MN005720A01-AB Chapter 2: Standard Configurations Figure 31: Radio Installation (E5 Dash Mount) BATTERY (+) FUSE RED LEAD (-) FUSE HORN RELAY LIGHT RELAY SPEAKER IGN SENSE (ACC) ANTENNA CONNECTION DC POWER CABLE P2 (SEE J2 PINOUT) MIC CLIP ANTENNA CONNECTION ANTENNA CONNECTION J2 REAR ACCESSORY CONNECTOR TRUNNION 20 SPKR+ SPKR- VIPOUT 2 12V (RELAY) IGN SENSE (ACC) VIPOUT 1 12V (RELAY) 26 MOUNTING SCREW MIC ANTENNA 3 GPS (OPTIONAL) 3 ft 3 ft FIREWALL HOLE FUSE BLOCK ANTENNA 2 WI-FI
MN005720A01-AB Chapter 2: Standard Configurations NOTICE: In dash mount configuration, it is mandatory that a rear accessory cable is attached to the back of a mid power radio, to ground the Emergency pin to ground (GND). Or, an emergency footswitch or pushbutton switch must be attached to the back of a mid power radio.
MN005720A01-AB Chapter 2: Standard Configurations Figure 35: Radio Installation (O5 Remote Mount) BATTERY (+) (-) FUSE PORTS ON REAR OF REMOTE CONTROL HEAD RED LEAD FUSE FUSE YELLOW BLOCK LEAD ANTENNA 1 FUSE HORN RELAY BLACK LEAD LIGHT RELAY SPEAKER ANTENNA 2 WI-FI (OPTIONAL) 3 ft ACC ANTENNA 3 GPS (OPTIONAL) PWR SPK CAN CAN 10 9 8 7 5 4 2 CONTROL HEAD MIC FIREWALL HOLE DC POWER CABLE USB VIP CONNECTOR PIN-OUT 3 ft MIC CLIP DEK VIP J400 6 J400 1 VIPCable Radio Function Pin
MN005720A01-AB Chapter 2: Standard Configurations Figure 37: Radio Installation (O7 Remote Mount) FUSE BATTERY (+) PORTS ON REAR OF REMOTE CONTROL HEAD RED LEAD FUSE (-) FUSE YELLOW BLOCK LEAD ANTENNA 1 FUSE HORN RELAY BLACK LEAD 3 ft LIGHT RELAY SPEAKER ANTENNA 2 WI-FI (OPTIONAL) ACC ANTENNA 3 GPS (OPTIONAL) PWR SPK CAN CAN 10 9 MIC J400 4 2 MIC CLIP 6 7 5 FIREWALL HOLE DC POWER CABLE USB VIP CONNECTOR PIN-OUT 3 ft 8 CONTROL HEAD DEK VIP J400 1 VIPCable Radio Function Pi
MN005720A01-AB Chapter 2: Standard Configurations Figure 39: Radio Installation (O9 Remote Mount with Pinouts) J2 REAR ACCESSORY CONNECTOR 20 SPKR+ 26 7 13 SPKR- VIPOUT 2 12V (RELAY) IGN SENSE (ACC) VIPOUT 1 12V (RELAY) EMERGENCY 21 1 14 1 VIP CONNECTOR PIN-OUT 2 10 9 8 7 5 4 2 3 6 J400 1 Radio VIP Cable Function Pin (HKN6196_) Number Wire Color J400-1 RED SWB + 4 5 6 No. Description 1 J500 USB 2 J100 M.A.
MN005720A01-AB Chapter 2: Standard Configurations Figure 40: Remote Control Head Pinouts 5 4 3 2 6 1 12 No. Description 1 J100 2 J200 3 J300L 4 J300R 5 J400 6 J500 7 USB 8 DEK VIP (YELLOW) 9 CAN (BLUE) 10 CAN (BLUE) 11 PWR SPK (RED) 12 M.A.
42 MICROPHONE SPEAKER A+ (RED) IGN SENSE (thin RED) FUSE SEE NOTE ACC line VEHICLE IGNITION SWITCH Ignition sense cable uses either 3-amp fuse (6580283E01) or 4-amp fuse (6580283E02) NOTE: See TABLE 2-1 for wiring of the thin RED wire. A good GROUND connection to the car chassis is required for correct radio opearaions.
GROMMET SPEAKER CONTROL HEAD (REAR VIEW) A+ (RED) IGN SENSE (YELLOW) MICROPHONE OPERATOR COMPARTMENT FUSE SEE NOTE ACC line VEHICLE IGNITION SWITCH NOTE: See TABLE 2-1 for wiring of the YELLOW wire. A good GROUND connection to the car chassis is required for correct radio operation.
44 URC Controller Box REAR CONNECTOR RADIO GCAI to RJ45 Cable Chassis GND (BLK) GROMMET CAN extension cable (BLK) IGN Sense (yellow) A+ (Red) 16A Circuit Breaker 15A, 20A OR 30A FUSE SPEAKER SEE NOTE A+ (Red) ON/ACC VEHICLE IGNITION SWITCH 3A OR 4A FUSE MICROPHONE 15A Fuse RADIO POWER CABLE (RED/BATTERY HOT) Control Head (Rear View) A+ (Red) OPERATOR COMPARTMENT GROMMET (-) VEHICLE BATTERY Chassis GND GROMMET (+) PART OF VEHICLE WIRING Siren Speaker VEHICLE BATTERY COMPARTMEN
MN005720A01-AB Chapter 2: Standard Configurations 2.1.3 Radio Operation Wiring for Dash and Remote Configurations Determine the radio functionality you wish to achieve from the tables in Remote Mount: Power, Ignition, and Emergency Cable Installation on page 45, which is the vehicle ignition switch state is controlling, the physical wiring of the radio ignition sense (ACC) wire, and by the programmed CPS setting.
