APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4098 109AB-99FT4098 User / Operational Manual Operational or User’s Manual The manual should include instruction, installation, operator, or technical manuals with required ‘information to the users’. This manual should include a statement that cautions the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
8QWLWOHG IP 3DJH 7XHVGD\ )HEUXDU\ 30 Untitled2.
Untitled2.
SLR_8000_NAG.book Page 1 Tuesday, November 17, 2015 11:38 PM m MOTOTRBO™ SLR 8000 Series Base Station Repeater Quick Start Guide Notations Used in This Manual Note and caution notations are used throughout the text in this publication. These notations are used to emphasize that safety hazards exist, and due care must be taken and observed. CAUTION indicates a potentially hazardous situation which, if not avoided, might result in equipment damage.
SLR_8000_NAG.book Page 2 Tuesday, November 17, 2015 11:38 PM General Safety and Installation Standards and Guidelines WARNING WARNING: For safe installation, operation, service and repair of this equipment, follow the safety precautions and instructions described below, as well as any additional safety information in Motorola’s product service and installation manuals and the Motorola R56 Standards and Guidelines for Communications Sites manual (which can be obtained by ordering CD-ROM 9880384V83).
SLR_8000_NAG.book Page 3 Tuesday, November 17, 2015 11:38 PM • RF energy burn hazard. Disconnect power in the cabinet to prevent injury before disconnecting and connecting antennas. • Shock hazard. The outer shields of all Tx and Rx RF cables outer shields must be grounded per Motorola R56 manual. • Shock hazard. DC input voltage shall be no higher than 60 VDC.
SLR_8000_NAG.book Page 4 Tuesday, November 17, 2015 11:38 PM Part 68 Information Part 68 FCC Guideline This section applies when the SLR 8000 Base Station Repeater is equipped with the optional Wireline Interface Board. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the rear of this equipment is a label that contains, among other information, the registration number: US:ABZNINANSLR8000 If requested, this number must be provided to the telephone company.
SLR_8000_NAG.book Page 5 Tuesday, November 17, 2015 11:38 PM MOTOTRBO SLR 8000 Series Base Station Repeater Supplemental Safety and Installation Requirements ATTENTION! The MOTOTRBO SLR 8000 Series Base Station Repeater must be installed in a suitable, in-building enclosure. A restricted access location is required when installing this equipment into the end system. The Base Station Repeater contains a Class 1 built-in power supply component.
SLR_8000_NAG.book Page 6 Tuesday, November 17, 2015 11:38 PM Environmental Conditions at Intended Installation Site The repeater may be installed in any location suitable for electronic communications equipment, provided that the environmental conditions do not exceed the equipment specifications for temperature, humidity, and air quality. Operating Temperature Range -30°C (-22°F) to +60°C (+140°F) – consider cabinet temperature rise.
SLR_8000_NAG.book Page 7 Tuesday, November 17, 2015 11:38 PM See Figure 2a and Figure 2b for an illustration of the mounting hardware configured for a cabinet installation. The base station/repeater is to be connected to a battery supply that is in accordance with the applicable electrical codes for the end use country; for example, the National Electric Code ANSI/NFPA No.70 for the U.S. Grounding Connect a bonding wire from the repeaters ground screw to the site ground point.
SLR_8000_NAG.book Page 8 Tuesday, November 17, 2015 11:38 PM Connectors Rear Panel Figure 3 illustrates the position of the external connectors located on the back panel of the repeater. Table 1 identifies the connector types as well as the primary function of a connector. 14 15 16 17 18 9 10 3 4 19 20 12 *Optional devices not shown.
SLR_8000_NAG.
SLR_8000_NAG.book Page 10 Tuesday, November 17, 2015 11:38 PM Front Panel LEDs After turning on the repeater power, the seven LEDs on the repeater front panel: 1. Light for approximately one second to indicate that they are functional, then 2. Go off for one second. Archiving Copying the Base Station Repeater Codeplug Data to a Computer Proceed to the Customer Programming Software (CPS) configuration procedures to customize the repeater parameters (e.g., operating frequency, PL, codes, etc.).
SLR_8000_NAG.
SLR_8000_NAG.book Page 1 Thursday, October 22, 2015 3:38 PM M MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademark of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2015 Motorola Solutions, Inc. All rights reserved. Oct 2015. www.motorolasolutions.