APXTM TWO-WAY RADIOS APX 4000 MODEL 2 USER GUIDE APX 4000
m ASTRO® APX™ 4000 Series Digital Portable Radios Quick Reference Card Top Lightbar Microphone RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE FOR PORTABLE TWO-WAY RADIO Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF C a u t i o n Exposure booklet enclosed with your radio. ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements.
Sending an Emergency Call 1 Press the Emergency button. 2 Press and hold the PTT button. Speak clearly into the microphone. 3 Release the PTT button to end call. 8 V O 4 Press and hold Emergency button to exit emergency. To exit emergency at any time, press and hold the Emergency button. Blinks when the battery is low. The more stripes, the stronger the signal strength for the current site (trunking only). Direct radio to radio communication or connected through a repeater.
Declaration of Conformity DECLARATION OF CONFORMITY Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola Solutions, Inc. Address: 1303 East Algonquin Road, Schaumburg, Illinois 60196, U.S.A. Phone Number: 1-800-927-2744 Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. Hereby declares that the product: Model Name: APX 4000 conforms to the following regulations: FCC Part 15, subpart B, section 15.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Contents Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xii Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . .1 Declaration of Conformity . . . . . . . . . . . . . . . . .i Important Safety Information . . . . . . . . . . . . . .ix RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE FOR PORTABLE TWO-WAY RADIOS . . . .ix Software Version . . . . . . . . . . . . . . . . . . . . . . . . x Notice to Users (FCC and Industry Canada) . . . . . . x How to Use This Guide . . . . . .
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 8 Top Lightbar Indications . . . . . . . . . . . . . . . . . . . . .23 Intelligent Lighting Indicators . . . . . . . . . . . . . . . . . 24 Identifying Radio Controls . . . . . . . . . . . . . . . . .9 Radio Parts and Controls . . . . . . . . . . . . . . . . . . . . 10 Programmable Features . . . . . . . . . . . . . . . . . . . . . 11 Assignable Radio Functions . . . . . . . . . . . . . . . . . .
Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Viewing a Scan List . . . . . . . . . . . . . . . . . . . . . . . . 51 Editing the Scan List . . . . . . . . . . . . . . . . . . . . . . . 51 Advanced Features . . . . . . . . . . . . . . . . . . . . . 42 Changing the Scan List Status . . . . . . . . . . . . . . . 52 Viewing and Changing the Priority Status . . . . . . 52 Advanced Call Features . . . . . . . . . . . . . . . . . . . . .
Exiting Man Down Feature . . . . . . . . . . . . . . . . . . . 61 Re-Initiating Man Down . . . . . . . . . . . . . . . . . . . . . 62 Testing the Man Down Feature . . . . . . . . . . . . . . . 62 Sending a Sent Text Message . . . . . . . . . . . . . . . .72 Deleting a Text Message . . . . . . . . . . . . . . . . . . . .72 Deleting All Text Messages . . . . . . . . . . . . . . . . . .73 Automatic Registration Service (ARS) . . . . . . . . . . 63 Selecting or Changing the ARS Mode . . . . . . . . . .
Trunking System Controls . . . . . . . . . . . . . . . . . . . . 85 Using the Failsoft System . . . . . . . . . . . . . . . . . . . .85 Going Out of Range . . . . . . . . . . . . . . . . . . . . . . . .85 Using the Site Trunking Feature . . . . . . . . . . . . . . .85 Locking and Unlocking a Site . . . . . . . . . . . . . . . . .86 Viewing and Changing a Site . . . . . . . . . . . . . . . . .86 Viewing the Current Site . . . . . . . . . . . . . . . . . . . . 86 Changing the Current Site . . . . . . . . . .
Accessing the Battery Info screen . . . . . . . . . . . . 104 Non-Commercial Call Channel . . . . . . . . . . . . . . .114 Accessing the General Radio Information . . . . . . 104 Operating Frequency Requirements . . . . . . . . . . 115 Accessing the Radio Information . . . . . . . . . . . . . 105 Viewing the IP Information . . . . . . . . . . . . . . . . . . 106 Viewing the Control Assignments . . . . . . . . . . . . 106 Voice Announcement . . . . . . . . . . . . . . . . . . . . . . 107 Helpful Tips .
Important Safety Information ! Caution Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements.
Software Version All the features described in the following sections are supported by the radio's software version R09.00.00 or later. See Accessing the Radio Information on page 105 to determine your radio's software version. Check with your dealer or system administrator for more details of all the features supported.
ATTENTION! Pour obtenir une liste d'antennes et d'autres accessoires approuvés par Motorola, consultez le site Web: http://www.motorolasolutions.com/APX Selon la règlementation d'Industrie Canada, cet émetteur radio ne peut être utilisé qu'avec une antenne dont le type et le gain maximal (ou minimal) sont approuvés par Industrie Canada pour cet émetteur.
Computer Software Copyrights Computer Software Copyrights Documentation Copyrights The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program.
Getting Started How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . . . page 1 Notations Used in This Manual . . . . . . . . . . . . . . . . . . . page 1 Additional Performance Enhancement . . . . . . . . . . . . . page 2 What Your Dealer/System Administrator Can Tell You. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3 How to Use This Guide This User Guide covers the basic operation of the APX™ 4000 Portables.
The following special notations identify certain items: Example Description Home button Buttons and keys are shown in bold print or H or as an icon. Phone Getting Started > 2 English Menu entries are shown similar to the way they appear on your radio’s display. This means “Press the right side of the 4-way Navigation button”. Additional Performance Enhancement The following are some of the latest creations designed to enhance the security, quality and efficiency of your radio.
CrossTalk Prevention What Your Dealer/System Administrator Can Tell You Check with your dealer or system administrator for the correct radio settings, if the radio is to be operated in extreme temperatures (less than -30 °C or more than +60 °C), to ensure proper top and front display operation.
Charging the Battery Preparing Your Radio for Use Preparing Your Radio for Use Assemble your radio by following these steps: Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Attaching the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . Attaching the Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . Attaching the Accessory Connector Cover . . . . . . . . . . Attaching the Belt Clip. .
Attaching the Battery With the radio turned off, slide the battery into the radio’s frame until the bottom latch clicks into place. Battery Latch is at the bottom of the battery. Note: If your radio is preprogrammed with volatile-key retention, the encryption keys are retained for approximately 30 seconds after battery removal. Check with your dealer or system administrator for more information. Preparing Your Radio for Use To remove the battery, turn the radio off.
Attaching the Antenna With the radio turned off, set the antenna in its receptacle and turn clockwise to attach it to the radio. Attaching the Accessory Connector Cover The accessory connector is located on the antenna side of the radio. It is used to connect accessories to the radio. Preparing Your Radio for Use Note: To prevent damage to the connector, shield it with the connector cover when not in use. Insert the hooked end of the cover into the slot above the connector.
Attaching the Belt Clip Turning On the Radio Tab To remove the clip, use a flatbladed object to press the belt clip tab away from the radio. Then, slide the clip downward and away from your radio. If the power-up test is successful, you see the Home screen. Note: Preparing Your Radio for Use Press and hold the Multi-Function Knob (MFK) until the radio display lights up, then release the MFK. Align the grooves of the belt clip with those of the radio and press upward until you hear a click.
Note: If the power-up test is successful, but you see Hardware board absent or Hw Board Mismatch. Send your radio to the qualified technician to fix this error. If the power-up test is successful, but you see Hw Board Failed or Man-Down Hw Error, send your radio to the qualified technician to fix this error. Adjusting the Volume Your radio is preprogrammed to reset to medium volume rate, which is Level 12, by default whenever the radio powers up. To increase the volume, turn the MFK clockwise.
Identifying Radio Controls Radio Parts and Controls . . . . . . . . . . . . . . . . . . . . . . page 10 Programmable Features . . . . . . . . . . . . . . . . . . . . . . . page 11 Assignable Radio Functions . . . . . . . . . . . . . . . . . . page 11 Assignable Settings or Utility Functions. . . . . . . . . . page 13 Accessing the Preprogrammed Functions. . . . . . . . . . page 13 Using the Menu Select Buttons . . . . . . . . . . . . . . . . page 14 Using the Navigation Buttons. . . . . . . . . . . . . . .
Radio Parts and Controls 1 Top (Orange) Button* 16 Antenna 2 Top Lightbar 15 LED 21 Identifying Radio Controls 3 Microphone 4 Top Side (Select) Button* 5 Push-to-Talk 14 Bluetooth® Pairing Indicator 20 Microphone 13 Speaker 17 Accessory (PTT) Button 12 Main Display 6 Side Button 1* MultiFunction Knob (MFK)* Connector 19 Battery 11 Menu Select Buttons 7 Side Button 2* 10 Data Feature Button 8 Home Button 10 English 9 4-Way Navigation Button Battery 18 Latch (at the bottom) * These ra
Programmable Features Bluetooth Headset and PTT – Keys up the Bluetooth Headset's microphone. Bluetooth Data Devices – Keys up the Bluetooth data devices. The programmable buttons can be programmed as shortcuts to radio functions or preset channels/groups depending on the duration of a button press: Call Alert – Allows the radio to function like a pager, or to verify if a radio is active on the system. • Press – Pressing and releasing rapidly. Channel – Selects a channel.
Man Down Clear – Clears the alarm of Man Down mode which was triggered when the radio achieves or passes a tilt angle threshold or a combination of the angle threshold and a motion sensitivity level. Message – Enters the current message list. Identifying Radio Controls Mode Select – Long-press programs a button with the radio's current zone and channels; then once programmed, the short press of that button jumps the radio to the programmed zone and channel.
Status – Sends data calls to the dispatcher about a predefined status. Accessing the Preprogrammed Functions You can access various radio functions through one of the following ways: Talkgroup (Conventional Only) – Allows a call from an individual radio to a group of radios. • A short or long press of the relevant programmable buttons. OR Text Messaging Service (TMS) – Selects the text messaging menu. TMS Quick Text – Selects a predefined message. User – Automatically registers with the server.
Using the Menu Select Buttons Using the Navigation Buttons The Menu Select buttons access the menu entries of features. Home Button Note: The H button returns you to the Home (default) screen. In most cases, this is the current mode. Check with your dealer or system administrator for the list of features activated in your radio.
Multi-Function Knob (MFK) Use this button to access data-related features, such as the Text Messaging Service (TMS) feature screen. MFK is the on/off button of your radio. See Turning On the Radio on page 7 for the procedure to power up and down your radio. In addition, there are programmable features available for MFK, which are: 4-Way Navigation Button Use this button to scroll up, down, left or right. Press and release one of the button to scroll from one entry to the next one.
Push-To-Talk (PTT) Button The PTT button on the side of the radio serves two basic purposes : Your radio indicates its operational status through the following: • While a call is in progress, Identifying Status Indicators the PTT button allows your radio to transmit to other radios in the call. Press and hold down PTT button to talk. Release the PTT button to listen. The microphone is activated when the PTT button is pressed. • While a call is not in progress, the PTT button is used to make a new call.
Status Icons O • On = Radio is currently configured for direct radio-to-radio communication (during conventional operation only). • Off = Radio is connected with other radios through a repeater. The following icons are for the front display screen unless indicated otherwise. Receiving Radio is receiving a call or data. Transmitting Radio is transmitting a call or data. Battery For IMPRES battery operation only – the icon shown indicates the charge remaining in the battery.
Priority Channel Scan • Blinking dot = Radio detects activity on channel designated as Priority-One. G • Steady dot = Radio detects activity on channel Identifying Status Indicators k m Secure Operation • On = Secure operation. n l 18 English • Off = Clear operation. • Blinking = Receiving an encrypted voice call. • Off = Location feature is disabled. User Login Indicator (IP Packet Data) • On = User is currently associated with your radio.
MFK is in Mode Change feature Turn the MFK to change the channel/zone. MFK is in Volume Change feature Turn the MFK to turn the volume up or down. Text Messaging Service (TMS) Icons This feature allows you to send and receive text messages. See Text Messaging Service (TMS) on page 65 for more information. Status Icons The following icons appear on your radio’s display when you send and receive text messages. Inbox Full The Inbox is full. Message Sent The text message is sent successfully.
Request Reply r Normal Message User is composing a message with normal priority and without a request for a reply. • Messages in the Inbox folder are flagged with 3/6 Message Index Indicates the index of the current message the user is viewing. Example: If the user is looking at the third message out of a total of 6 messages in the Inbox folder, the icon is displayed as the icon on the left column. Identifying Status Indicators Y Read Message The selected text message in the Inbox has been read.
TMS Menu Options Back Description/Function Brings you back to the previous screen. Clr Deletes all messages. Del Deletes a message. Exit Exits to the Home screen. No Returns to the previous screen. Optn Brings you to the Options main screen. Rply Replies to a message. Sel Send Yes Selects the highlighted command. Sends the message. Updates or saves a command.
% Top Lightbar and LED Indicators Landline phone number. The Top Lightbar and LED indicators show the operational status of the radio. Landline phone number added to a Call List. LED Identifying Status Indicators Incoming call or data. 22 English Outgoing call or data. Incoming emergency call.
Top Lightbar Indications Solid red – Radio is transmitting. The lightbar blinks green when the MFK is using the secondary feature. See Multi-Function Knob (MFK) on page 15 to understand the functionality of MFK. Blinking red – Radio is transmitting at low battery condition. Rapidly blinking red – Radio has failed the self test upon powering up or encountered a fatal error. Solid yellow (Conventional Only) – Channel is busy. Blinking yellow – Radio is receiving a secured transmission.
Intelligent Lighting Indicators This feature temporary changes the color of the Top Lightbar and adds a color bar to the main display screen to help signal that a radio event has occurred. Identifying Status Indicators Note: 24 English This feature must be preprogrammed by a qualified radio technician. Bar Color Notification Orange Emergency Alerts When The radio initiates an emergency alarm or call. The radio receives an emergency alarm or call. The radio battery is low. The radio is out of range.
Alert Tones You Hear Tone Name Radio Self Test Fail Reject Short, Low-Pitched Tone Long, Low-Pitched Tone A Group of Low-Pitched Tones Time-Out Timer Warning No ACK Received Individual Call Warning Tone Heard When radio fails its power-up self test. When an unauthorized request is made. Four seconds before time out. When radio fails to receive an acknowledgment. When radio is in an individual call for greater than 6 seconds without any activity. Man Down Entry When radio initiates Man Down mode.
You Hear Tone Name Valid Key-Press Radio Self Test Pass Identifying Status Indicators Short, Medium-Pitched Tone Clear Voice Priority Channel Received Emergency Alarm /Call Entry Central Echo Long, Medium-Pitched Tone Volume Set Emergency Exit Failsoft Automatic Call Back A Group of Medium-Pitched Tones 26 English Keyfail Console Acknowledge Received Individual Call Heard When a correct key is pressed. When radio passes its power-up self test. At beginning of a non-coded communication.
Tone Name Short, High-Pitched Tone (Chirp) Low-Battery Chirp Fast Ringing Ringing Gurgle Heard When battery is below preset threshold value. When system is searching for target of Private Call. Enhanced Call Sent When waiting for target of Private Call to answer the call. Phone Call Received When a land-to-mobile phone call is received. Dynamic Regrouping (When the PTT button is pressed) a dynamic ID has been received.
You Hear Tone Name IncrementalPitched Tone Bluetooth Paired Identifying Status Indicators DecrementalPitched Tone A Group of Very High-Pitched Tones 28 English Heard When Bluetooth accessory is paired with the radio. Bluetooth Connected When Bluetooth accessory is connected to the radio. Bluetooth Unpaired When Bluetooth accessory is unpaired from the radio. Bluetooth Disconnected When Bluetooth accessory is disconnected from the radio.
Phone Call Display and Alert Prompts You Hear You See When A Long Tone No phone You press the PTT button and the phone system is not available. Press H to hang up. The radio returns to the Home screen. Phone busy The phone system is busy. Press H to exit the phone mode and try your call later. Phone busy When a channel is not available. The radio automatically connects when a channel opens. A Busy Tone – A HighPitched Tone No The call is not acknowledged.
Selecting a Zone General Radio Operation A zone is a group of channels. Once you understand how your APX 4000 Portable is configured, you are ready to use your radio. General Radio Operation Use this navigation guide to familiarize yourself with the basic Call features: Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . . . Receiving and Responding to a Radio Call. . . . . . . . . Making a Radio Call . . . . . . . .
Procedure: Selecting a Radio Channel A channel is a group of radio characteristics, such as transmit/ receive frequency pairs. MFK 1 < or > to Zone. 2 Press the Menu Select button directly below Zone. 3 U or D to the required zone. 4 Press the Menu Select button directly below Sel to confirm the displayed zone. 5 Press the PTT button to transmit on the displayed zone channel. OR Follow the procedure below. 1 < or > to ZnUp or ZnDn. Use the following procedure to select a channel.
If Mode Change is secondary feature of MFK, see Multi-Function Knob (MFK) on page 15 to toggle the function of MFK. Procedure: 1 < or > to ChUp or ChDn. 2 Press the Menu Select button directly below ChUpor ChDn. Turn the preprogrammed MFK to the desired channel. OR Follow the procedure below. 3 Press the PTT button to transmit on the displayed zone and 1 < or > to Chan. Note: 2 Press the Menu Select button directly below Chan. General Radio Operation OR Follow the procedure below.
Using Mode Select Feature There are two methods to save the selected zone and channel: • Softkeys • Programmable buttons and keypad buttons (digit 0 to 9) Note: Your radio must be preprogrammed to allow you to use this feature. Five softkeys are available for you to save the frequent used zone and channel. Procedure: 1 Toggle your zone and channel to the required zone and channel. 2 < or > to MS1, MS2 ... or MS5. 3 Press and hold the Menu Select button directly below the softkey.
Saving a Zone and Channel to a Button All the programmable buttons and keypad digit 0 to 9 buttons allow you to save the frequent used zone and channel. Receiving and Responding to a Radio Call Once you have selected the required channel and/or zone, you can proceed to receive and respond to calls. Procedure: 1 Toggle your zone and channel to the required zone and LED Indicator channel. 2 Press and hold the digit button you desire to program.
Receiving and Responding to a Talkgroup Call Procedure: When you receive a talkgroup call (while on the Home screen), depending on how your radio is preprogrammed: 1 ASTRO Conventional Only: The LED lights up solid yellow. The display shows the talkgroup alias or ID, and the caller alias or ID. OR Trunking Only: The display shows the caller alias or ID. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to respond to the call. The LED lights up solid red.
During the call, the display shows the caller ID (number), if the caller’s name is not in the call list. 4 Press and hold the PTT button to talk. Release the PTT button to listen. 5 Press H or the Call Response button to hang up and return to the Home screen. General Radio Operation See Making a Private Call (Trunking Only) on page 37 for details on making a Private Call.
Making a Radio Call • MFK preprogrammed with channel or zone change • A preprogrammed One Touch Call button 4 ASTRO Conventional Only: The LED lights up solid red. The display shows the talkgroup alias or ID. OR Trunking Only: The LED lights up solid red. • The Contacts list 5 Speak clearly into the microphone. Note: 6 Release the PTT button to listen. The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires.
3 Press the Menu Select button directly below Cnts to scroll through and select the required ID. OR Press the Menu Select button directly below LNum to go to the last number dialed. OR U or D to the required ID. 4 Press the PTT button to start the Private Call. 5 The display shows Calling... . General Radio Operation 6 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 7 When you are connected, the display shows the ID of the target radio.
5 The display shows Calling... . your mouth. 7 When you are connected, the display shows the ID of the target radio. Press and hold the PTT button to talk. Release the PTT button to listen. OR If no acknowledgment is received, the display shows No acknowledge. OR If the target radio does not respond before the time out, the display shows No answer. 8 Press H to return to the Home screen.
Repeater or Direct Operation The REPEATER operation increases the radio’s range by connecting with other radios through a repeater. The transmit and receive frequencies are different. The DIRECT or “talkaround operation” allows you to bypass the repeater and connect directly to another radio. The transmit and receive frequencies are the same. General Radio Operation Procedure: Press the preprogrammed Repeater/Direct button to toggle between talkaround and repeater modes. OR Follow the procedure below.
Conventional Mode Operation Procedure: Your radio may be preprogrammed to receive Private-Line® (PL) calls. Press the preprogrammed Monitor button and proceed to Step 3. OR Procedure: 1 Momentarily press the Monitor button to listen for activity. Follow the procedure below. 1 Select the desired zone and channel. 2 Listen for a transmission. 3 Adjust the Volume Change MFK if necessary. 4 Press and hold the PTT button to transmit. The LED lights up solid red.
Advanced Features Advanced Features Use this navigation guide to learn more about advanced features available with your radio: Advanced Call Features . . . . . . . . . . . . . . . . . . . . . . . page 42 Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 48 Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 51 Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 53 Call Alert Paging . . . . . . . . . . . . .
6 Release the PTT button to listen. Procedure: 7 Press H to hang up and return to the Home screen. Press the preprogrammed Quick Access (One-Touch) Selective Call button to dial the preprogrammed ID and proceed to Step 4. OR Follow the procedure below. Using the Talkgroup Call Feature (Conventional Operation Only) 1 < or > to Call. This feature allows you to define a group of conventional system users so that they can share the use of a conventional channel.
Selecting a Talkgroup Sending a Status Call Procedure: 1 < or > to Tgrp. This feature allows you to send data calls to the dispatcher about a predefined status. 2 Press the Menu Select button directly below Tgrp. The Each status can have up to a 14-character name. A maximum of sixteen status conditions is possible. display shows the last talkgroup that was selected and stored, Sel and Exit. 3 U or D to Preset for the preset preprogrammed talkgroup. OR U or D to the required talkgroup.
6 When the dispatcher acknowledges, you hear four tones 7 Press H to return to the Home screen. No traffic is heard on trunked channels while Status Call is selected. If the radio detects no Status Call activity for six seconds, you will hear an alert tone until you press H or the PTT button. Using the Dynamic Regrouping Feature (Trunking Only) This feature allows the dispatcher to temporarily reassign selected radios to a particular channel where they can communicate with each other.
Requesting a Reprogram (Trunking Only) Classifying Regrouped Radios This feature allows you to notify the dispatcher when you want a new dynamic regrouping assignment. The dispatcher can classify regrouped radios into either of two categories: Select Enabled or Select Disabled. Procedure: • Select-enabled radios are free to change to any available Press the preprogrammed Reprogram Request button to send reprogram request to the dispatcher and proceed to Step 3. OR Follow the procedure below.
Saving a Channel in the Dynamic Zone from List Channel Selection Procedure: 1 < or > to Zone. With the radio in Dynamic Zone, follow the procedure below. 2 Press the Menu Select button directly below Zone. The display shows the Zone screen. 3 U or D to . 4 Press the Menu Select button below Sel. The display returns to Home screen with the selected shown on the screen. OR Press the Menu Select button below Exit.
Deleting a Channel in the Dynamic Zone With the radio in Dynamic Zone, follow the procedure below. Procedure: 1 < or > to ZnPr. Press the Menu Select button directly below ZnPr to enter Program Zone screen. 2 The display shows the dynamic channels list. 3 U or D to the saved dynamic channel. Press the Menu Select button directly below Del. The display shows Channel deleted. 4 Press the Menu Select button below Exit to return to Home Advanced Features screen.
Note: The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit. Making a Private Call from Contacts Note: Your radio must be preprogrammed to allow you to use this feature. Procedure: Use the Options Menu. 1 < or > to Cnts. 2 Press the Menu Select button directly below Cnts. The entries are alphabetically sorted. 3 U or D to the required subscriber alias.
Adding a Contact to a Call List Removing a Contact from a Call List Procedure: Procedure: 1 < or > to Cnts. 1 < or > to Cnts. 2 Press the Menu Select button directly below Cnts. The 2 Press the Menu Select button directly below Cnts. The entries are alphabetically sorted. 3 U or D to the entry you want to add to a call list and press the Menu Select button directly below Optn. 4 U or D to Add to CallLst and press the Menu Select button directly below Sel.
Scan Lists Your radio supports different types of Scan Lists: • Trunking Priority Monitor Scan List • Conventional Scan List • Talkgroup Scan List Please refer to a qualified radio technician for the maximum number of Scan Lists can be programmed in your radio. These lists must be preprogrammed by a qualified radio technician. Viewing a Scan List Procedure: 1 < or > to ScnL. 2 Press the Menu Select button directly below ScnL. 3 U or D to view the members on the list.
6 Press H to exit scan list programming and return to the Home screen. See Viewing and Changing the Priority Status on page 52 for more information on how to add and/or change the priority of the currently displayed channel in the scan list. Changing the Scan List Status Procedure: 1 Long press the preprogrammed Scan List Programming button (side button). 2 The display shows the programming mode icon and the first Advanced Features list member. 3 U or D to the member you want to edit.
Scan Making a Dynamic Priority Change (Conventional Scan Only) Turning Scan On or Off Procedure: Press the preprogrammed Scan button to start or stop scan. OR Follow the procedure below. 1 < or > to Scan. 2 Press the Menu Select button directly below Scan. 3 The display shows Scan off if scan is disabled. Press the Menu Select button directly below Scan to enable scan. OR The display shows Scan on and the scan status icon if scan is enabled.
OR < or > to Nuis. Press the Menu Select button directly below Nuis. 2 The radio continues scanning the remaining channels in the list. Restoring a Nuisance Channel Procedure: To restore the deleted nuisance channel, do one of the following: • Turn the radio off and then turning it on again. Advanced Features OR • Stop and restart a scan via the preprogrammed Scan button or menu. OR • Change the channel via the MFK. 54 English Call Alert Paging This feature allows your radio to work like a pager.
Sending a Call Alert Page The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure: Press the preprogrammed Quick Access (One-Touch) Call Alert Paging button to send a page to the preprogrammed ID and proceed to Step 5. OR Follow the procedure below. OR Press the Menu Select button directly below Ok to return to the Contacts screen.
8 The radio returns to the Home screen. OR Press the Menu Select button directly below Ok to return to the Contacts screen. Emergency Operation The Emergency feature is used to indicate a critical situation. If the Top (Orange) button is preprogrammed to send an emergency signal, this signal overrides any other communication over the selected channel.
Sending an Emergency Call (Trunking Only) This feature allows you to send a data transmission, which identifies the radio sending the emergency, to the dispatcher. This feature gives your radio priority access on a channel. Note: Emergency button press timer by default is set to 1 second. This timer is programmable from 0 – 6 seconds by a qualified technician. Procedure: 1 Press the preprogrammed Emergency button. 2 The display shows Emergency and the current zone or channel.
5 Release the PTT button to end the transmission and wait for a response from the dispatcher. 6 Press and hold the preprogrammed Emergency button for about a second to exit the Emergency Call mode. Sending an Emergency Alarm with Emergency Call Procedure: 4 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 5 Press and hold the PTT button. Speak clearly into the microphone. 6 Release the PTT button to end the transmission and wait for a response from the dispatcher.
Note: For ALL Emergency signals, when changing channels: Man Down • If the new channel is also preprogrammed for • If the new channel is NOT preprogrammed for Emergency, the display shows No emergency, and you hear an invalid tone until you exit the Emergency state or change to a channel preprogrammed for Emergency. Using the Emergency Keep-Alive Feature This feature, when enabled, prevents the radio from being turned off via the MFK when the radio is in the Emergency state.
The Man Down feature has three phases: i ii iii The radio senses the Man Down condition and Pre-Alert Timer is initiated. Man Down condition continues for the time duration defined in the Pre-Alert Timer field. At the end of this time, the radio alerts the user on the Man Down status with an audible alert tone and Man Down text on the screen. The Post-Alert Timer also initiates at this point. Man Down condition continues for the time duration defined in the Post-Alert Timer field.
Triggering Emergency This timer sets the amount of time the radio needs to remain in the Man Down condition before the Emergency alarm is transmitted. When the Post-Alert Timer is initiated, the radio alerts the user with an audible tone and displays the “Man-Down” text. When the user does not clear the Man Down condition and the Post-Alert Timer comes to an end, Emergency Alarm or call is triggered. The radio sends emergency message to units within the same Talkgroup.
Re-Initiating Man Down After exiting the Emergency Operation when the radio is still in Man Down condition (tilted achieving threshold angle or motionless), user must first exit Man Down condition to then reinitiate the Man Down feature. Procedure: Return the radio to the vertical position OR Shake the radio (when motion sensitivity is enabled).
Advanced Automatic Registration Service (ARS) Data applications within the fixed network can determine the presence of a device on the system and send data to the device. For example: Text Messaging Service (TMS). The Automatic Registration Service for the radio consists of two (2) modes: Procedure: Turn the preprogrammed MFK, once the zone you want is displayed, to the desired mode. OR Follow the procedure below. 1 < or > to Chan. 2 Press the Menu Select button directly below Chan.
Accessing the User Login Feature This feature allows you as the user to be associated with the radio. With this association, every data application (Example: Text Messaging Service) takes on a friendly username. You can still send text messages without logging in as a user. The user login feature only enables the recipient of your message to identify you as the sender by assigning a username to your message.
Logging Out Procedure: 1 Press the Menu Select button directly below Logt. 2 The display shows the User Login Indicator icon and Clear private data?. OR If the Delete Messages On Session End feature is enabled, the radio clears the private data and returns to User login Screen. 3 Select Yes to clear all your private data. The display shows momentary Private data cleared. OR Select No to keep your private data.
Accessing the TMS Features Sending a Quick Text Message Note: Quick Text messages are messages that are predefined and usually consist of messages that are used most frequently. The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit. Press the Menu Select button directly below Back at any time to return to the previous screen.
6 Press the Menu Select button directly below Optn. button directly below Sel. 8 U or D to scroll through the address list and highlight the required address. 9 Press the Menu Select button below Sel or the PTT button to send the message. 10 The display shows the Send Message screen and Sending msg. 11 If the message is sent, you hear a tone and the display shows Msg sent. OR If the message is not sent, you hear a low tone and the display shows Send failed. 12 The radio returns to main TMS screen.
Removing a Priority Status from a Text Message Removing a Request Reply from a Text Message Procedure: Procedure: 1 Press the Menu Select button directly below Optn. 1 Press the Menu Select button directly below Optn. 2 U or D to Mark as Normal and press the Menu Select 2 U or D to No Req Reply and press the Menu Select button button directly below Sel to remove the priority status from the message. 3 The display shows the normal message icon on the label bar.
Removing a Priority Status and a Reply Request from a Text Message 1 Press the Menu Select button directly below Optn. Receiving a Text Message Note: 2 U or D to Mark as Normal and press the Menu Select button directly below Sel to indicate the message as normal and no request reply. AND U or D to No Req Reply and press the Menu Select button directly below Sel to request for a reply. 3 The display shows the normal message icon on the label bar.
Viewing a Text Message from the Inbox While on the view message screen, press the Menu Select button directly below Rply, Del, or Back to access the option. The Inbox can hold up to thirty (30) messages. Note: U or D to read the message if fills more than one screen. Advanced Features Procedure: Press the preprogrammed Data Feature button or the TMS Feature button to access the TMS feature screen, and proceed to Step 3.
5 The display shows the Send Message screen and Sending msg. Note: You can append a priority status and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 67 for more information. Managing Sent Text Messages Once a message is sent to another radio, it is saved in the Sent folder. The most recent sent text message is always added to the top of the Sent list. The Sent folder is capable of storing a maximum of ten (10) last sent messages.
Sending a Sent Text Message Deleting a Text Message Procedure: Procedure: 1 Press the Menu Select button directly below Optn while From the Inbox or Sent screen: viewing the message. 2 U or D to Send Message and press the Menu Select button directly below Sel. 3 U or D to scroll through the address list and highlight the required address. 4 Press the Menu Select button below Sel or the PTT button to send the message.
Deleting All Text Messages Press the preprogrammed Data Feature button or the TMS Feature button to access the TMS feature screen, and proceed to Step 3. OR Follow the procedure below. 1 < or > to TMS. 2 Press the Menu Select button directly below TMS to access the TMS feature screen. 3 U or D to Inbox or Sent then press the Menu Select button below Clr to select all messages in the selected folder. 4 The display shows Del All?.
Selecting Clear Transmissions Managing Encryption Procedure: Loading an Encryption Key Press the preprogrammed Secure/Clear button to the secure position. Note: If the selected channel is preprogrammed for clear-only operation – when you press the PTT button, you hear an invalid mode tone and the display shows Clear TX only. Note: Refer to the key-variable loader (KVL) manual for equipment connections and setup. Procedure: 1 Attach the KVL to your radio.
Selecting an Encryption Key This feature allows the radio to be equipped with different encryption keys and supports the DES-OFB algorithm. Procedure: There are two types: • Conventional Multikey – The encryption keys can be tied (strapped), on a one-per-channel basis, through Customer Programming Software. In addition, you can have operatorselectable keys, operator-selectable keysets, and operatorselectable key erasure.
Selecting a Keyset Erasing the Selected Encryption Keys This feature allows you to select one or more groups of several encryption keys from among the available keys stored in the radio. This feature allows you to erase all or selected encryption keys. For example, you could have a group of three keys structured to one keyset, and another group of three different keys structured to another keyset; by changing keysets, you would automatically switch from one set of keys to the other.
Requesting an Over-the-Air Rekey (ASTRO Only) 1 Press and hold the Top Side (Select) button. This feature, also known as OTAR, allows the dispatcher to reprogram the encryption keys in the radio remotely. The dispatcher performs the rekey operation upon receiving a rekey request from the user. 2 While holding Top Side (Select) button down, press the Top Procedure: (Orange) button. 3 The display shows Please wait. 4 When all the encryption keys have been erased, the display shows All keys erased.
MDC Over-the-Air Rekeying (OTAR) Page Hear Clear This feature allows to view or define MDC Over-the-Air Rekeying (OTAR) features.It is applied only when operating in secure encrypted mode and only for conventional communications. In additional to Rekey Requests, OTAR transmissions include Delayed Acknowledgements, and Powerup Acknowledgements. There are two components of Hear Clear. Some of the options selected may also need to be set up at the Key Management Controller (KMC) site to work properly.
The Global Positioning System (GPS) • Inside of buildings, trains, or other covered vehicles • Under any other metal or concrete roof or structure For example, GPS location fixes are very difficult to obtain indoors, in covered locations, between high buildings, or in situations where you have not established a clear broad view of the sky.
Enhancing GPS Performance Sometimes, the GPS feature may be unable to complete a location calculation successfully. You then see a message indicating that your radio cannot connect to enough visible satellites. To maximize the ability of your radio to determine a fix, please note the following guidelines: Programmable Waypoints Preprogrammed Waypoints Fixed location coordinates: • Home User-configurable location coordinates. • Emergency • For your initial fix, hold the radio in the face position.
Accessing the Outdoor Location Feature An ON menu key may be present on the location menu if it is preprogrammed by the dealer or system administrator. Procedure: Press the preprogrammed GPS button to toggle the Outdoor Location feature on or off. OR Follow the procedure below. 1 < or > to Loc. 2 Press the Menu Select button directly below Loc. 3 The display shows Location off. 4 Press the Menu Select button directly below On to obtain a location fix. OR Press the Menu Select button directly below Optn.
Saving a Waypoint Viewing a Saved Waypoint Procedure: Procedure: While in the current location display: While in the current location display: 1 Press the Menu Select button directly below Optn. 1 Press the Menu Select button directly below Optn. 2 U or D to Save as Waypt and press the Menu Select 2 U or D to Waypoints and press the Menu Select button Advanced Features button directly below Sel. OR U or D to Save as Home and press the Menu Select button directly below Sel.
Deleting All Saved Waypoints Procedure: Procedure: While in the current location display: While in the current location display: 1 Press the Menu Select button directly below Optn. 1 Press the Menu Select button directly below Optn. 2 U or D to Waypoints and press the Menu Select button 2 U or D to Waypoints and press the Menu Select button directly below Sel. directly below Sel. 3 The display shows a list of waypoints. 3 The display shows a list of waypoints.
Measuring the Distance and Bearing from a Saved Waypoint Procedure: While in the current location display: 1 Press the Menu Select button directly below Optn. 2 U or D to Dist frm here and press the Menu Select button directly below Sel. 3 The display shows a list of waypoints. 4 U or D to the required waypoint, and press the Menu Select Advanced Features button directly below Sel. 5 The display shows the distance and bearing from the current to the selected coordinates.
Trunking System Controls The failsoft system ensures continuous radio communications during a trunked system failure. If a trunking system fails completely, the radio goes into failsoft operation and automatically switches to its failsoft channel. Procedure: 1 During failsoft operation, your radio transmits and receives in conventional operation on a predetermined frequency. 2 You hear a medium-pitched tone every 10 seconds and the display shows Failsoft.
Locking and Unlocking a Site Viewing and Changing a Site This feature allows your radio to lock onto a specific site. This feature should be used with caution, since it inhibits roaming to another site in a wide-area system. This feature allows you to view the name of the current site or forces your radio to change to a new one. Procedure: Use the preprogrammed Site Lock/Unlock button to toggle the lock state between locked and unlocked. OR Follow the procedure below. 1 < or > to Site.
Mission Critical Wireless - Bluetooth® The use of this feature requires the "Full Feature" expansion board together with the Bluetooth Software. This feature allows your radio to extend its functionality by connecting to external proprietary Motorola Accessories. Procedure: 1 < or > to BT. Press the Menu Select button directly below BT to access the Bluetooth feature screen. 2 U or D to Status and press the Menu Select button directly below On.
Turning the Bluetooth Off Re-Pair Timer Procedure: There are two options for configuring the radio’s Bluetooth pairing type. The type defines the duration the radio and the accessory retain the pairing information. 1 < or > to BT. Press the Menu Select button directly below BT to access the Bluetooth feature screen. 2 U or D to Status and press the Menu Select button directly below Off. The display shows Status Off, and b disappears.
Bluetooth Drop Timer Re-Pair Timer Scenarios • When the radio is powered OFF, pairing key is lost immediately, and accessory attempts to pair again. If pairing is unsuccessful within the Drop Timer value, the accessory automatically powers OFF. Immediate (for headset and PTT only) • When the accessory is powered OFF, all keys are lost immediately, and the user must re-pair the devices. The Bluetooth Drop Timer has two different settings and functions, depending upon the selection of the Re-Pair Timer.
Pairing Bluetooth Device with the Radio Procedure: Note: Bluetooth Pairing Location Bluetooth tones, Bluetooth menu and Preprogrammed buttons must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information.
Indicating Bluetooth Connection is Lost The radio shows a when the devices have a Bluetooth connection. Below is the scenario and radio indications when the connection is interrupted. Procedure: 1 The a starts blinking for up to 10 seconds. You hear a decremental-pitched tone and the display shows alternating with disconnected. Turning On the Bluetooth Audio (Routing the Audio from the Radio to the Headset) Procedure: 1 < or > to BT.
Turning Off the Bluetooth Audio (Routing the Audio from the Headset to the Radio) Adjusting the Volume of the Radio from Bluetooth Audio Device Procedure: Procedure: 1 < or > to BT. Press the Menu Select button directly below With the Bluetooth audio device connected to the radio: BT to access the Bluetooth feature screen. 2 U or D to Bluetooth spkr and press the Menu Select button directly below Off. The display shows Off. 1 Adjust volume up/down on the bluetooth audio device.
Press the Menu Select button directly below Back to return to the previous screen. button directly below Clr. 5 The display shows clear?. 6 Press the Menu Select button directly below Yes to proceed. OR Press the Menu Select button directly below No to return to previous screen. 7 The display shows cleared to indicate clearing is successful. OR You hear the radio sounds a short, low-pitched tone. The display shows clear failed.
Viewing the Bluetooth Friendly Name Note: Your radio must be preprogrammed to allow you to use this feature. Procedure: 1 < or > to BT. Press the Menu Select button directly below BT to access the Bluetooth feature screen. 2 U or D to Friendly Name. The display shows Friendly Advanced Features name and the preprogrammed .
3 If the upgrade is successful, the display shows Program done. OR If the upgrade failed, the display shows Program failed. The radio remains in current configuration. Utilities Advanced Features Press the Menu Select button below Dlay to delay the request to upgrade. The radio prompts to upgrade in the next power up of your radio. OR Press the Menu Select button below Rej to reject the request to upgrade. The display shows Upg Aborted.
2 Press the Menu Select button directly below Rcnt to access the Recent Calls feature screen. 3 U or D to scroll through the list. 4 Press the Menu Select button directly below Exit to return to the Home screen. OR Press H or the PTT button to return to the Home screen. Advanced Features The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit.
Selecting a Radio Profile 5 The radio returns to the Home screen. The profile name on the Home screen indicates the current selected radio profile. This feature allows you to display or hide the radio alias (name). Please refer to a qualified technician for more information. Procedure: Note: 1 Press the Menu Select button directly below MyID. The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires.
Selecting the Audio Speaker Procedure: This feature allows you to select the speaker route for the radio's audio from either the main or the secondary speaker using the radio profile settings. Use the preprogrammed Profile button and proceed to Step 3. OR Follow the procedure below. Note: 1 < or > to Prfl. Your radio must be preprogrammed to allow you to use this feature.
Locking and Unlocking the Keypad and Controls You can enable or disable the radio’s display backlight as needed, if poor light conditions make the display difficult to read. You can lock your radio’s keypad, programmable buttons and MFK to avoid inadvertent entry. Check with your dealer or qualified technician for best selection to suite your usage. Depending on how your radio is preprogrammed, you can also maintain a minimum backlight level on the radio's front display.
The display shows momentary Tones on, and you hear a short tone, indicating that the keypad tones are enabled. Turning Voice Mute On or Off You can enable and disable voice transmission, if needed. Procedure: Press the preprogrammed Voice Mute button to turn the feature off or on. OR Follow the procedure below. Advanced Features 1 < or > to VMut. Using the Time-Out Timer This feature turns off your radio’s transmitter. You cannot transmit longer than the preset timer setting.
Setting the Time and Date Settings: • The default time setting is a 12-hour clock.The display shows 12:00AM. • The AM/PM selection is not available for the 24-hour clock setting. • The default setting for the domestic date shows MDY. Note: Check with your dealer or system administrator for additional programmable settings for this feature. Editing the Time and Date Procedure: 1 < or > to Clck. 2 Press the Menu Select button directly below Clck. The display shows the current setting of the radio.
Using the Conventional Squelch Operation Features This feature filters out unwanted calls with low signal strength or channels that have a higher than normal background noise. Analog Options Mode Result Carrier squelch (C) You hear all traffic on a channel. Advanced Features 102 English One or more of the following options may be preprogrammed in your radio. Check with your dealer or system administrator for more information.
Using the Smart PTT Feature (Conventional Only) This feature allows you to override any coded squelch (DPL or PL) that might be preprogrammed to a channel. The radio will also unmute to any digital activity on a digital channel. Smart PTT is a per-personality, programmable feature used in conventional radio systems to keep radio users from talking over other radio conversations. Procedure: When smart PTT is enabled in your radio, you cannot transmit on an active channel.
Mode Description Quick-Key Override This feature can work in conjunction with either of the two above variations. You can override the transmit-inhibit state by quick-keying the radio. In other words, two PTT button presses within the preprogrammed time limit. Advanced Features IMPRES™ Battery Annunciator 2 Press the Menu Select button directly below Batt. The display shows the details of the battery. 3 U or D to scroll through the various information.
Accessing the Radio Information Host Version Secure Version Model Number ESN Flash Code Tuning Version Option Board Type (optional) • Option Board Bluetooth Address (optional) • Expansion Board Type • • • • • • • KG (Secure Algorithm) 1 < or > to Info. Serial Number Flash Size & Type RF Band 2 Press the Menu Select button directly below Info. 3 U or D to Radio Info and press the Menu Select button directly below Sel.
Viewing the IP Information Viewing the Control Assignments This feature displays the device name, IP address, and status of your radio. This feature displays the programmable radio functions assigned to the controls of your radio for the currently selected channel. Advanced Features Note: The device name of your radio is preprogrammed. Check with your dealer or system administrator for more information.
Voice Announcement Each voice announcement is within a limit of three seconds maximum. The sum total duration for all voice announcements in a radio shall be no more than 1000 seconds. Note: This feature must be preprogrammed by a qualified radio technician. Check with your agent if Voice Announcement is available for the feature you need. The two options of priority for the Voice Announcement available are: • High – enables the voice of the feature to announce even when the radio is receiving calls.
Helpful Tips Helpful Tips Take a moment to review the following: Caring for Your Radio . . . . . . . . . . . . . . . . . . . . . . . . page 108 Cleaning Your Radio . . . . . . . . . . . . . . . . . . . . . . . page 109 Handling Your Radio . . . . . . . . . . . . . . . . . . . . . . . page 110 Servicing Your Radio . . . . . . . . . . . . . . . . . . . . . . . page 110 Taking Care of the Battery. . . . . . . . . . . . . . . . . . . . . .page 111 Checking the Battery Charge Status . . . . . . . . . . . .
Caution maximum depth of 1 meter, with a maximum submersion time of 30 minutes. Exceeding either maximum limit may result in damage to the radio. • If the radio battery contact area has been submerged in water, dry and clean the radio battery contacts before attaching a battery to the radio. Otherwise, the water could short-circuit the radio. • If the radio has been submerged in water, shake the radio well so that any water that may be trapped inside the speaker grille and microphone port can be removed.
Handling Your Radio Servicing Your Radio • Do not pound, drop, or throw the radio unnecessarily. Never Proper repair and maintenance procedures will assure efficient operation and long life for this product. A Motorola maintenance agreement will provide expert service to keep this and all other communication equipment in perfect operating condition. A nationwide service organization is provided by Motorola to support maintenance services.
Taking Care of the Battery Your radio can indicate the battery’s charge status through: • the LED and sounds. • the fuel gauge icon on the display. You can also check the battery charge status via the menu entry. See IMPRES™ Battery Annunciator on page 104 for more information. LED and Sounds 0 A blinking fuel gauge icon ( ) is displayed only when the battery voltage drops to low level. In this case, replace the battery with a fully charged one.
Battery Recycling and Disposal In the U.S. and Canada, Motorola participates in the nationwide Rechargeable Battery Recycling Corporation (RBRC) program for battery collection and recycling. Many retailers and dealers participate in this program. Helpful Tips For the location of the drop-off facility closest to you, access RBRC's Internet web site at www.rbrc.com or call 1-800-8BATTERY.
Accessories http://www.motorolasolutions.com/APX 1 Only the following programming cables are compatible with APX 4000 radios. – APX DMR Port Programming Cable (PMKN4012B) – Test and Alignment Programming Cable (PMKN4013C) Accessories The accessory link below is for APX radios. Not all accessories are FCC certified for operation with all APX models and/or bandsplits.
Appendix: Maritime Radio Use in the VHF Frequency Range State the position of the vessel in distress, using any information that will help responders to locate you, e.g.: Appendix: Maritime Radio Use in the VHF Frequency Range 5 • latitude and longitude • bearing (state whether you are using true or magnetic north) • distance to a well-known landmark • vessel course, speed or destination State the nature of the distress. 6 Specify what kind of assistance you need.
Operating Frequency Requirements • on ships subject to the Safety Convention, the radio must be capable of operating: • • in the simplex mode on the ship station transmitting frequencies specified in the 156.025 – 157.425 MHz frequency band, and in the semiduplex mode on the two frequency channels specified in the table below. Note: Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters.
Appendix: Maritime Radio Use in the VHF Frequency Range Table A-1: VHF Marine Channel List (Continued) Frequency (MHz) Channel Number Transmit * 157.150 24 157.200 161.800 25 157.250 161.850 26 157.300 161.900 27 157.350 28 157.400 60 116 English Table A-1: VHF Marine Channel List (Continued) Frequency (MHz) Receive Channel Number Transmit Receive 161.750 75 *** *** 76 *** *** 77** 156.875 – 78 156.925 161.525 161.950 79 156.975 161.575 162.000 80 157.025 161.
Term Glossary Term Bluetooth pairing occurs when two bluetooth devices exchanged a passkey to form a paired Bluetooth wireless connection. Call Alert Privately page an individual by sending an audible tone. Carrier Squelch Feature that responds to the presence of an RF carrier by opening or unmuting (turning on) a receiver’s audio circuit. A squelch circuit silences the radio when no signal is being received so that the user does not have to listen to “noise”.
Glossary Term 118 Definition Conventional Typically refers to radio-to-radio communications, sometimes through a repeater (see Trunking). Conventional Scan List A scan list that includes only conventional channels. CP Codeplug Cursor A visual tracking marker (a blinking line) that indicates a location on the display. Digital Private Line (DPL) A type of coded squelch using data bursts. Similar to PL except a digital code is used instead of a tone.
Term Menu Entry Monitor Multi-Function Knob Term Definition A life-saving feature that senses the radio user may be in trouble by monitoring the whether the radio is in a vertical or horizontal position or whether the radio is motionless. When this feature is triggered, the radio alerts the user with audio and visual alerts. It can also trigger Emergency Alarm if enabled. Multi-System Talkgroup Scan List A scan list that can include both talkgroups (trunked) and channels (conventional).
Glossary Term Definition Term Definition Squelch Special electronic circuitry, added to the receiver of a radio, that reduces, or cuts off, unwanted signals before they are heard in the speaker. SSI Synchronous Serial Interface Push-To-Talk – the PTT button engages the transmitter and puts the radio in transmit (send) operation when pressed. Standby An operating condition whereby the radio’s speaker is muted but still continues to receive data.
Definition Trunking Priority Monitor Scan List A scan list that includes talkgroups that are all from the same trunking system. USK Unique Shadow Key. UTC Coordinated Universal Time. The international time standard (formerly Greenwich Mean Time, or GMT). Zero hours UTC is midnight in Greenwich, England, which is located at 0 degrees longitude. Everything east of Greenwich (up to 180 degrees) is later in time; everything west is earlier.
Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Commercial Warranty Limited Warranty MOTOROLA COMMUNICATION PRODUCTS Commercial Warranty I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG: 122 MOTOROLA SOLUTIONS INC.
INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights which may vary from state to state. IV.
Commercial Warranty VI.
VIII. FOR AUSTRALIA ONLY: Our goods come with guarantees that cannot be excluded under the Australia Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Commercial Warranty Notes 126 English
Motorola Solutions, Inc. 1303 East Algonquin Road Schaumburg, Illinois 60196 U.S.A. MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2011–2012 Motorola Solutions, Inc. All rights reserved. November 2012.
