Network Router User Manual
Table Of Contents
- Copyright
- Table of Contents
- Introduction
- CHAPTER 1 Overview of Major Capabilities
- CHAPTER 2 Basic Mode Setup
- CHAPTER 3 Advanced Setup
- Access the Expert Web Interface
- Links Bar
- Link: Configure
- Link: Connection
- Link: DHCP Server
- Link: IP Passthrough
- Link: NAT
- Link: IPSec
- IPSec VPN
- Link: Router Password
- Link: Time Zone
- Link: VLAN
- Overview
- Ethernet Switching/Policy Setup
- Link: Wireless
- Enable Wireless
- Wireless ID (SSID)
- Privacy
- Advanced Configuration Options (optional)
- WiFi Multimedia
- Wireless MAC Authorization (optional)
- Link: Status
- DSL
- ATM
- Ethernet
- IP
- LAN
- Wireless
- USB
- Logs
- User List
- Link: Diagnostics
- Link: Remote Access
- Link: Update Router
- From a Server
- Link: Reset Router
- Link: Restart Router
- Basic Mode
- Help
- CHAPTER 4 Basic Troubleshooting
- CHAPTER 5 Command Line Interface
- Overview
- Starting and Ending a CLI Session
- Using the CLI Help Facility
- About SHELL Commands
- SHELL Commands
- About CONFIG Commands
- CONFIG Commands
- Remote ATA Configuration Commands
- DSL Commands
- Bridging Settings
- DHCP Settings
- DMT Settings
- Domain Name System Settings
- IGMP Settings
- IP Settings
- Queue Configuration
- IPMaps Settings
- Network Address Translation (NAT) Default Settings
- Network Address Translation (NAT) Pinhole Settings
- PPPoE /PPPoA Settings
- PPPoE with IPoE Settings
- Ethernet Port Settings
- 802.3ah Ethernet OAM Settings
- Command Line Interface Preference Settings
- Port Renumbering Settings
- Security Settings
- SNMP Settings
- System Settings
- Syslog
- Wireless Settings (supported models)
- VLAN Settings
- VoIP settings
- UPnP settings
- DSL Forum settings
- Backup IP Gateway Settings
- VDSL Settings
- CHAPTER 6 Glossary
- Index
195
CONFIG Commands
set atm [vcc
n
] qos sustained-cell-rate { 1 ...
n
}
If QoS class is set to vbr, then specify the sustained-cell-rate that should apply to the
specified virtual circuit. This value should be less than, or equal to the Peak Cell Rate,
which should be less than, or equal to the line rate.
set atm [vcc
n
] qos max-burst-size { 1 ...
n
}
If QoS class is set to vbr then specify the max-burst-size that should apply to the speci-
fied virtual circuit. This value is the maximum number of cells that can be transmitted at
the Peak Cell Rate after which the ATM VC transmission rate must drop to the Sustained
Cell Rate.
set atm [vcc
n
] vpi { 0 ... 255 }
Select the virtual path identifier (vpi) for VCC n.
Your Service Provider will indicate the required vpi number.
set atm [vcc
n
] vci { 0 ... 65535 }
Select the virtual channel identifier (vci) for VCC n. Your Service Provider will indicate the
required vci number.
set atm [vccn] encap { ppp-vcmux | ppp-llc | ether-llc |
ip-llc | ppoe-vcmux | pppoe-llc }
Select the encapsulation mode for VCC n. The options are:
Your Service Provider will indicate the required encapsulation mode.
ppp-vcmux PPP over ATM, VC-muxed
ppp-llc PPP over ATM, LLC-SNAP
ether-llc RFC-1483, bridged Ethernet, LLC-SNAP
ip-llc RFC-1483, routed IP, LLC-SNAP
pppoe-vcmux PPP over Ethernet, VC-muxed
pppoe-llc PPP over Ethernet, LLC-SNAP