User Manual
Table Of Contents
- Contents
- List of Figures
- List of Tables
- Copyrights
- General Information
- Getting Started
- Product Technical Information
- Controls and Indicators
- Display
- Status Icons
- Powering On the Radio
- Unlocking Your Radio
- Locking/Unlocking the Keys/Buttons
- External SIM Card Priority
- Entering TMO / DMO Mode
- Transmit Inhibit Mode
- Selecting Talkgroups
- Talkgroup Icon Selection
- Using Timed Talkgroup Change
- Activating Talkgroup Scanning
- Broadcast Call
- Ambience Listening (AL) Call
- One-Touch Button Feature
- Terminal Temporary Disable/Enable
- Terminal Permanent Disable
- During the Call
- Writing Text
- Home Display Text Message
- Modes
- Using Networks
- Trunked Mode Operation
- Entering TMO Mode
- Selecting Talkgroups
- Making Group Calls in TMO
- Receiving Group Calls in Idle
- Receiving Group Calls during Ongoing Group Calls
- Dynamic Group Number Assignment (DGNA)
- DGNA Reception
- DGNA Auto Select Group
- DGNA Auto Reselect Group
- Viewing DGNA Talkgroups
- Broadcast Calls Initiated by Users
- Initializing Broadcast Calls
- Phone and PABX Calls
- Private Call
- Making Private Calls
- Assistance Call
- Call Modification
- Local Site Trunking
- Direct Mode Operation
- Entering DMO Mode
- Selecting Talkgroups
- Making Group Calls in DMO
- Receiving Group Calls in Idle
- Private Call
- Making Private Calls
- Private Call With Presence Check
- DMO Private Priority Call
- Talkgroup for Individual Calls
- Communication through Repeaters
- Communication through Gateways
- Selecting DMO Group Call Options
- Transmit Inhibit Mode
- Emergency Operations
- Emergency Group Call
- Making Emergency Group Calls
- Receiving Emergency Group Calls
- Non-Tactical Emergency
- Emergency Individual Calls (Private or MS-ISDN)
- Emergency Alarm
- Emergency SDS Status
- Emergency Hot Microphone
- Alternating Hot Microphone
- Silent Emergency Mode
- Invisible Emergency
- Emergency Mode by Dialing
- Disaster Alert
- Initializing Disaster Alert Calls
- Exiting Emergency Operations
- Repeater Mode
- Gateway Mode
- GPS Location Service
- Main Menu
- Scrolling through the Menu
- Menu Icons
- Messages
- Contacts
- Browser
- Security
- Setup
- Group Setup
- Favorites
- My Info
- Recent Calls
- Shortcuts
- RUI
- Networks
- Location
- Packet Data
- Features
- Private Call
- Radio Messaging System (RMS)
- One-Touch Dial
- Talkgroup Dialing by Index
- Phone and PABX Calls
- Phone/PABX Speed Dial
- DTMF Overdial
- Short Number Dial
- Dual Control Head
- RUA/RUI
- WAP
- Call-Out
- Shadow Groups (Address Bundle)
- Appendix A: Tones
- Appendix B: LED Indications
- Appendix C: Troubleshooting
- End — cancels the incoming Group Call.
Dynamic Group Number Assignment (DGNA)
DGNA allows the network operator to dynamically manage talkgroups on your radio over the air
interface. Using DGNA, the network operator can:
• Add talkgroups.
• Attach or select newly added talkgroups.
• Delete talkgroups.
• Modify parameters of existing talkgroups.
All the above operations are performed by transmitting data to your radio.
DGNA Reception
When a DGNA message is received, your radio plays a tone and displays a message Talkgroup list
updated. If enabled by your service provider, your radio displays all added and deleted talkgroup list.
When your service provider deletes (de-assigns) the currently selected talkgroup, depending on the
settings, the radio can perform one of the following actions:
• Enter the “No Group” state – the radio does not attach to any talkgroup automatically.
• Attach to the last selected TMO talkgroup. If the last selected TMO talkgroup is not available (it was
deleted), the radio enters the “No Group” state.
• Attach to a default talkgroup configured by your service provider. If the default talkgroup is not
available (it was deleted), the radio enters the “No Group” state.
At each talkgroup change, an appropriate notification is shown on the display.
If the DGNA message is received to delete all talkgroups, your radio displays All Talkgroups Deleted.
To exit the DGNA display, you can use the BackSOFT key or the END key.
DGNA Auto Select Group
If the DGNA Auto Select is configured, whenever your radio receives a DGNA, it switches to the added
talkgroup.
DGNA Auto Reselect Group
If the DGNA Auto Reselect is configured, whenever a talkgroup assigned by the network operator via
DGNA is deassigned without the user action, the radio returns to the previously selected group.
Viewing DGNA Talkgroups
Prerequisites: Your radio receives the DGNA message.
Procedure:
1 To view the added talkgroups details press View.
2 Scroll through the list to select required talkgroup.
3 To select the DGNA group, press Attach.
Chapter 3: Modes
Send Feedback 49