MC55 Enterprise Digital Assistant User Guide
MC55 Enterprise Digital Assistant User Guide 72E-108859-05 Rev.
ii MC55 User Guide © 2009-10 by Motorola, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis.
iii Revision History Changes to the original manual are listed below: Change Date Description -01 Rev. A 11/21/08 Initial release. -02 Rev. A 03/12/09 Add MC5574 configuration support. -03 Rev. A 03/15/10 Add support for OEM version 02.35.000 and 02.35.001. -04 Rev. A 09/07/10 Add support for OEM version 03.38.0004. -05 Rev. A 12/15/10 Add MC55A0 configuration.
iv MC55 User Guide
Table of Content Revision History .................................................................................................................................... iii About This Guide Introduction ........................................................................................................................................... Documentation Set ......................................................................................................................... Configurations................
vi MC55 User Guide Turning Off the Radios ................................................................................................................... Handstrap Replacement ...................................................................................................................... Removal ......................................................................................................................................... Installation ....................................................
Table of Contents Software Installation ............................................................................................................................ MC55 GPS Setup ................................................................................................................................ Operation ............................................................................................................................................. GPS Maps on microSD Cards ........................
viii MC55 User Guide Chapter 5: Using Bluetooth Introduction .......................................................................................................................................... Adaptive Frequency Hopping .............................................................................................................. Security ................................................................................................................................................
Table of Contents ix Available Services .......................................................................................................................... Object Push Services via Beam ............................................................................................... Internet Sharing ....................................................................................................................... Hands-free Services ................................................................
x MC55 User Guide Flat Surface Installation ........................................................................................................... 6-16 Chapter 7: Maintenance & Troubleshooting Introduction .......................................................................................................................................... Maintaining the MC55 ..........................................................................................................................
Table of Contents Audio Modes ........................................................................................................................................ Changing Audio Modes .................................................................................................................. Voice Packet Prioritization ................................................................................................................... Limitations ....................................................
xii MC55 User Guide
About This Guide Introduction This guide provides information about using the MC55 Enterprise Digital Assistant (EDA) and accessories. NOTE Screens and windows pictured in this guide are samples and can differ from actual screens. For configurations with OEM version 03.38.000X (and higher) and Windows Mobile 6.5 operating system, refer to Appendix C, Windows Mobile 6.5 for information about new features.
xiv MC55 User Guide Configurations This guide covers the following configurations: Configuration Data Capture Options Operating System Radios Display Memory Keypads MC5574 WLAN: 802.11 b/g WPAN: Bluetooth v2.0 EDR WWAN: GSM/GPRS/EDGE GPS: SiRF III 3.5” QVGA Color 128 MB RAM/ 256 MB Flash or 128 MB RAM/ 512 MB Flash 1D laser scanner, 2D imager, 1D laser scanner and camera or 2D imager and camera Windows Mobile 6.X Professional Numeric, QWERTY, QWERTZ, AZWERTY or PIM MC5590 WLAN: 802.
About This Guide xv The second line lists the operating system version and the build number. The last part of the build number represents the AKU number. For example, Build 20963.1.5.2 indicates that the device is running AKU version 1.5.2. OEM Version To determine the OEM software version: Tap Start > Settings > System tab > System Info icon > System tab. BTExplorer Software To determine the BTExplorer software version: NOTE For configurations with Windows Mobile 6.
xvi MC55 User Guide Fusion Software To determine the Fusion software version: Tap Wireless Strength icon > Wireless Status > Versions. Phone Software To determine the Phone software version: Tap Start > Phone > Menu > Options > PhoneInfo tab or Start > Setting > System > PhoneInfo icon.
About This Guide Chapter Descriptions Topics covered in this guide are as follows: • Chapter 1, Getting Started provides information on getting the MC55 up and running for the first time. • Chapter 2, Using the MC55 provides basic instructions for using the MC55, including powering on and resetting the MC55, and entering and capturing data. • Chapter 3, Using GPS Navigation provides information about GPS navigation with the MC55.
xviii MC55 User Guide Related Documents • MC55 Quick Start Guide, p/n 72-114971-xx. • MC55 Windows Mobile 6.1 Regulatory Guide, p/n 72-108860-xx. • MC55 Integrator Guide, p/n 72E-108861-xx. • Microsoft® Applications for Windows Mobile 6 User Guide, p/n 72E-108299-xx. • Mobility Services Platform User Guide, p/n 72E-100158-xx. • Enterprise Mobility Application Guide, p/n 72E-68901-xx. • Enterprise Mobility Developer Kits (EMDKs), available at: http://www.motorola.com/enterprisemobility/support.
Chapter 1 Getting Started Introduction This chapter lists the parts and accessories for the MC55 and explains how to set up the MC55 for the first time.
1-2 MC55 User Guide Battery Battery Latch Handstrap Speaker Camera Flash Camera Stylus Stylus Clip Action Button Exit Window Scan/Action Button Figure 1-2 MC55 Rear View Unpacking Carefully remove all protective material from the MC55 and save the shipping container for later storage and shipping.
Getting Started 1-3 Accessories Table 1-1 lists the accessories available for the MC55 EDA. Table 1-1 MC55 Accessories Accessory Part Number Description Cradles Single Slot USB Cradle CRD5500-1000UR Charges the MC55 main battery and a spare battery. Synchronizes the MC55 with a host computer through a USB connection. Single Slot Ethernet/Modem/USB Cradle CRD5500-1000XR Charges the MC55 main battery and a spare battery.
1-4 MC55 User Guide Table 1-1 MC55 Accessories (Continued) Accessory Part Number Description Stylus Stylus-00005-03R Stylus-00005-50R Replacement stylus for MC55A0-HC (3-pack) Replacement stylus for MC55A0-HC (50-pack) Spring Loaded Stylus STYLUS-00001-03R STYLUS-00001-10R Optional spring loaded stylus (3-pack). Optional spring loaded stylus (10-pack).
Getting Started 1-5 Rubber access door SIM card holder door microSD card holder door Figure 1-3 Lift SIM Slot Holder Door 4. Lift microSD card holder door. 5. Insert the microSD card into card holder door ensuring that the card slides into the holding tabs on each side of the door. microSD card Holding tab Figure 1-4 Insert microSD Card in Holder 6. Close the card holder door and push down until it is securely into place. 7. Close SIM card holder door and slide down until it locks into place.
1-6 MC55 User Guide NOTE For more information about SIM cards, refer to the service provider's documentation. To install the SIM card: 1. Lift rubber access door. 2. Slide the SIM card holder up to unlock. 3. Lift the SIM card holder door. Figure 1-5 Lifting the SIM Cover 4. Insert the SIM card, as shown in Figure 1-6 ensuring that the card slides into the holding tabs on each side of the door. Figure 1-6 Inserting the SIM Card 5. Close SIM card holder door and slide down to lock into place.
Getting Started 1-7 Installing the Battery NOTE The MC55 ships with either a 2400 mAh or 3600 mAh battery. The 2400 mAh battery is shown in this installation procedure. To install the battery. 1. Insert the battery, bottom first, into the battery compartment in the back of the MC55. 2. Press the battery down into the battery compartment until the battery release latch snaps into place.
1-8 MC55 User Guide removed for several hours. The backup battery retains RAM data in memory for at least 15 minutes (at room temperature) when the MC55A0’s main battery is removed. When the MC55A0 reaches a very low battery state, the combination of main battery and backup battery retains RAM data in memory for at least 48 hours. For cable and cradle setup and charging procedures refer to the MC55 Integrator Guide.
Getting Started 1-9 Charging Temperature Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Note that charging is intelligently controlled by the MC55. To accomplish this, for small periods of time, the MC55 or accessory alternately enables and disables battery charging to keep the battery at acceptable temperatures. The MC55 or accessory indicates when charging is disabled due to abnormal temperatures via its LED. See Table 1-2.
1 - 10 MC55 User Guide Battery Latch 1 2 Figure 1-8 Removing the Battery 4. Lift the battery from the MC55. 5. Insert the replacement battery, bottom first, into the battery compartment in the back of the MC55. 6. Re-attach the handstrap. 7. Press the battery down until the battery release latch snaps into place. The MC55 powers up after inserting the battery. Removing the microSD Card To remove an microSD card: 1. Press the red Power button to suspend the MC55.
Getting Started 1 - 11 Battery Management Observe the following battery saving tips: • Leave the MC55 connected to AC power at all times when not in use. • Set the MC55 to turn off after a short period of non-use. • Set the backlight to turn off after a short period of non-use. • Turn off all wireless activities when not in use. Changing the Power Settings To set the MC55 to turn off after a short period of non-use: 1. Tap Start > Settings > System tab > Power icon > Advanced tab. 2.
1 - 12 MC55 User Guide Turning Off the Radios NOTE On devices with Windows Mobile 6.5.3, see Status Bar on page C-5 for more information. Windows Mobile 6.1 devices include Wireless Manager, which provides a simple method of enabling, disabling, and configuring all the device’s wireless capabilities in one place. To open Wireless Manager, tap the Connectivity icon or tap Wireless Manager on the Today screen. Connectivity icon Figure 1-9 Opening Wireless Manager Select Wireless Manager.
Getting Started 1 - 13 Figure 1-11 Wireless Manager Menu Handstrap Replacement Removal To remove a handstrap from the MC55: 1. Slide the handstrap clip out of the handstrap slot. Figure 1-12 Handstrap Clip Removal 2. Press the red Power button to suspend the MC55. On the MC55A0, the PowerKey Action window appears. Tap Safe Battery Swap. The Decode LED lights red and then turns off. 3. Remove the battery. CAUTION 4. When removing handstrap pin, be carefully not to damage handstrap mounting area.
1 - 14 MC55 User Guide 5. Pry the handstrap and pin up and out of the handstrap mount area. 1 2 3 4 Figure 1-13 Handstrap and Pin Removal 6. Repeat for the other side of the handstrap. 7. Remove pin from the handstrap. Figure 1-14 Pin Removal 8. Pull handstrap through handstrap slot. Installation To install a new handstrap: 1. Feed bottom end of handstrap into handstrap slot on the bottom of the MC55.
Getting Started 1 - 15 Figure 1-15 Feed handstrap into Handstrap Slot 2. Slide pin into bottom of handstrap. 3. Center the pin in the handstrap loop. NOTE 4. Handstrap and pin should fit securely into the handstrap mounting area. When pulling on handstrap use enough force to engage pin into place. Pull handstrap so that the pin and bottom of handstrap slide into position in the mounting area.
1 - 16 MC55 User Guide
Chapter 2 Using the MC55 Introduction This chapter explains the buttons, status icons, and controls on the MC55, and provides basic instructions for using the MC55, including powering on and resetting the MC55, and entering and capturing data. Today Screen NOTE On devices with Windows Mobile 6.5.X, the Today screen is different. See Home Screen on page C-2 for more information. The Today screen displays important information, such as upcoming appointments and status indicators.
2-2 MC55 User Guide To customize the Today screen, tap Start > Settings > Today icon. Use the Appearance tab to customize the background and the Items tab to change the list and order of items that appear on the screen. Status Icons NOTE On devices with Windows Mobile 6.5.3, see Status Bar on page C-5 for more information. The Navigation bar at the top of the screen can contain the status icons listed in Table 2-1.
Using the MC55 2-3 Table 2-1 Status Icons (Continued) Icon Function WAN (MC5574 only) Description Call missed. Dialing while no SIM card is installed. Voice call in progress. Calls are forwarded. Call on hold. Speakerphone is on. Antenna/signal icon: wireless on/good signal. Antenna/signal icon: wireless off. Antenna/signal icon: no service or searching. GPRS in use. EGPRS in use. Roaming. SIM Card not installed. Speaker All sounds are on. All sounds are off. Battery Main battery is charging.
2-4 MC55 User Guide Table 2-2 Task Tray Icons (Continued) Icon Description Bluetooth Disabled Indicates the Bluetooth radio is off. (Available when StoneStreet One Bluetooth stack is enabled.) Bluetooth Connection Indicates the Bluetooth radio is connected to another Bluetooth device. (Available when StoneStreet One Bluetooth stack is enabled.) ActiveSync Indicates an active serial connection between the MC55 and the host computer. USB Client Mode Indicates that the MC55 is in USB Client mode.
Using the MC55 2-5 Table 2-3 Programs in the Start Menu Icon Name Description Phone Make and receive calls, switch between calls, and set up conference calling. Help See Help topics for the current screen or program. Table 2-4 lists programs that are listed in the Programs window. Table 2-4 Programs in Program Window Icon Name Description ActiveSync Synchronize information between the MC55 and a host computer or the Exchange Server.
2-6 MC55 User Guide Table 2-4 Programs in Program Window (Continued) Icon Name Description Modem Link Enables the MC55 to be used as a modem. MSP Agent Interacts with MSP agents to collect monitoring and asset information to enable the configuration, provisioning, monitoring and troubleshooting of the MC55. Refer to the Mobility Services Platform 3.2 User Guide for more information. Notes Create handwritten or typed notes, drawings, and voice recordings.
Using the MC55 2-7 Settings NOTE On devices with Windows Mobile 6.5.3, see Start Screen on page C-8 for more information. Table 2-5 lists control applications pre installed on the MC55. Tap Start > Settings to open the Settings window. Table 2-5 Settings in the Setting Window Icon Name Description Personal Tab Buttons Assign a program to a button. Input Set options for each of the input methods. Lock Set a password for the MC55. Menus Set what programs appear in the Start menu.
2-8 MC55 User Guide Table 2-5 Settings in the Setting Window (Continued) Icon Name Description Clock & Alarms Set the device clock to the date and time of your locale or to a visiting time zone when you’re traveling. Alarms can also be set at specified days and times of a week. Customer Feedback Submit feedback on the Windows Mobile 6.1 software. Encryption Allow files on a storage card to be encrypted. Encrypted files are readable only on your device.
Using the MC55 2-9 Table 2-5 Settings in the Setting Window (Continued) Icon Name Description System Info Displays the MC55’s software and hardware information. Task Manager Enables viewing of memory and CPU allocations and stops running processes. USB Config Configure the USB port. Windows Update Link to Microsoft's web site and update Windows Mobile® on your device with the latest security patches or fixes. Do not use. Obtain updates from Motorola.
2 - 10 MC55 User Guide Adjusting Volume NOTE On devices with Windows Mobile 6.5.3, see Status Bar on page C-5 for more information. To adjust the system volume using the Speaker icon in the navigation bar: 1. Tap the Speaker icon. The Volume dialog box appears. Figure 2-2 Volume Dialog Box 2. Tap and move the slide bar to adjust the volume. 3. Select the On or Off radio button to turn the volume on or off.
Using the MC55 2 - 11 The Battery icon always appears in the navigation bar when the Today screen is visible. The icon indicates the battery power level. The message displays until the Dismiss button is pressed. Figure 2-4 Battery Icon on the Title Bar Also view the battery status using the Power window. Either: • Tap the Battery icon • Tap Start > Settings > System tab > Power icon.
2 - 12 MC55 User Guide Figure 2-7 RunTime Tab 3. Select one of the Battery Reserve Options. • Option 1: Minimum - After a low battery shutdown, data will be retained for minimum amount of time. Battery should be replaced immediately to avoid data loss. • Option 2: Less - After a low battery shutdown, data will be retained for less than normal amount of time. • Option 3: Normal - After a low battery shutdown, data will be retained for maximum amount of time. 4. Tap ok.
Using the MC55 2 - 13 Figure 2-9 Main Battery Temperature Warning Dialog Box NOTE The Temperature Warning dialog box remains visible until you tap Hide. LED Indicators The MC55 has three LED indicators. The Scan/Decode LED indicates status for scanning. The Charging/Battery Status LED indicates battery charging and status.The Radio Status LED indicates WWAN radio status. Table 2-6 describes the LED indications.
2 - 14 MC55 User Guide Table 2-6 LED Indications (Continued) LED State Indication Fast Blinking Amber Charging error. Off Not charging. Single Blink Amber (when Power button pressed) Battery depleted. Blinking Amber (when Power button pressed) Battery over-temperature condition. Radio Status LED (MC5574 only) Slow Blinking Green RF (WWAN) activity. Off No RF activity. NOTE For information about scanning/decoding, see Data Capture on page 2-35.
Using the MC55 2 - 15 Waking the MC55 The wake-up conditions define what actions wake up the mobile computer after it has gone into suspend mode. The mobile computer can go into suspend mode by either pressing the Power button or automatically by Control Panel time-out settings. These settings are configurable and the factory default settings are shown in Table 2-7 are subject to change/update. Table 2-7 Wake-up Default Settings Condition for Wake-up Power Button Automatic Time-out AC power is applied.
2 - 16 MC55 User Guide Figure 2-12 Unlock Device Window Tap Unlock on the Unlock window. NOTE You can make emergency calls even when the MC55 is locked. See Making an Emergency Call on page 4-8 for more information. Password Locking Use the Password window to set a password to disable unauthorized access to the MC55. NOTE 1. If the device is configured to connect to a network, use a strong (difficult to figure out) password to help protect network security.
Using the MC55 2 - 17 a. Enter a seven character password in the Password: field. A strong password must contain at least seven characters and contain at least three of the following: uppercase and lowercase letters, numerals, and punctuation. b. Re-enter the password in the Confirm: field. 6. Tap ok. 7. To set a hint to remember the password, tap the Hint tab. Figure 2-14 Password Window - Hint Tab 8. In the text box, enter a hint for a password reminder. 9. Tap ok.
2 - 18 MC55 User Guide Keypads The MC55 offers three types of keypad configurations: Numeric, alpha-numeric and PIM. Numeric Keypad Configuration The numeric keypad contains application keys, scroll keys, and function keys. The keypad is color-coded to indicate the alternate function key (blue) values. Note that an application can change keypad functions so the MC55’s keypad may not function exactly as described.
Using the MC55 2 - 19 Table 2-8 MC55 Numeric Keypad Descriptions (Continued) Key Talk/Start Menu Description Talk (Green Phone): press to display the phone keypad window or to dial a phone number (from the phone keypad window). When on a phone call, press to place the call on hold. Use this key in conjunction with the Blue key to instantly display the Start menu from any application without tapping the screen. This function is user programmable.
2 - 20 MC55 User Guide Table 2-8 MC55 Numeric Keypad Descriptions (Continued) Key Description Soft Keys Accesses the command or menu above it on the screen. Star Produces an asterisk in default state. Press and release the orange key, then press the Star key to create special characters. See Special Character Key on page 2-31 for more information. Alphanumeric In default state, produces the numeric value on the key. In Alpha state, produces the lower case alphabetic characters on the key.
Using the MC55 2 - 21 Table 2-9 Numeric Keypad Input Modes Orange Key (Alpha Lowercase Mode) Numeric Mode Orange + Shift Keys (Alpha Uppercase Mode) Key Blue+ Key SHIFT + Key 1st Press 2nd Press 3rd Press 4th Press * 1st Press 2nd Press 3rd Press 4th Press * * * * 1 1 F1 ! * * * 2 2 F2 @ a b c A B C 3 3 F3 # d e f D E F 4 4 F4 $ g h i G H I 5 5 F5 % j k l J K L 6 6 F6 ^ m n o M N O 7 7 F7 & p q r P Q R 8 8 F8 * t u v
2 - 22 MC55 User Guide Alpha-numeric Keypad Configurations The three types of alpha-numeric keypads (QWERTY, AZERTY and QWERTZ) produce the 26-character alphabet (A-Z, both lowercase and uppercase), numbers (0-9), and assorted characters. The keypad is color-coded to indicate which modifier key to press to produce a particular character or action. The keypad default is alphabetic, producing lowercase letters.
Using the MC55 2 - 23 ok Figure 2-19 QWERTZ Keypad Configuration Table 2-10 Alpha-numeric Keypad Descriptions Key Blue Key Action Press and release the Blue key once to activate this mode temporarily, followed by another key. This displays the following icon at the bottom of the screen, until a second key is pressed: Press and release the Blue key twice to lock this mode. This displays the following icon at the bottom of the screen: Press and release the Blue key a third time to unlock.
2 - 24 MC55 User Guide Table 2-10 Alpha-numeric Keypad Descriptions (Continued) Key Talk/Start Menu Action Talk (Green Phone): press to display the phone keypad window or to dial a phone number (from the phone keypad window). When on a phone call, press to place the call on hold. Use this key in conjunction with the Blue key to instantly display the Start menu from any application without tapping the screen. This function is user programmable.
Using the MC55 2 - 25 Table 2-10 Alpha-numeric Keypad Descriptions (Continued) Key Action Soft Keys Accesses the command or menu above it on the screen. Shift Changes the state of the alpha characters from lowercase to uppercase. • Press the Shift key to activate this mode temporarily, followed by another key. This displays the following icon at the bottom of the screen, until a second key is pressed: • Press the Shift key twice to lock this mode.
2 - 26 MC55 User Guide Table 2-11 QWERTY Keypad Input Modes (Continued) Key Normal Shift + Key Orange + Key Blue + Key T t T + t Y y Y _ y U u U - u I i I = i O o O “ o P p P áü p A a A # a S s S 4 s D d D 5 d F f F 6 f G g G ( g H h H ) h J j J / j K k K : k L l L ‘ l Backspace Backspace Backspace Backspace Backspace Shift Shift Shift-Lock Shift Shift Z z Z 7 z X x X 8 x C c C 9 c V v V % v B b
Using the MC55 2 - 27 Table 2-11 QWERTY Keypad Input Modes (Continued) Key Normal Shift + Key Orange + Key Blue + Key Backlight Backlight Backlight Backlight Backlight . (Period) . > . . Note: An application can change the key functions. The keypad may not function exactly as described.
2 - 28 MC55 User Guide Table 2-12 AZERTY Keypad Input Modes (Continued) Key Normal Shift + Key Orange + Key Blue + Key V v V % v B b B & b N n N ! n M m M ? m , , < @ Enter Enter Enter Enter Enter 0 0 ) 0 0 TAB Tab Tab Back tab Tab SPACE Space Space Space Space Backlight Backlight Backlight Backlight Backlight . (Period) . > . . Note: An application can change the key functions. The keypad may not function exactly as described.
Using the MC55 2 - 29 Table 2-13 QWERTZ Keypad Input Modes (Continued) Key Normal Shift + Key Orange + Key Blue + Key H h H ) h J j J / j K k K : k L l L ‘ l Backspace Backspace Shift Shift Y y Y 7 y X x X 8 x C c C 9 c V v V % v B b B & b N n N ! n M m M ? m , , < @ , ENTER Enter ENTER ENTER Enter 0 0 ) 0 0 TAB Tab Tab Back tab Tab SPACE Space Space Space Space Backlight Backlight Backlight Backlight Backlight .
2 - 30 MC55 User Guide PIM Keypad Configuration The PIM keypad contains application keys and scroll keys. Note that an application can change keypad functions so the MC55’s keypad may not function exactly as described. See Table 2-8 for key and button descriptions and Table 2-9 on page 2-21 for the keypad’s special functions. Figure 2-20 MC55 PIM Keypad Table 2-14 MC55 PIM Keypad Descriptions Key Description Talk (Green Phone) This key is user programmable.
Using the MC55 2 - 31 Table 2-14 MC55 PIM Keypad Descriptions (Continued) Key Description Scan (yellow) Activates the scanner/imager in a scan enabled application. Scroll Up Moves up one item. Scroll Down Moves up down item. Scroll Left Moves left one item. Scroll Right Moves right one item. Soft Keys Accesses the command or menu above it on the screen. Enter Executes a selected item or function. OK Use this key as an OK or close button.
2 - 32 MC55 User Guide character, move the cursor to the right of the character then press the Orange key twice and then press the áü key until the special character replaces the original character. Table 2-15 lists the special characters you can generate. Table 2-15 Special Characters Key Special Characters Key a A c C d D e E i I l L n N o O p P r R s S t T u U y Y z Z $ / “ ( ) + ! .
Using the MC55 2 - 33 Function Buttons The MC55’s buttons perform certain functions. Scan/Action Button Volume Up/Down Button Action Button Power Button Scan/Action Button Figure 2-21 Function Buttons • Power: Press the red Power button to turn the MC55 screen on and off. The MC55 is in suspend mode when the screen is off. For more information, see Powering On the MC55 on page 1-9. Also use the Power button to reset the MC55 by performing a warm or cold boot. See Resetting the MC55 on page 2-14.
2 - 34 MC55 User Guide Entering Data When entering data on the keypad, use either the single-hand method or the two-hand method as shown in Figure 2-22.
Using the MC55 2 - 35 Data Capture The MC55 offers three types of data capture options: • Linear scanning • Imaging • Digital camera. NOTE To perform data capture a scanning enabled application must be installed on the MC55. A sample scanning application can be downloaded from the Motorola Support site at http://support.symbol.com.
2 - 36 MC55 User Guide Digital Camera MC55 with an integrated digital camera have the following features: • Omnidirectional reading of a variety of bar code symbologies, including the most popular linear, postal, PDF417, and 2D matrix code types. • Advanced intuitive aiming for easy point-and-shoot operation.
Using the MC55 2 - 37 Figure 2-23 Linear Scanning 3. Press the scan button. Ensure the red scan beam covers the entire bar code. The Scan/Decode LED lights red to indicate that scanning is in process, then lights green and a beep sounds, by default, to indicate the bar code was decoded successfully. Correct Incorrect Figure 2-24 Linear Scanner Aiming Pattern Imager Scanning 1. Ensure that a scan-enabled application is loaded on the MC55. 2. Aim the scan window at the bar code.
2 - 38 MC55 User Guide 3. Press the scan button. The red laser aiming pattern or aiming dot turns on to assist in aiming. Ensure the bar code is within the area formed by the brackets in the aiming pattern or close to the aiming dot. The aiming dot is used for increased visibility in bright lighting conditions. The Scan/Decode LED lights red to indicate that scanning is in process, then lights green and a beep sounds, by default, to indicate the bar code was decoded successfully.
Using the MC55 2 - 39 Decoded Decoded Not Decoded Not Decoded Figure 2-28 Pick List Mode with Multiple Bar Codes in Aiming Pattern 4. Release the scan button. NOTE Imager decoding usually occurs instantaneously. The MC55 repeats the steps required to take a digital picture (image) of a poor or difficult bar code as long as the scan button remains pressed. Using the RS507 Hands-free Imager An RS507 Hands-free Imager can be used with the MC55 to capture bar code data. NOTE OEM version 02.35.
2 - 40 MC55 User Guide Figure 2-29 Sample Scan Application with Preview Window 4. Move the MC55 until the red aiming reticle is over the bar code to scan. 5. The Scan/Decode LED lights green and a beep sounds, by default, to indicate the bar code was decoded successfully. NOTE The camera decode feature is set by default to automatically decode the bar code when read.
Using the MC55 2 - 41 Recording Video To record a video clip: 1. Tap Start > Programs > Pictures & Videos icon. 2. Tap Camera on the command bar. 3. Tap Menu > Video to set shooting mode to video. The available recording time displays on the screen. NOTE 4. By default, the time limit for recording videos is set to 30 seconds. Press the Enter key to begin recording. Recording stops when you press the Enter button again. Viewing Photos and Videos To view photos and video clips: 1.
2 - 42 MC55 User Guide
Chapter 3 Using GPS Navigation Introduction NOTE Only available on MC5574. The MC55 includes Global Positioning System (GPS) technology using the SiRF III chipset. GPS technology is based on a worldwide system of GPS satellites orbiting the earth that continuously transmit digital radio signals. These radio signals contain data on the satellites’ locations and their exact clock time and are used to determine your location on the earth.
3-2 MC55 User Guide 2. In the Programs tab, the GPS program port is set to None. 3. In the Hardware tab, the GPS hardware port is set to COM8. To access the GPS receiver from multiple programs simultaneously, the user can either use the Microsoft GPS API or change the GPS program port setting and access the GPS program port in the multiplexed way. Operation Acquiring satellite signals may take a few minutes. It is best to be outside and have a clear, unobstructed view of the sky.
Using GPS Navigation 3-3 ordinarily have to download from the GPS satellites. With the aGPS data, GPS receivers can operate faster and more reliably. Refer to the EMDK Help file for information on setting up SUPL on the MC55.
3-4 MC55 User Guide
Chapter 4 Using the Phone Introduction Use the MC55 to make phone calls, set up speed dials, keep track of calls, and send text messages. Your wireless service provider may also provide other services such as voice mail, call forwarding, and caller ID. Also use the integrated phone to connect to an ISP or work network in order to browse the Web and read e-mail.
4-2 MC55 User Guide To access the phone keypad tap Start > Phone, press the left soft key or press the green phone key on the MC55’s keypad. To receive calls when the MC55 is suspended, leave the phone radio turned on and ensure the MC55 is set to wake with any key. Turning the Phone On and Off NOTE On devices with Windows Mobile 6.5.3, see Status Bar on page C-5 for more information. Windows Mobile 6.
Using the Phone 4-3 Audio Modes The MC55 offers three audio modes for use during phone calls: • Handset Mode: Switches audio to the speaker at the top front of the MC55, so you can use the MC55 as a handset. This is the default mode. • Speaker Mode: Use the MC55 as a speaker phone. Tap the Speaker On button to activate this mode. Tap the Speaker Off button to switch back to handset mode. • Headset Mode: Connect a Bluetooth headset to automatically switch audio to the headset.
4-4 MC55 User Guide Figure 4-4 WWAN Bluetooth Audio Notification Dialog Box Adjusting Audio Volume Use the Volume Control Slider or the volume Up/Down buttons on the side of the MC55 to adjust the volume of the ringer when not in a call and the audio volume when in a call. Phone Volume Slider Figure 4-5 Phone Volume Slider To adjust the volume tap the Speaker icon in the Title bar. Move the slider up or down to adjust the volume. NOTE Adjust the conversation phone volume during a call.
Using the Phone 1. Tap Start > Phone or press the green phone key on the MC55’s keypad. 2. From the Phone keypad, tap the number to call. 3. Tap Talk. 4. Tap End to stop dialing or end the call. NOTE 4-5 Alternatively, use the green and red phone keys on the MC55 keypad to dial (green) and end (red) calls. If you tap a wrong number, tap Delete key to erase each subsequent digit of a number. To erase the entire number, tap and hold the Delete key.
4-6 MC55 User Guide Tap to return to the contact list (the contact is saved automatically) Scroll to see more fields Notes is a good place for maps and directions Figure 4-7 Creating a Contact 4. Using the input panel, tap in each field and enter contact information as needed. Scroll down to see all fields. 5. Tap the arrow next to the Name: or Home addr: field to open a window for adding more details. 6. To assign the contact to a category, tap Categories. 7.
Using the Phone 4-7 Creating a SIM Contact To create a SIM contact: NOTE When entering a contact phone number that contains a star (*) character followed by a plus (+) character, save the contact as an Outlook Contact. Do not save the contact to a SIM card. 1. Tap Start > Contacts. 2. Tap New. 3. Select SIM Contact. Figure 4-8 Creating a SIM Contact 4. Using the input panel, tap in each field and enter contact information. 5. When finished, tap ok to return to the contact list.
4-8 MC55 User Guide 4. Tap End or press the red phone key on the MC55 keypad to stop dialing or end the call. Making a Speed Dial Call Use Speed Dial to call someone saved in the speed dial directory. To make a speed dial call: 1. Tap Start > Phone or press the green phone key on the MC55’s keypad. 2. From the Phone keypad, tap and hold the speed dial location number assigned to a contact. (To dial a one-digit speed dial location number, tap and hold the speed dial number.
Using the Phone 4-9 Figure 4-11 Incoming Call To ignore the incoming call tap Ignore. This may send the caller to voice mail, depending on the service provider. Otherwise, this presents Busy to the calling party. To end the call tap End or press the red phone key on the MC55 keypad. Incoming Call Features • If you receive a call while in a call, tap Wait to place the call in call waiting. • You can use other programs on the MC55 during a call. To switch back to Phone, tap Talk or tap Start > Phone.
4 - 10 MC55 User Guide To find a contact name: • Enter the first letter of a contact’s first name or last name. Smart Dialing searches for the letter starting from the first character of a contact name as well as from the character that appears after a space, dash, or underscore in a contact name.
Using the Phone 4 - 11 Mute Icon Figure 4-13 Mute Button and Icon Taking Notes To create a note during a call, tap Note on the display, then enter the note. For more information about creating notes see the Windows On-Device Help. To access a note created during a call: 1. Tap Start > Phone or press the green phone key on the MC55’s keypad. 2. From the Phone keypad, tap Call History. 3. Tap and hold the number or the Note icon for the phone call entry containing the note.
4 - 12 MC55 User Guide Figure 4-15 Call History - Notes 5. Tap ok to exit. NOTE Also access notes directly from the Notes application by tapping Start > Programs > Notes. Using Speed Dial Create speed dial numbers to dial frequently called numbers with a single tap. Before creating a speed dial entry, ensure the phone number exists in Contacts. Adding a Speed Dial Entry To add a speed dial entry from the phone keypad: 1. Ensure the contact and phone number are in the Contacts list. 2.
Using the Phone 4 - 13 Figure 4-17 Speed Dial Contact Location 5. In the Location field, tap the up/down arrows to select an available location to assign as the new speed dial entry. The first speed dial location is reserved for voice mail. 6. Tap ok to add the contact to the speed dial list. Figure 4-18 Speed Dial Contact List 7. Tap ok to exit the Speed Dial Contact List. To add a speed dial entry from the Contacts window: 1. Tap Start > Contacts.
4 - 14 MC55 User Guide Figure 4-19 Contacts 2. Tap a contact name. 3. Tap Menu > Add to Speed Dial. Figure 4-20 Speed Dial Contact Location 4. Tap the up/down arrows to select an available location to assign as the new speed dial entry. The first speed dial location is reserved for voice mail. 5. Tap ok. Editing a Speed Dial Entry 1. Tap Start > Phone or press the green phone key on the MC55’s keypad. 2. Tap Speed Dial.
Using the Phone 4 - 15 Figure 4-21 Speed Dial Contact List 3. Tap and hold the contact name. 4. Tap Edit... . 5. Change the name, phone number, or location information. 6. Tap ok. NOTE Editing names and phone numbers in Speed Dial does not alter contact information in Contacts (Start > Contacts). Deleting a Speed Dial Entry 1. Tap Start > Phone or press the green phone key on the MC55’s keypad. 2. Tap Speed Dial. 3. Tap and hold the contact name. Figure 4-22 Speed Dial Delete Menu 4.
4 - 16 MC55 User Guide Using Call History Use Call History to call someone who was recently called, or recently called in. Call History provides the time and duration of all incoming, outgoing, and missed calls. It also provides a summary of total calls and easy access to notes taken during a call. Table 4-1 lists the call history icons that appear in the Call History window. Table 4-1 Call History Icons Icon Description This icon appears next to the contact information for all outgoing calls.
Using the Phone 4 - 17 2. From the Phone keypad, tap Call History. 3. Tap Menu. Figure 4-24 Call History - Tools Menu 4. Select Call Timers... . Figure 4-25 Call History - Call Timers 5. Tap Reset. (The All Calls: counter cannot be reset.) 6. Tap ok to exit the Call Timers window. Deleting Call History Items by Call Date 1. Tap Start > Phone or press the green phone key on the MC55’s keypad to display the Phone keypad. 2. From the Phone keypad, tap Call History. 3. Tap Menu > Call Timers...
4 - 18 MC55 User Guide Figure 4-26 Call History - Call Timers 4. In the Delete call history items older than: drop-down list select a time period on which to base deletion of stored items. 5. Tap ok to exit the Call Timers window. Deleting All Call History Items 1. Tap Start > Phone or press the green phone key on the MC55’s keypad to display the Phone keypad. 2. From the Phone keypad, tap Call History. 3. Tap Menu. Figure 4-27 Call History - Tools Menu 4. Select Delete all calls.
Using the Phone 4 - 19 Viewing Call Status 1. Tap Start > Phone or press the green phone key on the MC55’s keypad to display the Phone keypad. 2. From the Phone keypad, tap Call History. 3. Tap an entry. The Call Status window appears. Figure 4-29 Call History - Detail NOTE 4. When more than one call is on the phone line, only the duration of the first call is recorded. Tap ok and then ok to exit.
4 - 20 MC55 User Guide 5. Depending on the item selected, the appropriate window displays. For example, select Send Text message to display the Text Messages window. 6. Tap ok to exit the Call History window. Swapping Calls To move between two or more phone calls: 1. Tap Start > Phone or press the green phone key on the MC55’s keypad to display the Phone keypad. 2. Enter the first phone number and press Talk. When the call connects, Hold appears on the keypad. Figure 4-31 Call Swapping - Hold 3.
Using the Phone 4 - 21 Conference Calling NOTE Conference Calling and the number of conference calls allowed may not be available on all services. Please check with your service provider for Conference Calling availability. To create a conference phone session with multiple people: 1. Tap Start > Phone or press the green phone key on the MC55’s keypad to display the Phone keypad. 2. Enter the first phone number and press Talk. When the call connects, Hold appears on the keypad.
4 - 22 MC55 User Guide 10. Tap End or press the red phone key on the MC55 keypad to end the conference call. NOTE To speak privately with one party during a conference call, tap Menu > Private. To include all parties again, tap Menu > Conference. Figure 4-35 Creating a Private Call Text Messaging Use the Text Messages window to send and receive text messages to and from mobile phones. The text can contain words, numbers, or an alphanumeric combination no longer than 160 characters.
Using the Phone 4 - 23 The Caller Identification feature matches incoming text message numbers with those stored in Contacts so you know who is sending you a message. Furthermore, the New Text Message dialog box gives you the option to call the sender or save, dismiss, or delete the message. Figure 4-37 New Text Message Options When the phone function is off, you can still view received text message in Messaging: 1. Tap Start > Messaging > Text Messages, or on the Today screen, tap Text Messages.
4 - 24 MC55 User Guide 2. In the message list, tap a text message. The window displays previous text conversations. Tap to reply the message. Figure 4-40 Text Message - Conversation To reply, enter text in the reply field and tap Send. NOTE If the phone is turned off and you tried to call the sender, send a reply, or forward the message, you are prompted to turn the phone function on. Sending a Text Message To create a text message: 1.
Using the Phone 4 - 25 Address Area Message Area Figure 4-42 Create Text Message • The auto-correct feature automatically fixes common spelling errors as you type so your messages are more accurate. • The character counter lets you see and control the size of the message as you compose. • If you want to know if your text message was received, tap Menu > Message Options, then select the Request message delivery notification check box. Figure 4-43 Message Options Window 4.
4 - 26 MC55 User Guide Establishing a Data Connection NOTE Refer to the MC55 Integrator Guide for information on configuring a data connection. 5. Ensure a SIM card is installed in the MC55. 6. Configure a GPRS data connection. See MC55 Integrator Guide for more information. 7. Tap the connectivity icon or at the top of the screen. Figure 4-44 Connectivity Dialog Box 8. Tap Settings. 9. Tap Connections icon. 10. Tap Managing existing connections. 11.
Using the Phone 4 - 27 Figure 4-46 Connecting Using GPRS 13. If the SIM card is protected with a Personal Identification Number (PIN), a dialog box pops up requesting the appropriate PIN to unlock the SIM card. In this case, enter the PIN and tap ok. NOTE Place emergency calls at any time, without entering a PIN or a SIM card. 14. When a connection is established, launch Internet Explorer to browse the Internet or launch an applicable application.
4 - 28 MC55 User Guide 2. Tap Disconnect. NOTE Tapping Disconnect during an active data transfer (e.g., downloading a web page) automatically reconnects the connection. You cannot disconnect the connection until the data transfer is complete.
Chapter 5 Using Bluetooth Introduction Bluetooth-equipped devices can communicate without wires, using frequency-hopping spread spectrum (FHSS) radio frequency (RF) to transmit and receive data in the 2.4 GHz Industry Scientific and Medical (ISM) band (802.15.1). Bluetooth wireless technology is specifically designed for short-range (30 feet/10 meters) communication and low power consumption. MC55s with Bluetooth capabilities can exchange information (e.g.
5-2 MC55 User Guide The Bluetooth radio in this MC55 operates as a Class 2 device power class. The maximum output power is 2.5mW and the expected range is 32.8 feet (10 meters). A definition of ranges based on power class is difficult to obtain due to power and device differences, and whether one measures open space or closed office space. NOTE It is not recommended to perform Bluetooth wireless technology inquiry when high rate 802.11b operation is required.
Using Bluetooth 5-3 Bluetooth Configuration By default, the MC55 is configured to using the StoneStreet One Bluetooth stack. Refer to the MC55 Integrator Guide, Appendix B, for information on switching to the Microsoft Bluetooth stack. If the MC55 is configured to use the StoneStreet One Bluetooth stack, the Bluetooth icon appears at the bottom right corner of the Today screen. If the Microsoft Bluetooth stack is configured, the Bluetooth icon does not appear.
5-4 MC55 User Guide Bluetooth Power States Cold Boot Performing a cold boot on the MC55 turns off Bluetooth after initialization (which takes a few moments). It is normal to see the Bluetooth icon appear and disappear, as well as a wait cursor, when initialization proceeds in all modes. Warm Boot Performing a warm boot on the MC55 turns off Bluetooth. Suspend Suspending the MC55 turns off Bluetooth.
Using Bluetooth 5-5 Enabling Bluetooth To enable Bluetooth, tap Bluetooth icon > Enable Bluetooth. The Bluetooth icon changes to indicate that Bluetooth is enabled. Figure 5-3 Enable Bluetooth Modes The BTExplorer application has two modes for managing Bluetooth connections: Wizard Mode and Explorer Mode. The Wizard Mode is for novice Bluetooth users and the Explorer Mode is for experienced Bluetooth users. To switch between modes, select View > Wizard Mode or View > Explorer Mode.
5-6 MC55 User Guide You can also use the “tap and hold” technique to view available options. Scroll bars and view options are similar to those on the Windows desktop. The tree structure lists the following sub-items: • Local Device - This device • Remote Device - Other Bluetooth devices • Trusted Devices - Bonded (paired) Bluetooth devices • Untrusted Devices - Discovered devices that are not bonded • Favorites - Selected services that are set as Favorite for quick access.
Using Bluetooth 5-7 • Pair with a Remote Device • Active Sync via Bluetooth • Browse Files on Remote Device • Connect to Headset • Connect to Internet using Access Point • Connect to Internet using Phone/Modem • Connect to Personal Area Network • Connect to Printer • Send or Exchange Objects • Associate Serial Port • Connect to High-Quality Audio. NOTE 8. If a device discovery action has not been previously performed, a device discovery is automatically initiated.
5-8 MC55 User Guide Figure 5-7 Select Remote Device Window 9. Select a device from the list and tap Next. The MC55 searches for services on the selected Bluetooth device. Figure 5-8 Device Services NOTE If the MC55 discovers a service but the service is not supported, the service icon is grayed-out. 10. Select a service from the list and press Next. The Connection Favorite Options window appears. Figure 5-9 Connection Favorite Options Window 11.
Using Bluetooth 5-9 12. Tap Next. The Connection Summary window appears. 13. Tap Connect to add the service to the Favorite window and connect to the service. Figure 5-10 Favorites Window Available Services NOTE Some devices might not require a PIN. This depends upon the device’s authentication.
5 - 10 MC55 User Guide 2. Use the Connection Wizard to search for a Bluetooth device. 3. Select the device and tap Next. The Select Remote Service window appears. 4. Tap Next. The Connection Favorite Options window appears. 5. Tap Next. The Connection Summary window appears. 6. Tap Connect. The remote device’s accessible folders appear. Figure 5-11 File Transfer Window 7. Double-tap the file to copy. The Save Remote File window appears. Figure 5-12 Save Remote File Window 8.
Using Bluetooth 5 - 11 1. Tap and hold on the screen and select New > Folder or New > File. The Create New Folder or Create New File window appears. 2. Enter the name for the new folder or file. 3. Tap OK to create the new folder or file on the remote device. Deleting a File To delete a file from the remote device: 1. Tap and hold on the file to delete and select Delete. 2. In the Delete Remote Device File dialog box tap Yes. Getting a File To copy a file from a remote device: 1.
5 - 12 MC55 User Guide Dial-Up Networking Services Dial-up networking allows the user to connect a PC or laptop to the MC55 and use the MC55 as a modem to connect to an office network or ISP. Before setting up dial-up networking, obtain dial-up information and other necessary settings (username, password and domain name, if required) for the office network or ISP. To create a new Bluetooth connection: 1. Ensure the MC55 is discoverable and connectable. See Device Info Tab on page 5-24. 2.
Using Bluetooth 5 - 13 2. Ensure that the OBEX Object Push profile is enabled on the MC55. See Profiles Tab on page 5-35 for more information. NOTE If favorite connections have already been created, the Favorites screen displays. If no favorite connections have been created, the New Connection Wizard screen displays. 3. Use the Connection Wizard to search for a Bluetooth device. 4. Select the device and tap Next. 5. Select the OBEX Object Push service and select Connect.
5 - 14 MC55 User Guide Figure 5-15 Select Contact Entry Window 4. Select a contact to send to the other device. 5. Tap OK. 6. Tap OK to send the contact to the other device and display a confirmation dialog box on the other device to accept the contact. A Send Contact dialog appears. 7. Tap Ok. Swapping Contacts To swap contacts with another device: NOTE Prior to swapping contacts, a default contact must be set up before attempting to send a contact. Ensure that the MC55 is connectable. 1.
Using Bluetooth 5 - 15 Figure 5-17 Select Contact Entry Window 4. Select a contact to send to the other device. 5. Tap OK. 6. Tap OK to swap contacts with the other device and display a confirmation dialog box on the other device to accept the contact. 7. Tap Ok. Fetching a Contact To fetch a contact from another device: NOTE Prior to sending and receiving contacts, a default contact must be set up before attempting to send a contact. Ensure that the MC55 is connectable. 1.
5 - 16 MC55 User Guide Sending a Picture To send a picture to another device: 1. Tap and hold on OBEX Object Push and select Connect. The OBEX Object Push window appears. Figure 5-19 OBEX Object Push Window 2. In the Action: drop-down list, select Send A Picture. 3. Tap . The Send Local Picture window appears. Figure 5-20 Send Local Picture Window 4. Navigate to the picture to send to the other device. 5. Tap Open. 6.
Using Bluetooth 5 - 17 1. Ensure the MC55 is connectable (required when automatic re-connect is initiated). See Device Info Tab on page 5-24. 2. Ensure that the Headset profile is enabled on the MC55. See Profiles Tab on page 5-35 for more information. 3. Use the Connection Wizard to search for a Bluetooth headset. 4. Select the device and tap Next. 5. Select the Headset service name and select Connect. The MC55 connects to the headset.
5 - 18 MC55 User Guide Headset icon Figure 5-21 WWAN Bluetooth Audio Notification Dialog Box Serial Port Services Use the wireless Bluetooth serial port connection as you would a physical serial cable connection. Configure the application that will use the connection to the correct serial port. To establish a serial port connection: 1. Use the Connection Wizard to search for a Bluetooth serial device. 2. Select the device and tap Next. The Connection Favorite Options window appears. 3.
Using Bluetooth 5 - 19 To establish an ActiveSync connection: NOTE When creating an ActiveSync connection, only use StoneStreet One Bluetooth Explorer in Wizard mode. 1. Use the Connection Wizard to search for a Bluetooth device, such as a PC. In the drop-down list select ActiveSync via Bluetooth. 2. Select the device and tap Next. The Connection Favorite Options window appears. 3. Tap Connect. The Remote Service Connection window appears. Figure 5-23 Remote Service Connection Window 4.
5 - 20 MC55 User Guide IrMC Synchronization Services IrMC Synchronization is used to synchronize PIM contacts between a remote device and the MC55. To establish an IrMC synchronization: 1. Ensure the MC55 is connectable (required when automatic re-connect is initiated). See Device Info Tab on page 5-24. 2. Ensure that the Sync profile is enabled on the MC55. See Profiles Tab on page 5-35 for more information. 3. Tap Menu > Settings > Services tab. 4. Tap Add button. 5. Select IrMC Synchronization.
Using Bluetooth 5 - 21 14. Tap Next. 15. Tap Connect. The MC55 connects to the high-quality audio headset. For stereo headsets that can use hands-free services, connect to the hands-free service after connecting to the A2DP service: 1. Tap Menu > New Connection. 2. Select Connect to Headset from the drop-down list. 3. Tap Next. 4. Select the stereo headset and tap Next. 5. Select the Hands-Free unit service and then tap Next. 6. Tap Next. 7. Tap Connect.
5 - 22 MC55 User Guide 1. Tap the Bluetooth icon and select Show BTExplorer. The BTExplorer window appears. 2. Tap Menu > New Connection. The New Connection Wizard window appears. 3. In the drop-down list, select Pair with Remote Device. 4. Tap Next. The Select Remote Device window appears. NOTE Devices discovered previously are listed to save time. To start a new device discovery, tap and hold on the list area and select Discover Devices from the pop-up menu.
Using Bluetooth 5 - 23 Figure 5-26 Pairing Status Window 8. Tap Finish. The devices are successfully paired. The device name moves to the Trusted Devices window. Deleting a Bonded Device To delete a device no longer needed: 1. Tap the Bluetooth icon and select Show BTExplorer. The BTExplorer window appears. 2. Tap Menu > Trusted Devices. The Trusted Devices window appears. 3. Tap and hold on the device select Delete Link Key in the pop-up menu. 4. A confirmation dialog appears. Tap Yes.
5 - 24 MC55 User Guide 4. Tap OK to create the bond. The MC55 can now exchange information with the other device. Bluetooth Settings Use the BTExplorer Settings window to configure the operation of the BTExplorer application. Tap Menu > Settings. The BTExplorer Settings window appears. Device Info Tab Use the Device Info tab to configure the MC55’s Bluetooth connection modes.
Using Bluetooth 5 - 25 Figure 5-29 BTExplorer Settings - Services Tab To add a service: 1. Tap Add. The Add Local Service window displays. Figure 5-30 Add Local Service Window 2. In the list, select a service to add. 3. Tap OK. The Edit Local Service window displays for the selected service. 4. Select the appropriate information and then tap OK. See the following sections for information on the available services.
5 - 26 MC55 User Guide Figure 5-31 BTExplorer Settings - Dial-up Networking Information Table 5-4 Dial-up Networking Information Data Item Description Service Name Displays the name of the service. Service Security Select the type of security from the drop-down list. Options are None, Authenticate, or Authenticate/Encrypt. Local COM Port Select the COM port. Local Baud Rate Select the communication baud rate. Local Port Options Select the port option.
Using Bluetooth 5 - 27 Table 5-5 File Transfer Information Data Item Description Service Name Displays the name of the service. Service Security Select the type of security from the drop-down list. Options are None, Authenticate, or Authenticate/Encrypt. Root Directory Select the directory that other Bluetooth devices can access. File Permissions Select the file permissions for the selected directory. Check the appropriate box to grant read access, write access, and delete access.
5 - 28 MC55 User Guide Headset Audio Gateway Service Headset Service Audio Gateway allows connection to headset devices. Figure 5-34 BTExplorer Settings - Headset Audio Gateway Table 5-7 Headset Audio Gateway Data Item Service Name Description Lists the name of the audio service. IrMC Synchronization Service The IrMC Synchronization service used to synchronize PIM contacts between a remote device and the MC55.
Using Bluetooth 5 - 29 Table 5-8 IrMC Synchronization Data Item Description Service Name Displays the name of the service. Service Security Select the type of security from the drop-down list. Options are None, Authenticate, or Authenticate/Encrypt. Phonebook Select the Phonebook checkbox to allow synchronization with the MC55’s contacts. Select Read, Write, Create and/or Delete to allow phonebook permissions.
5 - 30 MC55 User Guide Figure 5-37 BTExplorer Settings - Personal Area Networking Table 5-10 Personal Area Networking Data Item Description Service Name Displays the name of the service. Service Security Select the type of security from the drop-down list. Options are None, Authenticate, or Authenticate/Encrypt. Support Group Ad-Hoc Networking Select to enable Ad-Hoc networking. Serial Port Service Serial port allows other Bluetooth devices to access COM ports.
Using Bluetooth 5 - 31 Table 5-11 Serial Port Services Data Item Description Service Name Displays the name of the service. Service Security Select the type of security from the drop-down list. Options are None, Authenticate, or Authenticate/Encrypt. Local COM Port Select the COM port. Local Baud Rate Select the communication baud rate. Local Port Options Select the port option.
5 - 32 MC55 User Guide Audio Video Remote Control Service Audio Video Remote Control hosts connections from Bluetooth devices supporting audio remote-control functionality. Figure 5-40 BTExplorer Settings - Audio Video Remote Control Table 5-13 Audio Video Remote Control Data Item Service Name Description Lists the name of the audio service. Security Tab Security settings allows you to set global security policies for Bluetooth.
Using Bluetooth 5 - 33 Table 5-14 Security Tab Data Item Description Use PIN Code (Incoming Connection) Select for automatic use of the PIN code entered in the PIN Code text box. It is recommended not to use this automatic PIN code feature. See Security on page 5-2 for more information. PIN Code Enter the PIN code. Encrypt Link On All Outgoing Connections Select to enable or disable encryption on all outgoing connections to other Bluetooth devices.
5 - 34 MC55 User Guide Figure 5-43 BTExplorer Settings - Virtual COM Port Tab Table 5-16 Virtual COM Port Tab Data Item Description COM5:Bluetooth Enable or disable COM Port 5. COM9:Bluetooth Enable or disable COM Port 9. COM11:Bluetooth Enable or disable COM Port 11. COM21:Bluetooth Enable or disable COM Port 21. COM22:Bluetooth Enable or disable COM Port 22. COM23:Bluetooth Enable or disable COM Port 23.
Using Bluetooth 5 - 35 Table 5-17 HID Tab Data Item Description Enable Key Repeat Enables key repeat functionality. Delay To increase key repeat delay, drag the Delay slider to the right. To decrease key repeat delay, drag the Delay slider to the left. Rate To increase key repeat speed, drag the Rate slider to the left. To decrease key repeat speed, drag the Rate slider to the right. Profiles Tab Use the Profile tab to load or remove Bluetooth services profiles.
5 - 36 MC55 User Guide System Parameters Tab Figure 5-46 BTExplorer Settings - System Parameters Tab Table 5-18 System Parameters Tab Data item Description Page Timeout Sets the amount of time the MC55 searches for a device before moving on the next device. Link Supervision Timeout Sets the amount of time that the MC55 will wait for a device to come back into range after it has gone out of range. If the device does not come back into range by the set time, the MC55 drops the connection.
Using Bluetooth 5 - 37 Table 5-19 Miscellaneous tab Data Item Description Highlight Connections Select the connection type to highlight when connected. In the Wizard Mode, the only options are Favorites or None. In the Explorer Mode the options are None, Tree View Only, List View Only, or Tree and List View. Apply Text Style Select the text style to apply to the connection text. Apply Text Color Select the text color to apply to the connection text.
5 - 38 MC55 User Guide 3. Tap ok. Disabling Bluetooth To disable Bluetooth: 1. Tap Wireless Manager and then tap the Bluetooth bar or Tap Start > Setting > Connections > Bluetooth icon > Mode tab. 2. Un-check the Turn On Bluetooth checkbox. 3. Tap ok. Discovering Bluetooth Device(s) The MC55 can receive information from discovered devices without bonding. However, once bonded, the MC55 and a bonded device exchange information automatically when you turn the Bluetooth radio on.
Using Bluetooth 5 - 39 Figure 5-50 Searching for Bluetooth Devices 6. Select a device from the list. Figure 5-51 Select a Bluetooth Device 7. Tap Next. The Enter Passcode window appears. NOTE If Smart-pairing is configured and the device is requesting one of the pre-defined PINs, the Enter Passcode window does not appear. Figure 5-52 Enter Passcode 8. Enter the Passcode on the other device. The device is added to the Bluetooth list.
5 - 40 MC55 User Guide Figure 5-53 Bluetooth Connection Confirmation You are prompted to enter a passcode. If the device has a specific passcode, enter it in the Passcode field and tap Next. If the device does not have a specific passcode, enter one in the Passcode field and tap Next. The Bluetooth radio tries to connect with the device. 9. If you created a passcode, you will be prompted by the other device to enter the same passcode. Enter the created passcode to establish a paired connection.
Using Bluetooth 5 - 41 Use the OBEX Push Service to send files and contacts to another Bluetooth device. To transfer files between the MC55 and another Bluetooth enabled device: 1. Ensure that Bluetooth is enabled and discoverable on both devices. 2. Ensure that the two devices are within 30 feet (10 meters) of one another. 3. Tap Start > Programs > File Explorer. 4. Navigate to the file to transfer. 5. Tap and hold on the filename until the pop-up menu appears.
5 - 42 MC55 User Guide 5. Tap and hold on the contact until the pop-up menu appears. Figure 5-56 Contact Window 6. Select Send Contact > Beam. The MC55 searches for Bluetooth devices in the area. 7. Tap Tap to send next to the Bluetooth device to send the file to. The MC55 communicates with the device and send the contact. When completed, Tap to send changes to Done.
Using Bluetooth 5 - 43 9. To end dial-up networking, on the MC55 tap Disconnect. Hands-free Services To connect to a Bluetooth headset: NOTE Newer Bluetooth headsets are device dependant and remember the last device they connected to. If problems occur while connecting to the headset, place the headset in discovery mode. Refer to the headset user manual for more information. Only WAN audio is routed to the headset. System audio is still emitted through the MC55 speaker.
5 - 44 MC55 User Guide 1. Ensure that Bluetooth is enabled and discoverable on both devices. 2. Ensure that the two devices are within 30 feet (10 meters) of one another. 3. Tap Start > Settings > Connections tab > Bluetooth icon > Devices tab. 4. Tap Add new device. The MC55 begins searching for discoverable Bluetooth devices in the area. 5. Select a device from the list. 6. Tap Next. The Enter Passcode window appears.
Using Bluetooth 5 - 45 5. On the Options tab, select the Turn discovery on and Allow Bluetooth devices to connect to this computer checkboxes. Figure 5-58 Computer Bluetooth Devices Window 6. On the COM Ports tab, click Add. 7. Select the Incoming (device initiates the connection) option, then click OK. Note the number of the COM port that was added. 8. Click OK. 9. Click Start > All Programs > Microsoft ActiveSync. 10. Click File > Connection Settings.
5 - 46 MC55 User Guide Synchronization is automatically initiated. The ActiveSync icon appears on the lower right corner of the Today screen. If an Authentication is required, the Enter Passcode screen appears, type an alphanumeric passkey (PIN code), then tap Next; enter the same passkey on the other device. The passkey is recommended for enhanced security. Your passkey must be between 1 to 16 alphanumeric characters. If you do not want to use a passkey, tap Next. 14.
Chapter 6 Accessories Introduction MC55 accessories, listed below, provide a variety of product support capabilities. • Four Slot Charge Only Cradle - Charges up to four MC55 devices. • Four Slot Ethernet Cradle - Charges the MC55 main battery and connects the MC55 to an Ethernet network. • Single Slot USB Cradle - Charges the MC55 main battery and a spare battery. Synchronizes the MC55 with a host computer through a USB connection.
6-2 MC55 User Guide Single Slot USB Cradle This section describes how to use a Single Slot USB cradle with the MC55. For USB communication setup procedures refer to the MC55 Integrator Guide. The Single Slot USB Cradle: • Provides 5.4 VDC power for operating the MC55. • Synchronizes information between the MC55 and a host computer. Refer to the MC55 Integrator Guide for information on setting up a partnership between the MC55 and a host computer. • Charges the MC55’s battery. • Charges a spare battery.
Accessories 6-3 Charging the Spare Battery Spare Battery Spare Battery Charging LED Figure 6-2 Spare Battery Charging Battery Charging Indicators The Single Slot USB Cradle charges the MC55’s main battery and a spare battery simultaneously. The MC55’s charge LED indicates the status of the battery charging in the MC55. See Table 1-2 on page 1-8 for charging status indications. The spare battery charging LED on the cradle indicates the status of the spare battery charging in the cradle.
6-4 MC55 User Guide To accomplish this, for small periods of time, the MC55 or accessory alternately enables and disables battery charging to keep the battery at acceptable temperatures. The MC55 or accessory indicates when charging is disabled due to abnormal temperatures via its LED. See Table 1-2 on page 1-8 and Table 6-1.
Accessories 6-5 Connection Setup AC Line Cord Ethernet Hub Power Supply USB Port Phone Port Ethernet Port Power Port Figure 6-3 Connection Setup Modem USB Ethernet Figure 6-4 Connection Switch Indicators Spare Battery Charging LED Ethernet/Modem LED Speed LED Link LED Figure 6-5 Indicators • Spare Battery Charging LED - Indicates the charging status of the spare battery. • Ethernet/Modem LED - Blink whenever Ethernet or modem connectivity is established.
6-6 MC55 User Guide • Link LED (yellow) - Blinks to indicate activity, or stays lit to indicate that a link is established. When it is not lit it indicates there is no link. Operation NOTE The CRD5500-1000XR does not support hot swapping between operational modes. After moving the switch into a different position, remove the MC55 from the cradle and then re-insert into the cradle. Ethernet Connection Place the Connection switch on the bottom of the cradle to the Ethernet position.
Accessories 6-7 Four Slot Charge Only Cradle This section describes how to set up and use a Four Slot Charge Only cradle with the MC55. The Four Slot Charge Only cradle: • Provides 5.4 VDC power for operating the MC55. • Simultaneously charges up to four MC55 devices. Charging Insert the MC55 into a slot to begin charging. Figure 6-6 MC55 Battery Charging Battery Charging Indicators The MC55’s charge LED shows the status of the battery charging in the MC55.
6-8 MC55 User Guide Four Slot Ethernet Cradle This section describes how to set up and use a Four Slot Ethernet cradle with the MC55. For cradle communication setup procedures refer to the MC55 Integrator Guide. The Four Slot Ethernet cradle: • Provides 5.4 VDC power for operating the MC55. • Connects the MC55 (up to four) to an Ethernet network. • Simultaneously charges up to four MC55 devices. Charging Insert the MC55 into a slot to begin charging.
Accessories 6-9 VCD5000 Vehicle Cradle This section describes how to use a VCD5000 vehicle cradle with the MC55. For cradle installation and communication setup procedures refer to the MC55 Integrator Guide. Once installed in a vehicle, the cradle: • holds the MC55 securely in place • provides power for operating the MC55 • re-charges the battery in the MC55. Charging the MC55 Battery Insert the MC55 into the vehicle cradle to begin charging.
6 - 10 MC55 User Guide Release Lever Figure 6-9 Removing the MC55 Battery Charging Indicators The MC55’s charge LED indicates the status of the battery charging in the MC55. See Table 1-2 on page 1-8 for charging status indications. The 2400 mAh battery fully charges in less than four hours and the 3600 mAh battery fully charges in less than six hours. Charging Temperature Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the MC55.
Accessories 6 - 11 Four Slot Battery Charger This section describes how to use the Four Slot Battery Charger to charge up to four MC55 batteries. Battery Charging 1. Connect the charger to a power source. 2. Insert the battery into a battery charging well and gently press down on the battery to ensure proper contact. Battery Battery Charging LEDs (4) Figure 6-10 Four Slot Battery Charger Battery Charging Indicators The charger has an amber LED for each battery charging well.
6 - 12 MC55 User Guide Table 6-2 Battery LED Charging Indicators (Continued) LED Indication Slow Blinking Amber Battery is charging. Solid Amber Charging complete. Fast Blinking Amber Charging error. Cables This section describes how to set up and use the cables. The cables are available with a variety of connection capabilities.
Accessories 6 - 13 Locking Tab Figure 6-11 Cable Cup Locking Tabs The MC55 amber Charge LED indicates the MC55 battery charging status. The 2400 mAh standard battery charges in less than four hours and the 3600 mAh standard battery charges in less than six hours. See Table 1-2 on page 1-8 for charging status indications. 4. When charging is complete, push the two locking tab down and remove the cable from the MC55.
6 - 14 MC55 User Guide Charging Temperature Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the MC55. To accomplish this, for small periods of time, the MC55 or accessory alternately enables and disables battery charging to keep the battery at acceptable temperatures. The MC55 or accessory indicates when charging is disabled due to abnormal temperatures via its LED. See Table 1-2 on page 1-8.
Accessories 6 - 15 • The heating and cooling cycle of a vehicle’s interior will in some cases loosen the adhesion of the suction cup. Check the vacuum seal of the vehicle mount kit for adequate adhesion each time you use the unit, and reinstall if necessary. • If the vehicle holder has problems staying on, clean the plastic suction cup with alcohol, then reinstall. Installation Install the vehicle mount on the surface of your vehicle that is reasonably flat and free of dirt and oil.
6 - 16 MC55 User Guide Locking Tab Figure 6-14 Insert MC55 into Vehicle Holder 5. Connect the auto charger cable to the MC55 and slide the two locking tabs up to secure the cable cup to the MC55. 6. Connect the other end to the cigarette lighter socket. The LED indicator on the right side of the touch screen lights up orange during charging. Flat Surface Installation 1. Remove the plastic sheet on the bottom of the mounting disc. 2. Place the disc, sticky side down, on a clean flat surface.
Accessories 6 - 17 Figure 6-16 Vehicle Holder Mounted on Flat Surface 7. Connect the auto charger cable to the MC55 and slide the two locking tabs up to secure the cable cup to the MC55. 8. Connect the other end to the cigarette lighter socket. The LED indicator on the right side of the touch screen lights up orange during charging.
6 - 18 MC55 User Guide
Chapter 7 Maintenance & Troubleshooting Introduction This chapter includes instructions on cleaning and storing the MC55, and provides troubleshooting solutions for potential problems during MC55 operation. Maintaining the MC55 For trouble-free service, observe the following tips when using the MC55: • Do not scratch the screen of the MC55. When working with the MC55, use the supplied stylus or plastic-tipped pens intended for use with a touch-sensitive screen.
7-2 MC55 User Guide • A screen protector is applied to the MC55. Motorola recommends using this to minimize wear and tear. Screen protectors enhance the usability and durability of touch screen displays. Benefits include: • Protection from scratches and gouges • Durable writing and touch surface with tactile feel • Abrasion and chemical resistance • Glare reduction • Keeping the device’s screen looking new • Quick and easy installation.
Maintenance & Troubleshooting 7-3 • To charge the mobile device battery, the battery and charger temperatures must be between +32 ºF and +104 ºF (0 ºC and +40 ºC) • Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Motorola Enterprise Mobility support.
7-4 MC55 User Guide Harmful Ingredients The following chemicals are known to damage the plastics on the MC55 and should not come in contact with the device: ammonia solutions, compounds of amines or ammonia; acetone; ketones; ethers; aromatic and chlorinated hydrocarbons; acqueous or alcoholic alkaline solutions; ethanolamine; toluene; trichloroethylene; benzene; carbolic acid and TB-lysoform. Cleaning Instructions Do not apply liquid directly to the MC55. Dampen a soft cloth or use pre-moistened wipes.
Maintenance & Troubleshooting 7-5 3. Rub the cotton portion of the cotton tipped applicator back-and-forth across the connector on the bottom of the MC55. Do not leave any cotton residue on the connector. 4. Repeat at least three times. 5. Use the cotton tipped applicator dipped in alcohol to remove any grease and dirt near the connector area. 6. Use a dry cotton tipped applicator and repeat steps 4 through 6. 7.
7-6 MC55 User Guide Troubleshooting MC55 Table 7-1 Troubleshooting the MC55 Problem Cause Solution Battery not charged. Charge or replace the battery in the MC55. Battery not installed properly. Install the battery properly. See Installing the Battery on page 1-7. System crash. Perform a warm boot. If the MC55 still does not turn on, perform a cold boot. See Resetting the MC55 on page 2-14. When pressing the power button the MC55 does not turn on but two LEDs blink.
Maintenance & Troubleshooting 7-7 Table 7-1 Troubleshooting the MC55 (Continued) Problem MC55 shuts off. Cause Solution MC55 is inactive. The MC55 turns off after a period of inactivity. If the MC55 is running on battery power, set this period from 1 to 5 minutes, in one-minute intervals. If the MC55 is running on external power, set this period to 1, 2, 5, 10, 15, or 30 minutes. Check the Power window by selecting Start > Settings > System tab and tapping the Power icon.
7-8 MC55 User Guide Table 7-1 Troubleshooting the MC55 (Continued) Problem The MC55 does not decode with reading bar code. Cause Solution Scanning application is not loaded. Load a scanning application on the MC55. See your system administrator. Unreadable bar code. Ensure the symbol is not defaced. Distance between exit window and bar code is incorrect. Place the MC55 within proper scanning range. MC55 is not programmed for the bar code.
Maintenance & Troubleshooting 7-9 Single Slot USB Cradle Table 7-3 Troubleshooting the Single Slot USB Cradle Symptom LEDs do not light when MC55 or spare battery is inserted. MC55 battery is not charging. Spare battery is not charging. During data communication, no data transmits, or transmitted data was incomplete. Possible Cause Action Cradle is not receiving power. Ensure the power cable is connected securely to both the cradle and to AC power. MC55 is not seated firmly in the cradle.
7 - 10 MC55 User Guide Four Slot Ethernet Cradle Table 7-4 Troubleshooting the Four Slot Ethernet Cradle Symptom Attempt by the MC55 to ActiveSync failed. During communication, no data transmits, or transmitted data was incomplete. Cause Solution MC55 removed from the cradle while the LED was blinking green. Wait one minute and reinsert the MC55 in the cradle. This allows the cradle to attempt another synchronization. Using an outdated version of ActiveSync. Visit http://www.microsoft.
Maintenance & Troubleshooting 7 - 11 Table 7-4 Troubleshooting the Four Slot Ethernet Cradle (Continued) Symptom Battery is not charging. Cause Solution MC55 removed from the cradle too soon. Replace the MC55 in the cradle. The 3600 mAh battery fully charges in less than six hours. Tap Start > Settings > System > Power to view battery status. Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery. MC55 is not inserted correctly in the cradle.
7 - 12 MC55 User Guide Four Slot Battery Charger r Table 7-6 Troubleshooting The Four Slot Battery Charger Symptom Possible Cause Action Battery not charging. Battery was removed from the charger or charger was unplugged from AC power too soon. Re-insert the battery in the charger or re-connect the charger’s power supply. The 3600 mAh battery fully charges in less than six hours. Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery.
Maintenance & Troubleshooting 7 - 13 Magnetic Stripe Reader Table 7-8 Troubleshooting the Magnetic Stripe Reader Symptom MSR cannot read card. MC55 battery is not charging. During data communication, no data transmits, or transmitted data was incomplete. Possible Cause Action MSR removed from MC55 during card swipe. Reattach MSR to MC55 and reswipe the card. Faulty magnetic stripe on card. See the system administrator. MSR application is not installed or configured properly.
7 - 14 MC55 User Guide
Appendix A Technical Specifications MC55 Technical Specifications The following tables summarize the EDA’s intended operating environment and technical hardware specifications. MC55 Table A-1 MC55 EDA Technical Specifications Item Description Physical Characteristics Dimensions MC5574 (3600 mAh battery): Height: 15.2 cm (6.0 in.) Width: 7.7 cm (3.03 in.) Depth: 2.7 cm (1.10 in.) MC5590 (2400 mAh battery): Height: 14.7 cm (5.78 in.) Width: 7.7 cm (3.03 in.) Depth: 2.6 cm (1.06 in.
A-2 MC55 User Guide Table A-1 MC55 EDA Technical Specifications (Continued) Item Description Display MC5574/MC5590: Transflective color 3.5” QVGA with backlight, TFT-LCD, 65K colors, 240 W x 320 H MC55A0: Pentile 3.5” VGA with backlight, TFT-LCD, 65k colors, 480 W x 640 H, 650 Nits Touch Panel Glass analog resistive touch Backlight LED backlight Battery Pack MC5574/MC5590: Rechargeable Lithium Ion 3.7V, 2400 or 3600 mAh Smart battery MC55A0: Rechargeable Lithium Ion 3.
Technical Specifications A-3 Table A-1 MC55 EDA Technical Specifications (Continued) Item Description Humidity 95% non-condensing Drop Specification MC5574/MC5590: Multiple 1.2 m (4 ft.) drops to concrete across the operating temperature range. Meets and exceeds MIL-STD 810G. MC55A0: Multiple 1.8 m (6 ft.) drops to concrete across the operating temperature range per MIL-STD 810G specifications. Tumble MC5574/MC5590: 250 0.5 m (1.6 ft.) tumbles (500 drops) MC55A0: 1000 0.5 m (1.6 ft.
A-4 MC55 User Guide Table A-1 MC55 EDA Technical Specifications (Continued) Item Description Wireless PAN Data and Voice Communications Bluetooth MC5574 and MC5590: Class II, v 2.0 EDR; on-board antenna. Supports StoneStreet One Bluetooth stack and Microsoft Bluetooth stack. MC55A0: Class II, v 2.1 EDR; on-board antenna. Supports StoneStreet One Bluetooth stack and Microsoft Bluetooth stack. Global Positioning System GPS (MC5574 only) SiRF III. on-board antenna.
Technical Specifications Table A-1 MC55 EDA Technical Specifications (Continued) Item Description Scan Angle 47° (typical) Laser Power 1.7 mW nominal 2D Imager Engine (SE4400) Specifications (MC5574 only) Field of View Horizontal - 32.2° Vertical - 24.5° Optical Resolution 640 H x 480 V pixels (gray scale) Roll 360° Pitch Angle +/- 60° from normal Skew Tolerance +/- 50° from normal Ambient Light Total darkness to 9,000 ft.
A-6 MC55 User Guide Table A-1 MC55 EDA Technical Specifications (Continued) Item Description Pitch Angle +/- 60° from normal Skew Tolerance +/- 60° from normal Ambient Light 9,000 ft. candles (96,900 Lux) Shock 2,000 +/- 5% G Aiming Element (VLD) 655 nm +/- 10 nm Illumination Element (LED) 625 nm +/- 5 nm LEDs (2x) 2D Imager Engine (SE4500-DL) Specifications (MC5590 and MC55A0 only) Field of View Horizontal - 39.2° Vertical - 25.
Technical Specifications A-7 Table A-2 Data Capture Options Item Description Laser Decode Capability Code 39 Codabar Interleaved 2 of 5 MSI UPC/EAN supplementals Webcode GS1 DataBar Truncated GS1 DataBar Expanded GS1 DataBar Stacked Omni Code 128 Code 93 Code 11 Discrete 2 of 5 EAN-8 EAN-13 UPCA UPCE Coupon Code Trioptic 39 Chinese 2 of 5 GS1 DataBar GS1 DataBar Limited GS1 DataBar Stacked GS1 DataBar Expanded Stacked Imaging Decode Capability Code 39 Code 128 Code 93 Codabar Code 11 Interleaved 2
A-8 MC55 User Guide MC55 Accessory Specifications Single Slot USB Cradle Table A-3 Single Slot USB Cradle Technical Specifications Feature Description Dimensions Height: 7.1 cm (2.80 in.) Width: 11.0 cm (4.33 in.) Depth: 15.0 cm (5.91 in.) Weight 210 g (7.
Technical Specifications Table A-4 Single Slot Ethernet/Modem/USB Cradle Technical Specifications (Continued) Feature Description Charging Temperature 0°C to 40°C (32°F to 104°F) Humidity 5% to 95% non-condensing Drop 76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature Electrostatic Discharge (ESD) +/- 15 kV air +/- 8 kV contact Four Slot Battery Charger Table A-5 Four Slot Battery Charger Technical Specifications Feature Description Dimensions Height: 4.7 cm (1.85 in.
A - 10 MC55 User Guide Table A-6 Four Slot Charge Only Cradle Technical Specifications (Continued) Feature Description Power Consumption 100 watts Operating Temperature 0°C to 50°C (32°F to 122°F) Storage Temperature -40°C to 70°C (-40°F to 158°F) Charging Temperature 0°C to 40°C (32°F to 104°F) Humidity 5% to 95% non-condensing Drop 76.2 cm (30.0 in.
Technical Specifications A - 11 Magstripe Reader Table A-8 Magstripe Reader (MSR) Technical Specifications Feature Description Dimensions 8.4 cm x 9.4 cm (3.3 inches x 3.7 inches) Weight 79.4 g (2.8 oz.) Interface Serial with baud rate up to 19,200 Format ANSI, ISO, AAMVA, CA DMV, user-configurable generic format Swipe Speed 5 to 50 in.
A - 12 MC55 User Guide Table A-9 Vehicle Cradle Technical Specifications (Continued) Feature Description Humidity 10% to 95% non-condensing Drop 76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature Electrostatic Discharge (ESD) +/- 15 kV air +/- 8 kV contact Cables Table A-10 USB Charging Cable Technical Specifications Feature Description Length 161.9 cm (63.74 in.
Technical Specifications A - 13 Table A-12 Auto Charge Cable Technical Specifications (Continued) Feature Description Storage Temperature -40°C to 70°C (-40°F to 158°F) Humidity 10% to 95% non-condensing Electrostatic Discharge (ESD) +/- 15 kV air +/- 8 kV contact Table A-13 DEX Cable Technical Specifications Feature Description Length 111.76 cm (44.0 in.
A - 14 MC55 User Guide
Appendix B Voice Quality Manager Introduction The Voice Quality Manager (VQM) is a software package that resides on the MC55. VQM enables a set of features for Voice over WiFi (VoWiFi) calls, and a sub-set of those features for cellular line calls. The VQM user interface is designed to be intuitive and easy to use, so complex tasks such as enabling the Acoustic Echo Canceller (AEC) while a call is in progress are done with very little or no user intervention.
B-2 MC55 User Guide Audio Modes The MC55 can be in any one of the seven different audio modes. The mode is visually indicated by the VQM icon on the title bar. VQM icon Figure B-1 VQM Icon in Title Bar The VQM icon indicates that the device is in speakerphone mode without Acoustic Echo Cancellation (indicated by the gray VQM icon). The audio modes and their corresponding VQM title bar icons are: Table B-1 VQM Icons Icon Description Speakerphone with Acoustic Echo Cancellation.
Using the Interfaces B-3 If the user is using a Bluetooth headset, tapping the VQM icon un-pairs the Bluetooth headset from the device causing the audio to be routed to the default mode. In VQM 2.5, there is no way to go back to the Bluetooth headset using the VQM icon if it is un-paired The only way to reconnect the Bluetooth headset to the device is by using the BTExplorer application. If the user taps the VQM icon while not on a call there is not change to the audio mode.
B-4 MC55 User Guide • Only the Avaya softphone is currently supported. Acoustic Echo Cancellation Acoustic Echo occurs during a voice call when the audio from the earpiece enters the microphone of the same device. This results in the person at the other end hearing back a delayed version of his/her own voice (“Echo”). Needless to say, “Echo” is not desirable, and needs to be suppressed. This is the functionality performed by the Acoustic Echo Canceller (AEC).
Appendix C Windows Mobile 6.5 Introduction This chapter describes the new features in the latest version of the operating system OEM version with Windows Mobile 6.5. These include: • Finger scrolling functionality • New Home screen • New Start menu • New Lock screen • RS507 support • Assisted GPS support • USB Configuration • Custom UI Settings. Finger Scrolling Windows Mobile 6.5 adds finger scrolling capabilities to the display.
C-2 MC55 User Guide Home Screen The default home screen on the MC55 is the Windows Mobile Home screen. The Home screen contains a Status Bar at the top of the screen and a Tile Bar at the bottom of the screen. The Home screen is scrollable and contains a list of application plug-ins and an Information Status bar. The Information Status bar highlights the application plug-in that is under it and provides additional information.
Windows Mobile 6.5 C-3 Figure C-3 Moving Information Status Bar Application Icon Application Information Figure C-4 Information Bar Example > Settings > Today. On the horizontal scroll, use Appearance to customize To customize the Home screen, tap the background and the Items to change the display format.
C-4 MC55 User Guide Classic Today Screen The user can change to the classic Today screen layout that is used in Windows Mobile 6.1. Status Bar Today Screen Task Tray Tile Bar Figure C-5 Classic Today Screen To change to the classic view tap > Settings > Home > Items. Figure C-6 Home Screen Settings Deselect the Windows Default checkbox and select any of the other checkboxes. Tap . The task bar at the bottom of the screen can contain the task tray icons listed in Table C-1.
Windows Mobile 6.5 C-5 Table C-1 Task Tray Icons Icon Name Description Wireless connection status Wireless connection status icon. Indicates WLAN signal strength and opens the Wireless Applications menu. Bluetooth Enabled The Bluetooth Enabled icon appears in the task tray and indicates that the Bluetooth radio is on (Displays only if the StoneStreet One Bluetooth stack is enabled).
C-6 MC55 User Guide Table C-2 Status Bar Icons Icon Description Icon Description Notifications Indicates a reminder of an upcoming calendar event. Notification that one or more instant messages were received. Notification that one or more e-mail/text messages were received. Notification that one or more voice messages were received. There are more notification icons than can be displayed. Connectivity Connection is active. Connection is not active. Synchronization is occurring.
Windows Mobile 6.5 Table C-2 Status Bar Icons (Continued) Icon Description Icon Description 3G in use. (GSM only) GPRS connecting. (GSM only) GPRS in use. (GSM only) EGPRS connecting. (GSM only) EGPRS in use. (GSM only) EVDO connecting. (CDMA only) EVDO in use. (CDMA only) SIM Card not installed. (GSM only) All sounds are on. All sounds are off. Audio Vibrate is on. Battery Battery is charging. Battery has a full charge. Battery has a high charge. Battery has a medium charge.
C-8 MC55 User Guide Table C-3 Task Tray Icons Icon Name Description Magnify Enlarges the screen. Connectivity Displays the Connectivity dialog box. Phone Displays the Phone dialog box. Volume Displays the Volume dialog box. Power Displays the Power window. Clock & Alarms Opens the Clocks & Alarms window. Tile Bar The Tile Bar, located at the bottom of the screen, contains the Start tile displays tiles that vary depending upon the open application. to open the Start Menu.
Windows Mobile 6.5 C-9 Table C-4 Programs on the Start Screen Icon Name Description Icon Name Description Home Displays the Home screen. Text Send an SMS text message. Phone Make calls. E-mail Send an Email. Contacts Keep track of friends and colleagues. Settings Open the Settings folder. Table C-4 lists the default icons available on the Settings folder. Internet Explorer Browse Web and WAP sites as well as download new programs and files from the Internet.
C - 10 MC55 User Guide Table C-4 Programs on the Start Screen Icon Name Description Icon Name Description Office Mobile Use the complete suite of Microsoft® Office applications for your mobile device. Internet Sharing Connect a notebook computer to the Internet using the MC55's data connection. File Explorer Organize and manage files on your device. Task Manager Enables viewing of memory and CPU allocations and stops running processes.
Windows Mobile 6.5 C - 11 Table C-4 Programs on the Start Screen Icon Name Description Icon Name Description MSP Agent Enables management of the MC55 from an MSP Server. Requires the purchase of an appropriate MSP client license per device to suit the level of management functionality required. SIM Toolkit Manage the contacts that are stored on your SIM card. Copy SIM contents to Contacts on the MC55.
C - 12 MC55 User Guide Table C-5 Setting Applications (Continued) Icon Name Power Description Icon Name Description Check battery power and set the time-out for turning off the display to conserve battery power. Connections Folder Beam Set the MC55 to receive incoming IrDA beams. Not supported on MC55.
Windows Mobile 6.5 C - 13 Table C-5 Setting Applications (Continued) Icon Name Description Icon Name Description Error Reporting Enable or disable the Microsoft’s error reporting function. Encryption Allow files on a storage card to be encrypted. Encrypted files are readable only on your device. External GPS Set the appropriate GPS communication ports, if required. Refer to MC55 GPS Setup on page 3-1. GPS Setup View GPS SUPL information.
C - 14 MC55 User Guide Speaker Icon You can adjust the system volume using the Speaker icon. 1. Tap the Status Bar and then tap the Speaker icon. The Volume dialog box appears. Figure C-10 Volume Dialog Box 2. Tap and move the slide bar to adjust the volume. 3. Select the On or Off radio button to turn the volume on or off. NOTE Use can also adjust the system volume using the Sounds & Notifications window or by using the keypad.
Windows Mobile 6.5 C - 15 Figure C-12 Connectivity Dialog Box Locking the MC55 You can lock the MC55 by disabling key presses and screen tap or by requiring a password. NOTE You can make emergency calls even when the MC55 is locked. Locking the MC55 turns off keyboard and touch screen functionality. This is helpful when the MC55 is turned on and you want to prevent accidental key presses. To lock the device, tap > . Locking without PIN or Password When the MC55 is locked, the Lock screen appears.
C - 16 MC55 User Guide Locking with Simple PIN When the MC55 is locked, the Lock screen appears. MC5574 MC5590/MC55A0 Figure C-14 Simple PIN Lock Screen On the MC5574, drag to either the right or left side of the screen. Enter the PIN and then tap the Contacts window, tap to unlock and display the Home screen, tap to unlock and display the Messaging window. Figure C-15 Simple PIN Password Window On the MC5590, enter the PIN and then tap Unlock.
Windows Mobile 6.5 C - 17 Figure C-16 Strong Password Lock Screen Enter the strong password and then tap Unlock. Password Locking Setup Use the Password window to set a password to disable unauthorized access to the MC55. NOTE 1. Tap If the device is configured to connect to a network, use a strong (difficult to figure out) password to help protect network security. Password cracking tools continue to improve and the computers used to crack passwords are more powerful than ever.
C - 18 MC55 User Guide a. Enter a seven character password in the Password: field. A strong password must contain at least seven characters and contain at least three of the following: uppercase and lowercase letters, numerals, and punctuation. b. Re-enter the password in the Confirm: field. 6. Tap 7. In the horizontal scroll, select Hint. Enter a hint to remember the password if you forget it. 8. Tap 9. In the text box, enter a hint for a password reminder. 10. Tap . . .
Windows Mobile 6.5 C - 19 Figure C-18 SUPL Setup Tab 2. Select Enable SET Initiated SUPL on Opening to enable the MC55 to initiate SUPL upon opening the GPS port. 3. Select Enable Network Initiated SUPL to enable the network to initiate SUPL. 4. Select Generate Server IP from IMSI to automatically generate the server IP address from the IMSI (on GSM WAN devices only) or select Using Motorola Server to use the Motorola SUPL server. 5. Enter the SUPL Server IP address in the Server IP field.
C - 20 MC55 User Guide Smart Re-Aiding causes the MC55 to reconnect to the SUPL server and download new A-GPS data if there are satellites in view and the number of satellites in use fall below the SVLimit value and the length of time passed since the lfCast SUPL session is more than the value set in the Interval field. Timing Control on Opening determines whether a SUPL session is established when the GPS port is opened.
Windows Mobile 6.5 C - 21 1. Tap Start > Settings > > System > UI Settings. 2. Tap the IE Zoom Mapping tab. Figure C-21 IE Zoom Mapping Tab 3. Select Off. 4. Tap OK. 5. Tap OK to turn off mapping.
C - 22 MC55 User Guide
Glossary A API. (Application Programming Interface) An interface by means of which one software component communicates with or controls another. Usually used to refer to services provided by one software component to another, usually via software interrupts or function calls AZERTY. A standard keyboard commonly used on French keyboards. “AZERTY” refers to the arrangement of keys on the top row of keys. AKU. (Adaptation Kit Update) Updates to the Windows Mobile operating system. AFH.
Glossary - 2 MC55 User Guide bps. See Bits Per Second. Byte. On an addressable boundary, eight adjacent binary digits (0 and 1) combined in a pattern to represent a specific character or numeric value. Bits are numbered from the right, 0 through 7, with bit 0 the low-order bit. One byte in memory is used to store one ASCII character. C CDRH. Center for Devices and Radiological Health. A federal agency responsible for regulating laser product safety.
Glossary - 3 Decode Algorithm. A decoding scheme that converts pulse widths into data representation of the letters or numbers encoded within a bar code symbol. Decryption. Decryption is the decoding and unscrambling of received encrypted data. Also see, Encryption and Key. Depth of Field. The range between minimum and maximum distances at which a scanner can read a symbol with a certain minimum element width. Device Configuration Package.
Glossary - 4 MC55 User Guide H Hard Reset. See Cold Boot. Hz. Hertz; A unit of frequency equal to one cycle per second. Host Computer. A computer that serves other terminals in a network, providing such services as computation, database access, supervisory programs and network control. I IEC. International Electrotechnical Commission. This international agency regulates laser safety by specifying various laser operation classes based on power output during operation. IEC (825) Class 1.
Glossary - 5 K Key. A key is the specific code used by the algorithm to encrypt or decrypt the data. Also see, Encryption and Decrypting. L LASER. Light Amplification by Stimulated Emission of Radiation.The laser is an intense light source. Light from a laser is all the same frequency, unlike the output of an incandescent bulb. Laser light is typically coherent and has a high energy density. laser scanner. A type of bar code reader that uses a beam of laser light. LCD. See Liquid Crystal Display.
Glossary - 6 MC55 User Guide NVM. Non-Volatile Memory. O Open System Authentication. Open System authentication is a null authentication algorithm. P PAN . Personal Area Network. Using Bluetooth wireless technology, PANs enable devices to communicate wirelessly. Generally, a wireless PAN consists of a dynamic group of less than 255 devices that communicate within about a 33-foot range. Only devices within this limited area typically participate in the network. PING.
Glossary - 7 SDK. Software Development Kit Shared Key. Shared Key authentication is an algorithm where both the AP and the MU share an authentication key. SID. System Identification code. An identifier issued by the FCC for each market. It is also broadcast by the cellular carriers to allow cellular devices to distinguish between the home and roaming service. Soft Reset. See Warm Boot. Space. The lighter element of a bar code formed by the background between bars. Specular Reflection.
Glossary - 8 MC55 User Guide Terminal. See Mobile Computer. Terminal Emulation. A “terminal emulation” emulates a character-based mainframe session on a remote non-mainframe terminal, including all display features, commands and function keys. The VC5000 Series supports Terminal Emulations in 3270, 5250 and VT220. TFTP. (Trivial File Transfer Protocol) A version of the TCP/IP FTP (File Transfer Protocol) protocol that has no directory or password capability.
Index Numerics 1-D bar codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35 2-D bar codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35 A accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 auto charge cable . . . . . . . . . . . . . . . . . . . . . . . . 1-3 cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12 charge only cable . . . . . . . . . . . . . . . . . . . . . . . .
Index - 2 MC55 User Guide adaptive frequency hopping . . . . . . . . . . . . . . . . 5-1 bonding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21 deleting bonded device . . . . . . . . . . . . . . . . . . . 5-23 security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 turning off . . . . . . . . . . . . . . . . . . . . . . . . . .5-4, 5-38 turning on . . . . . . . . . . . . . . . . . . . . . . . . . .5-5, 5-37 bluetooth communicating icon . . . . . . . . . . . . . . .
Index - 3 F fabric holster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 file explorer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-10 Four Slot Battery Charger . . . . . . . . . . . . . . . . . . . . . 6-1 four slot charge only cradle . . . . . . . . . . . . . . . . . . . . 6-7 charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 charging indicators . . . . . . . . . . . . . . . . . . . . . . . 6-7 four slot Ethernet cradle . . . . . . . . . . .
Index - 4 MC55 User Guide notational conventions . . . . . . . . . . . . . . . . . . . . . . . . xvii notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-9 notes application . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 numeric keypad . . . . . . . . . . . . . . . . . . . . . . . .2-18, 2-30 input modes . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21 key descriptions . . . . . . . . . . . . . . . . . . . .2-18, 2-30 O operating environment . . . . . .
Index - 5 charging indicators . . . . . . . . . . . . . . . . . . . . . . 6-11 setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11 speaker icon . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3, 2-10 speaker mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 special character key . . . . . . . . . . . . . . . . . . . . . . . . 2-31 speed dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8, 4-12 spring loaded stylus . . . . . . . . . . . . . .
Index - 6 MC55 User Guide
Motorola, Inc. One Motorola Plaza Holtsville, New York 11742, USA 1-800-927-9626 http://www.motorola.com/enterprisemobility MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2010 Motorola, Inc. All rights reserved.
