User's Guide
Table Of Contents
- English
- Contents
- List of Figures
- List of Tables
- Legal and Support
- Intellectual Property and Regulatory Notices
- Legal and Compliance Statements
- Warranty and Service Support
- Read Me First
- Radio Care
- Introduction
- Radio Overview
- System Overview
- Getting Started
- 6.1 Charging the Battery
- 6.2 Attaching or Detaching the Battery
- 6.3 Attaching or Detaching the Antenna
- 6.4 Attaching the Universal Connector Cover
- 6.5 Removing the Universal Connector Cover
- 6.6 Cleaning the Universal Connector Cover
- 6.7 Turning the Radio On or Off
- 6.8 Holding Your Radio While Transmitting Audio
- 6.9 Adjusting the Volume
- 6.10 Using the Carry Case
- Home Screen Overview
- Icon-Based Menu Overview
- Basic Radio Operation
- General Radio Settings
- 10.1 Talkaround
- 10.2 Setting Date and Time
- 10.3 Setting Radio Tones and Alerts
- 10.4 Setting Power Levels
- 10.5 Adjusting Display Settings
- 10.6 Setting Squelch Levels
- 10.7 Keypad Lock Options
- 10.8 Setting Languages
- 10.9 Setting the Global Navigation Satellite System
- 10.10 Setting LED Indicators
- 10.11 Password Lock
- 10.12 Setting the Voice Announcement
- 10.13 Text-to-Speech
- 10.14 Setting the Microphone Automatic Gain Control
- 10.15 Setting the Microphone Distortion
- 10.16 Setting the Noise Suppress
- 10.17 Setting the Audio Ambience
- 10.18 Setting Audio Profiles
- 10.19 Setting the Text Entry
- 10.20 Voice Operating Transmission
- Types of Radio Calls
- Phone Calls
- Audio Recording
- Switching Audio Route between Internal Radio Speaker and Wired Accessory
- Connectivity
- 15.1 Wi-Fi Operation
- 15.2 Bluetooth®
- 15.2.1 Turning the Bluetooth On or Off
- 15.2.2 Connecting to Bluetooth Devices
- 15.2.3 Disconnecting from Bluetooth Devices
- 15.2.4 Switching Audio Route between Internal Radio Speaker and Bluetooth Device
- 15.2.5 Viewing Device Details
- 15.2.6 Editing Device Names
- 15.2.7 Deleting Device
- 15.2.8 Bluetooth Profiles
- Emergency Operation
- Man Down (Fall Alert)
- Lone Worker
- Call Alert Operation
- Call Log Features
- Call Queue
- Priority Call
- Contacts Settings
- Call Indicator Settings
- Privacy
- Scan
- Security
- Indoor Location
- Job Tickets
- Text Messaging
- Status Message
- Analog Message Encode
- Analog Status Update
- Auto-Range Transponder System
- Dynamic Caller Alias
- Dynamic Group Number Assignment
- Entering the Front Panel Programming
- Home Channel Reminder
- Monitor Feature
- Remote Monitor
- Radio Check
- Mute Mode
- Received Signal Strength Indicator
- Response Inhibit
- Transmit Inhibit
- Call Preemption
- Voice Interrupt
- Over-the-Air Programming
- Authorized Accessories List
- Français (Canada)
- Déclarations juridiques et de conformité
Chapter 39
Monitor Feature
The feature allows you to remotely activate the microphone of a target radio. You can use this feature
to monitor any audible activity surrounding the target radio.
NOTE: This feature is not applicable in Capacity Plus–Single-Site and Capacity Plus–Multi-Site.
39.1
Monitoring Channels
Procedure:
1 Press and hold the programmed Monitor button.
Your radio shows the following indications:
• You hear the radio activity.
• The yellow LED illuminates.
• The display shows the Monitor icon.
2 To call, press and hold the PTT button.
3 To listen, release the PTT button.
39.2
Permanent Monitor
The Permanent Monitor feature is used to continuously monitor a selected channel for activity.
39.2.1
Setting the Permanent Monitor
Procedure:
Press the programmed Permanent Monitor button.
When your radio enters the mode, your radio shows the following indications:
• An alert tone sounds.
• The yellow LED illuminates.
• The display shows Permanent Monitor On and the Monitor icon.
When your radio exits the mode, your radio shows the following indications:
• An alert tone sounds.
• The yellow LED extinguishes.
• The display shows Permanent Monitor Off.
MN007848A01-AB
Chapter 39 : Monitor Feature
140