O5Head_6875947M01_C.
O5Head_6875947M01_C.
O5Head_6875947M01_C.book Page 3 Wednesday, October 20, 2010 12:13 PM m Radio On/Off ASTRO® APX™ O5 Control Head Mobile Radio Quick Reference Card Product Safety and RF Exposure Compliance ! Caution Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements.
O5Head_6875947M01_C.book Page 4 Wednesday, October 20, 2010 12:13 PM Sending an Emergency Call (Trunking Only) 1 Press Emergency button. 2 A tone sounds and the display alternates EMERGENCY and the home display. OR A talk prohibited tone sounds when the selected channel does not support emergency. 3 Press and hold the PTT button. Speak clearly into the microphone. 4 Release the PTT to end the transmission. To exit emergency at any time, press and hold the Emergency button.
O5Head_6875947M01_C.book Page i Wednesday, October 20, 2010 12:13 PM Declaration of Conformity DECLARATION OF CONFORMITY Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola, Inc. Address: Motorola, Inc. 1301 E. Algonquin Rd.Schaumburg, IL60196-1078, U.S.A. Phone Number: 1-800-927-2744 Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below.
O5Head_6875947M01_C.book Page ii Wednesday, October 20, 2010 12:13 PM Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
O5Head_6875947M01_C.book Page iii Wednesday, October 20, 2010 12:13 PM SecureNet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Contents Preparing Your Radio for Use . . . . . . . . . . . . . .3 Declaration of Conformity . . . . . . . . . . . . . . . . . .i Turning On the Radio . . . . . . . . . . . . . . . . . . . . . . . . 4 Validating Compatibility During Power Up . . . . . . . . 4 Important Safety Information . . . . . . . . . . . . . .ix Adjusting the Volume . . . . . . . . . .
O5Head_6875947M01_C.book Page iv Wednesday, October 20, 2010 12:13 PM Keypad Characters – Uppercase Mode . . . . . . . . . 12 Keypad Characters – Lowercase Mode . . . . . . . . . 13 Keypad Characters – Numeric Mode . . . . . . . . . . . 14 Keypad Characters – Hexadecimal Mode . . . . . . . 15 Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . 16 Identifying Status Indicators . . . . . . . . . . . . . .16 Making a Talkgroup Call . . . . . . . . . . . . . . . . . . . . .
O5Head_6875947M01_C.book Page v Wednesday, October 20, 2010 12:13 PM All Active Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Intercom Feature in All Active Mode . . . . . . . . . . . 41 Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Making a Private Call from Contacts . . . . . . . . . . . .43 Adding a New Contact Entry . . . . . . . . . . . . . . . . . .45 Deleting a Contact Entry . . . . . . . . . . . . . . . . . . . . .
O5Head_6875947M01_C.book Page vi Wednesday, October 20, 2010 12:13 PM Text Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Appending or Removing a Request Reply to a Text Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Appending a Priority Status and a Reply Request to a Text Message . . . . . . . . . . . . . . . . . . . . . . . . . 67 Removing a Priority Status and a Reply Request from a Text Message . . . . . . . . . . . . . . . . . . . . . . .
O5Head_6875947M01_C.book Page vii Wednesday, October 20, 2010 12:13 PM Initiating an Announcement . . . . . . . . . . . . . . . . . . 90 Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Viewing Recent Calls List . . . . . . . . . . . . . . . . . . . .92 Selecting the Power Level . . . . . . . . . . . . . . . . . . . .93 Selecting a Radio Profile . . . . . . . . . . . . . . . . . . . . .93 Controlling the Display Backlight . . . . . . . . . . . . . . .
O5Head_6875947M01_C.book Page viii Wednesday, October 20, 2010 12:13 PM Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 Contents Commercial Warranty and Service . . . . . . . .
O5Head_6875947M01_C.book Page ix Wednesday, October 20, 2010 12:13 PM Important Safety Information ! Caution Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. All the features described in the following sections are supported by the radio's software version R05.00.00 or later. Accessing Radio Information on page 98 to determine your radio's software version.
Computer Software Copyrights O5Head_6875947M01_C.book Page x Wednesday, October 20, 2010 12:13 PM Computer Software Copyrights Documentation Copyrights The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media.
O5Head_6875947M01_C.book Page 1 Wednesday, October 20, 2010 12:13 PM Getting Started How to Use This User Guide Throughout the text in this publication, you will notice the use of WARNING, Caution, and Note. These notations are used to emphasize that safety hazards exist, and the care that must be taken or observed.The following special notations identify certain items: ! WARNING An operational procedure, practice, or condition, etc., which may result in injury or death if not carefully observed.
O5Head_6875947M01_C.book Page 2 Wednesday, October 20, 2010 12:13 PM CrossTalk Prevention Example Description Home button Buttons and keys are shown in bold print or as or H an icon. PHONE Menu entries are shown similar to the way they appear on the radio’s display. > This means “Press the right side of the 4-way Navigation button.
O5Head_6875947M01_C.book Page 3 Wednesday, October 20, 2010 12:13 PM What Your Dealer/System Administrator Can Tell You • Is your radio preprogrammed with any preset conventional channels? • Which buttons have been programmed to access other features? • What optional accessories may suit your needs? Turning On the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . page 4 Validating Compatibility During Power Up. . . . . . . . . . page 4 Adjusting the Volume . . . . . . . . . . . . . . . . . . .
O5Head_6875947M01_C.book Page 4 Wednesday, October 20, 2010 12:13 PM To turn off the radio, press the Power On/Off Button after the LEDs light up. Turning On the Radio Preparing Your Radio for Use Press the Power On/Off Button briefly to power on the radio. After a short time, the red, yellow and green LEDs light up. The display then shows Zone and channel text, and menu items display on the screen.
O5Head_6875947M01_C.book Page 5 Wednesday, October 20, 2010 12:13 PM Adjusting the Volume To decrease the volume, rotate the Volume Knob counterclockwise. Volume Knob Identifying Radio Controls Take a moment to review the following: Radio Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . page 6 O5 Control Head and Microphone . . . . . . . . . . . . . . . page 6 Programmable Features . . . . . . . . . . . . . . . . . . . . . . . . page 7 Assignable Radio Functions . . . . . . . . . . . .
O5Head_6875947M01_C.
O5Head_6875947M01_C.book Page 7 Wednesday, October 20, 2010 12:13 PM Programmable Features Emergency – Depending on the programming, initiates or cancels an emergency alarm or call. Information – Displays the basic radio information, IP-related information, and buttons or switches control mapping.
O5Head_6875947M01_C.book Page 8 Wednesday, October 20, 2010 12:13 PM One Touch 1 – 4 – Launches a specific feature with one single button-press. You can setup as much as four separately programmed buttons for four different features. Phone – Allows you to make and receive calls similar to standard phone calls. Private Call (Trunking Only) – Allows a call from an individual radio to another individual radio.
O5Head_6875947M01_C.book Page 9 Wednesday, October 20, 2010 12:13 PM Assignable Settings or Utility Functions Front/Rear – Switches one of two control heads to be active at one time. You can access various radio functions through one of the following ways: • A short or long press of the relevant programmable buttons. Horns/Lights – Toggles horns and lights feature on or off. Low Power – Toggles transmit power level between high and low.
O5Head_6875947M01_C.book Page 10 Wednesday, October 20, 2010 12:13 PM Using the Advance Programmable Buttons Using the Navigation Buttons This feature is to help you to shorten the process of applying certain common features. Home Button Orange Button* The H button returns you to the home (default) display. In most cases, this is the current mode.
O5Head_6875947M01_C.book Page 11 Wednesday, October 20, 2010 12:13 PM 4-Way Navigation Button Press and release one of the button to scroll from one entry to the next one. Press and hold one of the button to have the radio toggles through the list automatically (release the button to stop). Volume Knob Use this Volume Knob to adjust the volume of the speakers by turning it clockwise or counterclockwise.
O5Head_6875947M01_C.book Page 12 Wednesday, October 20, 2010 12:13 PM Using the Keypad You can use the 3 x 4 alphanumeric keypad on the keypad microphone to access your radio’s features. The keypad functions in a manner similar to a standard telephone keypad when entering numeric digits. When the keypad is used to edit a list, each key can generate different characters of the alphabet. The tables below show the number of times a key needs to be pressed to generate the required character.
O5Head_6875947M01_C.book Page 13 Wednesday, October 20, 2010 12:13 PM Keypad Characters – Lowercase Mode Key 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 1 1 . , ? ! ; @ _ - * # & $ / + = \ “ ‘ ( ) 2 a b c 3 d e f 4 g h i 5 j k l 6 m n o 7 p q r 8 t u v 9 w x y s z Identifying Radio Controls Number of Times Key is Pressed 0 Toggle between mixed case mode, uppercase mode, and lowercase mode.
O5Head_6875947M01_C.book Page 14 Wednesday, October 20, 2010 12:13 PM Keypad Characters – Numeric Mode Identifying Radio Controls Number of Times Key is Pressed Key 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 1 1 . , ? ! ; @ _ - * # & $ / + = \ “ ‘ ( ) 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 0 0 * Space # Toggle between numeric and letter mode.
O5Head_6875947M01_C.
O5Head_6875947M01_C.book Page 16 Wednesday, October 20, 2010 12:13 PM Push-To-Talk (PTT) Button The PTT button on the side of the microphone serves two basic purposes: PTT Button • While a call is in progress, the Identifying Status Indicators PTT button allows the radio to transmit to other radios in the call. Press and hold down PTT button to talk. Release the PTT button to listen. The microphone is activated when the PTT button is pressed.
O5Head_6875947M01_C.book Page 17 Wednesday, October 20, 2010 12:13 PM Status Icons N The following are the icons that appear on the radio’s display. u Receiving Radio is receiving a call or data. t Transmitting Radio is transmitting a call or data. F V Call Received Radio has received an Individual Call. • On = Radio is currently configured for direct radio-to-radio communication (during conventional operation only). • Off = Radio is connected with other radios through a repeater.
O5Head_6875947M01_C.book Page 18 Wednesday, October 20, 2010 12:13 PM j Priority Channel Scan • Blinking dot = Radio detects activity on channel designated as Priority-One. Location Signal G • Blinking = Location feature is enabled, but no Identifying Status Indicators designated as Priority-Two. • On steady = View mode • Blinking = Program mode k location signal is available. User Login Indicator (IP Packet Data) n • Off = Clear operation. • Blinking = Receiving an encrypted voice call.
O5Head_6875947M01_C.book Page 19 Wednesday, October 20, 2010 12:13 PM Text Messaging Service (TMS) Icons 3/6 Status Icons The following icons appear on the radio’s display for TMS features: , Inbox Full The Inbox is full. [ Message Sent The text message is sent successfully. Z Message Unsent The text message cannot be sent. r Unread Message I P Read Message The selected text message in the Inbox has been read. Message Index Indicates the index of the current message the user is viewing.
O5Head_6875947M01_C.book Page 20 Wednesday, October 20, 2010 12:13 PM Priority Status and Request Reply q • User is composing a message with a priority Menu Option status and a request for a reply. • Messages in the Inbox folder are flagged with ”Priority” and “Request Reply”. Identifying Status Indicators TMS Menu Options Description/Function INBX Brings you to your incoming messages screen. COMP Brings you to the compose screen.
O5Head_6875947M01_C.book Page 21 Wednesday, October 20, 2010 12:13 PM Menu Option Deletes the current selected message. LED Indicator LED indicator shows the operational status of your radio. ALL Selects to delete all the messages in the current folder. YES Deletes all the messages in the current folder. Yellow LED NO Cancel the delete all messages options. Green LED EXIT Exits to the Home screen. OPTN Brings you to the Options main screen.
O5Head_6875947M01_C.book Page 22 Wednesday, October 20, 2010 12:13 PM Intelligent Lighting Indicators This feature temporary changes the radio’s display backlight color and the alert text background color to help signal that a radio event has occurred. Identifying Status Indicators Note: 22 English This feature must be preprogrammed by a qualified radio technician. Backlight Event Orange Emergency Alerts When The radio initiates an emergency alarm or call.
O5Head_6875947M01_C.book Page 23 Wednesday, October 20, 2010 12:13 PM Alert Tones You Hear Tone Name Radio Self Test Fail Reject Short, Low-Pitched Tone Time-Out Timer Warning No ACK Received Individual Call Warning Tone Long, Low-Pitched Tone A Group of Low-Pitched Tones Time-Out Timer Timed Out Talk Prohibit/PTT Inhibit Heard When radio fails its power-up self test. When an unauthorized request is made. Four seconds before time out. When radio fails to receive an acknowledgment.
O5Head_6875947M01_C.book Page 24 Wednesday, October 20, 2010 12:13 PM You Hear Tone Name Valid Key-Press Radio Self Test Pass Short, Medium-Pitched Tone Clear Voice Priority Channel Received Identifying Status Indicators Emergency Alarm Entry Central Echo Long, Medium-Pitched Tone Volume Set Emergency Exit Failsoft Automatic Call Back Talk Permit A Group of Medium-Pitched Tones 24 English Keyfail Console Acknowledge Received Individual Call Heard When correct key is pressed.
O5Head_6875947M01_C.book Page 25 Wednesday, October 20, 2010 12:13 PM You Hear Tone Name Ringing When system is searching for target of Private Call. Enhanced Call Sent When waiting for target of Private Call to answer the call. Phone Call Received When a land-to-mobile phone call is received. Gurgle Dynamic Regrouping (When the PTT button is pressed) a dynamic ID has been received. Unique, Low-Pitched Chirp New Message When a new message is received.
O5Head_6875947M01_C.book Page 26 Wednesday, October 20, 2010 12:13 PM General Radio Operation General Radio Operation Once you understand how your APX Mobile Radio is configured, you are ready to use your radio. Use this navigation guide to familiarize yourself with the basic Call features: Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 26 Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . . . page 27 Receiving and Responding to a Radio Call. . . . . . . . .
O5Head_6875947M01_C.book Page 27 Wednesday, October 20, 2010 12:13 PM Selecting a Radio Channel Use the following procedure to select a channel. Note: Your radio must be preprogrammed to allow you to use this feature. If you select a channel that is not within the preprogrammed band, the radio indicates that it is on an unsupported frequency with both audio and visual warnings. Once you have selected the required channel and/or zone, you can proceed to receive and respond to calls.
O5Head_6875947M01_C.book Page 28 Wednesday, October 20, 2010 12:13 PM Receiving and Responding to a Talkgroup Call To receive a call from a group of users, your radio must be configured as part of that talkgroup. Procedure: When you receive a talkgroup call (while on the Home screen), depending on how your radio is preprogrammed: General Radio Operation 1 ASTRO Conventional Only: The LED lights up solid yellow. The display shows the talkgroup alias or ID, and the caller alias or ID.
O5Head_6875947M01_C.book Page 29 Wednesday, October 20, 2010 12:13 PM 4 Press and hold the PTT button to talk. Release the PTT button to listen. Receiving and Responding to a Telephone Call This feature allows you to receive calls similar to standard phone calls from a landline phone. Note: If you press PTT button before pressing the Menu Select button directly below RESP, your conversation will be heard by all members of the talk group.
O5Head_6875947M01_C.book Page 30 Wednesday, October 20, 2010 12:13 PM Making a Radio Call 2 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. You can select a zone, channel, subscriber ID, or talkgroup by using: • The preprogrammed Zone menu • The Mode Knob • A preprogrammed One Touch button • The Contacts list (see Contacts on page 43).
O5Head_6875947M01_C.book Page 31 Wednesday, October 20, 2010 12:13 PM 5 A telephone-type ringing sounds if the receiving unit is in This feature allows you to send an individual Call Alert or page if there is no answer from the target radio. Your radio must be preprogrammed to allow you to use this feature. 6 Hold the microphone vertically 1 to 2 inches (2.5 to 5.
O5Head_6875947M01_C.book Page 32 Wednesday, October 20, 2010 12:13 PM Making a Telephone Call 6 When your call is answered, press the PTT button to talk. This feature allows you to make calls similar to standard phone calls to a mobile or landline phone. 7 Release the PTT button to listen. Procedure: Press the preprogrammed Quick Access (One-Touch) Phone Call button to dial the preprogrammed phone number and proceed to Step 5. OR Follow the procedure below. General Radio Operation 1 > or < to PHON.
O5Head_6875947M01_C.book Page 33 Wednesday, October 20, 2010 12:13 PM Repeater or Direct Operation The DIRECT or “talkaround operation” allows you to bypass the repeater and connect directly to another radio. The transmit and receive frequencies are the same. Procedure: Press the preprogrammed Repeater/Direct switch to toggle between talkaround and repeater modes. OR Follow the procedure below.
O5Head_6875947M01_C.book Page 34 Wednesday, October 20, 2010 12:13 PM Trunked Modes Only: 1 Press the PTT button. 2 If you hear two, short, high-pitched tones, or if you hear no tone and the t indicator lights steadily, then proceed with your message. 3 Release the PTT button to receive (listen). General Radio Operation If you are not in the range of the system, you may hear a continuous low-pitched tone and the display shows OUT OF RANGE.
O5Head_6875947M01_C.book Page 35 Wednesday, October 20, 2010 12:13 PM Advanced Features Calling a Phone Not in the List 1 > or < to PHON. 2 Press the Menu Select button directly below PHON. 3 Enter the desired phone number from the optional keypad microphone. The display updates as the numbers are entered. 4 Press 3 button on the keypad microphone to make the call. 5 Press and hold the PTT button to talk.
O5Head_6875947M01_C.book Page 36 Wednesday, October 20, 2010 12:13 PM Receiving and Making a Selective Call (Conventional Only) This feature allows you to receive a call from or to call a specific individual. It is intended to provide privacy and to eliminate the annoyance of having to listen to conversations that are of no interest to you. Receiving a Selective Call Procedure: 1 When you receive a Selective Call, you hear two alert tones Advanced Features and the LED lights up solid yellow.
O5Head_6875947M01_C.book Page 37 Wednesday, October 20, 2010 12:13 PM 4 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. The display shows the ID of the target radio. 6 Release the PTT button to listen. 7 Press H to return to the Home screen. If you do not press H button to hang up, your radio will remain in Selective Call state with the other unit. You will miss all subfleet traffic and incoming phone calls.
O5Head_6875947M01_C.book Page 38 Wednesday, October 20, 2010 12:13 PM Sending a Status Call This feature allows you to send data calls to the dispatcher about a predefined status. Each status can have up to a 14-character name. A maximum of eight status conditions is possible. Advanced Features Note: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire.
O5Head_6875947M01_C.book Page 39 Wednesday, October 20, 2010 12:13 PM Procedure: 1 When your radio is dynamically regrouped, it automatically 2 Press the PTT button to talk. Release PTT button to listen. When the dispatcher cancels dynamic regrouping, the radio automatically returns to the zone and channel that you were using before the radio was dynamically regrouped. Requesting a Reprogram This feature lets you notify the dispatcher that you want a new dynamic regrouping assignment.
O5Head_6875947M01_C.book Page 40 Wednesday, October 20, 2010 12:13 PM Multiple Control Head Features Multiple Control Head Features This feature allows a transceiver to control as many as four O5 control heads on APX 7500 and, up to two O5 control heads on APX 6500. You can use the CAN cables to connect in any configuration that does not exceed 131 feet (40 meters) in combined length. Refer the O5 Control Head Installation Manual (HLN6947) for further information.
O5Head_6875947M01_C.book Page 41 Wednesday, October 20, 2010 12:13 PM All Active Mode Note: The multiple control head feature allows only control heads of the same type to be connected. Upon power up, if a control head of a different type is connected to the radio, the radio reports the FATAL error CH MISMATCH on the display of all attached control heads.
O5Head_6875947M01_C.book Page 42 Wednesday, October 20, 2010 12:13 PM The Volume knob, DIM button, Front/Rear (F/R) softkey and Emergency button remain active on the inactive control head, while all other controls are disabled. Emergency footswitch and VIP inputs remain active on the inactive control head. The VIP input control head is configurable in the CPS and VIP should be attached to the control head selected in the CPS. Note: Only two (2) control heads are supported in the one active mode.
O5Head_6875947M01_C.book Page 43 Wednesday, October 20, 2010 12:13 PM Contacts Note: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Contact entries are alphabetically sorted according to entry alias. Each alias can have up to 5 IDs of different call types associated with it.
O5Head_6875947M01_C.book Page 44 Wednesday, October 20, 2010 12:13 PM 7 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 8 Press the PTT button to initiate the call. During the call, the display shows the subscriber alias. 9 Press and hold the PTT button to talk. The LED lights up solid red. OR Release the PTT button to listen. The LED lights up solid green. 10 If there is no voice activity for a programmed period of time, Advanced Features the call ends.
O5Head_6875947M01_C.book Page 45 Wednesday, October 20, 2010 12:13 PM Adding a New Contact Entry 1 > or < to CNTS. 2 Press the Menu Select button directly below CNTS. The entries are alphabetically sorted. 3 > or < to {NEW CONTACT} and press the Menu Select button directly below SEL. 4 The display shows NAME. Press the Menu Select button directly below EDIT. Use the keypad to enter the name. Press < to move one space to the left. Press > to move one space to the right.
O5Head_6875947M01_C.book Page 46 Wednesday, October 20, 2010 12:13 PM Deleting a Contact Entry Adding a Contact to a Call List or Phone List Procedure: Procedure: 1 > or < to CNTS. 1 > or < to CNTS. 2 Press the Menu Select button directly below CNTS. The 2 Press the Menu Select button directly below CNTS. The entries are alphabetically sorted. 3 > or < to the entry you want to delete and press the Menu Select button directly below OPTN.
O5Head_6875947M01_C.book Page 47 Wednesday, October 20, 2010 12:13 PM Editing a Contact in a Call List or a Phone List Procedure: 1 > or < to CNTS. 2 Press the Menu Select button directly below CNTS. The entries are alphabetically sorted. 3 > or < to the entry you want to edit and press the Menu Select button directly below OPTN. 4 > or < to EDIT and press the Menu Select button directly below SEL. 5 > or < to the entry alias you wish to change and press the Menu Select button directly below EDIT.
O5Head_6875947M01_C.book Page 48 Wednesday, October 20, 2010 12:13 PM Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 7 Press the Menu Select button directly below OK once you have finished. The display returns to the Edit Contact screen. 8 Press the Menu Select button directly below DONE to save your changes and return to the main screen for Contacts.
O5Head_6875947M01_C.book Page 49 Wednesday, October 20, 2010 12:13 PM Scan Lists Your radio supports different types of Scan Lists: • Trunking Priority Monitor Scan List • Conventional Scan List • Talkgroup Scan List A maximum of 200 Scan Lists can be programmed in your radio. These lists must be preprogrammed by a qualified radio technician. Viewing a Scan List Procedure: 1 > or < to SCNL. 2 Press the Menu Select button directly below SCNL. 3 > or < to view the members on the list.
O5Head_6875947M01_C.book Page 50 Wednesday, October 20, 2010 12:13 PM 6 Press H to exit scan list programming and return to the Home screen. See Viewing and Changing the Priority Status on page 50 for more information on how to add and/or change the priority of the currently displayed channel in the scan list. Changing the Scan List Status Procedure: 1 Long press the preprogrammed Scan side button. 2 > or < to the member you want to edit.
O5Head_6875947M01_C.book Page 51 Wednesday, October 20, 2010 12:13 PM Scan Turning Scan On While Disregarding the Squelch Code (Conventional Channels Only) Turning Scan On or Off Procedure: Press the preprogrammed Scan button. OR Follow the procedure below. 1 > or < to SCAN. 2 Press the Menu Select button directly below SCAN. 3 The display shows SCAN OFF if scan is disabled. Press the Menu Select button directly below SCAN to enable scan.
O5Head_6875947M01_C.book Page 52 Wednesday, October 20, 2010 12:13 PM If a channel continually generates unwanted calls or noise (termed a “nuisance” channel), you can temporarily remove the unwanted channel from the scan list. To transmit on the selected channel if another channel is active, first turn scan off by pressing the Menu Select button below SCAN momentarily.
O5Head_6875947M01_C.book Page 53 Wednesday, October 20, 2010 12:13 PM Restoring Priorities in a Scan List While the radio is scanning, the dynamic priority change feature allows you to temporarily change any channel in a scan list (except for the Priority-One channel) to the Priority-Two channel. Procedure: This change remains in effect until scan is turned off. Scan then reverts to the preprogrammed (original) setting.
O5Head_6875947M01_C.book Page 54 Wednesday, October 20, 2010 12:13 PM Call Alert Paging This feature allows your radio to work like a pager. Even if other users are away from their radios, or if they are unable to hear their radios, you can send them an individual Call Alert page. You can also verify if a radio is active on the system.
O5Head_6875947M01_C.book Page 55 Wednesday, October 20, 2010 12:13 PM Sending a Call Alert Page If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure: Press the preprogrammed Quick Access (One-Touch) Call Alert Paging button to send a page to the preprogrammed ID and proceed to Step 5 of the procedure below.
O5Head_6875947M01_C.book Page 56 Wednesday, October 20, 2010 12:13 PM Press the Menu Select button directly below OK to return to the main screen for Contacts. Emergency Operation The Emergency feature is used to indicate a critical situation. In-Call User Alert You can enable and disable voice transmission, if needed. Procedure: 1 Make sure you are in Home mode where the default zone and mode are being displayed. Advanced Features 2 > or < to scroll to the VMUT.
O5Head_6875947M01_C.book Page 57 Wednesday, October 20, 2010 12:13 PM Sending an Emergency Call (Trunking Only) This feature allows you to send a data transmission, which identifies the radio sending the emergency, to the dispatcher. Procedure: Procedure: 2 A tone sounds and the display alternates EMERGENCY and 1 Press the preprogrammed Emergency button. A tone sounds and the display alternates EMERGENCY and the home display. 2 A dispatcher acknowledgment ACK RECEIVED display follows.
O5Head_6875947M01_C.book Page 58 Wednesday, October 20, 2010 12:13 PM Procedure: 1 Press the preprogrammed Emergency button to activate the emergency call/alarm feature. 2 The display alternates EMERGENCY and the home display. 3 A high-pitched tone sounds, indicating that the alarm has been received by the trunked system’s central controller. A dispatcher acknowledgment (four high-pitched tones) follows, accompanied by an ACK RECEIVED display. 4 Hold the microphone vertically 1 to 2 inches (2.0 to 2.
O5Head_6875947M01_C.book Page 59 Wednesday, October 20, 2010 12:13 PM Special Considerations for Emergencies no emergency capability, a low-pitched tone sounds. • If the unit is out of the range of the system and/or the emergency alarm is not acknowledged, a tone sounds and the display shows NO ACKNOWLEDGE.
O5Head_6875947M01_C.book Page 60 Wednesday, October 20, 2010 12:13 PM Advanced Features Automatic Registration Service (ARS) Selecting or Changing ARS Mode Procedure: This feature provides an automated data application registration for the radio. When you turn on the radio, the device automatically registers with the server. Data applications within the fixed network can determine the presence of a device on the system and send data to the device. For example: Text Messaging Service (TMS).
O5Head_6875947M01_C.book Page 61 Wednesday, October 20, 2010 12:13 PM Logging In as a User This feature allows you as the user to be associated with the radio. With this association, every data application (Example: Text Messaging Service) takes on a friendly username. Procedure: You can still send text messages without logging in as a user. The user login feature only enables the recipient of your message to identify you as the sender by assigning a username to your message.
O5Head_6875947M01_C.book Page 62 Wednesday, October 20, 2010 12:13 PM The maximum PIN length is 4 digits. The PIN number will appear as asterisks. 8 Press the Menu Select button directly below LOGN. Once the data application registration is completed, you can log out. 9 In ARS server mode, the display shows the User Login Procedure: Indicator icon, the ID, IN PPROGRESS and CNCL. OR In ARS non-server mode, the display shows the User Login Indicator icon, the ID, LOGGED IN and LOGT.
O5Head_6875947M01_C.book Page 63 Wednesday, October 20, 2010 12:13 PM Text Messaging Service (TMS) There are three (3) types of text messages: • A new text message (free form message) • A predefined message (quick text message) Note: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit.
O5Head_6875947M01_C.book Page 64 Wednesday, October 20, 2010 12:13 PM Composing and Sending a New Text Message Note: During the uppercase and lowercase mode, multitapping the keys only scrolls through the letters. For example, A->B->C, a->b->c. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 6 Press the Menu Select button directly below OPTN once the message is composed.
O5Head_6875947M01_C.book Page 65 Wednesday, October 20, 2010 12:13 PM 9 Press the Menu Select button below SEND to send the 10 The display shows the SEND MESSAGE screen and SENDING MSG. 11 If the message is sent, a tone sounds and the display shows MSG SENT. OR If the message is not sent, a low tone sounds and the display shows SEND FAILED. If the message fails to send, the radio returns you to the main TMS screen.
O5Head_6875947M01_C.book Page 66 Wednesday, October 20, 2010 12:13 PM Press > to move one space to the right. Press the Menu Select button directly below DEL to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 7 Press the Menu Select button directly below OPTN. 8 > or < to SEND and press the Menu Select button directly below SEL to send the message.
O5Head_6875947M01_C.book Page 67 Wednesday, October 20, 2010 12:13 PM Using the Priority Status and Request Reply Features Appending or Removing a Priority Status to a Text Message Note: The Priority Message icon on a message does not imply that the message gets higher priority over the other messages when it is being transmitted. It is just an indication that can be embedded into a message to let the receiver know that the message is important.
O5Head_6875947M01_C.book Page 68 Wednesday, October 20, 2010 12:13 PM > or < to RQRP and press the Menu Select button directly Managing Text Messages below RQRP to request for a reply. 3 The priority status and reply status icons appear beside the normal message icon on the label bar. Removing a Priority Status and a Reply Request from a Text Message When an outgoing message is indicated with priority status and reply status icons, follow the procedure below to remove these indicators.
O5Head_6875947M01_C.book Page 69 Wednesday, October 20, 2010 12:13 PM • Select RPLY to reply the message. The Inbox can hold up to thirty (30) messages. • Select DEL to delete the message. Note: > or < to read the message if fills more than one • Select BACK to return to the previous screen. screen. Note: Procedure: Press the preprogrammed Data Feature button or the TMS Feature button to access the TMS feature screen, and proceed to Step 3.
O5Head_6875947M01_C.book Page 70 Wednesday, October 20, 2010 12:13 PM Replying to a Received Text Message Note: The original date and time stamp, address and message content is automatically appended to the reply message. Procedure: 1 > or < to the required aliases or ID and press the Menu Select button below SEL to view the message. 2 Press the Menu Select button directly below RPLY to reply to a message. Advanced Features 3 > or < to NEW and press the Menu Select button directly below NEW.
O5Head_6875947M01_C.book Page 71 Wednesday, October 20, 2010 12:13 PM Managing Sent Text Messages This folder stores the messages that were saved previously. The Drafts folder can hold up to 10 messages. The oldest draft in the folder is deleted when the 11th message comes in. Once a message is sent to another radio, it is saved in the Sent folder. The most recent sent text message is always added to the top of the Sent list.
O5Head_6875947M01_C.book Page 72 Wednesday, October 20, 2010 12:13 PM Press the Menu Select button directly below OPTN, DEL, or BACK to access the option. • Select OPTN to send to the message. • Select DEL to delete the message. • Select BACK to return to the previous screen. Note: The icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) Icons on page 19 for more information.
O5Head_6875947M01_C.book Page 73 Wednesday, October 20, 2010 12:13 PM Deleting Text Messages From the Inbox, Draft, or Sent screen: 1 > or < to scroll through the messages. 2 Press the Menu Select button directly below DEL to view the delete options. 3 Press the Menu Select button directly below CURR to delete the current message. OR Press the Menu Select button directly below ALL to delete all the messages.
O5Head_6875947M01_C.book Page 74 Wednesday, October 20, 2010 12:13 PM 7 When the key has been loaded successfully, the radio sounds a short tone for single-key radios. Loading the Group Encryption Keys Using the Multikey Feature This feature allows the radio to be equipped with different encryption keys and supports the DES-OFB algorithm. There are two types of multikey: Procedure: 1 Attach the KVL to your radio. 2 Press the Menu Select button below TARGET.
O5Head_6875947M01_C.book Page 75 Wednesday, October 20, 2010 12:13 PM Enabling Secure Transmission Procedure: Procedure: 1 > or < to KEY. 1 > or < to SEC and press the Menu Select button directly 2 Press the Menu Select button directly below KEY. The display shows the last user-selected and stored encryption key, and the available menu selections. 3 > or < to scroll through the encryption keys. OR Use the keypad to enter the number of the desired key.
O5Head_6875947M01_C.book Page 76 Wednesday, October 20, 2010 12:13 PM Selecting a Keyset This feature allows you to select one or more groups of several encryption keys from among the available keys stored in the radio. Advanced Features screen.
O5Head_6875947M01_C.book Page 77 Wednesday, October 20, 2010 12:13 PM MDC Over-the-Air Rekeying (OTAR) Page This feature, also known as OTAR, allows the dispatcher to reprogram the encryption keys in the radio remotely. The dispatcher performs the rekey operation upon receiving a rekey request from the user. This feature allows to view or define MDC Over-the-Air Rekeying (OTAR) features.It is applied only when operating in secure encrypted mode and only for conventional communications.
O5Head_6875947M01_C.book Page 78 Wednesday, October 20, 2010 12:13 PM Hear Clear There are two components of Hear Clear. 1 Companding: Reduces the channel noise, e.g. OTA transmission, that is predominantly present in UHF2 and 900 MHz channel with the following features. • Compressor – reduces the background noise flow and the speech signal at transmitting radio. • Expander – expands the speech while the noise flow remains the same at receiving radio.
O5Head_6875947M01_C.book Page 79 Wednesday, October 20, 2010 12:13 PM Enhancing GPS Performance • Between tall buildings or under dense tree-cover Sometimes, the GPS feature may be unable to complete a location calculation successfully. You then see a message indicating that your radio cannot connect to enough visible satellites.
O5Head_6875947M01_C.book Page 80 Wednesday, October 20, 2010 12:13 PM The radio also stores four (4) preprogrammed waypoints. These coordinates cannot be deleted. Programmable Waypoints Preprogrammed Waypoints Fixed location coordinates: • Home User-configurable location coordinates. • Emergency • Last Known Location Advanced Features • Destination Only the alias is editable, not the coordinates. The Home and Destination coordinates are editable.
O5Head_6875947M01_C.book Page 81 Wednesday, October 20, 2010 12:13 PM 8 Press the Menu Select button directly below EXIT to exit The radio also exits the menu if the emergency button is pressed. Saving a Waypoint Procedure: OR While in the current location display: Follow the procedure below to turn off the GPS (This feature is enabled by a qualified radio technician.): 1 Press the Menu Select button directly below OPTN. 1 > or < to LOC. 2 Press the Menu Select button directly below LOC.
O5Head_6875947M01_C.book Page 82 Wednesday, October 20, 2010 12:13 PM 4 Press the Menu Select button directly below OK once you are done. 5 The display shows SAVED AS . OR The display shows SAVED AS HOME. OR The display shows SAVED AS DEST.. 6 Press H or the PTT button (if preprogrammed) to exit this menu. Viewing a Saved Waypoint Advanced Features Procedure: While in the current location display: 1 Press the Menu Select button directly below OPTN. 2 > or < to WAYPOINTS.
O5Head_6875947M01_C.book Page 83 Wednesday, October 20, 2010 12:13 PM Editing the Alias of a Waypoint While in the current location display: 1 Press the Menu Select button directly below OPTN. 2 > or < to WAYPOINTS. 9 The display shows UPDATED. 10 Press H or the PTT button (if preprogrammed) to exit this menu. 3 Press the Menu Select button directly below SEL. Editing the Coordinates of a Waypoint 4 > or < to desired waypoints.
O5Head_6875947M01_C.book Page 84 Wednesday, October 20, 2010 12:13 PM Press the Menu Select button below EDIT to change the number/coordinates. 7 A blinking cursor appears in the EDIT LOCATION screen. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. 8 Press the Menu Select button directly below OK once you Advanced Features are done.
O5Head_6875947M01_C.book Page 85 Wednesday, October 20, 2010 12:13 PM Deleting All Saved Waypoints 1 Press the Menu Select button directly below OPTN. 2 > or < to WAYPOINTS and press the Menu Select button directly below SEL. 3 > or < to desired waypoints and press the Menu Select button directly below OPTN. 4 > or < to DELETE ALL and press the Menu Select button directly below SEL. 5 The display shows ALL SAVED WAYP CONFIRM DEL?. 6 Press the Menu Select button directly below YES to delete.
O5Head_6875947M01_C.book Page 86 Wednesday, October 20, 2010 12:13 PM Using the Location Feature While in Emergency Trunking System Controls Mode When the Emergency feature is activated by pressing the emergency button, the radio exits the Location menu and returns to the home (default) display so that you can see which channel the emergency signal is going out on. However, you may re-enter the Location menu while still in emergency mode, provided that Silent Emergency has not been activated.
O5Head_6875947M01_C.book Page 87 Wednesday, October 20, 2010 12:13 PM SmartZone® OUT OF RANGE when your radio goes out of the range of the system, it can no longer lock onto a control channel. The SmartZone® feature extends communications beyond the reach of a single-trunked site (antenna location) when operating in a SmartZone system. SmartZone units provide expanded wide-area coverage. Procedure: 1 A low-pitched tone sounds.
Advanced Features O5Head_6875947M01_C.book Page 88 Wednesday, October 20, 2010 12:13 PM Locking and Unlocking a Site Viewing and Changing a Site This feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites. This feature should be used with caution, since it inhibits roaming to another site in a wide-area system. This feature allows you to view the number of the current site or force your radio to change to a new one.
O5Head_6875947M01_C.book Page 89 Wednesday, October 20, 2010 12:13 PM Trunked Announcement Procedure: The announcement capability allows you to make announcements to the entire user group, as well as monitor talkgroup calls and other announcements. 1 Press and hold down the preprogrammed Site Search button. OR Press and hold down the Menu Select button directly below RSSI. 2 A tone sounds and the display momentarily shows SCANNING SITE. When the radio finds a new site, it returns to the Home screen.
O5Head_6875947M01_C.book Page 90 Wednesday, October 20, 2010 12:13 PM Initiating an Announcement If your radio has been programmed to allow announcement calls: Procedure: 1 Press the Mode Knob to locate the announcement-group mode. 2 Press the microphone PTT button to initiate the announcement. Ignition Switch Options This feature allows the user to select the radio’s functionality based on the Ignition State of the radio user’s vehicle. The available options are as follows.
O5Head_6875947M01_C.book Page 91 Wednesday, October 20, 2010 12:13 PM Required This option allows the radio to power off when Inactivity Auto Power Off Timer expires, or, when Ignition Auto Power Off Timer expires. Soft Power Off This option allows the user to power on the radio either through Power button presses or when the Ignition is detected. Meanwhile, if the Power button was pressed or the Ignition was removed, the radio will be turned off.
O5Head_6875947M01_C.book Page 92 Wednesday, October 20, 2010 12:13 PM Auto Power Off Timer Auto Power Off feature powers off the radio when no user actions occur during a preprogrammed length of time. There two different version of Auto Power Off: Inactivity Auto Power Off Timer – This timer begins once the radio is power-on. While the timer is active any user interaction with the radio resets the timer.
O5Head_6875947M01_C.book Page 93 Wednesday, October 20, 2010 12:13 PM Selecting the Power Level You can select the power level at which your radio transmits. The radio always turns on to the default setting. Note: This feature must be preprogrammed by a qualified radio technician. Settings: • Select LOW for a shorter transmitting distance and to conserve power. • Select HIGH for a longer transmitting distance.
O5Head_6875947M01_C.book Page 94 Wednesday, October 20, 2010 12:13 PM OR Press the Menu Select button directly below EXIT to exit the screen without making any changes. 5 The radio returns to the Home screen. The profile name on the Home screen indicates the current selected radio profile. Controlling the Display Backlight You can enable and disable keypad tones as needed. Procedure: Press the preprogrammed Keypad Mute button to turn the tones on or off. OR Follow the procedure below.
O5Head_6875947M01_C.book Page 95 Wednesday, October 20, 2010 12:13 PM Using the Time-Out Timer You can enable and disable voice muting of the affiliated trunking talkgroup or selected conventional channel as needed. This feature turns off your radio’s transmitter. You cannot transmit longer than the preset timer setting. Procedure: Press the preprogrammed Voice Mute button to turn the feature on or off. OR Follow the procedure below.
O5Head_6875947M01_C.book Page 96 Wednesday, October 20, 2010 12:13 PM Using the Conventional Squelch Operation Features This feature filters out unwanted calls with low signal strength or channels that have a higher than normal background noise. 1 Procedure: > or < to SQL. 2 Press the Menu Select button directly below SQL. The display shows SQUELCH XX, where XX is the value for the current squelch. Advanced Features 3 Press the Menu Select button directly below “+” to increase the squelch volume.
O5Head_6875947M01_C.book Page 97 Wednesday, October 20, 2010 12:13 PM Using the Smart PTT Feature (Conventional Only) This feature allows you to override any coded squelch (DPL or PL) that might be preprogrammed to a channel. The radio also unmutes to any digital activity on a digital channel. Smart PTT is a per-personality, programmable feature used in conventional radio systems to keep radio users from talking over other radio conversations.
O5Head_6875947M01_C.book Page 98 Wednesday, October 20, 2010 12:13 PM Accessing General Radio Information Your radio contains information on the following: when DVRS is available) • Control Assignments • • • • Note: Note: • Radio Information • IP Display Advanced Features • DVRS DSP Version (only • DVRS CP Version (only when If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire.
O5Head_6875947M01_C.book Page 99 Wednesday, October 20, 2010 12:13 PM Viewing Control Assignments This feature displays the device name, IP address, and status of your radio. This feature displays the programmable radio functions assigned to the controls of your radio for the currently selected channel. Note: The device name of your radio is preprogrammed. Check with your dealer or system administrator for more information. Procedure: Press the preprogrammed Info button and proceed to Step 3.
O5Head_6875947M01_C.book Page 100 Wednesday, October 20, 2010 12:13 PM Using Optional External Alarms (Horn and Lights) Using Permanent Horn and Lights All control heads can be equipped for external alarms (horn and lights) that are activated when a Call Alert page, Private Conversation call, or phone call is received. If Permanent Horn and Lights is enabled, horn and lights will automatically be turned on when the radio powers up.
O5Head_6875947M01_C.book Page 101 Wednesday, October 20, 2010 12:13 PM Receiving a Call While Alarms are Turned On Procedure: When you receive a call with the Alarms turned on: 1 Press the Menu Select button directly below H/L until the Procedure: display shows the required alarm. 2 Press the Menu Select button directly below the required entry and the display exits to Home screen. Press the Menu Select button directly below the entry activates the option. Below are the selections available.
O5Head_6875947M01_C.book Page 102 Wednesday, October 20, 2010 12:13 PM Turning Off Rearmable External Alarms Using the Voice Announcement Procedure: This feature enables the radio to audibly indicate the current feature mode, Zone or Channel the user has just assigned. This audio indicator can be customized per customer requirements. This is typically useful when the user is in a difficult condition to read the content shown on the display.
O5Head_6875947M01_C.book Page 103 Wednesday, October 20, 2010 12:13 PM The two options of priority for the Voice Announcement available are: when the radio is receiving calls. • Low – disables the voice of the feature from announcing when the radio is receiving calls. Procedure: You hear a voice announcement when the features below are preprogrammed in the radio. • The radio powers up. The radio announces the current zone and channel it is transmitting.
O5Head_6875947M01_C.book Page 104 Wednesday, October 20, 2010 12:13 PM Helpful Tips The following are suggestions to assist you in troubleshooting possible operating problems. ! Advanced Features Caution The cables that connect to the rear of the radio could have live voltage on some of their pins. Do not remove or reconnect these cables. Only a qualified radio technician should perform this task.
O5Head_6875947M01_C.book Page 105 Wednesday, October 20, 2010 12:13 PM Accessories http://www.motorola.com/governmentandenterprise On the website, search for APX Mobile Radios. You will see the accessories information besides the specifications of the radio. You can also contact your dealer for details.
Appendix: Maritime Radio Use in the VHF O5Head_6875947M01_C.book Page 106 Wednesday, October 20, 2010 12:13 PM 4 “WE ARE LOCATED AT _______________________.” State the position of the vessel in distress, using any information that will help responders to locate you, e.g.: • latitude and longitude • bearing (state whether you are using true or magnetic north) • distance to a well-known landmark • vessel course, speed or destination 5 State the nature of the distress.
O5Head_6875947M01_C.book Page 107 Wednesday, October 20, 2010 12:13 PM Operating Frequency Requirements • on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.800 MHz frequency • on ships subject to the Safety Convention, the radio must be capable of operating: • in the simplex mode on the ship station transmitting frequencies specified in the 156.025 – 157.
O5Head_6875947M01_C.book Page 108 Wednesday, October 20, 2010 12:13 PM Appendix: Maritime Radio Use in the VHF Table A-1: VHF Marine Channel List (Continued) Frequency (MHz) Channel Number Transmit Receive 24 25 26 27 28 60 * 62 63 * 65 66 67** 68 69 71 72 73 74 75 76 77** 157.200 157.250 157.300 157.350 157.400 156.025 156.075 156.125 156.175 156.225 156.275 156.325 156.375 156.425 156.475 156.575 156.625 156.675 156.725 *** *** 156.875 161.800 161.850 161.900 161.950 162.000 160.625 160.675 160.
O5Head_6875947M01_C.book Page 109 Wednesday, October 20, 2010 12:13 PM Term Glossary Central Controller A software-controlled, computer-driven device that receives and generates data for the trunked radios assigned to it. It monitors and directs the operations of the trunked repeaters. Definition ACK Acknowledgment of communication. Active Channel A channel that has traffic on it. Analog Signal An RF signal that has a continuous nature rather than a pulsed or discrete nature.
O5Head_6875947M01_C.book Page 110 Wednesday, October 20, 2010 12:13 PM Glossary Term Definition Term Definition CP Codeplug Cursor A visual tracking marker (a blinking line) that indicates a location on the display. Failsoft Deadlock Displayed by the radio after three failed attempts to unlock the radio.The radio must be powered off and on prior to another attempt. A feature that allows communications to take place even though the central controller has failed.
O5Head_6875947M01_C.book Page 111 Wednesday, October 20, 2010 12:13 PM Term Multi-System Talkgroup Scan List Check channel activity through menu entries. If the channel is clear, you hear static. If the channel is in use, you hear conversation. It also serves as a way to check the volume level of the radio, since the radio “opens the squelch” when the monitor button is pressed. A scan list that can include both talkgroups (trunked) and channels (conventional).
O5Head_6875947M01_C.book Page 112 Wednesday, October 20, 2010 12:13 PM Term Definition Glossary Any digital P25 traffic having the correct Selective Switch Network Access Code and the correct talkgroup. Squelch Special electronic circuitry, added to the receiver of a radio, that reduces, or cuts off, unwanted signals before they are heard in the speaker. Standby An operating condition whereby the radio’s speaker is muted but still continues to receive data.
O5Head_6875947M01_C.book Page 113 Wednesday, October 20, 2010 12:13 PM Commercial Warranty and Service MOTOROLA COMMUNICATION PRODUCTS I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG: MOTOROLA INC.
O5Head_6875947M01_C.book Page 114 Wednesday, October 20, 2010 12:13 PM INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. Commercial Warranty and Service III. STATE LAW RIGHTS: SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY.
O5Head_6875947M01_C.book Page 115 Wednesday, October 20, 2010 12:13 PM VI. PATENT AND SOFTWARE PROVISIONS: Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software.
O5Head_6875947M01_C.book Page 116 Wednesday, October 20, 2010 12:13 PM Commercial Warranty and Service SERVICE Proper repair and maintenance procedures will assure efficient operation and long life for this product. A Motorola maintenance agreement will provide expert service to keep this and all other communication equipment in perfect operating condition. A nationwide service organization is provided by Motorola to support maintenance services.
O5Head_6875947M01_C.
O5Head_6875947M01_C.book Page 120 Wednesday, October 20, 2010 12:13 PM © 2009, 2010 by Motorola, Inc. All Rights Reserved. 09/10 1301 E. Algonquin Rd., Schaumburg, IL 60196-1078, U.S.A. Printed in the U.S.A.
