ML900 Operation Manual Part Number: 7990 0114 3001 R03 (April 2004)
TRADEMARKS All brand and product names are trademarks or registered trademarks of their respective companies. NOTE Information in this manual is subject to change without notice.
Regulations Information Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
COMPUTER SOFTWARE COPYRIGHTS The Motorola products described in this instruction manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including the exclusive right to copy or reproduce in any form the copyrighted computer program.
Motorola, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it with the same or equivalent Product (using new or reconditioned Product), or refund the purchase price of the product during the warranty period provided purchaser notifies Motorola according to the terms of this warranty. Repaired or replaced Product is warranted for the balance of the original applicable warranty period. All replaced parts of the Product shall become the property of Motorola.
Motorola, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it with the same or equivalent Product (using new or reconditioned Product), or refund the purchase price of the product during the warranty period provided purchaser notifies Motorola according to the terms of this warranty. Repaired or replaced Product is warranted for the balance of the original applicable warranty period. All replaced parts of the Product shall become the property of Motorola.
MOTOROLA DISCLAIMS ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
I) A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with Motorola’s published specifications or with the FCC type acceptance labeling in effect for the Product at the time the Product was initially distributed from Motorola. J) Scratches or other cosmetic damage to Product surfaces that do not affect the operation of the Product.
C) Should the Product or its parts become, or in Motorola’s opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit Motorola, at its option and expense, either to procure for such purchaser the right to continue using the product or its parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or its parts as depredated and accept its return.
About the Battery Caution Texts Concerning Lithium Batteries DANISH ADVARSEL! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren. NORWEGIAN ADVARSEL: Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruksjoner.
FRENCH ATTENTION: II y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d’un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. Attention (for USA Users) The product that you have purchased contains a rechargeable battery. The battery is recyclable.
Table of Contents Preface ........................................................................................ v Chapter 1 Getting Started .....................................................1-1 Getting the Computer Running................................................1-2 Unpacking ..........................................................................1-2 Connecting to AC Power ...................................................1-3 Opening the Cover ................................................
Numeric Keypad ................................................................2-5 Euro Symbol ......................................................................2-6 Windows Keys ...................................................................2-6 Function Keys ....................................................................2-6 Fn Key................................................................................2-7 Hot Keys ..........................................................................
Chapter 4 Expanding Your Computer..................................4-1 Connecting an External Monitor .............................................4-2 Connecting a USB Device .......................................................4-3 Connecting a Serial Device- ....................................................4-4 Connecting an IR Device.........................................................4-5 Connecting an IR or Bluetooth-compliant Device ..................4-7 Connecting an IEEE 1394 Device ..........
Cleaning Guidelines ...........................................................7-4 Battery Pack Guidelines .....................................................7-4 When Traveling .......................................................................7-5 Chapter 8 Troubleshooting................................................... 8-1 Preliminary Checklist ..............................................................8-2 Solving Common Problems .....................................................
Preface This manual contains information that will help you operate the computer. It is divided into 8 chapters and an appendix. Chapter 1, Getting Started, takes you through the process of setting up the computer and identifying its external components. Chapter 2, Operating Your Computer, tells you how to use the computer’s components and features. Chapter 3, Managing Power, provides information on power. Chapter 4, Expanding Your Computer, provides information on installing and using peripheral devices.
Appendix B, Fingerprint Recognition System, provides information on using the system’s fingerprint recognition system. Notational Conventions Throughout this manual, the following conventions are used to distinguish elements of text. NOTE: identifies additional information that requires special attention. CAUTION: identifies important information which, if not followed, may result in loss of data or damage to the computer. Keyboard keys are shown in a bold typeset. For example: Press Enter to complete.
CHAPTER 1 Getting Started Congratulations on purchasing this computer. This high performance notebook computer is especially designed for the practical applications of warehouses, automobiles, vehicles, public security, repairing, assisting the handicapped, and other demanding situations where conventional notebook computers just cannot measure up. This chapter first tells you step by step how to get the computer up and running.
Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation. Unpacking After unpacking the shipping carton, you should find these standard items: Notebook computer Accessories: − AC adapter (100~240 VAC, 50/60 Hz) − AC power cord (US, CE, UK, SA) − Driver CD − Fingerprint recognition scanner in main system (includes software) − This Operation Manual Inspect all the items. If any item is damaged or missing, notify your dealer immediately.
NOTE: Power Supply Cord: (optional) Detachable, minimum 1.5 m long. Listed, rated minimum 125 V, 7 A, having a 2/18 AWG, type SVT flexible cord. One end terminates with a parallel blade, molded-on, attachments plug with a 7 A, 125 V (NEMA 1-15P) configuration; other end terminates with a molded-on appliance coupler. Alternative: (optional) Detachable, maximum 4.5 m (14.76 ft) long. Listed, rated minimum 250 V, 6 A, having a 3/18 AWG, type SVT flexible cord.
CAUTION: When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer. A reverse procedure may damage the AC adapter or the computer. When unplugging the connector, always hold the plug head. Never pull on the cord. NOTE: When the AC adapter is connected, it also charges the battery pack. For information on using battery power, see Chapter 3. Opening the Cover CAUTION: Be gentle when opening and closing the cover.
3. Each time the computer is turned on, it performs a Power-On Self Test (POST), and the operating system such as Windows should start. Turning Off To turn off the computer power, use the “Shut Down” command of your operating system. NOTE: There are other ways you can stop the computer so that you will be back to where you left off when you next turn on the computer. (See “Stopping the Computer” in Chapter 2 for information.
Taking a Look at the Computer This section identifies the external components of the computer and briefly describes the function of each component. NOTE: Depending on the model you purchased, the appearance of your computer may not exactly be the same as those shown in this manual. Right-Side Components Ref Component Description See Also n IEEE 1394 Port Connects a 1394 device, such as a scanner, printer, digital camera, joystick, and more.
Left-Side Components Ref Component Description See Also n IR Port Connects an IrDA-compliant device for wireless data transfer. P. 4-5 o Bluetooth Port Connects a bluetooth-capable device for wireless data transfer. P. 4-5 p Microphone Connector Connects an external microphone. q Keyboard BIOS Use this to turn off the system when resetting the system using Ctrl+Alt+Del does not work. Reset Switch P.
Rear Components Ref Component Description See Also n DVI-I Port Connects an external monitor. P. 4-2 o Serial Port Connects a serial device, such as an external modem. P. 4-4 p Docking Port For connecting to a Port Replicator / car mount. q Rear Cover Latch Locks the rear cover. r USB Ports Each of the two ports connects a USB device, such as a floppy disk drive, printer, digital camera, joystick, and more. P. 4-3 s AV Input Port Connects to a video recording device. P.
Front Components Ref Component Description See Also n Wireless Modem Antenna Serves as the antenna for the wireless modem (RDLAP, GPRS, iDEN, and CDMA). P. 2-27 o Stereo Speaker Set Sends out sound and voice from the computer. P. 2-22 p Handle Allows you to carry your computer for an easy grip. q Wireless LAN Antenna Serves as the antenna for the WLAN. It is built-in the handle. P. 2-25 r GPS Antenna (option) Serves as the antenna for the Global Positioning System (GPS).
Bottom-Side Components Ref Component n X-bay Module Antenna Connector Serves as the interface between the system and antenna of the X-bay module. o CD Drive Lock/Unlock Switch Allows you to lock the CD drive in place (can also contain the floppy disk drive or secondary battery). P. 2-13, 2-17 p CD/DVD Drive Eject Latch Allows you to remove the CD drive (can also contain the CD R-W or DVD drive). P. 2-13 q GPS Connector Serves as the interface between the system and external GPS antenna.
Ref Component Description See Also t Primary Battery Pack Supplies power to your computer when external power is not connected. P. 3-3 u Secures the primary battery compartment cover Primary Battery Release in place. Latch P. 3-5 v X-Bay Interface (top) Mini PCI Slot (bottom) Connects additional wireless modem (GPRS/ GSM or iDEN). Inside is the Mini PCI slot for using an optional Mini PCI card.
Top-open Components Ref Component Description See Also n Fingerprint Scanner Contains the fingerprint sensor. P. B-1 o p Keyboard Serves as the data input device of the computer. P. 2-4 Power Button Turns the computer power ON and OFF. P.
q Device Indicators Show the current status of the computer’s devices. Power on / Standby mode indicator Hard disk drive in-use indicator P. 1-3 P. 2-15 Num Lock indicator P. 2-6 Caps Lock indicator P. 2-4 Scroll Lock indicator P. 2-4 r LCD Screen Displays the output of the computer. P. 2-20 s Light Sensor Automatic light sensor for dimming the display’s backlight. P. 2-20 t Touchpad Serves as the pointing device of the computer.
Where to Go from Here As your computer is ready for operation, you may want to do any of the following now: For this purpose… To know more about the computer… Do this… Go on to the next chapter. To install the operating system if your See the operating system manual. dealer has not already done so… To know more about the operating system… Read the operating system manual. To install the drivers if your dealer has See Chapter 6.
CHAPTER 2 Operating Your Computer This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the operating basics. If you are already a computer user but are new to notebook computers, you may choose to read only the parts containing information unique to your computer.
Starting and Stopping the Computer There are a number of ways to start and stop the computer. Starting the Computer You always start the computer using the power button. A computer starts up with an operating system (OS) existing on the storage device such as the hard disk; or from a floppy disk or CD if you have the respective modules installed. The computer will automatically load the OS after you turn it on. This process is called booting.
To stop in this mode… Do this… Hibernation Depending on your settings in Windows, you can place the computer in Hibernation mode by: • Closing the display cover. • Pressing the power button To start up or resume again Press the power button. If you choose to stop in Standby or Hibernation mode, you can return to where you left off the next time you start up the computer. (See “Power Management” in Chapter 3 for more information.
Using the Keyboard Your keyboard has all the standard functions of a full-sized computer keyboard plus a Fn key added for specific functions. The standard functions of the keyboard can be further divided into four major categories: Typewriter keys Cursor-control keys Numeric keys Function keys Typewriter Keys Typewriter keys are similar to the keys on a typewriter. Several keys are added such as the Ctrl, Alt, Esc, and lock keys for special purposes.
Cursor-Control Keys NOTE: The word “cursor” refers to the indicator on the screen that lets you know exactly where on your screen anything you type will appear. It can take the form of a vertical or horizontal line, a block, or one of many other shapes.
Numeric keys facilitate entering of numbers and calculations. When Num Lock is on, the numeric keys are activated; meaning you can use these keys to enter numerals. NOTES: When the numeric keypad is activated and you need to type the English letter in the keypad area, you can turn Num Lock off or you can press Fn and then the letter without turning Num Lock off. Some software may not be able to use the numeric keypad on the computer. If so, use the numeric keypad on an external keyboard instead.
Fn Key The Fn key, at the lower left corner of the keyboard, is used with another key to perform the alternative function of a key. The letter “Fn” and the alternative functions are identified by the color of blue on the keytop. To perform a desired function, first press and hold Fn, then press the other key. Hot Keys Hot keys refer to a combination of keys that can be pressed any time to activate special functions of the computer. Most hot keys operate in a cyclic way.
Key Description Switches the display output to one of the following when an external device is connected. Upon booting the system with CRT: LCD CRT LCD & CRT NOTES: If the display mode is set to 256 colors or lower, or in DOS mode, there will be only two modes for selecting: CRT only and LCD & CRT. This function only applies to Plug & Play CRT monitors. Serves as the sleep button that you can define with Windows’ Power Management. (See the “Power Management” in Chapter 3.) Switches GPS function on and off.
Using the Touchpad CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may damage the touchpad surface. NOTES: A touchpad indicator is found on the keyboard panel, use the Fn+F7 hot keys to enable/disable this function. For optimal performance of the touchpad, keep your fingers and the pads clean and dry. When tapping on the pad, tap lightly. Do not use excessive force.
Term Action Point Move your finger on the pad until the cursor points to the selection on the screen. Click Press and release the left button. –or– Tap gently anywhere on the pad. Doubleclick Press and release the left button twice in quick succession. –or– Tap twice on the pad rapidly. Drag and drop Press and hold the left button, then move your finger until you reach your destination (drag). Finally, release the button (drop) when you finish dragging your selection to the destination.
Configuring the Touchpad You may want to configure the touchpad to suit your needs. For example, if you are a left-handed user, you can swap the two buttons so that you can use the right button as the left button and vise versa. You can also change the size of the on-screen pointer, the speed of the pointer, and so on. To configure the touchpad, you can use the standard Microsoft or IBM PS/2 driver if you are using Windows.
Using the Touchscreen (option) CAUTION: Do not use a sharp object such as a ballpoint pen or pencil on the touchscreen. Doing so may damage the touchscreen surface. The touchscreen is a touch-sensitive device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons. The touchscreen needs a special device driver support that allows you to easily use the computer without any external pointing device.
Using the Hard Disk Drive Your computer comes with a hard disk drive as drive C. The system has a built-in heater that automatically turns on for low temperature operation. The AC in / HDD heater on indicator blinks red when heater is on. AC in / HDD heater on indicator A hard disk drive is a storage device with non-removable, rotating, magnetic storage platters inside it. It is where your operating system and application software programs are stored. Your hard disk drive is a 2.
Using the CD/DVD Drive (option) Depending on the model, your computer comes with a CD R-W or DVD-Combo drive. This drive is usually configured as drive D and is connected through the CD drive bay located on the right side of the computer. The drive uses removable 5.25-inch silver discs, which look like standard music CDs. It is an ideal medium to use for distributing multimedia because of the huge amount of data that a disc can store.
NOTE: For DVD-Combo drive only. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Inserting and Removing a CD NOTE: The following procedure applies to inserting or removing a DVD disc as well. Follow this procedure to insert or remove a CD. 1. Turn on the computer. 2. Press the eject button and the CD tray will slide out partially. Gently pull on it until it is fully extended. 3. To insert a CD, place down the CD in the tray with its label facing up. Slightly press the center of the CD until it clicks into place.
Using the Video Features The video subsystem of your computer features: 12.1/13.3-inch TFT (Thin-Film Transistor) color LCD display with 1024x768 XGA (Extended Video Graphics Array) resolution. 64 MB integrated video memory. Simultaneous display on LCD and external monitor, which is useful when you have a presentation as you can control the screen from your computer and face the audience at the same time.
Your computer has been set to a default resolution and number of colors before shipment. You can view and change display settings through your operating system. See your operating system documentation or online help for specific information. For displaying in higher resolutions, you can connect an external CRT monitor that supports higher resolutions. (See “Connecting an External Monitor” in Chapter 4 for more information.) The following table lists the display modes supported by your computer.
Using the Audio Features NOTES: To take advantage of the enhanced audio capabilities, the audio driver supplied with your computer must be installed (see chapter 6 for details). If you experience interference while recording, try lowering the microphone recording volume.
Connecting Audio Devices For higher audio quality, you can send or receive sound through external audio devices. Microphone Connector ( ) can be connected to an external microphone for recording voice or sound. Audio Output Connector ( ) can be connected to the line-in connector of powered speakers with built-in amplifiers, headphones, or earphone set. This connector is compliant with S/P-DIF (Sony/Philips-Digital InterFace). You can connect audio equipment with S/P-DIF to the computer.
Using the Communication Features Using the LAN NOTE for Windows 2000: To take advantage of the LAN feature, the LAN driver supplied with your computer must be installed. The internal 100Base-T LAN (Local Area Network) module allows you to connect your computer to a network. It supports data transfer rate up to 100 Mbps. To connect the network cable to the LAN module, connect one end of the LAN cable to the RJ-45 connector on the computer and the other end to the network hub.
Using the Wireless LAN Depending on your model, an internal Mini PCI wireless LAN (WLAN) card may have been pre-installed by your computer manufacturer at the factory. This card allows you to access corporate networks or the Internet in a wireless environment. The WLAN features include: IEEE 802.11b standard compliance 2.
Turning Off/On the WLAN NOTE: The FAA (Federal Aviation Agency) has deemed it unsafe to operate wireless devices in aircraft as this may interfere with flight safety. Remember to select turn off wireless LAN when using your computer in the airplane. Upon booting-up your computer, the WLAN function is on. To turn off the WLAN function, turn off the WLAN utility. It takes approximately 30 seconds for your computer to make a successful WLAN connection and approximately 10 seconds to disconnect.
Your computer can send and receive data via a mobile network using the GSM protocol. To send or receive data over a GSM network, you must have an account with a service provider that supports GSM data services, and the service provider must enable the data features on your account.
positions accurate to a matter of meters. In fact, with advanced forms of GPS you can make measurements to better than a centimeter! In a sense it is like giving every square meter on the planet a unique address. Here's how GPS works in five logical steps: The basis of GPS is "triangulation" from satellites. To "triangulate," a GPS receiver measures distance using the travel time of radio signals. To measure travel time, GPS needs very accurate timing that it achieves with some tricks.
2-26 Operating Your Computer
CHAPTER 3 Managing Power Your computer operates either on external AC power or internal battery power. This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way.
AC Adapter CAUTION: The AC adapter is designed for use with your computer only. Connecting the AC adapter to another device can damage the adapter. The AC power cord supplied with your computer is for use in the country where you purchased your computer. If you plan to go overseas with the computer, consult your dealer for the appropriate power cord. When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer.
Battery Pack The battery pack is the internal power source for the computer. It is rechargeable using the AC adapter. The operating time of a fully charged battery pack depends on how you are using the computer. When your applications often access peripherals, you will experience a shorter operating time. NOTE: Care and maintenance information for the battery is provided in the “Battery Pack Guidelines” section in Chapter 7.
Initializing the Battery Pack You need to initialize a new battery pack before using it for the first time or when the actual operating time of a battery pack is much less than expected. Initializing is the process of fully charging, discharging, and then charging. It can take several hours. 1. Make sure the computer power is turned off. Connect the AC adapter to fully charge the battery pack. 2. After the battery pack is fully charged, turn on the computer. 3.
Replacing the Battery Pack CAUTION: There is danger of explosion if the battery is incorrectly replaced. Replace the battery only with the computer manufacturer’s optional battery packs. Discard used batteries according to the dealer’s instructions. Do not attempt to disassemble the battery pack. If you often rely on battery power for a long period of time while traveling, you may consider the purchase of an additional battery pack from your dealer and keep it with you in a fully charged state as a backup.
Battery Low Signals and Actions Battery Low occurs when the battery has approximately 10% (Windows default setting) of its charge remaining. The computer gives warning beeps or messages and the Battery Charge Indicator ( ) blinks red to alert you to take actions. NOTE: You can set up your threshold and signals of Battery Low under Windows. Immediately save your data upon Battery Low. The remaining operating time depends on how you are using the computer.
Power Management Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving. With an ACPI-compliant operating system such as Windows 2000 and Windows XP, power supply to different computer components is controlled on an as-needed basis. This allows maximum power conservation and performance at the same time.
When you use the hibernation feature, you do not have to close the applications. The computer stores the state of your computer to a file on the hard disk and then shut down. The next time you turn on your computer, you return to exactly where you left off.
Power-Saving Tips In addition to your computer’s automatic power management, you can do your part to maximize the battery’s operating time by following these suggestions. Do not disable Power Management. Decrease the LCD brightness to the lowest comfortable level. Disable the parallel and serial ports if no devices are connected to these ports. (See “Components Menu” in Chapter 5.) If you work with an application that uses the serial port, exit the application when you finish using it.
3-10 Managing Power
CHAPTER 4 Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter.
Connecting an External Monitor If you want the benefits of a larger display screen with higher resolution, you can connect an external CRT monitor to your computer. Follow this procedure to connect an external monitor: 1. Make sure that the computer is not turned on. 2. Plug the monitor’s signal connector to the computer’s DVI-I port. Connect to external monitor 3. Plug one end of the monitor’s power cord into the power socket on the monitor and the other end to an electrical outlet. 4.
Connecting a USB Device NOTE: To take advantage of the USB 2.0 feature, the USB 2.0 driver supplied with your computer must be installed (see chapter 6). Your computer has four USB ports that supports transfer rates up to 12 MB/s for USB 1.1 devices and 480 MB/s for USB 2.0 devices, such as digital camera, scanner, printer, modem, and mouse. USB is specified to be an industry standard extension to the PC architecture.
Connecting a Serial Device Your computer has a serial port for connecting a serial device such as an external modem. Follow this procedure to connect a serial device: 1. Make sure the “COM1 Ports” item is set properly in the SCU program. (See “Components Menu” in Chapter 5 for information.) 2. Make sure the computer is not turned on. 3. Plug the device cable to the serial port on the rear of the computer. 4. Turn on the computer.
Connecting an IR or Bluetooth-compliant Device NOTE: To take advantage of the Bluetooth feature, the Bluetooth driver supplied with your computer must be installed (see chapter 6 for details). Your computer has an IR (infrared) / Bluetooth port for connecting an infrared-equipped / Bluetooth-compliant device wirelessly such as another computer, printer, or PDA (Personal Digital Assistant). Follow this procedure to connect an IR device: 1.
4-6 Expanding Your Computer
Connecting an IEEE 1394 Device Your computer has an IEEE 1394 port on the right side of the computer for connecting 1394 devices. IEEE 1394 is the next-generation serial bus standard, featuring high-speed data transfer, multi-channel communication link, and “Hot Plug” connectivity. It allows connection of up to 63 devices. The applications include not only computer peripheral devices such as scanner, printer and high-quality CCD, but also consumer electronic equipment such as DVCAM and VCR.
Connecting a Video Capture Device NOTE: To take advantage of the AV input port, the Video Capture driver supplied with your computer must be installed (see chapter 6 for details). Your computer has an AV input port on the rear of the computer for connecting a video capture device such as high-quality CCD, as well as consumer electronic equipment such as DVCAM and VCR. To connect a video capturing device, simply plug the device cable to the AV input port (conexant 878A PCI; BNC-type) of the system.
System Memory Upgrade You can upgrade your computer by changing system memory to a maximum of 1 GB on the two 200-pin PC2100 DDR SO-DIMM slots. However, to avoid damage during the installation procedure, please ask your dealer for help.
4-10 Expanding Your Computer
CHAPTER 5 Setup Configuration Utility (SCU) SCU is a program for configuring the BIOS (Basic Input/Output System) settings of the computer. BIOS is a layer of software, called firmware, that translates instructions from other layers of software into instructions that the computer hardware can understand. The BIOS settings are needed by your computer to identify the types of installed devices and establish special features. This chapter tells you how to use the SCU program.
When and How to Use the SCU Program When to Use You need to run the SCU program when: You see an error message on the screen requesting you to run Setup. You want to restore the factory default settings. You want to modify some specific settings according to the hardware. You want to modify some specific settings to optimize system performance. Starting SCU NOTES: The Setup screens shown in this chapter are for your reference only. The actual items or settings on your computer may differ.
The menu can be divided into four areas: On the top line is the menu bar containing the titles of the available menus. Each menu title brings a specific menu. The center left column of the menu contains information regarding the current settings of the system. If you open a pull-down menu and select an item that provides multiple options, the left column will display a submenu where you can make further selections. The right column of the menu contains details of the CPU and system memory.
Moving Around and Making Selections A brief description of keyboard usage is listed next: Key Function ←, → Selects a menu title. ↑, ↓ 1) Selects an item or option. 2) Brings up/down the value. Enter 1) Brings up the sub-menu when available. 2) Opens or closes the options window when an item is selected. Tab Jumps from one item to another. Esc 1) Exits the SCU program. 2) Returns to the previous menu if in a sub-menu. 3) Closes the options window if one is open.
Startup Menu The Startup menu contains the basic configuration setting of the system, the sequence of the devices to be searched for the operating system, and a security setting that safeguards your system against unauthorized use.
Sets the system time (Hour, Minute, Second) and date (Month, Day, Year). Boot Device Sets the first, second, third, and fourth booting device. The system will try to boot from the first device but if it is not available, will try the next boot device. If you set the first boot device to PXE LAN, the system will boot from the LAN server first. The options are Hard Disk C, CD-ROM Drive, Diskette A, and PXE LAN. The default setting is Diskette A, Hard Disk C, CD-ROM Drive, then PXE LAN.
Set Password Allows you to set the password for your system. When typing the password, first make sure that Num Lk is off, then type your password in the entry fields and press Enter. Confirm your password by typing it again and pressing Enter.
Disks Menu The Disks menu contains a security setting that safeguards your system against viruses. Virus Alert Sets if a warning message will appear when the hard disk boot sector (partition table) has been changed. A checkmark ( ) indicates enabled, while an underline (_) indicates disabled. The default setting is disabled. CAUTION: Set this item to disabled before installing an operating system, running Fdisk or Format program. Otherwise, the intended action will fail.
Components Menu The Components menu contains a security setting that safeguards your system against viruses.
Allows you to configure the IR port of the computer. COM1/2/3/4 Settings sets the I/O (Input/Output) address and the Interrupt ReQuest line (IRQ) settings of the IR port. The options are Disabled; COM1, 3F8, IRQ4; COM2, 2F8, IRQ3; COM3, 3E8, IRQ6; COM4, 2E8, IRQ11. Mode Setting for COM2 sets the communication compatibility mode according to the type of the IR device to be connected. The options are IrDA (HPSIR) and Fast IR. The default setting is Fast IR.
Port Address sets the I/O address and the interrupt request line settings of the parallel port. The options are None; LPT1, 378, IRQ 7; LPT2, 278, IRQ 5;and LPT3, 3BC, IRQ 7. Default setting is LPT1, 378, IRQ 7. Port Definition sets the operating mode for the parallel port according to the type of the parallel device to be connected.
The Enable USB Port sub-item enables or disables the USB port in DOS mode. The options are enable and disable. A [X] mark indicates enable, while blank [ ] indicates disable. Default setting is enable. The USB Keyboard sub-item enables or disables the USB keyboard in DOS mode. The options are Enable and Disable. Default setting is Enable. This item is not valid for setting if the Enable USB Port sub-item is disabled. The USB Floppy sub-item enables or disables the USB floppy drive in DOS mode.
Exit Menu The Exit menu allows you to leave the SCU program. After finished with your settings, you must save and exit so that the new settings can take effect. Save and Exit saves the changes you have made and exit the SCU program. Exit (No Save) exits the SCU program without saving the changes you have made. Default Settings loads factory default values for all the items. Restore Settings restores previous values for all the items. Version Info displays the BIOS version information.
5-14 Setup Configuration Utility (SCU)
CHAPTER 6 Installing Software Drivers To take full advantage of the unique features of your computer, some operating systems require custom software, known as drivers, to be installed. If you purchased the computer with Windows pre-installed, your dealer may have already installed the drivers. If not, you need to install the drivers using the CD supplied with your computer. This chapter describes how to install the drivers.
How to Use the CD NOTES: • The drivers may have been updated after this manual was published. For driver upgrade, please contact your dealer. • You can always find README or document files on the CD. These files contain the latest information from the software supplier. Please read the files together with this chapter. • This CD supports Windows 2000 and Windows XP only. • The available items may differ according to your computer model and operation system.
Installing Drivers for Windows 2000 To set up the necessary drivers for Windows 2000, click on “Windows 2K” on the initial screen. The following screen appears: To install the necessary driver, just click on the particular option and follow the onscreen instructions to continue and complete installation. Application Chipset DirectX 8.1 Installing Software Drivers Installs the Intel® Application Accelerator to improve performance of the storage sub-system and overall system performance.
VGA Audio Allows you to select high-resolution displays with richer colors. It can drive LCD displays as well as CRT displays. Allows you to take full advantage of the audio subsystem. Upon clicking “Next Page,” the following screen appears: USB 2.0 LAN Touchpad Touchscreen PCI-952 6-4 Allows your system to connect to USB 2.0 devices. Allows you to use the network function of the computer. Allows you to take full advantage of the touchpad features.
NOTE: An extensive on screen instructions is provided, follow the steps outlined to install the driver. Upon clicking “Next Page,” the following screen appears: Mini-PCI Installs the WLAN driver allows you to use the internal Mini PCI WLAN card. NOTE: An extensive on screen instructions is provided, follow the steps outlined to install the driver. USB-to-LAN Fingerprint Allows you to use the network function of the computer through the optional docking station (if connected).
NOTE: An extensive on screen instructions is provided, follow the steps outlined to install the driver. Bluetooth Allows you to use the bluetooth port to connect to bluetooth-compliant devices. Touchscreen Driver To install the touch screen driver, perform the following: 1. Insert the driver CD into the drive. 2. Click on “Windows 2K”, then “Touchscreen” and follow the onscreen instructions to continue. 3. When finished installing, select “Yes” to reboot your system. The driver should now be loaded. 4.
Installing Drivers for Windows XP To set up the necessary drivers for Windows XP, click on “Windows XP” on the initial screen. The following screen appears: To install the necessary driver, just click on the particular option and follow the onscreen instructions to continue and complete installation. Application Chipset VGA Installing Software Drivers Installs the Intel® Application Accelerator to improve performance of the storage sub-system and overall system performance.
Audio Allows you to take full advantage of the audio subsystem. USB 2.0 Allows your system to connect to USB 2.0 devices. Upon clicking “Next Page,” the following screen appears: Touchpad Mini-PCI Allows you to take full advantage of the touchpad features. Installs the WLAN driver allows you to use the internal Mini PCI WLAN card. NOTE: An extensive on screen instructions is provided, follow the steps outlined to install the driver.
Touchscreen Allows you to use your fingers as a pointing device (refer to the next section for further instructions). Upon clicking “Next Page,” the following screen appears: USB-to-LAN Fingerprint Allows you to use the network function of the computer through the optional docking station (if connected). Allows you to use the fingerprint recognition system and its application software. NOTE: An extensive on screen instructions is provided, follow the steps outlined to install the driver and utility.
Touchscreen Driver To install the touchscreen driver, perform the following: 1. Insert the driver CD into the drive. 2. Click on “Windows XP”, then “Touchscreen” and follow the onscreen instructions to continue. 3. Click on ”Start,” then “Control Panel.
4. Click on the “Performance and Maintenance” category.
5. Click on “System.
6. Click on “Hardware” folder, then click on “Device Manager.
7. Click on “? Unknown device,” then click on the “Properties” icon.
8. Click on “Reinstall Driver.” 9. When the “Hardware Update Wizard” appears, select “Install the software automatically [Recommended],” then click on “Next.
10. Click on “Continue Anyway.
11. Click on “Finish.
12. When the “PenMount DMC9000 and DMC9100 Properties” screen appears, click on “Close” to exit the driver installation. Touchscreen Utility To install the touchscreen utility, perform the following: 1. Insert the driver CD into the drive.
2. Click on “Start”, then “Run.” 3. Enter the following directory on the driver CD: \TSRC\Setup.exe, then click on “OK.” 4. Select “Yes” to the question if this is the first time to run this setup. 5. When the “InstallShield Wizard” appears, click on “Next” to continue. 6. Select “I accept the terms in the license agreement,” then click on “Next.” 7. When the “Ready to Install the Program” screen appears, click on “Next” to continue. 8. Reboot the system.
6-20 Installing Software Drivers
CHAPTER 7 Caring for the Computer Taking good care of your computer will ensure a trouble-free operation and reduce the risk of damage to your computer.
Protecting the Computer To safeguard the integrity of your computer data as well as the computer itself, you can protect the computer in several ways as described in this section. Using the Password The power-on password protects your computer against unauthorized use. If the password is set, the prompt requesting for the password appears on the screen whenever the computer is turned on. The password is set via the SCU program. See “Startup Menu” in Chapter 5 for instructions.
Taking Care of the Computer Location Guidelines Use the computer where the temperature is between 0 °C (32 °F) and 50 °C (122 °F). Avoid placing the computer in a location subject to high humidity, extreme temperatures, mechanical vibration, direct sunlight, or heavy dust. Do not cover or block any ventilation openings on the computer. For example, do not place the computer on a bed, sofa, rug, or other similar surface. Otherwise, overheating may occur that results in damage to the computer.
Cleaning Guidelines Never clean the computer with its power on. Use a soft cloth moistened with water or a non-alkaline detergent to wipe the exterior of the computer. Gently wipe the display with a soft, lint-free cloth. Do not use alcohol or detergent on the display. Dust on the IR/Bluetooth port can interfere with data transfer. Wipe the port with a soft, dry cloth. Dust or grease on the touchscreen can affect its sensitivity.
When Traveling Before traveling with your computer, make a backup of your hard disk data into floppy disks or other storage devices. As an added precaution, bring along an extra copy of your important data. Make sure the battery pack is fully charged. Make sure the computer is turned off. Do not leave objects that will press onto the display. Disconnect the AC adapter from the computer and take it with you. Use the AC adapter as the power source and as a battery-charger. Hand-carry the computer.
7-6 Caring for the Computer
CHAPTER Troubleshooting Hardware, software, or a combination of both can cause computer problems. When you encounter any problem, it might be a typical problem that can easily be solved. This chapter tells you what actions to take when solving common computer problems.
Preliminary Checklist Here are helpful hints to follow before you take further actions when you encounter any problem: Try to isolate which part of the computer is causing the problem. Make sure that you turn on all peripheral devices before turning on the computer. If an external device has a problem, make sure that the cable connections are correct and secure. Make sure that the configuration information is properly set in the SCU program. Make sure that all the device drivers are correctly installed.
Solving Common Problems For easy reference, the problems are divided into these categories. Problem Type Go to Battery Problems P. 8-4 CD R-W / DVD-Combo Drive Problems P. 8-4 Display Problems P. 8-5 Fingerprint Recognition Problems P. 8-7 Hardware Device Problems P. 8-7 Hard Disk Drive Problems P. 8-8 Infrared Problems P. 8-8 Keyboard, Mouse and Touchpad Problems P. 8-9 LAN Problems P. 8-9 WLAN Problems P. 8-10 Modem Problems P. 8-10 Power Management Problems (for Windows) P.
Battery Problems The battery does not charge (Battery Charge indicator does not light amber). Make sure that the AC adapter is properly connected. Make sure that the battery is not too hot or cold. Allow time for the battery pack to return to room temperature. Make sure that the battery pack is installed correctly. Make sure that the battery terminals are clean. The operating time of a fully charged battery becomes shorter.
You cannot eject a CD. The CD is not properly seated in the drive. Manually release the CD following the method described next: 1. Turn off the system. 2. Insert a small rod, such as a straightened paperclip, into the drive’s manual eject hole and push firmly to release the tray. 3. Pull the tray out until fully extended, and then remove the CD. Display Problems Nothing appears on the screen. If the power-on indicator is not on, check the electrical outlet, the plugs and power cords.
The brightness level might be too low. Increase brightness by pressing Fn+F6. The display output might be set to an external device. To switch the display back to the LCD, press Fn+F9, or change the display through the settings in Display Properties. Reset the computer by pressing the keyboard BIOS reset switch on the left side of the computer or by pressing Ctrl+Alt+Del keys. Try turning the computer off, wait for a few seconds, then turn it back on. The characters on the screen are dim.
Switch the display to the monitor by pressing Fn+F9, or change the display through the settings in Display Properties. Simultaneous display/multi-display does not work. Make sure that you turn on the external monitor before turning on the computer. Press Fn+F9 to toggle through the display options or change the settings in Display Properties in Windows. Fingerprint Recognition Problems The fingerprint recognition application does not work. Make sure that the necessary driver is correctly installed.
Hard Disk Drive Problems The hard disk drive error message appears on the screen. Insert a bootable diskette and check the integrity of your hard drive. The hard disk drive has defects. Ask your dealer for help. The hard disk drive operations seem slow. The data files stored on the hard disk drive may be fragmented. Use a tool such as Window’s Disk Defragmenter to defragment the files. The hard disk drive in-use indicator glows without blinking.
Make sure that the IR ports are clean. Keyboard, Mouse and Touchpad Problems The keyboard does not respond. Try connecting an external keyboard. If it works, contact an authorized dealer, as the internal keyboard cable might be loose. The numeric keypad is disabled. Make sure that the Num Lk is switched on. (Check if the Num Lock Indicator glows or not.) The external keyboard does not work. Make sure that the keyboard cable is properly connected. The USB mouse does not work.
WLAN Problems I cannot use the WLAN feature. Make sure that the Mini PCI WLAN card is correctly installed. Make sure that the necessary driver(s) is correctly installed. Make sure that the WLAN feature is turned on. Transmission quality is poor. Your computer may be in an out-of-range situation. Move your computer closer to the Access Point or another WLAN device it is associated with. Check if there is high interference around the environment and solve the problem as described next.
If the operating radio channel is in poor quality, change the Access Point and all the wireless station(s) within the BSSID to another radio channel. Your computer may be in an out-of-range situation. Move your computer closer to the Access Point it is associated with. Make sure that your computer is configured with the same security option (encryption) to the Access Point. Use the Web Manager/Telnet of the Access Point to check whether it is connected to the network. Reconfigure and reset the Access Point.
Power Management Problems (for Windows) The computer does not enter Standby or Hibernation mode automatically. If you have a connection to another computer, the computer does not enter Standby or Hibernation mode if the connection is actively in use. Make sure that the Standby or Hibernation time-out is enabled. The computer does not enter Standby or Hibernation mode immediately. If the computer is performing an operation, it normally waits for the operation to finish.
Make sure that the printer port is enabled in the SCU program. The printer prints garbled information. Make sure that the printer driver is correctly installed. Make sure that the printer cable is properly connected. Software Problems An application program does not work correctly. Make sure that the software is correctly installed. If an error message appears on the screen, consult the software program’s documentation for further information. If you are sure the operation has stop, reset the computer.
The external microphone or audio device does not work. Make sure that the microphone is connected to the proper connector on the computer. Make sure that your computer is equipped with the driver needed. Click the speaker symbol on the taskbar and check the Windows volume control. Check the volume control of your computer. Startup Problems When you turn on the computer, it does not respond and the Power Indicator does not light green.
If you are booting from the hard disk, make sure that there is no floppy disk in the floppy disk drive. If there is, remove it and restart the system. If this message appears when you are booting from the hard disk, insert a bootable disk in the floppy disk drive and check the condition of the hard disk. Make sure that the hard disk is set correctly in the SCU program. Other Problems The date/time is incorrect. Correct the date and time via the operating system or SCU program.
Resetting the Computer You may have to reset (reboot) your computer on some occasions when an error occurs and the program you are using hangs up. If the system operation seems to hang up, first wait. It is possible that the system is processing data. Periodically check the hard disk drive in-use indicator, if it flashes irregularly, the program may be accessing data and preventing you from using the keyboard.
APPENDIX A Specifications NOTE: Specifications are subject to change without any prior notices. Parts Specifications CPU Intel Mobile Pentium 4 Processor-M series microprocessor, µ-FCPGA package, 1.7 GHz; Front Side Bus (FSB) 400 MHz with SpeedStep function Cache Memory ROM BIOS RAM System L2 512 KB on-die 512 KB Flash EEPROM, PC2001-compliant Two 200-pin PC2100 DDR SO-DIMM sockets, maximum 1 GB (standard 256 MB) 64 MB (integrated DDR memory) 12.1/13.
Parts I/O ports IR port and Bluetooth port, Mic-in, Line-out On right side On rear side IEEE 1394 port, two USB ports, RJ-11 fax/modem port DVI-I port, serial port, docking port for Port Replicator / car mount, two USB ports, AV input port, AC-in On keyboard panel LAN Wireless LAN Wireless Modem GPS Power AC adapter Battery Dimension (W×D×H) Weight Environment Temperature Humidity A-2 Specifications On left side Fingerprint recognition system 10/100Base-T Mini PCI (option) GSM/GPRS, iDEN, DataTAC,
APPENDIX B Fingerprint Recognition System Your system features a fingerprint recognition system that can: • display fingerprint images derived from the sensor IC • enroll new users • extract fingerprint templates from raw images, and store them in a local database • match live-scan fingerprints against the local database
Finger Placement When placing a finger to be enrolled or identified, slide the cover to expose the sensor matrix surface, then use a light, but firm and steady pressure. Avoid moving your finger during the scan, and be sure that you are making contact with the “sensor matrix” and with the surrounding drive ring (the light-colored surface surrounding the matrix.
Using the Application NOTE: To take advantage of the fingerprint recognition system, the driver and utility supplied with your computer must be installed (see chapter 6 for details). Double-click on the icon located on your Windows’ system tray. The main menu appears.
B-4 Fingerprint Recognition System
