Mobile Laptop 850™ Model L3391, L3392. Motorola, Inc. Commercial, Government and Industrial Solutions Sector All rights reserved Owner’s Manual Part No.
TRADEMARKS All brand and product names are trademarks or registered trademarks of their respective companies. NOTE Information in this manual is subject to change without notice.
Regulations Information Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Please note: The use of a non-shielded interface cable with this equipment is prohibited. Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
"SAFE USAGE NOTIFICATION: For reasons of personal safety and optimal radio performance, Motorola has designed the ML850 with an intended purpose and position of use either in a secured vehicle docking station or on the top of an office desk. Motorola strongly recommends using this product in a vehicle only when it is physically-secured in a locked or assured-stationary location as failure to do so may cause the product to cause harm in accidents or other conditions.
About the Battery Caution Texts Concerning Lithium Batteries DANISH ADVARSEL! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren. NORWEGIAN ADVARSEL: Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruksjoner.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT : Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
FRENCH ATTENTION: II y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d’un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. Attention (for USA Users) The product that you have purchased contains a rechargeable battery. The battery is recyclable.
Caution (for USA Users) To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord. Power Supply Cord: (optional) Detachable, minimum 1.5 m long. Listed, rated minimum 125 V, 7 A, having a 2/18 AWG, type SVT flexible cord. One end terminates with a parallel blade, molded-on, attachments plug with a 7 A, 125 V (NEMA 1-15P) configuration; other end terminates with a molded-on appliance coupler. Alternate: (optional) Detachable, maximum 4.5 m (14.76 ft) long.
Table of Contents Preface ........................................................................................v Chapter 1 Getting Started .....................................................1-1 Getting the Computer Running..............................................1-2 Unpacking .......................................................................1-2 Connecting to AC Power .................................................1-2 Opening the Cover ........................................................
Chapter 2 Operating Your Computer ...................................2-1 Starting and Stopping the Computer ......................................2-2 Starting the Computer......................................................2-2 Stopping the Computer ....................................................2-2 Using the Keyboard ..............................................................2-4 Typewriter Keys ..............................................................2-4 Cursor-control Keys...................
Using the Communication Features.....................................2-21 Using the Modem ..........................................................2-21 Using the LAN...............................................................2-21 Using the Wireless LAN .....................................................2-22 Configuring the WLAN..................................................2-22 Chapter 3 Managing Power...................................................3-1 AC and Car Adapter........................
System Memory Upgrade......................................................4-7 Chapter 5 Setup Configuration Utility (SCU) .......................5-1 When and How to Use the SCU Program ..............................5-2 When to Use ....................................................................5-2 Starting SCU....................................................................5-2 Moving Around and Making Selections ...........................5-4 Main Menu ..............................................
General Guidelines ..........................................................7-3 Cleaning Guidelines.........................................................7-4 Battery Pack Guidelines...................................................7-4 When Traveling ....................................................................7-5 Chapter 8 Troubleshooting ...................................................8-1 Preliminary Checklist............................................................
Other Problems..............................................................8-14 Resetting the Computer.......................................................8-15 Appendix A Specifications.................................................. A-1 Preface This manual contains information that will help you operate the computer. It is divided into 8 chapters and an appendix. Chapter 1, Getting Started, takes you through the process of setting up the computer and identifying its external components.
Notational Conventions Throughout this manual, the following conventions are used to distinguish elements of text. NOTE: identifies additional information that requires special attention. CAUTION: identifies important information which, if not followed, may result in loss of data or damage to the computer. Keyboard keys are shown in a bold typeset. For example: Press Enter to complete.
COMPUTER SOFTWARE COPYRIGHTS The Motorola products described in this instruction manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including the exclusive right to copy or reproduce in any form the copyrighted computer program.
I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG: Motorola Inc. or if applicable, Motorola Canada Limited ("Motorola",) warrants the Motorola manufactured radio communications product, including original equipment crystal devices and channel elements ("Product"), against material defects in material and workmanship under normal use and service for a period of Three (3)Years from the date of shipment.
Motorola cannot be responsible in any way for any ancillary equipment not furnished by Motorola which is attached to or used in connection with the product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, Motorola disclaims liability for range, coverage, or operation of the system as a whole under this warranty. II.
IV. WHAT THIS WARRANTY DOES NOT COVER: A) Defects or damage resulting from use of the Product in other than its normal and customary manner. B) Defects or damage from misuse, accident, water, or neglect. C) Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment. D) Breakage or damage to antennas unless caused directly by defects in material workmanship.
V. GOVERNING LAW In the case of a Product sold in the United States and Canada, this Warranty is governed by the laws of the State of llli-nois and the Province of Ontario respectively. VI.
Motorola will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or its parts furnished hereunder with software, apparatus or devices not furnished by Motorola, nor will Motorola have any liability for the use of ancillary equipment or software not furnished by Motorola which is attached to or used in connection with the Product.
NOTE: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial or residential environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
CHAPTER 1 Getting Started Congratulations on purchasing this industrial notebook computer. It’s rugged, compact, and portable design allows you to use it in the field or inside a vehicle and other demanding situations where conventional notebook computers just cannot measure up. It can also connect with a docking station to extend the capabilities of input/output devices. This chapter first tells you step by step how to get the computer up and running.
Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation.
1. Make sure the computer is turned off. 2. Plug the DC cord of the AC adapter to the power connector on the computer. NOTE: When the computer is attached to the docking station, connect the DC cord to the power connector on the docking station instead. 3. Plug the female end of the AC power cord to the AC adapter and the male end to an electrical outlet. 4.
Closing the Cover When closing the cover, make sure that the hook is latched properly to safeguard against the following: z To prevent damage to the LCD screen during transport. z To prevent the computer from accidentally waking up from Suspend mode during transport without the user’s knowledge. Turning On and Off the Computer Turning On 1. Make sure the computer / docking station is connected to AC power. 2. Press the power button. Power 3.
Turning Off To turn off the computer power, use the “Shut Down” command of your operating system. NOTE: There are other ways you can stop the computer so that you will be back to where you left off when you next turn on the computer. (See “Stopping the Computer” in Chapter 2 for information.) CAUTION: If you have to turn the computer on again immediately after turning it off, wait for at least five seconds. Turning the computer off and on rapidly can damage it.
Ref Component Description See Also Battery Charge Indicator: – glows green when the battery is fully charged. – Glows orange when the battery is being charged. – Is dark when battery has no charge left and AC adapter is connected and powered on. System State Indicator: – glows green when the computer is powered on. – Glows orange when the computer is in Suspend mode. AC Power Indicator – glows green when computer is connected to AC power and is powered-on.
Left-Side Components Ref Component n Audio Output Connector Connects a hi-fi set, radio set, synthesizer, walkman, etc. o Microphone In Connector Connects an external microphone.
Rear Components Ref Component Description n USB Port Each of the two ports connects a USB device, such as a USB floppy drive, printer, digital camera, joystick, and more. o VGA Port Connects an external monitor. p Serial Port Connects a serial device, such as mouse. q Power Connector Connects the AC adapter.
Front Components Ref Component Description Œ Notched Hole Allows you to hook the computer to the docking station. • Wireless Modem or GSM Antenna Serves as the antenna for the optional wireless modem or GSM/GPRS, CDMA etc.. Ž Touchscreen Pen Provides a convenient way to use the touchscreen. Can be stretched for better grip and handing. • Top Cover Latch Locks the top cover. • Wireless LAN Antenna Serves as the antenna for the Wireless LAN.
Ref Component Description See Also n Speaker Sends out sound and voice from the computer. o Battery Compartment Cover Open the cover to access the battery pack. p Battery Cover Latch Locks the battery compartment. q Docking Connector Serves as the interface between the docking station and the computer.
Top-Open Components Ref Component Description n LCD Screen o Device Indicators Shows the current status of the computer’s devices. See Also Displays the output of the computer. Caps Lock Indicator – glows green when Caps Lock key is pressed and its function is activated. Num Lock Indicator– glows green when Num Lk key is pressed and its function is activated. Scroll Lock Indicator – glows green when Scroll Lk key is pressed and its function is activated.
LAN 10/100 Indicator – glows orange when LAN speed is 10 MBPS – glows green when LAN speed is 100 MBPS Hard Disk Drive Indicator (includes Floppy Disk Drive or CD-ROM Drive In-use Indicator when computer is connected to docking station) Ž Keyboard Serves as the data input device of the computer. • Touchpad Serves as the pointing device of the computer. • Power Button Turns the computer power ON and OFF.
CHAPTER 2 Operating Your Computer This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the operating basics. If you are already a computer user but are new to notebook computers, you may choose to read only the parts containing information unique to your computer.
Starting and Stopping the Computer There are a number of ways to start and stop the computer. Starting the Computer You always start the computer using the power button. A computer starts up with an operating system (OS) existing on the storage device such as the hard disk; or from a floppy disk or CD if you have the docking station installed. The computer will automatically load the OS after you turn it on. This process is called booting.
To stop in this mode … Do this … To start up or resume again Hibernation Depending on your settings in Windows, you can place the computer in Hibernation mode: l by pressing the power button l by closing the display cover. Press the power button. If you choose to stop in Standby or Hibernation mode, you can return to where you left off the next time you start up the computer. (See “Power Management” in Chapter 3 for more information.
Using the Keyboard Your keyboard has all the standard functions of a full-sized computer keyboard plus a Fn. key added for specific functions. The standard functions of the keyboard can be further divided into four major categories: Typewriter keys Cursor-control keys Numeric keys Function keys Typewriter Keys Typewriter keys are similar to the keys on a typewriter. Several keys are added such as the Ctrl, Alt, Esc, and lock keys for special purposes.
Numeric Keypad A 15-key numeric keypad is embedded in the typewriter keys as shown next: Numeric keys facilitate entering of numbers and calculations. When Num Lk is on, the numeric keys are activated; meaning you can use these keys to enter numerals with “Fn” key. NOTE: Some software may not be able to use the numeric keypad on the computer. If so, use the numeric keypad on an external keyboard instead. l Euro Symbol If your Windows supports the Euro dollar sign the sign on the keyboard.
Function Keys On the top row of the keys are the function keys: F1 to F12. Function keys are multi-purpose keys that perform functions defined by individual programs. Hot key functions are assigned to F1, F3 , F4, F5, F6, F8, F9, and F10 by your computer. (See “Hot Keys” section in this chapter for information.) Fn. Key The Fn. key, at the lower left corner of the keyboard, is used with another key to perform the alternative function of a key. The letter “Fn.
Key Description Fn+F9 Switches the display output to one of the following three when an external CRT monitor is connected through the docking station. LCD CRT monitor Display on both NOTE: If the display mode is set to 256 colors or lower, or in DOS mode, there will be only two modes for selecting: CRT only and Display on both. Fn+F10 Serves as the sleep button that you can define with Windows’ Power Management. (See “Power Management” in chapter 3.
Using the Touchpad CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may damage the touchpad surface. NOTE: For optimal performance of the touchpad, keep your fingers and the pads clean and dry. When tapping on the pad, tap lightly. Do not use excessive force. The touchpad is a pointing device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons.
Term Drag and drop Action Press and hold the left button, then move your fingers until you reach your destination (drag). Finally, release the button (drop) when you finish dragging your selection to the destination. The object will drop into the new location. -orGently tap twice on the pad, and on the second tap, keep your finger in contact with the pad. Then, move your finger across the pad to drag the selected object to your destination.
Using the Touchscreen (Optional) CAUTION: Do not use a sharp object such as a ballpoint pen or pencil on the touchscreen. Doing so may damage the touchscreen surface. Use the included touchscreen pen instead, which can be stretched for better grip and handling. The touchscreen is a touch-sensitive device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons.
Term Scroll Action To scroll is to move up and down or left and right in the working area on the screen. To move vertically, place your finger or pen on the right edge of the touchscreen and slide your finger or pen up and down along the edge. To move horizontally, place your finger or pen on the bottom edge of the touchscreen and slide your finger or pen left and right. This function works only after you install the touchscreen driver supplied with the computer and it may not work for all applications.
Using the Floppy Disk Drive (optional) Your computer may come with the optional floppy disk drive as drive A through the optional docking station. A floppy disk drive allows you to install new programs into your computer, or to store information on a removable floppy disk so you can transfer information from one computer to another. The floppy disk drive is a high-density 3.5-inch one, which can read and write to either double-density (2DD) 720-KB floppy disks or high-density (2HD) 1.44-MB floppy disks.
Inserting and Ejecting Floppy Disks To insert a floppy disk, hold it with the arrow facing up and towards the drive. Slide the disk into the drive until it clicks into place. To eject a floppy disk, first ensure that the floppy disk drive in-use indicator is off, and then press the eject button on the drive. When the floppy disk pops out of the drive, remove the floppy disk and store it properly. CAUTION: l Never turn off or reset the computer while the floppy disk drive in-use indicator is on.
Using the Hard Disk Drive Your computer comes with a hard disk drive as drive C. A hard disk drive is a storage device with non-removable, rotating, magnetic storage platters inside it. It is where your operating system and application software programs are stored. Your hard disk drive is a 2.5-inch IDE (Integrated Drive Electronics) hard disk drive.
Using the CD/DVD/COMBO Drive (optional) Your computer may come with an optional CD-ROM drive, COMBO drives, or DVD-ROM drives through the optional docking station. This drive is usually configured as drive D. The drive uses removable 5.25-inch silver CD-ROM discs, which look like standard music CDs. It is an ideal medium to use for distributing multimedia because of the huge amount of data that a disc can store. A CD-ROM drive can read CD-ROMs, audio CDs, CD-R, and COMBO disk.
Inserting and removing a CD Follow this procedure to insert or remove a CD. 1. Turn on the computer. 2. Press the eject button and the CD tray will slide out partially. Gently pull it until fully extended. 3. To insert a CD, put down the CD in the tray with its label facing up. Slightly press the center of the CD until it clicks into place. To remove a CD, hold the CD by its outer edge and lift it up from the tray. 4. Gently push the tray back into the drive.
Using the Video Features The video subsystem of your computer features: l 12.1-inch TFT (Thin-Film Transistor) color LCD display with 1024x768 XGA (Extended Video Graphics Array) resolution. l Sunlight Readable Panel , Hi-Contrast solution LCD (Optional). l Simultaneous display on LCD and external monitor (connect through the docking station), which is useful when you have a presentation as you can control the screen from your computer and face the audience at the same time.
Display Mode Resolution 640x480 720x480 800x600 848x480 2-18 LCD Only CRT Only Simultaneous Display Colors 8-bit √ √ √ 16-bit √ √ √ 24-bit √ √ √ 32-bit √ √ √ 8-bit √ √ √ 16-bit √ √ √ 24-bit √ √ √ 32-bit √ √ √ 8-bit √ √ √ 16-bit √ √ √ 24-bit √ √ √ 32-bit √ √ √ 8-bit √ √ √ 16-bit √ √ √ 24-bit √ √ √ 32-bit √ √ √ Operating Your Computer
LCD Only CRT Only Simultaneous Display 8-bit √ √ √ 16-bit √ √ √ 24-bit √ √ √ 32-bit √ √ √ Display Mode 1024x768 1152x864 1280x1024 1600x1200 8-bit √ 16-bit √ 24-bit √ 32-bit √ 8-bit √ 16-bit √ 24-bit √ 8-bit √ 16-bit √ TABLE NOTE: 8-bit = 256 colors; 16-bit = High Color or 65,536 (64 K) colors; 24 and 32-bit = True Color 16,770,000 (16 M) colors.
Using the Audio Features NOTE: To take advantage of the enhanced audio capabilities, the audio driver supplied with your computer must be installed. l If you experience interference while recording, try lowering the microphone recording volume.
Using the Communication Features Using the Modem NOTE: To take advantage of the modem feature, the modem driver supplied with your computer must be installed. The internal 56 K fax/data modem allows you to use the telephone line to communicate with others by fax, email, or connect to an online service or bulletin board. To connect the telephone line to the modem, connect the end nearest the core on the modem cable to the computer’s RJ-11 connector and the other end to the telephone line.
Using the Wireless LAN Depending on your model, an internal Mini PCI wireless LAN (WLAN) card may have been pre-installed by your computer manufacturer at the factory. This card allows you to access corporate networks or the Internet in a wireless environment. The WLAN features include: IEEE 802.11b standard compliance 2.
CHAPTER 3 Managing Power Your computer operates either on external AC power, car adapter, or internal battery power. This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way.
AC and Car Adapter CAUTION: z The AC and car adapter is designed for use with your computer only. Connecting the AC adapter to another device can damage the adapter. z The AC power cord supplied with your computer is for use in the country where you purchased your computer. If you plan to go overseas with the computer, consult your dealer for the appropriate power cord. z When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer.
Battery Pack The battery pack is the internal power source for the computer. It is rechargeable using the AC or car adapter. The operating time of a fully charged battery pack depends on how you are using the computer. When your applications often access peripherals, you will experience a shorter operating time. NOTE: Care and maintenance information for the battery is provided in Chapter 8. In addition to this chapter, be sure to read the “Battery Pack Guidelines” section in Chapter 8 as well.
Initializing the Battery Pack You need to initialize a new battery pack before using it for the first time or when the actual operating time of a battery pack is much less than expected. Initializing is the process of fully charging, discharging, and then charging. It can take several hours. 1. Make sure the computer power is turned off. Connect the AC adapter to fully charge the battery pack. 2. After the battery pack is fully charged, turn on the computer. 3.
If you often rely on battery power for a long period of time while traveling, you may consider the purchase of an additional battery pack from your dealer and keep it with you in a fully charged state as a backup. To replace the battery pack, follow these steps: 1. Make sure the computer is not turned on or connected to AC power. 2. Carefully place the computer upside down. 3. Slides the battery cover latch inward and remove the battery compartment cover. Battery Cover Latch 4. Pull the battery pack.
5. Pull on the protruding strip to slide the battery pack to the left and lift the battery pack out of its compartment. Pull Battery Pack 6. Insert the new battery pack into the compartment and slide the battery pack to the right to allow the proper connection of connectors. 7. In order to fixed battery back, we put the battery block on the rear of the battery. 8.Replace the battery compartment cover and slide the battery cover latch outward to secure it.
Battery Low Signals and Actions Battery Low occurs when the battery has approximately 10% of its charge remaining. The computer in the Battery State Indicator LED blink to alert you to take actions. NOTE: You can set up your threshold and signals of Battery Low under Windows. Immediately save your data upon Battery Low. The remaining operating time depends on how you are using the computer.
Power Management Your computer supports APM (Advanced Power Management) and ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving. With an ACPI-compliant operating system such as Windows 98 and Windows 2000, power supply to different computer components is controlled on an as-needed basis. This allows maximum power conservation and performance at the same time.
Manual Power Management You can manually initiate Suspend-to-disk mode at any time in one of two ways: l Use the O/S that supports the Suspend function. l Press down the power button and release it in less than 4 seconds with the system on. Repeat the action to wake up the system under Suspend mode. Suspend-to-disk is a very useful feature. People frequently open many applications when they use computers.
Power-Saving Tips In addition to your computer’s automatic power management, you can do your part to maximize the battery’s operating time by following these suggestions. l Do not disable Power Management. l Decrease the LCD brightness to the lowest comfortable level. l Disable the parallel and serial ports if no devices are connected to these ports. (See “Advanced Menu” in Chapter 5.) l If you work with an application that uses the serial port or a PC Card, exit the application when you finish using it.
CHAPTER 4 Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter.
Connecting an External Monitor (Optional) If you want the benefits of a larger display screen with higher resolution, you can connect an external CRT monitor to your computer through the optional docking station. Follow this procedure to connect an external monitor: 1. Make sure the computer is not turned on. 2. Plug the monitor’s D-type signal connector to the docking station’s VGA port. 3.
Connecting a Parallel Device (optional) The optional docking station has a p arallel port for connecting a parallel device such as printer. The port supports ECP (Extended Capabilities Port) and EPP (Enhanced Parallel Port) modes that turn the standard parallel port into a high-speed bi-directional peripheral port. Follow this procedure to connect a parallel device: 1. Make sure that the “LPT Port” item is set properly in the BIOS Setup program. (See “Advanced Menu” in Chapter 5 for information.) 2.
Connecting a Serial Device Your computer has a serial port for connecting a serial device such as a serial mouse or modem. Follow this procedure to connect a serial device: 1. Make sure the “COM1 Port” item is set properly in the SCU program. (See “Advanced Menu” in Chapter 5 for information.) 2. Make sure the computer is not turned on. 3. Plug the device cable to the serial port on the computer.
Connecting a USB Device (USB 2.0) Your computer has one USB port on the right side for connecting USB 2.0 devices such as digital camera, scanner, printer, modem, or mouse and two USB ports on the left side of the optional docking station. USB is specified to be an industry standard extension to the PC architecture. It supports “Plug-and-Play” technology so you can install and remove USB devices without turning off the computer.
Using PC Cards Your computer has one PC Card slot to accommodate one type II card. ZV Port and CardBus Support Your computer’s PC Card slot supports CardBus and ZV (Zoomed-Video) Port specifications. CardBus is the 32-bit version of PC Card technology. It allows speeds of up to 133 Mbps at 33 MHz. Typical applications are SCSI host bus, graphic video, and high-speed network cards. Inserting and removing a PC Card NOTES: l Some PC Cards require additional system resources.
To remove a PC Card: 1. Your operating system may require you to stop the PC Card before you actually remove it. (In Windows, double-click the PC Card icon in Control Panel to stop the card.) 2. Push the eject button and the card will slide out slightly. 3. Pull the card out of the slot. System Memory Upgrade You can upgrade your computer by changing system memory to a maximum of 1GB on the DDR SDRAM slot. However, to avoid damage during the installation procedure, please ask your dealer for help.
4-8 Expanding Your Computer
CHAPTER 5 Setup Configuration Utility (SCU) SCU is a program for configuring the BIOS (Basic input/output System) settings of the computer. BIOS are a layer of software, called firmware that translates instructions from other layers of software into instructions that the computer hardware can understand. The BIOS settings are needed by your computer to identify the types of installed devices and establish special features. This chapter tells you how to use the SCU program.
When and How to Use the SCU Program When to Use You need to run the SCU program when: l You see an error message on the screen requesting you to run Setup. l You want to restore the factory default settings. l You want to modify some specific settings according to the hardware. l You want to modify some specific settings to optimize system performance. Starting SCU NOTES: l The Setup screens shown in this chapter are for your reference only. The actual items or settings on your computer may differ.
The menu can be divided into four areas: l On the top line is the menu bar containing the titles of the available menus. Each menu title brings a specific menu. l The center left column of the menu contains items that you can set for the selected menu title. l The right column of the menu provides help information of the selected item. l The bottom lines give keyboard instructions for moving around and making selections.
Moving Around and Making Selections A brief description of keyboard usage is listed next: Key Function ←, → Selects a menu title. ↑, ↓ Selects an item or option. Enter Opens or closes the options window when an item is selected. Space bar, Cycles through the pre-defined value for the selected item. – Pressing the space bar brings up the next value; pressing the minus (–) key does the contrary. Esc 1) Exits the SCU program. 2) Returns to the previous menu if in a submenu.
Main Menu The Main menu contains the basic configuration settings of the system. Date and Time Sets the system date and time.
Internal and Numlock sets if you can enter a number when Num Lock is turn off. When this item is enabled, you can press and hold FN, and then press a letter key to enter a number even if Num Lock is turned off. When this is disabled, you cannot enter a number with the above method. A check mark (ü) indicates enabled while undline (_) indicates disabled. USB Emulation enables or disables the system’s support for the USB port in DOS mode.
Advanced Menu The Advanced menu contains the input/output configuration settings of the system. Geyserville Support Enables or disables the Geyserville feature of the CPU. The Geyserville feature helps conserve battery life by decreasing the CPU’s running speed under certain conditions while still maintaining a high performance. If this item is enabled, the CPU will automatically change its speed whenever necessary based on the “Power Scheme” setting in Windows’s Control Panel.
Shared Video Memory sets the shared memory size of the video controller. The options are 4M, 8M, 16M and 32M.
HDD Hearter Security Menu The Security menu contains the security setting that safeguards your system against unauthorized use.
Set Password allows you to set the password for your system. When typing password, first make usre that Num Lock is off, then type your password in the entry fields and press Enter. Confirm your password by typing it again and pressing Enter. If the Enable Password to Power-on sub-item is enabled, the set password is always required to boot the computer. Hard Disk Boot Sector sets if a warning message will appear when the hard disk boot sector (partition table) has been changed.
Boot Menu The Boot men sets the sequence of the devices to be searched for the operating system.
Boot Sequence sets the first, second, third, and fourth booting devices. The system will try to boot from the first device but if it is not available, will try the next boot device. If you set the first boot device to LAN Boot, the system will boot from the LAN server first. The options are Hard Disk Drive, CD-ROM Drive, Floppy Disk Drive, and LAN Boot. The default setting is Floppy Disk Drive, Hard Disk Drive, CDROM Drive, then LAN Boot.
Exit Menu The Exit menu displays ways of exiting SCU. After finished with your setting, you must save and exit so that the new setting can take effect. Save Change and Exit saves the changes you have made and exits SCU. Discard Changes and Exit exits SCU without saving the changes you have made. Get Default Values loads factory default values for all the items. Load Previous Values loads CMOS values before running SCU.
5-14 Setup Configuration Utility
CHAPTER 6 Installing Software Drivers To take full advantage of the unique features of your computer, some operating systems require custom software, known as drivers, to be installed. If you purchased the computer with Windows pre-installed; your dealer may have already installed the drivers. If not, you need to install the drivers using the CD supplied with your computer. This chapter describes how to install the drivers.
How to Use the CD NOTES: • The drivers may have been updated after this manual was published. For driver’s upgrade, please contact your dealer. • You can always find README or document files on the CD. These files contain the latest information from the software supplier. Please read the files together with this chapter. • This driver CD supports Windows 2000 and Windows XP only. • The available items may differ according to your computer model and Operating System.
Install Device Driver for Windows 2000/Windows XP To install the necessary driver, just click on the particular option and follow the onscreen instructions to continue and complete installation. Device Driver Press the “Device driver” button, the system will auto install include VGA, Audio, Modem, LAN , Wireless LAN, USB 2.0, DirectX 8.1, Chipset driver.
VGA Allows you to select high-resolution displays with richer colors. It can drive CD displays as well as CRT displays. Audio Allows you to take full advantage of the audio subsystem. Modem The modem driver allows you to transmit information over a standard telephone line through RJ-11 port. Speedstep Press the Speedstep button, the system will auto install for Window 2000. LAN/Wireless LAN Allows you to use the network function of the computer. USB 2.0 Allows your system to connect to USB 2.0 devices.
Install Touch Screen Driver for Windows 2000 1. Insert the driver CD into the drive. 2. Click on “TOUCH SCREEN” then “WIN2000”, and follow the onscreen instructions to continue. 3. When finished installing, select “Yes” to reboot your system. The driver should now be loaded. 4. After the system has finished rebooting, click on the “PenMount Monitor” icon located on the taskbar to bring up the “PenMount Control Panel.” 5. Select the “ Standard Calibrate” folder and click on “OK” button. 6.
Installing Drivers for Windows XP To set up the necessary drivers for Windows XP, click on “TOUCH SCREEN ” on the initial screen.
Install Touch Screen Driver for Windows XP Hardware Install: (1) Insert the driver CD to the CD drive, to bring up the following screen. Select “WINXP”.
(2) When the TSRC-XP.htm file appear, then select ”START” -> “Control Panel” button.
(4) When the “Control Panel “ screen appear, then click on “ performance and Maintenance” button.
(5) When the “Performance and Maintenance” screen appear, and then click on “System” button.
(5) When the “System Properties” screen appear, and then click on “Hardware” and “Device Manager “ button.
(6) When the “Device Manager” screen appear, then click on “ ?Unknown device” and then click on the “Properties” icon.
(8) When the “Unknown Device Properties” screen appear, and then click on “ Reinstall Driver” button.
(9) When the “Hardware Update Wizard” appears, click on “ Install the software automatically [Recommand], then click on ”Next”. (10) When the “Hardware Installation” screen appears, click on ”Continue Anyway”.
(11) When the “Hardware Update Wizard”screen appears, click on ”Finish” button.
(12) When the “PenMount DMC9000 and DMC9100 Properties”screen appears, click on ”Close” button to exit the driver installation..
Touchscreen Utility To install the touchscreen utility, perform the following: (1) Insert the driver CD to the CD drive, to bring up the following screen. (2) Click on “Start” then “Run”.
(3) Enter the following directory on the driver CD: \TOUCHSCREEN\Setup.exe, then click on “OK”. (4) Select “Yes” to the question if this is the first time to run this setup. (5) When the “InstallShield Wizard” appears, click on “Next” to continue. (6) Select “ I accept the terms in the license agreement,” then click on “Next”. (7) When the “Ready to Install the Program” screen appears, clcik on “Install” to continue. (8) Reboot the system.
(11) If you need 4,9,16,25 dot of the calibrate, we suggest select “ Advanced Calibration” button to calibrate. (13) Click on the four sides red points and plus sign on the screen to calibrate your “PENMOUNT” pen to start using your ML 850’s Touchscreen.
6-20 Installing Software Drivers
CHAPTER 7 Caring for the Computer Taking good care of your computer will ensure a trouble-free operation and reduce the risk of damage to your computer.
Protecting the Computer To safeguard the integrity of your computer data as well as the computer itself, you can protect the computer in several ways as described in this section. Using the Password The power-on password protects your computer against unauthorized use. If the password is set, the prompt requesting for the password appears on the screen whenever the computer is turned on. The password is set via the SCU program. See “Security Menu” in Chapter 5 for instructions.
Taking Care of the Computer Location Guidelines l Use the computer where the temperature is between 0 °C to 55 °C . l Avoid placing the computer in a location subject to high humidity, extreme temperatures, mechanical vibration, direct sunlight, or heavy dust. l Do not cover or block any ventilation openings on the computer. For example, do not place the computer on a bed, sofa, rug, or other similar surface. Otherwise, overheating may occur that results in damage to the computer.
Cleaning Guidelines l Never clean the computer with its power on. l Use a soft cloth moistened with water or a non-alkaline detergent to wipe the exterior of the computer. l Gently wipe the display with a soft, lint-free cloth. Do not use alcohol or detergent on the display. l Dust or grease on the touchpad/touchscreen can affect its sensitivity. Clean the pad/screen by using adhesive tape to remove the dust and grease on its surface.
When Traveling l Before traveling with your computer, make a backup of your hard disk data into floppy disks or other storage devices. As an added precaution, bring along an extra copy of your important data. l Make sure the battery pack is fully charged. l Make sure the computer is turned off and the top cover is securely closed. l Do not leave objects that will press onto the display. l Disconnect the AC adapter from the computer and take it with you.
7-6 Caring for the Computer
CHAPTER 8 Troubleshooting Hardware, software, or a combination of both can cause computer problems. When you encounter any problem, it might be a typical problem that can easily be solved. This chapter tells you what actions to take when solving common computer problems.
Preliminary Checklist Here are helpful hints to follow before you take further actions when you encounter any problem: l Try to isolate which part of the computer is causing the problem. l Make sure that you turn on all peripheral devices before turning on the computer. l If an external device has a problem, make sure that the cable connections are correct and secure. l Make sure that the configuration information is properly set in the SCU program.
Solving Common Problems For easy reference, the problems are divided into these categories. Problem Type Go to Battery problems P. 8-4 CD/DVD/COMBO drive problems (on optional docking station) P. 8-5 Display problems P. 8-5 Floppy disk drive problems (on optional docking station) P. 8-7 Hardware device problems P. 8-8 Hard disk drive problems P. 8-8 Keyboard, mouse, and touchpad problems P. 8-9 LAN problems P. 8-10 Wireless LAN problems P. 8-10 Modem problems P.
Battery Problems The battery does not charge (Battery Charge LED indicator does not light orange). l Make sure that the AC adapter is properly connected. l Make sure that the battery is not too hot – gets above 55oC or too cold – below 0oC. Allow time for the battery pack to return to room temperature. l Make sure that the battery pack is installed correctly. l Make sure that the battery terminals are clean. The operating time of a fully charged battery becomes shorter.
CD/DVD/COMBO Drive Problems (on optional docking station) The CD/DVD/COMBO drive cannot read a CD. l Make sure that the CD is correctly seated in the tray, with the label facing up. l Make sure that the CD is not dirty. Clean the CD with a CD cleaning kit, available in most computer stores. l Make sure that the CD/DVD/COMBO drive driver is installed correctly. l Make sure that the computer supports the CD or files. You cannot eject a CD. l The CD is not properly seated in the drive.
l The brightness level might be too low. Increase brightness by pressing Fn+F6. l The display output might be set to an external monitor. To switch the display back to the LCD, press Fn+F9. l Reset the computer by pressing the Ctrl+Alt+Del keys if you are using an external keyboard. l Try turning the computer off; wait a few seconds, then turn it backs on. The characters on the screen are dim. l Adjust the brightness. Bad dots appear on the display at all times.
The external monitor displays nothing. l Make sure that the monitor is turned on. l Make sure that the monitor’s signal cable is properly connected. l Check if the Setup item Display Mode on the Main menu of the SCU program is configured correctly. l Switch the display to the monitor by pressing Fn+F9 or through the Windows’ Display properties. Simultaneous display does not work. l Make sure that you turn on the external monitor before turning on the computer.
The disk drive cannot read a floppy disk. l Make sure that the floppy disk is formatted. l Make sure that you are reading the correct drive. Hardware Device Problems The computer does not recognize a newly installed device. l The device may not be correctly configured in the SCU program. Run the SCU program to identify the new type. l Make sure if any device driver needs to be installed. (Refer to the documentation that came with the device.) l Make sure if the device needs any jumper or switch settings.
The hard disk drive in-use indicator glows without blinking. l The data files stored on the hard disk drive may be fragmented. Use a tool such as Window’s Disk Defragmenter to defragment the files. Keyboard, Mouse and Touchpad Problems The keyboard does not respond. l Try connecting an external keyboard. If it works, contact the authorized dealer, as the internal keyboard cable might be loose. The numeric keypad is disabled. l Make sure that Num. Lk is switched on. (Check if the Num.
LAN Problems I cannot access the network. l Make sure that the LAN driver is correctly installed. l Make sure that the LAN cable is properly connected to the RJ-45 connector and the network hub. l Make sure that the network configuration is appropriate. l Make sure that the user name or password is correct. Wireless LAN Problems I cannot use the WLAN feature. Make sure that the Mini PCI WLAN card is correctly installed. Make sure that the necessary driver(s) is correctly installed.
PC Card Problems The PC Card does not work. l Make sure that the PC Card is correctly seated. l If the card requires an IRQ (interrupt request), make sure that there is one available. l The PC Card may be attempting to use a COM port in a manner that conflicts with the COM port being used by another device. Try running the SCU program to change the COM port setting. If your PC Card uses COM1, set COM1 as Disabled. If your PC Card uses COM3, set COM3 as Disabled.
l Make sure that the Standby or Suspend time-out is enabled. The computer does not enter Standby or Suspend mode immediately. l If the computer is performing an operation, it normally waits for the operation to finish. The computer does not resume from Standby or Suspend mode. The computer automatically enters Standby or Suspend mode when the battery pack is empty. Does any one of the following: − Connect the AC or car adapter to the computer. − Replace the empty battery pack with a fully charged one.
Software Problems An application program does not work correctly. l Make sure that the software is correctly installed. l If an error message appears on the screen, consult the software program’s documentation for further information. l If you are sure the operation has stopped reset the computer. (See “Resetting the Computer” in this chapter.) Sound Problems No sound is produced. l Make sure that the volume control is not set too low. l Make sure that the audio driver is correctly installed.
Startup Problems When you turn on the computer, it does not respond and the Power Indicator does not light green. l If you are using an external AC power, make sure that the AC adapter is correctly and securely connected. If so, make sure that the electrical outlet works properly. l If you are using the battery power, make sure that the battery is not discharged. When you turn on the computer, it stops after POST. l Restart your computer.
Other Problems The date/time is incorrect. l Correct the date and time via the operating system or SCU program. l After you have performed everything as described above and still have the incorrect date and time every time you turn on the computer, the RTC (real-time Clock) battery is at the end of its life. Call an authorized dealer to replace the RTC battery. Resetting the Computer You may have to reset (reboot) your computer on some occasions when an error occurs and the program you are using hangs up.
8-16 Troubleshooting
APPENDIX R Specifications NOTE: Specifications are subject to change without any prior notices. Parts CPU Cache Memory ROM BIOS RAM System Display Video Panel Video controller Video port Keyboard Pointing device Storage Floppy disk drive device Hard disk drive CD/DVD/COMBO drive Audio Audio controller& Audio port PC Card Specifications Specifications Intel Pentium M Processor LV1.
Specifications Parts I/O ports On computer Serial Port × 1 VGA Port x 1 USB 2.0 port x 2 DC input x1 Docking Port x1 RJ-11x1 for 56Kbps Software Modem port RJ-45 100 Base-T LAN port Microphone-in & Earphone out ports Docking station (option) Serial Port × 1 (pure serial singal) Serial Port x 1 (USB transfer to serial signal) Parallel Port x 1 VGA port x 1 USB 2.
