available are: • High Enables the voice of the feature to announce even when the radio is receiving calls.
special situation that they need to be aware of. Only authorized radios are enabled to send SSA. Upon the activation of a SSA, the receiving radios display the alert alias and generate the periodic alert tone. Note: Alert alias, alert tone, and alert period can be preprogrammed. Alert period is the duration for the radio to repeat the alert tone. An interval of 5 seconds might impact the battery life of the radio. Check with your dealer or system administrator for more details.
Sending SSA Notification to Single Site Via Manual Entry 1 or to SSA. 2 Press the Menu Select button directly below SSA. The display shows the Site Alert screen. 3 4 or to Start Alert and press the Menu Select button directly below Sel. The display shows the Select Site screen. or to [SiteID Entry] to send alert via manual entry. Press the Menu Select button directly below Edit. The display shows the Enter SiteID screen. 5 Key in the desired Site ID and press the Menu Select button directly below Ok.
Sending SSA Notification to All Sites 1 or to SSA. 2 Press the Menu Select button directly below SSA. The display shows the Site Alert screen. 3 or to Start Alert and press the Menu Select button directly below Sel. The display shows the Select Site screen. 6 To return to the Home screen, press the Menu Select button directly below Exit. If you are at the site designated to receive this alert, you can hear an alert tone repeated periodically.
The display shows Sending req. If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows Req failed. If the request is successful, the display shows Req successful. If the request is successful, the display shows Req successful. 6 To return to the Home screen, press the Menu Select button directly below Exit. If you are at the site designated to receive this alert, you can hear an alert tone repeated periodically.
3 4 or to Stop Alert and press the Menu Select button directly below Sel. The display shows the Select Site screen. or to [SiteID Entry] and press the Menu Select button directly below Edit. The display shows the Enter SiteID screen. 5 Key in the required Site ID and press the Menu Select button directly below Send. The SSA Alert for the designated site stops. Stopping SSA Notification of All Sites 1 2 Press the Menu Select button directly below SSA. The display shows the Site Alert screen.
5 To return to the Home screen, press the Menu Select button directly below Exit. The SSA Alert for all sites stop. The SSA Alert for all available sites stop. Stopping SSA Notification of All Available Sites 1 or to SSA. Utilities Viewing Recent Calls 2 Press the Menu Select button directly below SSA. The display shows the Site Alert screen.
You can use the options interchangeably depending on your preference and the programmed functions. • • Viewing recent calls via the preprogrammed Recent Calls button: a) Press the preprogrammed Recent Calls button. b) or to scroll through the list. c) To return to the Home screen, press the Menu Select button directly below Exit, press or the PTT button. Viewing recent calls via the radio menu: a) or to Rcnt.
Note: See the Basic Zone Bank 1 and Basic Zone Bank 2 icons for more information on the status icons. Selecting an Enhanced Zone Bank This feature is created in order to allow users to communicate in more zones. An Enhanced Zone Bank (EZB) consists of three zones. This also means each icon A, B, C, ... or Y consist of three zones. You can use the preprogrammed 3-position A-B-C switch to select the first, second or third zone in an EZB. This feature allows user to navigate from up to 75 zones in 25 EZBs.
The following methods are options on how to select the power level. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions. • Selecting the Power Level via the Transmit Power Level switch: a) Use the preprogrammed Transmit Power Level switch to toggle the power level between low and high power. • Selecting the Power Level via the radio menu: a) or to Pwr.
• the display shows momentary Radio ID on, and the radio alias appears on the Home screen. Selecting the Audio Speaker Selecting a radio profile via the radio menu: a) or to Prfl and press the Menu Select Your radio must be preprogrammed to allow you to use this feature. button directly below Prfl to access the Profiles feature screen. b) or to scroll through the menu selections.
depending on your preference and the programmed functions. • Advanced Features • Select the audio speaker via the preprogrammed Profile button: a) Press the preprogrammed Profile button. b) or to scroll through the menu selections. c) Press the Menu Select button directly below Sel to select the radio profile with the required speaker routing or press the Menu Select button directly below Exit to exit the screen without making any changes. The radio returns to the Home screen.
Perform one of the following actions: • • To toggle the backlight on or off, press the preprogrammed Light/Flip button. To turn the backlight on, press any key of the keypad, the Menu Select or Navigation button, or any programmable radio controls or buttons. the NVG to operate in non-NVG compatible display mode might injure your eyes. Accessory connected to the radio that is in NVG display mode such as Display Remote Speaker Microphone (DRSM) has its backlight always in off state.
c) To select the required radio profile, press the Menu Select button directly below Sel or to exit the screen without making any changes, press the Menu Select button directly below Exit. The radio returns to the Home screen with NVG display mode. The profile name on the Home screen indicates the current selected radio profile. Advanced Features • 168 English Setting up the radio display and visual indicators via the radio menu Prfl: a) or to Prfl.
Turning Voice Mute On or Off You can enable and disable voice transmission, if needed. The following methods are options on how to turn Voice Mute on or off. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions. • • Turning Voice Mute off or on via the preprogrammed Voice Mute button: a) To turn the feature off or on, press the preprogrammed Voice Mute button.
You hear a short, low-pitched warning tone, the transmission is cut-off, and the LED goes out until you release the PTT button. 2 Release the PTT button. The timer resets. 3 To re-transmit, press the PTT button. The time-out timer restarts and the LED lights up solid red. Time and Date Setup You can set the time and date for your radio. Settings: Advanced Features • • • 170 English The default time setting is a 12-hour clock. The display shows 12:00AM.
Press the Menu Select button directly below Cncl to discard all changes and return to the Home screen. Press at any time to return to the Home screen without saving your changes. Note: If a call arrives while the radio is in the clock-setting menu, the radio exits clock setting and displays the call information. Any changes made before the call is not saved.
channel. The radio also unmutes to any digital activity on a digital channel. Place the preprogrammed PL Defeat switch in the PL Defeat position. One of the following scenarios occurs: Smart PTT is a per-personality, programmable feature used in conventional radio systems to keep radio users from talking over other radio conversations. • • You hear any activity on the channel. The radio is muted if no activity is present. When smart PTT is enabled in your radio, you cannot transmit on an active channel.
Description code is the same as yours, the transmission is not prevented. Quick-Key Over- Your radio must be preprogramride med to allow you to use QuickKey Override. This feature can work in conjunction with either of the two above variations. You can override the transmit-inhibit state by quick-keying the radio. In other words, two PTT button presses within the preprogrammed time limit.
Note: If the user has disabled TX Inhibit via the menu and then moves the switch to the position where TX Inhibit is enabled, the new value overwrites the menu value. The display shows Tx inhibit on. You hear a sequence of short, low‐high tones to indicate transmission is inhibited. Pressing PTT triggers the radio sounds a constant short, low‐pitched tone (reject tone). Note: The status of the Transmit Inhibit does not change after the radio powers up.
Accessing the Radio Information 1 This feature displays the following radio information: or to Batt. 2 Press the Menu Select button directly below Batt. The display shows the details of the battery. 3 To return to the Home screen, press the Menu Select button directly below Exit.
Note: To return to the Home screen, press time. 1 Perform one of the following actions: • • 2 Press the preprogrammed Info button. 3 Perform one of the following actions: Advanced Features • • or to scroll through the various information. To return to the previous screen, press the Menu Select button directly below Back. Press to return to the Home screen . Viewing the IP Information This feature displays the device name, IP address, and status of your radio.
1 Perform one of the following actions: • • 1 Perform one of the following actions: • • 2 Press the preprogrammed Info button. or to Info and press the Menu Select button directly below Info. or to Control map and press the Menu Select button directly below Sel. The display shows the Control Map screen. 3 Perform one of the following actions: • • • or to scroll through the various information. Press the Menu Select button directly below Back to return to the previous screen.
Advanced Features • 178 English Press the Menu Select button directly below Cncl to return to the previous screen.
Radio Care Caution: • • Your radio casting has a vent port that allows for pressure equalization in the radio. Never poke this vent with any objects, such as needles, tweezers, or screwdrivers.This could create leak paths into the radio and the radio’s submergibility will be lost. • A • Your radio is designed to be submerged to a maximum depth of 6 feet, with a maximum submersion time of 2 hours. Exceeding either maximum limit may result in damage to the radio.
• Otherwise, the water will decrease the audio quality of the radio. Do not disassemble the radio. This could damage radio seals and result in leak paths into the radio. Any radio maintenance should be performed only by a qualified radio technician. Cleaning Your Radio Caution: Do not use solvents to clean your radio as most chemicals may permanently damage the radio housing and textures. Do not submerge the radio in the detergent solution.
Helpful Tips Washing The Radio 1 Submerge the radio (with battery attached) completely into the tap water while shaking it for approximately 20 seconds. 3 Dip the radio completely into the detergent solution and repeat turning action for both knobs, 3-Position A/B/C and the Secure Switch. 2 Remove the radio from the water and perform the following. Turn the frequency knob all the way from position 1 to 15 and back to position 1 twice.
4 Lightly scrub the plastic area (front, back, bottom, top and side planes) of the radio with the small brush.Take extra care around the Speaker Grill and Microphone port openings. 6 Submerge the radio into tap water and shake it to remove the detergent. Helpful Tips 5 Use the toothbrush to lightly brush the gaps at the base of the knobs and around the switches. Take extra care around the Speaker Grill and Microphone port openings.
Helpful Tips Washing the Battery 1 Rinse the battery under running water to remove any excess debris. 8 Shake off excess water and pat dry the radio with a dry towel. Take extra care to tap/shake out any trapped water from the speaker grill area. 2 Using the small brush dipped in the detergent solution, lightly scrub the front, botom and sides of the battery. 3 Use the toothbrush to brush the back and top of the battery. Exercise caution to avoid scratching the battery contacts.
5 Rinse the battery under running water to remove any excess detergent. Washing the Universal Connector Cover Helpful Tips 1 Dip the universal connector cover into tap water followed by the detergent solution. 184 English 2 Use your thumb or finger to lightly rub clean the rubber seal.
• • • • • 4 Rinse the cover under running waer to wash off the detergent. 5 Pat dry with a towel. Proper Ways to Handle the Radio • Do not pound, drop, or throw the radio unnecessarily. Never carry the radio by the antenna. Avoid subjecting the radio to an excess of liquids. Do not submerge the radio unless it is a ruggedized. Avoid subjecting the radio to corrosives, solvents or chemicals. Do not disassemble the radio.
on a contract basis. For a contract service agreement, please contact your nearest Motorola service or sales representative, or an authorized Motorola dealer. Battery Care Battery Charge Status Fuel Gauge Icons A blinking fuel gauge icon ( ) is displayed only when the battery voltage drops to low level. In this case, replace the battery with a fully charged one. Gauge Your radio can indicate the battery’s charge status through: • • the LED and sounds. the fuel gauge icon on the display.
Helpful Tips Gauge Battery Charge Battery Recycling and Disposal Top Display: 11% to 25%[3] In the U.S. and Canada, Motorola participates in the nationwide Rechargeable Battery Recycling Corporation (RBRC) program for battery collection and recycling. Many retailers and dealers participate in this program. For the location of the drop-off facility closest to you, access RBRC's Internet web site at www.rbrc.com or call 1-800-8-BATTERY.
Accessories The accessory link below is for APX radios. Not all accessories are FCC certified to operate with all APX models and/or bandsplits. Please refer to the specific APX radio price pages for a list of FCC certified accessories or contact your sales representative for accessory compatibility. http://www.motorolasolutions.
Special Channel Assignments Emergency Channel If you are in imminent and grave danger at sea and require emergency assistance, use VHF Channel 16 to send a distress call to nearby vessels and the United States Coast Guard. Transmit the following information, in this order: 1 “MAYDAY, MAYDAY, MAYDAY.” 2 “THIS IS _____________________, CALL SIGN __________.” State the name of the vessel in distress 3 times, followed by the call sign or other identification of the vessel, stated 3 times.
• Maritime Radio Use in the VHF Frequency Range • on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.800 MHz frequency. on ships subject to the Safety Convention, the radio must be capable of operating: • • 1 156.050 160.650 2 156.100 160.700 * 156.150 160.750 4 156.200 160.800 5 156.250 160.850 6 156.300 – 7 156.350 160.950 Note: 8 156.
156.900 161.500 66 156.325 160.925 19 156.950 161.550 67** 156.375 156.375 20 157.000 161.600 68 156.425 156.425 * 157.050 161.650 69 156.475 156.475 22 157.100 161.700 71 156.575 156.575 * 157.150 161.750 72 156.625 – 24 157.200 161.800 73 156.675 156.675 25 157.250 161.850 74 156.725 156.725 26 157.300 161.900 75 *** *** 27 157.350 161.950 76 *** *** 28 157.400 162.000 77** 156.875 – 60 156.025 160.625 78 156.925 161.525 * 156.
Maritime Radio Use in the VHF Frequency Range 84 157.225 161.825 85 157.275 161.875 86 157.325 161.925 87 157.375 161.975 88 157.425 162.025 Note: * Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters. ** Low power (1 W) only. *** Guard band. Note: A – in the Receive column indicates that the channel is transmit only.
This glossary is a list of specialized terms used in this manual. ACK Acknowledgment of communication. Active Channel A channel that has traffic on it. Analog Signal An RF signal that has a continuous nature rather than a pulsed or discrete nature. ARS Automatic Registration Service ASTRO 25 Motorola standard for wireless digital trunked communications. ASTRO Conventional Motorola standard for wireless digital conventional communications.
operations of the trunked repeaters. Channel Control Channel Glossary Conventional 194 English A group of characteristics such as transmit/ receive frequency pairs, radio parameters, and encryption encoding. In a trunking system, one of the channels that is used to provide a continuous, two-way/ data communications path between the central controller and all radios on the system. Typically refers to radio-to-radio communications, sometimes through a repeater (see Trunking).
Electrical Serial Number Li-Ion Lithium ion. Failsoft A feature that allows communications to take place even though the central controller has failed. Each trunked repeater in the system transmits a data word informing every radio that the system has gone into failsoft. Man Down FCC Federal Communications Commission.
Glossary static. If the channel is in use, you hear conversation. It also serves as a way to check the volume level of the radio, since the radio “opens the squelch” when the monitor button is pressed. 196 English Multi-System Talkgroup Scan List A scan list that can include both talkgroups (trunked) and channels (conventional). Network Access Code Network Access Code (NAC) operates on digital channels to reduce voice channel interference between adjacent systems and sites.
Refers to a radio control that can have a radio feature assigned to it. PTT Push-To-Talk. The PTT button engages the transmitter and puts the radio in transmit (send) operation when pressed. Radio Frequency (RF) Repeater Selective Call The part of the general frequency spectrum between the audio and infrared light regions (about 10 kHz to 10,000,000 MHz).
Talkaround Bypass a repeater and talk directly to another unit for easy local unit-to-unit communications. Talkgroup An organization or group of radio users who communicate with each other using the same communication path. TMS Text Messaging Service Trunking The automatic sharing of communications paths between a large number of users (see Conventional). Glossary Trunking Priority A scan list that includes Monitor Scan List talkgroups that are all from the same trunking system.
MOTOROLA COMMUNICATION PRODUCTS I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG: MOTOROLA SOLUTIONS, INC.
ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty. MOTOROLA offers the following optional extended service contracts. Limited Warranty SERVICE FROM THE START (SfS) COMPREHENSIVE 200 Provides for extended hardware repair coverage INCLUDING CHEMICAL, LIQUID, FIRE, AND OTHER PHYSICAL DAMAGE.
III. STATE LAW RIGHTS: SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights which may vary from state to state. IV.
adversely affect performance of the Product or interfere with MOTOROLA's normal warranty inspection and testing of the Product to verify any warranty claim. 6 Product which has had the serial number removed or made illegible. 7 Rechargeable batteries if: • Limited Warranty 8 9 10 202 11 English any of the seals on the battery enclosure of cells are broken or show evidence of tampering.
MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product.
Limited Warranty have under the Australian Consumer Law. If you have any queries, please call Motorola Solutions Australia at 1800 457 439. You may also visit our website: http://www.motorolasolutions.com/XA-EN/Pages/ Contact_Us for the most updated warranty terms.
SRX2200_M3.5_BackCover_HalfLetter_P299C.
SRX2200_M3.5_BackCover_HalfLetter_P299C.fm Page 2 Monday, November 3, 2014 5:36 PM Motorola Solutions, Inc. 1303 East Algonquin Road Schaumburg, Illinois 60196 U.S.A. MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2011 and 2015 Motorola Solutions, Inc. All rights reserved.
