VB400 BODY-WORN CAMERA QUICKSTART GUIDE QUICKSTART GUIDE | VB400 1
TABLE OF CONTENTS INTRODUCTION HOW TO CHARGE YOUR VB400 CHARGING WITH A 1-PORT DOCK CHARGING WITH A 14-PORT DOCK BATTERY STATUS LED CONFIGURING YOUR VB400 IDENTIFYING AN RFID ASSIGNED VB400 USING YOUR VB400 TO START / STOP RECORDING WEARING YOUR VB400 ACCESSORIES REGULATORY INFORMATION QUICKSTART GUIDE | VB400 3 4 5 6 7 8 9 10 10 12 13 14 2
INTRODUCTION Thank you for choosing the VB400 Body-worn camera. This simple guide will lead you through the set up and use of your VB400.
HOW TO CHARGE YOUR VB400 Upon receiving your VB400, it is recommended that you fully charge the device before usage. When charging using a 1-Port Dock or 14-Port Dock, insert the camera into the slots as shown below, ensuring the camera clicks securely in place. Check that the top LED blinks green to indicate charging.
CHARGING WITH A 1-PORT DOCK (VB-400-DOCK-SOLO) Connected to your laptop or DockController. If you are charging your VB400 camera via a 1-Port Dock (VB-400-DOCK-SOLO) your camera will bleep to indicate charging has commenced, and the LED, as indicated, will flash green to show charging. Charging: Flashing green LED Fully Charged: Solid green LED Once fully charged, the same LED will turn solid green. If the LED is not lit, the device is not charging.
CHARGING WITH A 14-PORT DOCK (VB-400-DOCK-14/US) Connected to a power supply and DockController If you are charging your VB400 camera via a 14-Port Dock (VB-400-DOCK-14/US) the top LED will flash green to show charging, and the camera will bleep when successfully connected to VideoManager. Charging: Flashing green LED Fully Charged: Solid green LED Once fully charged, the same LED will turn solid green. If the LED is not lit, the device is not charging.
BATTERY STATUS LED To quickly understand the current battery status of your VB400, press the bottom button on the front face of the camera and refer to the bottom LED.
CONFIGURING YOUR VB400 Prior to using your VB400, your device must be configured and assigned to you using VideoManager. For detailed information on how to configure your device, please refer to the VideoManager User Guide. Configured, charged & assigned Solid green light Each VB400 requires a valid VideoManager Licence, in order for you to assign devices and access footage. For further details, see the VideoManager User Guide.
IDENTIFYING AN RFID ASSIGNED VB400 Once your device is configured, your system administrator may wish camera users to utilize an RFID system for camera assignment. For further information on assigning VB400s using an RFID reader, please refer to the VideoManager User Guide. Having presented your RFID card, your docked, assigned VB400 will identify itself with a solid red LED as shown.
USING YOUR VB400 The VB400 series of cameras are intuitive and simple to use. TO START / STOP RECORDING (CONFIGURABLE) Users can activate recording by pressing on the single front button located in the center of the camera as shown. Recording is stopped by pressing and holding the front button. Record activation and deactivation buttons are configurable by Administrators. Start Recording initiated will be indicated by a short bleep, the two upper LEDs showing red.
Stop Recording initiated is indicated by the two upper LEDs turning from red to off, accompanied by a longer, high pitched bleep. PLEASE NOTE: All buttons are configurable. Please consult with your administrator if you have any issues.
WEARING YOUR VB400 The VB400 body-worn camera should always remain upright when capturing footage.
ACCESSORIES Designed for optimum performance and comfort in a wide range of situations, the VB400 comes with a variety of fixing types to suit every uniform and body shape. For more information on our range of body-worn cameras, please visit: www.motorolasolutions.
REGULATORY INFORMATION FCC Responsible party Name: Motorola Solutions, Inc. Address: 2000 Progress Pkway, Schaumburg, Il. 60196 Phone Number: 1-800-927-2744 Hereby declares that the product: Model Name: VB400 Conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d), and section 15.109(a) This device complies with part 15 of the FCC Rules.
INDUSTRY CANADA STATEMENT This device complies with RSS247 of Industry Canada. Cet appareil se conforme à RSS247 de Canada d’Industrie. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. appareils radio exempts de licence.
For more information, please visit: www.motorolasolutions.com/BWC Motorola Solutions, Inc. 500 West Monroe Street, Chicago, IL 60661, U.S.A. 800-367-2346 Availability is subject to individual country law and regulations. All specifications shown are typical unless otherwise stated and are subject to change without notice. MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license.
