BLUETOOTH ADAPTER PMLN5712
FOREWORD ! Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. ATTENTION! The radio is restricted to occupational use only to satisfy ICNIRP/ FCC RF energy exposure requirements.
English OPERATION Attaching the Bluetooth Adapter to the Radio's Universal Connector Below are the steps to attach the Bluetooth Adapter PMLN5712 to the radio’s universal connector: 1. Ensure that the radio is turned off before attaching the Bluetooth Adapter to the radio. 2. Remove the universal connector seal from the side of the radio. 3. Attach the Bluetooth Adapter by hooking it on the radio and securing it with the thumb screw (see Figure 1). 4. The Bluetooth Adapter is ready for use.
LED Status Indication State LED Indication Successful Power Up Blue LED Blink 3 times Blue LED Rapid Blinking Searching for or attempting to pair with surrounding Bluetooth device(s) Attempting to connect with Headset Headset Connected Blue LED Normal Blinking Blue LED Heartbeat Blinking (On for every 4 seconds) Table 1: LED Status Indication 2 English Supported Bluetooth Devices • COTS Headset (recommended headsets: HK200, H790). • Bluetooth 1.3 Earpieces NNTN8125. • Bluetooth 1.
English Bluetooth Adapter Pairing Procedure 1. Place the Bluetooth Device(s) in pairing mode. Refer to the respective Bluetooth Device’s User Manual. 2. To place the Bluetooth Adapter in pairing mode: a.Attach the Bluetooth Adapter to the radio. Refer to “Attaching the Bluetooth Adapter to the Radio's Universal Connector” on page 1. b.Power up the radio while pressing the Bluetooth Adapter’s PTT button. The Bluetooth Adapter provides LED indication when it is powered up.
4 English 3. The Bluetooth Adapter provides LED indication when it attempts to connect with the Headset and a tone is heard on the Headset’s speaker. Press the Call/End button or the PTT button of the Headset to accept the connection request from the Bluetooth Adapter. Refer to “LED Status Indication” on page 2. 4. The Bluetooth Adapter provides LED indication when successfully connected with the Headset. Refer to “LED Status Indication” on page 2. 5.
English Bluetooth Link Lost In the event of interference, or if the Bluetooth Device(s) is out of range, the link between the Bluetooth Adapter and Bluetooth Device(s) may be lost. If the link between the Bluetooth Adapter and Headset is lost, the received audio is automatically routed back to the radio's speaker and the Bluetooth Adapter ends the connection with the Bluetooth PTT Pod (if any).
FOREWORD ! Caution Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. ATTENTION! The radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements.
English OPERATION Attaching the Bluetooth Adapter to the Radio's Universal Connector Below are the steps to attach the Bluetooth Adapter PMLN5712 to the radio’s universal connector: 1. Ensure that the radio is turned off before attaching the Bluetooth Adapter to the radio. 2. Remove the universal connector seal from the side of the radio. 3. Attach the Bluetooth Adapter by hooking it on the radio and securing it with the thumb screw (see Figure 1). 4. The Bluetooth Adapter is ready for use.
LED Status Indication State LED Indication Successful Power Up Blue LED Blink 3 times Blue LED Rapid Blinking Searching for or attempting to pair with surrounding Bluetooth device(s) Attempting to connect with Headset Headset Connected Blue LED Normal Blinking Blue LED Heartbeat Blinking (On for every 4 seconds) Table 1: LED Status Indication 2 English Supported Bluetooth Devices • COTS Headset (recommended headsets: HK200, H790). • Bluetooth 1.3 Earpieces NNTN8125. • Bluetooth 1.
English Bluetooth Adapter Pairing Procedure 1. Place the Bluetooth Device(s) in pairing mode. Refer to the respective Bluetooth Device’s User Manual. 2. To place the Bluetooth Adapter in pairing mode: a.Attach the Bluetooth Adapter to the radio. Refer to “Attaching the Bluetooth Adapter to the Radio's Universal Connector” on page 1. b.Power up the radio while pressing the Bluetooth Adapter’s PTT button. The Bluetooth Adapter provides LED indication when it is powered up.
4 English 3. The Bluetooth Adapter provides LED indication when it attempts to connect with the Headset and a tone is heard on the Headset’s speaker. Press the Call/End button or the PTT button of the Headset to accept the connection request from the Bluetooth Adapter. Refer to “LED Status Indication” on page 2. 4. The Bluetooth Adapter provides LED indication when successfully connected with the Headset. Refer to “LED Status Indication” on page 2. 5.
English Bluetooth Link Lost In the event of interference, or if the Bluetooth Device(s) is out of range, the link between the Bluetooth Adapter and Bluetooth Device(s) may be lost. If the link between the Bluetooth Adapter and Headset is lost, the received audio is automatically routed back to the radio's speaker and the Bluetooth Adapter ends the connection with the Bluetooth PTT Pod (if any).
