Supplement to the Canopy® System Release 8 User Guide PMP 400/430 Series Networks PTP 200 Series Bridges Issue 4 DRAFT 6 November 2009
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Notices See important safety notice on exposure distance in Section 6.3 on page 60. See important regulatory and legal notices in Section 6 on page 55. Trademarks, Product Names, and Service Names MOTOROLA, the stylized M Logo, Canopy, and all other trademarks indicated as such herein are registered trademarks of Motorola, Inc. ® Reg. US Pat & Tm. Office. All other product or service names are the property of their respective owners.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Table of Contents 1 2 Introduction ................................................................................................................. 7 1.1 Document Change History .................................................................................. 8 1.2 Abbreviations ...................................................................................................... 9 1.3 Feedback on Documentation ..........................
PMP 400/430 and PTP 200 Series Supplement 5 6 Canopy User Guide 4.2 Transmitter Output Power (and no Jitter) .......................................................... 34 4.3 Downlink Data %, Range, and Control Slots..................................................... 35 4.4 DFS and Regulatory Parameters for 5.8 & 5.4 GHz Radios ............................. 37 4.4.1 Background and Operation ............................................................................... 38 4.4.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide List of Tables Table 1: Motorola PMP 400/430 and PTP 200 Series .................................................... 11 Table 2: 5.8GHz OFDM - PMP 430 Series Model Number Descriptions ........................ 12 Table 3: 5.4GHz OFDM - PMP 400 and PTP 200 Model Number Descriptions ............. 13 Table 4: 4.9GHz OFDM - PMP 400 and PTP 200 Model Number Descriptions ............. 14 Table 5: CMM4 56VDC and 30 VDC Operation..........................
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Figure 15: 600SS pole mount kit ..................................................................................... 21 Figure 16: PMP 430 SM .................................................................................................. 23 Figure 17: PMP 430 SM with Optional LENS.................................................................. 23 Figure 18: PMP 400 and PTP 200 radio with integrated antenna ..................................
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide 1 Introduction This guide provides product description, planning, configuration, and installation information specific to the PMP 400/430 Series networks and PTP 200 Series bridges in 5.8-GHz, 5.4-GHz and 4.9-GHz bands. PMP 430 – 5.8 GHz PMP 400 – 5.4 GHz PMP 400 – 4.9 GHz Figure 1: PMP 430 CAP 58430 - 5.8 GHz Figure 2: PMP 400 CAP 54400 - 5.4 GHz Figure 3: PMP 400 CAP 49400 - 4.9 GHz Figure 4: PMP 430 CSM 58430 – 5.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide This guide should be used along with the Canopy System Release 8 User Guide, which covers general information, including all network features, RF control features, and GUI (Graphical User Interface) features common across PMP 100, 400, and 500 Series networks and PTP 100 and 200 Series bridges. The Canopy System Release 8 User Guide is available from the “User Guides” section of the Canopy Document Library, http://motorola.motowi4solutions.
PMP 400/430 and PTP 200 Series Supplement 1.
PMP 400/430 and PTP 200 Series Supplement 1.3 Canopy User Guide FEEDBACK ON DOCUMENTATION Is this document accurate, complete, and clear? How can it be improved? Please send your feedback on Canopy documentation to technical-documentation@canopywireless.com. 1.4 TECHNICAL SUPPORT Tip! Do not clear the Event Log after you encounter issues. It may be useful to Technical Support, if you need to escalate the issue. Here is the escalation path for resolution of a problem: 1.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide 2 Product Description PMP 400/430 Series networks and PTP 200 Series bridges add OFDM-based (Orthogonal Frequency Division Multiplexing) products to the Canopy family. • PMP 430 SMs as shown in Figure 4 on page 7 use the Canopy SM form factor with an integrated antenna.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Table 2 shows the Motorola PMP 430 Series (5.8 GHz OFDM) models available. Table 2: 5.8GHz OFDM - PMP 430 Series Model Number Descriptions CSM 58430 Model Number 5.8GHz OFDM Subscriber Module (SM) Description DES or AES 5790SM4 5.8 GHz OFDM SM – 4 Mbps DES 2.6.2 5791SM4 5.8 GHz OFDM SM – 4 Mbps AES 2.6.2 5790SM10 5.8 GHz OFDM SM – 10 Mbps DES 2.6.2 5791SM10 5.8 GHz OFDM SM – 10 Mbps AES 2.6.2 5790SM20 5.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Table 3 shows the Motorola PMP 400 and PTP 200 Series (5.4 GHz OFDM) models available. Table 3: 5.4GHz OFDM - PMP 400 and PTP 200 Model Number Descriptions CSM 54400 Model Number 5.4 GHz OFDM Subscriber Module (SM) Description DES or AES 5440SM 5.4 GHz OFDM SM DES 2.6.4 5441SM 5.4 GHz OFDM SM AES 2.6.4 5440SMC 5.4 GHz OFDM Connectorized SM DES 2.6.5 5441SMC 5.4 GHz OFDM Connectorized SM AES CAP 54400 Model Number 5.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Table 4 shows the Motorola PMP 400 and PTP 200 Series (4.9 GHz OFDM) models available. Table 4: 4.9GHz OFDM - PMP 400 and PTP 200 Model Number Descriptions CSM 49400 Model Number 4.9 GHz OFDM Subscriber Module (SM) Description DES or AES 4940SM 4.9 GHz OFDM SM DES 2.6.4 4941SM 4.9 GHz OFDM SM AES 2.6.4 4940SMC 4.9 GHz OFDM Connectorized SM DES 2.6.5 4941SMC 4.9 GHz OFDM Connectorized SM AES CAP 49400 Model Number 4.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide A Cluster Management Module (CMM4) provides GPS synchronization and power to the PMP 400/430 and PTP 200 series of products: Table 5 details the power requirements of the APs and BHs. Table 5: CMM4 56VDC and 30 VDC Operation Frequency PMP 400/430 Access Point (AP) PTP 200 Backhaul (BH) Canopy Custom Power over Ethernet (PoE) PMP 430 Series – CAP 58430 N/A 56 VDC - Power on pins 5 & 8, return on pins 4 & 7 5.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide A Cluster Management Module (CMMmicro) provides GPS synchronization and 30 VDC power to the: • 5.4-GHz PMP 400 Series - CAP 54400 uses 30 VDC • 5.4-GHz PTP 200 Series - PTP 54200 uses 30 VDC A 600SSC or 600SSD surge suppressor provides over-voltage and over-current protection to APs, SMs, and BHs in various configurations. The diagram in Figure 12 illustrates the use of the 600SS surge suppressor with the PMP 400/430 AP and SM.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Table 6 lists various ancillary equipment and model numbers.
PMP 400/430 and PTP 200 Series Supplement Name Canopy User Guide Model or Part Number Typically use with C C C C P A S A S T P M P M P C C P A S T P M P 5 8 4 3 0 4 9 4 0 0 4.9 GHz SM 56 VDC power supply AC cords (also for isolated 5.8 and 4.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide • nLOS: the installer can see the AP from the SM, but a portion of the first Fresnel zone is blocked. • NLOS: the installer cannot see the AP from the SM and a portion or even much of the first Fresnel zone is blocked, but subsequent Fresnel zones are open. Figure 13 shows examples of LOS, nLOS, and NLOS links.
PMP 400/430 and PTP 200 Series Supplement 2.3 Canopy User Guide CONFIGURATION OPTIONS – RF, IP, DFS These systems use the Canopy Media Access Controller (MAC) layer. Settings like Downlink Data %, Range, and Control Slots are similar to Canopy FSK radios. An AP can communicate to over 200 SMs, similar to a Canopy FSK AP. The GUI (Graphical User Interface) is almost identical to Canopy’s, with a few additions to support OFDM-specific features.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Figure 14: AP Grounding Lug A pole mount kit (model no. SGHN5169A) is available for the 600SS. The pole mount kit provides a grounding point on one of its U-bolts that can be used for terminating ground straps from both the 600SS and the AP.
PMP 400/430 and PTP 200 Series Supplement 2.5 Canopy User Guide ADMINISTRATION SYSTEMS Standard Canopy administration systems are used to support the PMP 400/430 and PTP 200 Series products. The administration systems must be at the appropriate release level. The Prizm element management system is used to manage and monitor Canopy modules and to update module software. Prizm 3.2 with Patch 3 manages and monitors PMP 400/430 and PTP 200 Series modules. Prizm 3.
PMP 400/430 and PTP 200 Series Supplement 2.6.2 Canopy User Guide Specifications for PMP 430 SM radio with integrated antenna • Radio with an integrated, internal antenna • 10 dBi patch antenna - 55° x 55° and 3 dB beam width • Optional LENS adds 6 dBi • Optional reflector dish adds 15 dBi • 1 lb, 11.75 x 3.4 x 3.4 in (hwd) • .45 kg, 29.9 x 8.6 x 8.6 cm (hwd) Figure 16: PMP 430 SM 2.6.
PMP 400/430 and PTP 200 Series Supplement 2.6.4 Canopy User Guide Specifications for PMP 400 and PTP 200 radio with integrated antenna • Radio with an integrated, internal antenna • 15.5° elevation x 17.5° azimuth -- 3 dB beam • 17 dBi gain for antenna at 5.4 GHz. 17 dBi antenna gain plus 10 dBm transmit power gives the regulatory maximum of 27 dBm EIRP. • 17 dBi gain for antenna at 4.9 GHz. 17 dBi antenna gain plus 18 dBm transmit power gives 35 dBm EIRP. • 2.8 lb, 13.25 x 8.25 x 4.
PMP 400/430 and PTP 200 Series Supplement 2.6.6 Canopy User Guide Specifications for PMP 400/430 kitted, connectorized radio (antenna included) • Connectorized radio (N-type connector) and connectorized antenna kitted together • 90° sectors • Antenna optimized for system coverage vs. system self-interference for 90° sectors (3 dB beam pattern of 60° azimuth by 5° elevation, with near-in null fill) • 5.8 GHz - 18 dBi gain for antenna.
PMP 400/430 and PTP 200 Series Supplement 2.7 Canopy User Guide PERFORMANCE Table 7 shows performance details for PMP 400/430 and PTP 200 series. Table 7: Performance Details Product Channel Width Performance Details Parameter 1X Modulation PMP 58430 (5.8 GHz OFDM) 10 MHz QPSK 2 mi/3.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide 3 Planning PMP 400/430 and PTP 200 Series systems use a 10 MHz channel size configurable on 5 MHz centers. This channel size, along with some different characteristics due to the use OFDM carrier technology and QPSK, 16 QAM, or 64 QAM modulations, supports somewhat different channel planning than for standard Canopy.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Available 5.4 GHz channel center frequencies for each region are shown in Table 9. These vary by region due to • different band edge RF specifications (for example, between Canada/US and Europe) • requirements in US, Canada, Europe and Australia to not impinge on the frequencies between 5600 and 5650 MHz, which are frequencies on which some weather radar operate Table 9: 5.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide and, for new equipment, Europe. When the Canopy module is set to either of those regions (configured on the Configuration => General page of the module), it will not allow configuration of the appropriate frequencies, as shown in Table 9. Even in regions where use of the spectrum between 5600 and 5650 MHz is allowed, the best practice is to not use these channels if there are any other usable channels available.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide The built-in spectrum analyzer can be very useful as a tool for troubleshooting and RF planning, but doesn’t duplicate the accuracy and programmability of a dedicated, high-end spectrum analyzer, which may be needed in some cases. 3.6 COLLOCATION OF 5.8 GHZ OFDM WITH STANDARD 5.7 GHZ CANOPY FSK When locating 5.8 GHz PMP 430 OFDM APs near 5.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide 3.7 COLLOCATION OF 5.4 GHZ OFDM WITH STANDARD 5.4 GHZ CANOPY FSK When locating 5.4 GHz PMP 400 and PTP 200 Series OFDM APs near 5.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Procedure 1: Finding collocation values using Frame Calculators 1. Using the “Tools => Frame Calculator” on an OFDM module, enter the desired Downlink Data %, Range, and Control Slot settings, click Calculate, and observe the “Rec SEQ Start” value. 2. Using the “Tools => Frame Calculator” on an FSK module, enter the desired Downlink Data %, Range, and Control Slot settings, click Calculate, and observe the “Rec SEQ Start” value. 3.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide 4 Configuring Most PMP 400/430 Series and PTP 200 Series configuration items are identical or very similar to configuration items in standard FSK Canopy modules. This section discusses those that are new or changed and also remarks on some that remain unchanged. 4.1 LINK OPERATION – 1X/2X/3X PMP 400/430 and PTP 200 Series products offer three levels or speeds of operation – 1X, 2X, and 3X.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Optimal sector utilization involves having as many links as possible running at 3X. This provides as much capacity as possible for the sector. As an example, you want to limit throughput to an individual subscriber to 1X rates. This does not mean you should set that link to 1X operation. Use MIR (Maximum Information Rate) settings to cap the SM’s bandwidth use, but let the link run at as high an operation rate as the RF environment will allow.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Each SM’s Transmitter Output Power is automatically set by the AP. The AP monitors the received power from each SM, and adjusts each SM’s Transmitter Output Power so that the received power at the AP from that SM is not greater than -60 dBm. In addition, for 5.4-GHz SMs, the AP sets the SM’s Transmitter output power so the SM’s EIRP will be within regulatory requirements.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Range does not change transmit power levels. Do not set a higher Range than needed. A higher Range gives no higher power and slightly reduces throughput to allow for higher air delay and turn-around time. If the Range is set to greater than 5 miles, the SM limits the Downlink Data to a maximum of 85% to avoid close-in SMs having registration issues. For example, a Range of 6 miles and a Downlink Data of 90% is not allowed.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide In some cases operators may find that sectors with high levels of small packet requests, such as might be seen in a sector handling several VoIP streams, benefit overall from slightly higher Control Slot settings. If different sectors require different numbers of Control Slots, the operator should use the Frame Calculator to find a combination of settings that put “Rec SEQ Start” times within 300 bit times. See section 3.7.
PMP 400/430 and PTP 200 Series Supplement 4.4.1 Canopy User Guide Background and Operation The modules use region-specific DFS based on the “Region Code” selected on the module’s “Configuration => General” page. By directing installers and technicians to set the Region Code correctly, the operator gains confidence the module is operating according to national or regional regulations without having to deal with the details for each region.
PMP 400/430 and PTP 200 Series Supplement Region Code1 2. 3. 4. 5. Frequency Canopy User Guide AP SM Center Channel Frequencies Available2 (MHz) consistent with your country’s regulatory requirements. In some countries and regions, 5600 MHz to 5650 MHz is “notched” out to meet requirements to not transmit in weather radar frequencies. FCC/IC indicates compliance with FCC Report and Order 03-287 and Industry Canada requirements. ETSI DFS indicates compliance with ETSI EN 301 893 v1.3.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide For all modules running DFS, the module displays its DFS state on its Home => General Status page as one of the following: 4.4.2 • Checking Channel Availability Remaining time n seconds, where n counts down from 60 to 1. • Normal Transmit • Radar Detected Stop Transmitting for n minutes, where n counts down from 30 to 1. • Idle, only for SM/BHS, indicates module is scanning, but has not detected a beacon from an AP/BHM.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Figure 26: Region Code on AP “Configuration => General” page An SM/BHS has both a configurable Region Code and, once it registers to an AP or BHM, an active Regional Code. After an SM/BHS registers to an AP/BHM, it uses the region code of the AP/BHM to determine its DFS behavior and displays the AP/BHM’s region code on its Home => General Status page, as shown in Figure 28.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Figure 27: Configured Region Code on SM Configuration => General page Figure 28: Active Region Code on SM Home => General Status page The AP or BHM always operates under its manually configured Region Code (the one on the Configuration => General page), and so does not show a Region Code on its Home => General Status page.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide It takes two reboots to set the parameters described below on a module starting from factory defaults. Set the Region Code as described above, Save Changes, and Reboot. If the module then invokes DFS (based on the region code and frequency band as shown in Table 12), the Radio Frequency Carriers and External Antenna Gain parameters will be displayed. Set them as described below, Save Changes, and Reboot again.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide • The range is 0 to 35 dB. • A 5.4-GHz SM or BH with an integrated antenna has a Net Antenna Gain of 17 dB. • The antenna sold with the connectorized 5.4 GHz AP has a gain of 18 dB and cable loss of approximately 1 dB, giving a Net Antenna Gain of 17 dB. • A 4.9 GHz SM or BH with an integrated antenna has a Net Antenna Gain of 17 dB. • The antenna sold with the connectorized 4.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide 4.8 CYCLIC PREFIX (CONFIGURABLE ONLY ON PTP 200 BH & PMP 430 AP/SM) OFDM technology uses a cyclic prefix, where a portion of the end of a symbol (slot) is repeated at the beginning of the symbol (slot) to allow multi-pathing to settle before receiving the desired data.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide 5 Installation WARNING! Installing a unit usually involves height, electricity, and exposure to RF (Radio Frequency) energy. To avoid personal injury, follow applicable national and local safety regulations along with industry best practices. Also follow the specific guidelines in this document, including Exposure Separation Distances in section 6.3 on page 60. 5.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Procedure 2: Assembling a 5.8 or 5.4 GHz AP, and attaching to tower 1. Perform a parts check to ensure all parts are present. 2. Assemble the upper bracket, per the diagram that comes with the antenna. 3. Connect the radio to the antenna by sliding it into the captive space. Secure the radio to the antenna using the two bolts provided. 4. Assemble the lower bracket on the antenna assembly.
PMP 400/430 and PTP 200 Series Supplement 6. Use standard work and safety practices for tower climbing. Connect the upper bracket to a pole, mounting fixture, or the tower. 7. Hang the antenna assembly on the upper bracket. Canopy User Guide 8. Connect the lower bracket to the pole or tower using the quick-connect system provided 9. The quick-connect system allows easy attachment, detachment, and adjustment without any lose parts.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide 10. Adjust down tilt per calculations done during Planning. Confirm down tilt after the radio is operational using SMs in the field at selected test locations. Procedure 3: Assembling a 4.9 GHz AP, and attaching to tower 1. Perform a parts check to ensure all parts are present. 2. Assemble unit per the instructions that come with the kit.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide 3. Connect the radio to the antenna by sliding it into the captive space. Secure the radio to the antenna using the two bolts provided. 4. Connect coax N-connector 5. Use standard work and safety practices for tower climbing, and connect the upper assembly to a pole, mounting fixture, or the tower.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide 6. Adjust down tilt per previous calculations done during Planning. Confirm down tilt after the radio is operational using SMs in the field at selected test locations.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Procedure 4: Cabling and Grounding/Earthing the AP 1. Standard Canopy installation practices apply, including using shielded Ethernet cable for all infrastructure cabling, using drip loops, providing extra cable for future use at any termination, and ensuring the tower or structure is fully grounded (Protective Earth – PE). 2. Use dielectric grease (which is uniformly non-conducting) on all connections and in all RJ-45 Ethernet connectors.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Install a 600SS surge suppressor within 3 ft (~1 m) of an AP or BH. A pole mount kit for the 600SS is shown in Figure 15 to facilitate installation of the 600SS by the AP or BH. Up to four 600SS surge suppressors may be mounted in series on an Ethernet link without degrading the link. The equivalent of a 600SS is built into each of the 8 ports on a CMM4 and counts as one of the four.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Figure 31: Dielectric Grease - Insert Ethernet Cable The PMP 400 SM and PTP 200 BH have a ground/Protective Earth lug, just like the AP. Although not as critical as in the case of the AP (where there is metal-to-metal connectivity through the coax and antenna to ground), the lug can be used to ground the SM or BH for additional protection. In addition, a 600SS can be used within 3 ft (1 m) of the SM or BH to provide additional protection.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide 6 Regulatory and Legal Notices 6.1 IMPORTANT NOTE ON MODIFICATIONS Intentional or unintentional changes or modifications to the equipment must not be made unless under the express consent of the party responsible for compliance. Any such modifications could void the user’s authority to operate the equipment and will void the manufacturer’s warranty. 6.2 6.2.1 NATIONAL AND REGIONAL REGULATORY NOTICES U.S.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Table 13: US FCC IDs and Industry Canada Certification Numbers and Covered Configurations FCC ID ABZ89FT7634 ABZ89FT7635 --- --- ABZ89FT7629 --- ABZ89FT7631 Industry Canada Cert Number --- --- 109W-5780 109W-5790 --- 109W-5440 109W-4940 Frequencies Module Families Antenna 10 MHz channels, centered on 57305845 in 5 MHz increments (within the 5725-5850 MHz ISM band) 5780APC 16 dBi connectorized PCTEL Model 8514724E01 antenna (60
PMP 400/430 and PTP 200 Series Supplement 6.2.2 Canopy User Guide Industry Canada (IC) Notification For 5.4-GHz devices: This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Motorola Canopy Radio equipment operating in the 5470 to 5725 MHz band are categorized as “Class 1” devices within the EU in accordance with ECC DEC(04)08 and are “CE” marked to show compliance with the European Radio & Telecommunications Terminal Equipment (R&TTE) directive 1999/5/EC. The relevant Declaration of Conformity can be found at http://motorola.motowi4solutions.com/doc.php.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide For compliant operation in the 5.4 GHz band, the Equivalent Isotropic Radiated Power from the integrated antenna or connectorized anteanna shall not exceed 27 dBm (0.5 W). The operator is responsible for enabling the DFS feature on any Canopy 5.4 GHz radio by setting the Region Code to “Brazil”, including after the module is reset to factory defaults.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Table 14: Disclosure Table 部件名称 金属部件 电路模块 电缆及电缆组件 塑料和聚合物部件 有毒有害物质或元素 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 6+ (Cr ) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) × ○ × × ○ ○ × ○ × × ○ ○ × ○ × × ○ ○ ○ ○ ○ ○ ○ × ○: 表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006 标准规定的限量要求以下。 ×: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006 标准规定的限量要求。 6.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Guidelines for Limiting Exposure to Time-Varying Electric, Magnetic, and Electromagnetic Fields. The applicable power density exposure limits from the documents referenced above are • 10 W/m2 for RF energy in the 5.4-GHz frequency bands.
PMP 400/430 and PTP 200 Series Supplement • Canopy User Guide The calculated compliance distance d is overestimated because the far-field equation models the antenna as a point source and neglects the physical dimension of the antenna. 6.4 LEGAL NOTICES 6.4.1 Software License Terms and Conditions ONLY OPEN THE PACKAGE, OR USE THE SOFTWARE AND RELATED PRODUCT IF YOU ACCEPT THE TERMS OF THIS LICENSE.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide disk(s), provision of downloadable patch or replacement code, or refund of the unused portion of your bargained for contractual benefit up to the amount paid for this Software License.
PMP 400/430 and PTP 200 Series Supplement Canopy User Guide Right to Audit. Motorola shall have the right to audit annually, upon reasonable advance notice and during normal business hours, your records and accounts to determine compliance with the terms of this Agreement. Export Controls. You specifically acknowledge that the software may be subject to United States and other country export control laws.