VM2500 - WiMAX Vehicular Subscriber Module (VSM) Installation Guide
WiMAX VSM Installation Guide 6802987C01 Revision A January 2010
ii WiMAX VSM Installation Guide © 2009 by Motorola, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis.
iii Revision History Changes to the original manual are listed below: Change A Date Description Initial release
iv WiMAX VSM Installation Guide
Table of Contents Patents........................................................................................................................... ii Warranty ........................................................................................................................ ii Revision History............................................................................................................. iii About This Guide Introduction ..................................................................
vi WiMAX VSM Installation Guide WiMAX Antennas .................................................................................................... WiFi Antenna .......................................................................................................... GPS Antenna .......................................................................................................... Cables ....................................................................................................................
About This Guide Introduction The WiMAX VSM Installation Guide provides general instructions for installing, setting up, operating, maintaining, and troubleshooting the WiMAX VSM.
viii WiMAX VSM Installation Guide Chapter Descriptions Topics covered in this guide are as follows: • Chapter 1, WiMAX VSM Description provides the product overview. • Chapter 2, Installation provides unpacking instructions and all required procedures for installing the WiMAX VSM. • Chapter 3, Configuring and Monitoring the VSM provides the procedures that enable configuring the WiMAX VSM for best operation.
About This Guide ix Notational Conventions The following conventions are used in this document: • Italics are used to highlight the following: • Chapters and sections in this and related documents • Dialog box, window and screen names • Drop-down list and list box names • Check box and radio button names • Bold text is used to highlight the following: • Key names on a keypad • Button names on a screen.
x WiMAX VSM Installation Guide Safety Before installing/using this product, the installer/operator must be familiar with the RF energy awareness information and operating instructions in the “Product Safety and RF Energy Exposure Booklet” enclosed with the WiMAX VSM (Motorola Publication part number 68P81095C99) to ensure compliance with Radio Frequency (RF) energy exposure limits. FCC Interference This device complies with Part 15 of the FCC Rules.
Chapter 1 WiMAX VSM Description The WiMAX VSM Unit The Motorola WiMAX Vehicular Subscriber Module (VSM) is a high/medium power infrastructure modem. Two models are available: • F7300A without WiFi, 1.12W (29.5+1 dBm) for US and Canada, and 0.5W (26+/-1dBm) for EU • F7400A with WiFi, 1.12W (29.5+1 dBm) for US and Canada, and 0.5W (26+/-1dBm) for EU (WiMAX), and 160mW (21+1 dBm) for US and Canada, and 56mW (16.5 +/-1dBm) for EU (WiFi). See Figure 1-1.
1-2 WiMAX VSM Installation Guide 3 1 2 1 Modem 2 LED Indicator Panel (Front Panel) 3 Connectors Panel (Back Panel - not shown) Figure 1-1 WiMAX VSM - General View For detailed specifications of the VSM unit, see Appendix A: Specifications. Modem The modem has a Connectors panel (back panel) and a LED Indicator panel with On/Off button (front panel).
WiMAX VSM Description 1-3 • 1 RF cable SMA type connector (GPS) 1 3 6 5 2 Figure 1-2 Connectors Panel 1 LAN/Ethernet communication connector (RJ45) 2 2 RF TNC type connectors (WiMAX) 3 DC power connector 4 RF reverse SMA type connector (WiFi) 5 Ignition connector 6 RF SMA type connector (GPS) 4 (for F2378A model only)
1-4 WiMAX VSM Installation Guide LED Indicator Panel with On/Off Button A set of five LEDs is used for diagnostics and testing of the unit (see Figure 1-3).
WiMAX VSM Description 1-5 LED Indicators Functions Table 1-1 describes the functions of the LED indicators on the VSM front panel.
1-6 WiMAX VSM Installation Guide
Chapter 2 Installation Unpacking and Inspecting the Shipment Unpack your shipment and check the contents to ensure that you have received all the specified items. Thoroughly inspect the equipment for shipping damage as soon as possible after delivery. Report any damage you find to your Motorola Customer Service representative immediately. Safety and General Information A properly installed VSM unit minimizes service calls.
2-2 WiMAX VSM Installation Guide • Only qualified personnel may install communication equipment. • Ensure secure tightening of cable connectors. NOTE Install this product in a vehicle in accordance with the vehicle manufacturer’s guidelines and the instructions detailed in this manual. Use only the Motorola parts specified in this manual. Check the required mounting locations. It might be necessary to penetrate the bulkhead to reach the battery.
Installation 2-3 Planning the Installation Planning is the key to fast, easy and safe installation. IMPORTANT Take the following points into consideration when selecting a location and planning the installation. Installation Constraints Refer to the Safety Instructions in “Product Safety and RF Energy Exposure Booklet for Mobile Two-Way Radios in Vehicles or as Fixed Site Control” P/N 6881095C99.
2-4 WiMAX VSM Installation Guide Figure 2-2 gives the WiMAX VSM dimensions. 3.66” (9.3 cm) 11.4” (29 cm) 7.9” (20 cm) Figure 2-2 WiMAX VSM - Dimensions Cables Routing • Before running a wire or drilling a hole, inspect the vehicle and determine how and where you intend to mount the antenna, modem, and the input/output device. • Plan wire and cable routing to provide maximum protection from overheating, battery acid, moving parts and sharp edges.
Installation 2-5 • When drilling a hole in the roof, take care not to snag the roof liner. • To prevent rusting after drilling, remove all metal burrs and residue, and completely clean the area to ensure the removal of all steel dust. • Insert rubber grommets in all drilled holes to protect cables.
2-6 WiMAX VSM Installation Guide Antennas WiMAX Antennas Use the following WiMAX antennas (2 identical antennas) with the VSM: • Kit No. FHN7278A The antennas are supplied with a 12 feet coaxial cable and a TNC male connector, not mounted (see Figure 2-3).
Installation WiFi Antenna Use one of the following WiFi antennas with the VSM: • Kit No. FHN7279A • Kit No. FAF5261A The antenna is supplied with a 12 feet coaxial cable and a reversed SMA male connector (see Figure 2-4).
2-8 WiMAX VSM Installation Guide GPS Antenna Use the following GPS antenna with the VSM: • Amphenol P/N SA1904-04-000-R (Kit No. FHN7280A) The antenna is supplied with a 13 feet RG174 cable and a SMA male connector (see Figure 2-5). Figure 2-5 GPS Antenna Cables The following cables are supplied with the WiMAX VSM (see Figure 2-6).
Installation 2-9 Mounting Tray Use the tray for mounting the VSM securely on a flat surface. 2.7” (6.9 cm) 11.1” (28.2 cm) 8.19” (20.8 cm) Figure 2-7 Tray Dimensions Modem Installation Process Process 2-1 describes the steps for the modem installation. Process 2-1 Modem Installation Process 1 Ensure adequate space for the installation. (See Planning the Installation on page 2-3) 2 Install the antennas. (See Antennas Mounting on page 2-10). 3 Route the cables.
2 - 10 WiMAX VSM Installation Guide Process 2-1 Modem Installation Process (Continued) 8 Connect the GPS cable (see GPS Antenna Cable Installation on page 2-13) 9 Connect the LAN/Ethernet cable. (See LAN/Ethernet Cable Installation on page 2-14) 10 Place caps on unused connector(s). (See Cap Installation on page 2-14) Antennas Mounting Process 2-2 gives general instructions for mounting all types of antennas.
Installation 2 - 11 Modem Installation Procedure Process 2-3 describes how to install the modem on a flat surface. Process 2-3 How to Install the Modem on a Flat Surface 1 Position the tray in the desired location. Mark the positions of the six bottom mounting holes (1) using the tray as a template. Be careful not to affect the tray. See Figure 2-8. 1 Figure 2-8 Mounting Tray 2 Centerpunch the marked spots and fix the tray in position using the self-drilling supplied screws.
2 - 12 WiMAX VSM Installation Guide Cables Routing and Connection Procedure DC Power and Ignition Cable Installation NOTE The VSM supports 12 V vehicle batteries, i.e. 13.8 V ±20% DC vehicle batteries. The DC Power cable is equipped with 5-Ampere fuse (slow-blow). Verify that the vehicle electrical system can support current values larger than that. Connect the fuse in the red wire to the power source using the shortest practical length. The unit is only for use with a negative ground system.
Installation 2 - 13 Process 2-4 How to Install the DC Power and Ignition Cable (Continued) 5 Verify that the cables in the engine compartment do not obstruct any of the vehicle controls or touch hot or moveable parts of the engine. 6 For ignition installation, perform the following steps: a. Cut the green lead to the desired length. b. Connect the green lead of the DC Power cable to ignition (+). Cable tie the wire every 4” (10 cm) along its length, do not tie to existing vehicle systems. c.
2 - 14 WiMAX VSM Installation Guide LAN/Ethernet Cable Installation Process 2-8 How to Install the LAN/Ethernet Cable 1 Connect the LAN/Ethernet cable from the LAN connector on the Connectors panel to the input/output device. Verify that the cable P/N label is facing the opposite side of the VSM cooling fins. See Figure 2-11. Do not use pliers or any other metallic tool for tightening.
Chapter 3 Configuring and Monitoring the VSM Introduction The WiMAX VSM is basically a plug and play modem and will, most of the time, access the network without any configuration. Some service providers require special security configuration. This chapter provides required security configuration procedures and other general configuration procedures that may be done by your system administrator after the modem installation completion.
3-2 WiMAX VSM Installation Guide 5. The following login window appears. NOTE 6. The default password is motorola. Click the “Login” button to open the configuration application Wizard.
Configuring and Monitoring the VSM The Configuration Wizard After login, the following wizard window appears.
3-4 WiMAX VSM Installation Guide Configuring the WiMAX VSM Security NOTE If required by your service provider, you will need to configure your WiMAX VSM security settings. 1. In the upper part of the window, click on the “Internet” tab. The following window appears. 2. Verify that the WiMAX Security tab is selected. 3. Using the pull-down menu, select the authentication method. 4. According to the selected authentication method, fill in the required user name and password. 5.
Configuring and Monitoring the VSM Configuring the WiMAX VSM Time Zone 1. In than upper part of the window, click on the “Personalize” tab. The following window appears. 2. Verify that the “Device Time” tab is selected. 3. Using the pull-down menu, select the required Time Zone. 4. If required, check the “Auto Adjust for Daylight Saving Time” checkbox. 5. When finished, click “Apply”. Monitoring the WiMAX VSM Operation NOTE Verify that the Status Utility is installed on your computer.
3-6 WiMAX VSM Installation Guide 2. To access the status utility, double click the signal strength icon. 3. The following “Connection” screen is displayed as a default. 4. Click the upper tabs to receive the required system information you need.
Configuring and Monitoring the VSM 5. To close the status utility, click the X button on the upper right corner of the screen.
3-8 WiMAX VSM Installation Guide
Chapter 4 Troubleshooting Introduction Motorola has made every effort to ensure that this product is of excellent quality. However, if you experience any problems with the product, please contact your local Motorola representative with product related information. For complete information on ordering required parts and kits, contact your local customer service representative and refer to Appendix B, Reference.
4-2 WiMAX VSM Installation Guide Malfunction Probable Cause Corrective Action No WiMAX connection. WiMAX antenna/s are not connected (WiMAX LED is blinking orange). Connect the WiMAX antenna/s. Verify that the WiMAX LED is green. No WiFi connection. WiFi antenna is not connected (WiFi LED is off). Connect the WiFi antenna/s. Verify that the WiFi LED is green. No LAN/Ethernet connection. LAN/Ethernet connector on the VSM is not installed correctly (LAN LED is off).
Appendix A Specifications Physical Dimensions (Modem) 11.4”x7.9”x3.66” (29cm x 20cm x 9.3cm) Weight (Modem) 12.3 Pounds (5.
A-2 WiMAX VSM Installation Guide LEDs LED Name WiFi WiMAX GPS LAN PWR LED Status Solid Green WiFi is Available Connected GPS Data Available Link Established Power On Blinking Green Rx/Tx Activity Connecting/ Registering - - - Solid Orange - - GPS Data is not available (searching for signal) - No ignition On/Off switch is pressed but ignition is Off Blinking Orange - Scanning - Ethernet activity - Solid Red - Failure/ Overheat Failure - Standby External power is connected
Standard Default Parameters WiMAX Antenna Type Collinear dipole array Frequency 2.5 - 2.7 GHz Physical Fiberglass U.V. stable Impedance 50 Ohms (nominal) Polarization Vertical Linear Height 17inches (43cm) Azimuth pattern Omni-directional Elevation beamwidth 15 deg WiFi Antenna Type Collinear dipole array Frequency 2.4 - 2.
A-4 WiMAX VSM Installation Guide RF Characteristics Frequency WiMAX WiFi 2.495 - 2.690 GHz 2.412 - 2.442 GHz Bandwidth WiMAX 5 MHz 10 MHz WiFi 22 MHz Output transmit power WiMAX band (US and Canada) WiMAX band (EU) 29.5 dBm average 26 dBm avarage WiFi band (US and Canada) WiFi band (EU) 21 dBm average 16.5 dBm average Receiver Packet Error Rate (PER) WiMAX -72.
Appendix B Reference Replacement Parts Replace damaged parts with identical replacement parts. For complete information on ordering required parts and kits, contact your local customer service representative.
B-2 WiMAX VSM Installation Guide Kit Replacement Parts List Kit/Part Number Description F7400A WiMAX VSM Modem with WiFi F7300A WiMAX VSM Modem without WiFi
MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their respective owners. © Motorola, Inc.
