MN005720A01-AA Standard Configurations 2.1.2 Wiring Diagrams The following figures show the wiring diagrams for all the possible configurations. Identify which of these figures shows the configuration that you are installing, and use the diagram when planning the installation.
MN005720A01-AA Standard Configurations Figure 25: Radio Installation (O3 Dash Mount) BATTERY (+) FUSE RED LEAD (-) FUSE HORN RELAY LIGHT RELAY SPEAKER IGN SENSE (ACC) DC POWER CABLE P2 (SEE J2 PINOUT) MIC CLIP TRUNNION ANTENNA CONNECTION ANTENNA CONNECTION 20 MOUNTING SCREW DASHMOUNT RADIO ANTENNA CONNECTION J2 REAR ACCESSORY CONNECTOR SPKR+ SPKR- VIPOUT 2 12V (RELAY) IGN SENSE (ACC) VIPOUT 1 12V (RELAY) 26 MIC ANTENNA 3 GPS (OPTIONAL) 3 ft 3 ft FIREWALL HOLE FUSE BLOCK ANTENNA 2
MN005720A01-AA Standard Configurations Figure 27: Radio Installation (O7 Dash Mount) FUSE BATTERY (+) RED LEAD (-) ANTENNA CONNECTION DC POWER CABLE P2 (SEE J2 PINOUT) LIGHT RELAY ANTENNA CONNECTION 20 SPKR+ SPKR- VIPOUT 2 12V (RELAY) IGN SENSE (ACC) VIPOUT 1 12V (RELAY) 26 MOUNTING SCREW MIC ANTENNA CONNECTION J2 REAR ACCESSORY CONNECTOR TRUNNION MIC CLIP SPEAKER 3 ft IGN SENSE (ACC) FUSE HORN RELAY ANTENNA 3 GPS (OPTIONAL) 3 ft FIREWALL HOLE FUSE BLOCK ANTENNA 2 WI-FI (OPTIONAL
MN005720A01-AA Standard Configurations Figure 29: Radio Installation (O3 Remote Mount) FUSE BATTERY (+) RED LEAD (-) FUSE BLOCK P2 (SEE J626 PINOUT) CABLE HLN 6863 LIGHT RELAY 3 ft FIREWALL HOLE DC POWER CABLE ANTENNA CONNECTION connect to P2 3 ft ANTENNA CONNECTION 20 SPKR+ SPKR- VIPOUT 2 12V (RELAY) IGN SENSE (ACC) VIPOUT 1 12V (RELAY) 26 FRONT ACCESSORY CABLE (PMLN4959) EMERGENCY SWITCH ANTENNA CONNECTION J2 REAR ACCESSORY CONNECTOR CH hang up box SPEAKER ANTENNA 3 GPS (OPTIONAL)
MN005720A01-AA Standard Configurations Figure 31: Radio Installation (O7 Remote Mount) FUSE BATTERY (+) PORTS ON REAR OF REMOTE CONTROL HEAD RED LEAD FUSE (-) FUSE YELLOW BLOCK LEAD ANTENNA 1 FUSE HORN RELAY BLACK LEAD 3 ft LIGHT RELAY SPEAKER ANTENNA 2 WI-FI (OPTIONAL) ACC ANTENNA 3 GPS (OPTIONAL) PWR SPK CAN CAN VIP CONNECTOR PIN-OUT 3 ft 10 8 9 MIC FIREWALL HOLE DC POWER CABLE J400 4 2 MIC CLIP 6 7 5 CONTROL HEAD DEK VIP J400 1 VIPCable Radio Function Pin (HKN6196_) Numb
MN005720A01-AA Standard Configurations Figure 33: Radio Installation (O9 Remote Mount with Pinouts) J2 REAR ACCESSORY CONNECTOR 20 SPKR+ 26 7 13 SPKR- VIPOUT 2 12V (RELAY) IGN SENSE (ACC) VIPOUT 1 12V (RELAY) EMERGENCY 21 1 8 GROUND 14 1 VIP CONNECTOR PIN-OUT 2 10 9 8 7 5 4 2 3 6 J400 1 Radio VIP Cable Function Pin (HKN6196_) Number Wire Color J400-1 RED SWB + 4 5 6 No. Description 1 J500 USB 2 J100 M.A.
MN005720A01-AA Standard Configurations Figure 34: Remote Control Head Pinouts 5 4 3 2 6 1 12 No. Description 1 J100 2 J200 3 J300L 4 J300R 5 J400 6 J500 7 USB 8 DEK VIP (YELLOW) 9 CAN (BLUE) 10 CAN (BLUE) 11 PWR SPK (RED) 12 M.A.
MICROPHONE SPEAKER A+ (RED) IGN SENSE (thin RED) FUSE SEE NOTE ACC line VEHICLE IGNITION SWITCH Ignition sense cable uses either 3-amp fuse (6580283E01) or 4-amp fuse (6580283E02) NOTE: See TABLE 2-1 for wiring of the thin RED wire. A good GROUND connection to the car chassis is required for correct radio opearaions.
GROMMET SPEAKER CONTROL HEAD (REAR VIEW) A+ (RED) IGN SENSE (YELLOW) MICROPHONE OPERATOR COMPARTMENT FUSE SEE NOTE ACC line VEHICLE IGNITION SWITCH NOTE: See TABLE 2-1 for wiring of the YELLOW wire. A good GROUND connection to the car chassis is required for correct radio operation.
URC Controller Box REAR CONNECTOR RADIO GCAI to RJ45 Cable Chassis GND (BLK) GROMMET CAN extension cable (BLK) IGN Sense (yellow) A+ (Red) 16A Circuit Breaker 15A, 20A OR 30A FUSE SPEAKER SEE NOTE A+ (Red) ON/ACC VEHICLE IGNITION SWITCH 3A OR 4A FUSE MICROPHONE 15A Fuse RADIO POWER CABLE (RED/BATTERY HOT) Control Head (Rear View) A+ (Red) OPERATOR COMPARTMENT GROMMET (-) VEHICLE BATTERY Chassis GND GROMMET (+) PART OF VEHICLE WIRING Siren Speaker VEHICLE BATTERY COMPARTMENT N
MN005720A01-AA Standard Configurations 2.1.3 Radio Operation Wiring for Dash and Remote Configurations Determine the radio functionality you wish to achieve from the tables in Remote Mount: Power, Ignition, and Emergency Cable Installation on page 42, which is the vehicle ignition switch state is controlling, the physical wiring of the radio ignition sense (ACC) wire, and by the programmed CPS setting.
MN005720A01-AA Standard Configurations emergency accessory is installed, the radio powers up incorrectly into emergency mode all the time. Refer to Figure 83: Emergency Jumper Removal in Remote Mount on page 82 for details. The design of the control head is different compared to the radio. Therefore it is also not necessary to attach HLN6863 to J100 to prevent accidental emergency operation. The control head uses an edgedetect, not a state-detect like on the radio, so mounting of HLN6863 is not mandatory.
MN005720A01-AA Standard Configurations Mid Power Dash/ Remote High-Power Dash/ Remote Transceiver Red Power Wire HLN6863 Thin Red Wire at J2 HLN6863 Thin Red Wire at J626 Transceiver Red Power Wire Connected to ignition switch Ignition switch controls HLN6863 Thin Red Wire at J2 HLN6863 Thin Red Wire at J626 X No ignition switch control. Enables ignition switch functionality as programmed in the codeplug.
MN005720A01-AA Standard Configurations Feature Description Required Soft Power-off Ignition Only Power-up • If IGNITION is not present, all transmissions are inhibited. • The radio is able to affiliate with trunking systems. The radio can ONLY receive trunking dispatch communications. • Emergency Alarm transmissions are possible with the use of the Emergency Power-up feature. • Radio POWERS ON when the Power button is pressed and Ignition is present.
MN005720A01-AA Standard Configurations • For 130 W operation, parallel the two 11 Ω speakers, each rated at 65 W minimum. Proper phasing of the two speakers is important when connecting two speakers in parallel, wire similar speaker terminals together to ensure maximum loudness and prevent "deadspots". For example, if the terminals are marked "1" and "2", connect the terminals marked "1" together and connect those wires to one speaker lead.
MN005720A01-AA Standard Configurations NOTICE: For optimum radio performance, orient the mounting trunnion as shown in the following figures. For new or existing installations of APX 2500, APX 4500, and APX 1500, use only the APX mobile trunnion, kit number HLN6861_. Figure 38: Enhanced Single Band Mobile Radio Trunnion Orientation 1 Applies to radios in dash and remote installations. No. Description 1 Radio Front 2.2.
MN005720A01-AA Standard Configurations Figure 39: Transmission Hump Trunnion Mounting 3 1 1 Figure 40: Below Dash Trunnion Mounting 1 3 2 7 6 1 5 4 Table 7: Mid Power Trunnion Kit 48 Item Part Number Description Mid Power Radio 1 0305760W04 Trunnion Mounting Wing Screw Enhanced Single Band Mobile 2 0312002B14 Self-Drilling Tapping Screw Enhanced Single Band Mobile 3 HLN6861_ ASTRO Trunnion Hardware Kit Enhanced Single Band Mobile 4 - Threaded Hole for Screw - 5 - Groove -
MN005720A01-AA Standard Configurations Item Part Number Description Mid Power Radio 6 - Plastic Guides - 3 Using the trunnion mounting bracket as a template, mark the positions of the holes on the mounting surface. Use the innermost four holes for a curved mounting surface such as the transmission hump, and the four outermost holes for a flat surface such as under the dash. 4 Center punch the spots you have marked and realign the trunnion in position.
MN005720A01-AA Standard Configurations 2.2.2.1.1 Installing Remote Mount Control Head Procedure: 1 Use the control unit trunnion as a template to mark the mounting holes; drill 5/32" holes. If mounting on a plastic surface, use a metal backing plate. 2 Attach the trunnion bracket using all four 10-16" x 5/8" self-tapping screws provided. 3 Temporarily install the control head (adjusting for proper viewing angle) and fasten it to the trunnion with two wing screws.
MN005720A01-AA Standard Configurations Figure 42: O9 Control Head Installation Exploded View 1 6 5 2 4 3 No. Description 1 Adjust the control head to a desired angle and secure with wing screws 2 Mounting surface 3 IMPORTANT: If the trunnion is mounted on a plastic or unstable surface, use a metal backing plate (not supplied).
MN005720A01-AA Standard Configurations Figure 43: O5 Control Head Rear View (Also applicable for O2 and O7 Control Heads) Figure 44: O9 Control Head Rear View 2.2.2.2 Multiple Control Head Installation Install control heads in a multiple control head configuration as per the steps detailed in Installing Remote Mount Control Head on page 50. Two heads can be connected to each of the two CAN connectors on the radio, with the remaining heads connected to one or both of the first two.
MN005720A01-AA Standard Configurations available CAN cable lengths. Control head ground, power and ignition sense wires (black, red, and yellow respectively) may need more length (not supplied) in installations that locate the head more than 10 feet from a power source.
MN005720A01-AA Standard Configurations Figure 45: APX Mobile O5 Control Head Front View O5 1 3 2 No. Description 1 Power button 2 Left-most Soft Menu key 3 Emergency button 3 Press the Power button to power on the control head. Figure 46: Radio Display with Current Control Head ID The head is powered on into FPP mode and displays the current control head ID number. 4 Turn the Mode knob to change the control head ID number.
