User`s manual

ManualsBrandsMotorola ManualsBarcode ReaderLS6000B-U

Laser Barcode Scanner

Model no.

LS6000B-U

QUICK GUIDE

INTRODUCTION

LS6000B-U laser barcode scanners series have incorporated the latest wireless

blue-tooth technology. The technology provides customer with the freedom of

mobility, with long communication range from the charging cradle.

The bar code scanner requires establishing communications with its charging

cradle (built-in dongle). After communications have been established between the

scanner and charging cradle, futures bar code scans will be transmitted from the

scanner to the cradle and from the cradle to the host.

For power supply, the charging cradle of LS6000B-U also works as a battery

charger for the scanner. Users can plug in 5V DC power adaptor for power charge

of the scanner.

Package of LS6000B-U series should contain:

1. LS6000B-U Laser Barcode Scanner

(Rechargeable Li-Ion battery pack inside)

2. Charging Cradle with USB cable & DC plug

3. Power Adaptor (5V/1A)

4. User’s Manual

RED BLUE ORANGE

ON Not read Good read

Continual ON

Off line / out of service

range

Low power

Blinking

Wireless connection not

linked

Charging

P.S. If scanner not in use, will automatic switch to sleeping

mode after 30 min.

* When out of service range the laser will on but will not scan.

INSTALLATION

Charging Cradle

Buzzer

Exit Window

Trigger

Handle

3 indicators (LED)

USB dongle

USB Zig-bee dongle

Summary of content (17 pages)

PAGE 1
INTRODUCTION LS6000B-U laser barcode scanners series have incorporated the latest wireless blue-tooth technology. The technology provides customer with the freedom of mobility, with long communication range from the charging cradle. The bar code scanner requires establishing communications with its charging cradle (built-in dongle).
PAGE 2
Insert the plug on the free end of the Communications Cable into the appropriate connector on the host as below described: USB Connection (RS232 data format) Connect with host Step 1: key-in a file name Step 2: select the first Step 3: press OK Figure 2 1. Please switch on and charging scanner for 6 hours at first time before install driver. 2. Install the software “PL-2303 Driver Installer.exe” to the host system for LS6000B-U series. No need to key-in 3.
PAGE 3
7. Start to aim the scanner at a bar code, you may see data shown on the hyper terminal. FCC Compliance Reset Configuration to Defaults If you are unsure of the scanner configuration or have scanned the incorrect codes, please scan the “Reset Configuration to Defaults” barcode. This will reset the scanner to its factory settings.
PAGE 4
Multi-Interface Functions – 1 OUTPUT FIRMWARE VERSION RESET CONFIGURATION TO DEFAULTS 0A OUTPUT MODE – KEYBOARD / USB 0B OUTPUT MODE 000600 GOOD READ BEEP TONE – NONE Setup from Bar Code Label 000601 BUZZER / LED 014200 DECODE OPTIONS REVERSE IMAGE – ENABLE DECODE OPTIONS REVERSE IMANGE - DISABLE 01390 CODE ID 01400 DECODE OPTIONS SEND BAR CODE ID – AS A PREFIX 01401 DECODE OPTIONS SEND BAR CODE ID RESET 6 GOOD READ BEEP TONE - RESET 0B142 IMAGE 01391 DECODE OPTIONS SEND BAR CODE ID DIS
PAGE 5
Multi-Interface Functions – 2 SCAN MODE – SINGLE SCAN READING MODE Interface – KBW SCAN MODE – SINGLE SCAN NO TRIGGER WEDGE MODE - AUTODETECT 013300 013301 SCAN MODE – MULTISCAN SCAN MODE – MULTISCAN NO TRIGGER 000200 TRANSMIT SPEED - 0 013302 PC Communication WEDGE MODE – SCAN SET 2 PASS THRU 000204 TRANSMIT SPEED TRANSMIT SPEED - 25 013303 SCAN MODE - PULSE 0000000 0000025 LANGUAGE 013305 LASER/CCD TIMEOUT – 5 SECONDS KEYBOARD COUNTRY - USA KEYBOARD COUNTRY - GERMAN 0005000 0005010
PAGE 6
Interface – Serial - 1 Interface – Serial - 2 BAUD RATE SERIAL BAUD RATE - 2400 SERIAL BAUD RATE - 4800 000703 PARAMETERS SERIAL DATA BITS - 8 SERIAL DATA BITS - 7 000704 00081 00080 SERIAL BAUD RATE - 9600 SERIAL BAUD RATE - 19200 SERIAL STOP BITS - 1 SERIAL STOP BITS - 2 000705 000706 00090 00091 SERIAL PARITY - NONE SERIAL PARITY - ODD 001000 001001 SERIAL HANDSHAKE - NONE HAND SHAKE 001200 SERIAL HANDSHAKE – XON/XOFF 001201 SERIAL PARITY - MARK SERIAL PARITY - EVEN SERIAL HAND
PAGE 7
Symbologies On/Off - 2 Symbologies On/Off - 1 CODE 11 - ENABLE CODE 11 01261 CODE 39 ENABLE CODE 93 CODE 11 - DISABLE 01260 CODE 39 00221 CODE 39 DISABLE 00220 FULL ASCII ENABLE FULL ASCII DISABLE 00231 00230 CODE 93 - ENABLE CODE 93 - DISABLE 00620 00621 CODE 128 - ENABLE CODE 128 00691 00690 CODE 128 ISBT - ENABLE CODE 128 ISBT - DISABLE 00701 00700 CODABAR - ENABLE CODABAR I2OF5 - ENABLE INTERLEAVED 2 OF 5 00961 ID2OF5 - ENABLE CODABAR - DISABLE 00850 00851 I2OF5 - DISABL
PAGE 8
Symbologies Set Up - 1 Symbologies On/Off - 3 CODE 11 MSI CODE 11 ID CHARACTER – “m” CODE 11 ID CHARACTER – “Z” 0131m 0131Z UPC-A DISABLE CODE 11 LASER/CCD REDUNDANCY ENABLE CODE 11 LASER/CCD REDUNDANCY DISABLE 00341 00340 01321 UPC-E ENABLE UPC-E DISABLE 00351 00350 MSI - ENABLE MSI - DISABLE 01151 01150 UPC-A ENABLE UPC/EAN EAN-13 ENABLE EAN-13 DISABLE 00361 00360 EAN-8 ENABLE EAN-8 DISABLE 00370 00371 14 CODE 39 SS CHAR - NONE 01320 CODE 39 CODE 39 SS CHAR ‛+’ 002700
PAGE 9
Symbologies Set Up – 2 Symbologies Set Up – 3 CODE 93 CODE 93 ID CHARACTER – “h” CODE 93 ID CHARACTER – “Z” 0066h 0066Z CODE 93 LASER/CCD REDUNDANCY ENABLE CODE 93 LASER/CCD REDUNDANCY DISABLE 00681 00680 CODABAR ID CHARACTER –‛k’ CODABAR 0094k 0094Z CODABAR LASER/CCD REDUNDANCY - ENABLE CODABAR LASER/CCD REDUNDANCY - DISABLE 00951 CODE 128 ID CHARACTER – ‛g’ CODE 128 0081Z CODE 128 LASER/CCD REDUNDANCY ENABLE CODE 128 LASER/CCD REDUNDANCY DISABLE CODABAR SEND START/STOP CHARS ENABLE
PAGE 10
0113j 0113Z 00481 00480 Symbologies Set Up – 4 ID2OF5 LASER/CCD REDUNDANCY ENABLE ID2OF5 LASER/CCD REDUNDANCY DISABLE 01141 01140 MSI MSI CHECK DIGIT – MOD 10 MSI CHECK DIGIT –RESET 01160 0B116 MSI ISBN ID CHARACTER –‛f’ MSI ISBN ID CHARACTER –‛Z’ 0053f 0053Z MSI LASER/CCD REDUNDANCY ENABLE MSI LASER/CCD REDUNDANCY DISABLE 01251 EXPAND UPC-E TO UPC-A ENABLE 01250 UPC/EAN EXPAND UPC-E TO UPC-A DISABLE 00381 00380 EXPAND UPC-A TO EAN-13 ENABLE EXPAND UPC-A TO EAN-13 DISABLE 00391 CO
PAGE 11
Symbologies Set Up – 5 SEND UPC-A CHECK DIGIT ENABLE Symbologies Set Up – 6 SEND UPC-A CHECK DIGIT DISABLE EAN-8 ID CHARACTER ‛d’ EAN-8 ID CHARACTER ‛Z’ UPC/EAN 00421 SEND UPC-E CHECK DIGIT ENABLE 00420 SEND UPC-E CHECK DIGIT DISABLE 00431 SEND EAN-13 CHECK DIGIT ENABLE 00430 SEND EAN-13 CHECK DIGIT DISABLE 00461 SEND EAN-8 CHECK DIGIT ENABLE 00460 SEND EAN-8 CHECK DIGIT DISABLE 00471 00470 UPC-A ID CHARACTER ‛b’ UPC-A ID CHARACTER ‛Z’ 0049b 0049Z UPC-E ID CHARACTER ‛c’ UPC-E ID CHARACTER ‛
PAGE 12
EDIT SETUP BAR CODES EDIT #1 – STRIP 1 LEADING CHARACTER MACRO/SPECIAL KEYS SETUP BAR CODES EDIT #1 - OFF ON ALL BAR CODES THAT START WITH MACRO #1 – FIND ‛1’ AND REPLACE WITH MACRO #1 - DISABLED ‛ONE’ ‛12345’ 02000101000000100000000112345 0B20001 02010101011ONE 0B20101 EDIT #2 – STRIP 1 TRAILING CHARACTER EDIT #2 – OFF MACRO #2 – FIND ‛2’ AND REPLACE WITH ‛TWO’ FOR CODE 39 ONLY MACRO #2 - DISABLED 020002020000001 0B20002 0201023012TWO 0B20102 EDIT #1 – FILTER LEADING SPACES EDIT #1 -
PAGE 13
TERMINATION STRING SETUP BAR CODES STRING #1 – TERMINATION CHAR - CR STRING #1 – TERMINATION - LF 0202011000$0D 0202011000$0A STRING #1 – TERMINATION CR+LF STRING #1 - DISABLE 0202011000$0D$0A 0B20201 STRING #2– CODE 128 TERMINATION CHAR CR STRING #2 – CODE 128 TERMINIATION CHAR LF 0202021080$0D 0202021090$0A STRING #2– CODE 128 TERMINATION CHAR – CR+LF STRING #2– CODE 128 TERMINATION CHAR REMOVED 0202021080$0D$0A 0B20202 STRING – CODE 39 TERMINATION CHAR TAB STRING – CODE 39 TERMINATION CH
PAGE 14
Scanner Timing Default RS-232 communication Default Baud rate 9600 Parity None Data Bits 8 Stop Bit 1 RTS/CTS Off Terminator Keyboard Wedge Communication Default Terminal Type PC/AT Keyboard US keyboard Terminator Enter (Alpha numeric) USB Communication Default Terminator type Enter Code mode Scan Code Keyboard US keyboard Decoder Selection Default EAN/UPC Enable Code 39 Enable Code 32 Disable CODABAR Enable ITF 2 of 5 Enable MSI Disable Code 93 Enable Co
PAGE 15
a. Problem: Nothing happens when I follow the operating instructions. d. My computer gets a keyboard error while booting up. Possible Cause Possible Solution Possible Cause Possible Solution Interface cables are loose Check for loose cable connections The scanner is damaged or is no Disconnect the scanner from your longer functioning. computer and use your keyboard only. b. Problem: When I connected RS232 interface reader to PC, I could not get power up signal. Reboot your computer.
PAGE 16
f. Problem: The scanner beeps, but no data is displayed on my computer. h. Problem: Some of the barcode data is missing displayed on the host. Possible Cause Possible Solution Possible Cause Possible Solution Scanner is not programmed for the Please make sure the scanner is The scanner’s transmit speed is too For RS232, you can set up the correct host type. configured to the appropriate host type fast. scanner’s transmit speed.
PAGE 17
Version: 2.0 Date: November 11, 2008 P/N: 79.60002.