MC75 Enterprise Digital Assistant User Guide
MC75 Enterprise Digital Assistant User Guide 72E-103077-04 Rev.
ii MC75 User Guide © 2008-10 by Motorola, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis.
iii Revision History Changes to the original manual are listed below: Change Date Description -01 Rev. A 6/10/08 Initial release. -02 Rev. A 08/14/08 Add re-boot after installing SIM card. Add dual line SIM support. -03 Rev. A 03/09/10 Add OEM Version 02.35.000 and 02.35.001support. Add DSD keypad. -04 Rev. A 10/22/10 Add OENM Version 03.38.xxx support.
iv MC75 User Guide
Table of Contents Revision History .................................................................................................................................... ii About This Guide Introduction ........................................................................................................................................... Documentation Set Configurations.......................................................................................................................................
vi MC75 User Guide Turning Off the Radios ................................................................................................................... 1-13 Chapter 2: Using the MC75 Introduction .......................................................................................................................................... Today Screen ...................................................................................................................................... Status Icons .......
Table of Contents Adaptive Frequency Hopping .............................................................................................................. Security ................................................................................................................................................ Disabling Bluetooth ........................................................................................................................ Enabling Bluetooth .........................................
viii MC75 User Guide System Parameters Tab ................................................................................................................ 4-33 Miscellaneous Tab ......................................................................................................................... 4-33 Chapter 5: Using the Phone Introduction ..........................................................................................................................................
Table of Contents Charging Temperature ............................................................................................................. Four Slot Ethernet Cradle .................................................................................................................... Charging ........................................................................................................................................ Battery Charging Indicators .............................................
x MC75 User Guide Cleaning Cradle Connectors .......................................................................................................... Cleaning Frequency ....................................................................................................................... Troubleshooting ................................................................................................................................... MC75 ..................................................................
Table of Contents Password Locking Setup ............................................................................................................... Using the RS507 Hands-free Imager ................................................................................................... Removing the Battery .......................................................................................................................... Battery Removal ................................................................
xii MC75 User Guide
About This Guide Introduction This guide provides information about using the MC75 Enterprise Digital Assistant (EDA) and accessories. NOTE Screens and windows pictured in this guide are samples and can differ from actual screens. For configurations with OEM version 03.38.000X and Windows Mobile 6.5 operating system, refer to Appendix C, Windows Mobile 6.5 for more information about new features.
xiv MC75 User Guide Configurations This guide covers the following configurations: Configuration Radios Display Memory Data Capture Operating System Keypads MC7506 WPAN: Bluetooth WWAN: HSDPA GPS: SiRF III 3.5” VGA Color 128 MB RAM/ 256 MB Flash 1D laser scanner, 2D imager Windows Mobile 6.X Professional Numeric, QWERTY, AZERTY or QWERTZ keypad MC7508 WPAN: Bluetooth WWAN: EVDO GPS: SiRF III 3.5” VGA Color 128 MB RAM/ 256 MB Flash 1D laser scanner, 2D imager Windows Mobile 6.
About This Guide The second line lists the operating system version and the build number. The last part of the build number represents the AKU number. For example, Build 18552.0.7.5 indicates that the device is running AKU version 0.7.5. OEM Version To determine the OEM software version: Tap Start > Settings > System tab > System Info icon > System tab. BTExplorer Software To determine the BTExplorer software version:. NOTE For configurations with Windows Mobile 6.
xvi MC75 User Guide Fusion Software To determine the Fusion software version: Tap Signal Strength icon > Wireless Status > Versions. Signal Strength icon Phone Software To determine the Phone software version: Tap Start > Phone > Menu > Options > Phone Info or Version Information tab.
About This Guide MC7506/96 MC7508/98 Chapter Descriptions Topics covered in this guide are as follows: • Chapter 1, Getting Started provides information on getting the MC75 up and running for the first time. • Chapter 2, Using the MC75 provides basic instructions for using the MC75, including powering on and resetting the MC75, and entering and capturing data. • Chapter 3, Using GPS Navigation provides information about GPS navigation with the MC75.
xviii MC75 User Guide • Bold text is used to highlight the following: • Dialog box, window, and screen names • Drop-down list and list box names • Check box and radio button names • Key names on a keypad • Button names on a screen. • bullets (•) indicate: • Action items • Lists of alternatives • Lists of required steps that are not necessarily sequential • Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.
About This Guide xix If you purchased your Enterprise Mobility business product from a Motorola business partner, contact that business partner for support.
xx MC75 User Guide
Chapter 1 Getting Started Introduction This chapter lists the parts and accessories for the MC75 and explains how to install and charge the batteries, replace the strap, and power on the MC75 for the first time.
1-2 MC75 User Guide Battery Cover Handstrap Handstrap Slot Battery Cover Latch Headset Jack Camera Flash IrDA Window Camera Memory Card Cover Speaker Action Button Scan Window (Imager Configuration Shown) Scan/Action Button Stylus Tether Point Figure 1-2 MC75 Rear View Unpacking Carefully remove all protective material from the MC75 and save the shipping container for later storage and shipping.
Getting Started 1-3 Accessories Table 1-1 lists the accessories available for the MC75. Table 1-1 MC75 Accessories Accessory Part Number Description Cradles Single Slot USB/Serial Cradle CRD7X00-1000RR Charges the MC75 main battery and a spare battery. Synchronizes the MC75 with a host computer through a USB connection. Four Slot Ethernet Cradle CRD7000-4000ER Charges the MC75 main battery and connects the MC75 with an Ethernet network.
1-4 MC75 User Guide Table 1-1 MC75 Accessories (Continued) Accessory Part Number Description Biometric Attachment MC7XFPR-01R Contains a finger print reader. Biometric Attachment MC7XFPSCR-01R Contains a finger print reader, a contact smart card reader and a contactless smart card reader. Modem Dongle MDM9000-100R Provides modem connectivity. Spare 3600 mAh lithium-ion battery BTRY-MC7XEAB00 Replacement 3600 mAh battery.
Getting Started 1-5 • Mobile phone service provider account details. • Information regarding service access and preferences. • Contact information, which can be moved to Contacts on the MC75. • Any additional services to which you have subscribed. NOTE For more information about SIM cards, refer to the service provider's documentation. To install the SIM card: 1. Lift the SIM cover using the stylus tip. Figure 1-3 Lifting the SIM Cover 2.
1-6 MC75 User Guide d. Press the red Power button to suspend the MC75. e. Perform a warm boot. See Resetting the MC75 on page 2-15. f. Make a call to verify cellular connection. NOTE For detailed information about WWAN activation and settings, refer to the MC75 Integrator Guide. Installing the Main Battery NOTE The MC75 ships with a 3600 mAh battery. An optional 4800 mAh battery is available. To install the main battery: 1.
Getting Started 1-7 Handstrap Handstrap Slot Figure 1-6 Inserting the Handstrap The MC75 powers up after inserting the battery and replacing the battery cover. Charging the Battery CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 7-2.
1-8 MC75 User Guide The 3600 mAh battery fully charges in approximately five hours and the 4800 mAh battery charges in approximately seven hours. Table 1-2 LED Charge Indicators Charging/Battery Status LED Indication Off MC75 is not charging. MC75 is not inserted correctly in the cradle or connected to a power source. Charger/cradle is not powered. Slow Blinking Amber (1 blink every 2 seconds) MC75 is charging. Solid Amber Charging complete.
Getting Started 1. Remove the stylus from its holder on the back of the MC75. 2. Carefully press and briefly hold the tip of stylus on the center of each target that appears on the screen. 3. Repeat as the target moves around the screen, then tap the screen to continue. 1-9 Checking Battery Status To check the charge status of the main battery or backup battery in the MC75, tap Start > Settings > System tab > Power icon to display the Power window.
1 - 10 MC75 User Guide Figure 1-8 Card Removal 3. Carefully press and release the card to eject it. 4. Remove the card from the card slot. 5. Replace the memory card cover and tighten the screws. Adjusting the Handstrap The MC75 handstrap is attached to the bottom of the battery cover. Adjust the handstrap to increase comfort when holding the MC75 for extended periods of time. To adjust the handstrap: 1. Feed the handstrap through the handstrap slot in either direction, to tighten or loosen. 2.
Getting Started 1 - 11 Lift Screen Protector Corner Figure 1-10 Removing the Screen Protector CAUTION NOTE Do not use a sharp object to remove the protector. Doing so can damage the display. Not using a screen protector can affect warranty coverage. To purchase replacement protectors, contact your local account manager or Motorola, Inc. These include screen protector installation instructions. Part number: KT-67525-01R Screen Protector 3/pk. Replacing the Main Battery 1.
1 - 12 MC75 User Guide 8. With the battery cover latches open, insert the cover, bottom first, then press down on the top of the cover. 9. Close the battery cover latches on either side of the battery cover. 10. Insert the handstrap through the handstrap slot, then tighten and press down to secure. The MC75 powers up after inserting the battery and replacing the battery cover.
Getting Started 1 - 13 2. Select the On battery power: Disable keylight if device if not used for check box and select a value from the drop-down list. 3. Select the Advanced tab. 4. Tap the Disable keylight check box to turn off the keypad backlight. 5. Select ok. Turning Off the Radios NOTE On devices with Windows Mobile 6.5.3, see Status Bar on page C-5 for more information.
1 - 14 MC75 User Guide Figure 1-13 Wireless Manager Window NOTE Wireless connection options vary depending upon configurations. To enable or disable a wireless connection, tap the specific button. To enable or disable all wireless connections, tap the All button. To configure settings for a connection, tap Menu.
Chapter 2 Using the MC75 Introduction This chapter explains the buttons, status icons, and controls on the MC75, and provides basic instructions for using the MC75, including powering on and resetting the MC75, and entering and capturing data. The MC75 factory default radio states are: • Bluetooth - OFF • Phone - ON • Wireless LAN - ON.
2-2 MC75 User Guide Today Screen NOTE On devices with Windows Mobile 6.5.3, the Today screen is different. See Home Screen on page C-1 for more information. The Today screen displays important information, such as upcoming appointments and status indicators. Tap a section on the screen to open the associated program. Alternatively, tap Start > Today to display the Today screen.
Using the MC75 Table 2-1 Status Icons (Continued) Icon Function Connectivity Description Connection is active. Connection is not active. Synchronization is occurring. Wi-Fi available. Wi-Fi in use. HSDPA available. (MC7506 and MC7596) 3G available. (MC7506 and MC7596) GPRS available. (MC7506 and MC7596) EGPRS available. (MC7506 and MC7596) 1xRTT available. (MC7508 and MC7598) EVDO Rev. 0 available. (MC7508 and MC7598) EVDO Rev. A available.
2-4 MC75 User Guide Table 2-1 Status Icons (Continued) Icon Function WAN Description Call missed. Dialing while no SIM card is installed. Voice call in progress. Calls are forwarded. Call on hold. Speakerphone is on. Antenna/signal icon: wireless on/good signal. Antenna/signal icon: wireless off. Antenna/signal icon: no service or searching. HSDPA connecting. (MC7506 and MC7596) HSDPA in use. (MC7506 and MC7596) 3G connecting. (MC7506 and MC7596) 3G in use. (MC7506 and MC7596) GPRS connecting.
Using the MC75 2-5 The command bar at the bottom of the screen can contain the task tray icons listed in Table 2-2. Table 2-2 Task Tray Icons Icon Description Wireless connection status Indicates WLAN signal strength. Bluetooth Enabled Bluetooth radio is on. Bluetooth Disabled Bluetooth radio is off. Bluetooth Connection Bluetooth radio is connected to another Bluetooth device. ActiveSync Active serial connection between the MC75 and the host computer.
2-6 MC75 User Guide Table 2-3 Programs in the Start Menu Icon Name Description Messaging Send and receive e-mail, and text messages. Phone Make and receive calls, switch between calls, and set up conference calling. Help See Help topics for the current screen or program. Table 2-4 lists programs that are listed in the Programs window. Table 2-4 Programs in Program Window Icon Name Description ActiveSync Synchronize information between the MC75 and a host computer or the Exchange Server.
Using the MC75 2-7 Table 2-4 Programs in Program Window (Continued) Icon Name Description Messenger Use this mobile version of Windows Live Messenger. Modem Link Enables the MC75 to be used as a modem. MSP Agent Interacts with MSP agents to collect monitoring and asset information to enable the configuration, provisioning, monitoring and troubleshooting of the MC75. Refer to the MC75 Integrator Guide for more information. Notes Create handwritten or typed notes, drawings, and voice recordings.
2-8 MC75 User Guide Settings NOTE On devices with Windows Mobile 6.5.3, see Start Screen on page C-8 for more information. Table 2-5 lists control applications pre installed on the MC75. Tap Start > Settings to open the Settings window. Table 2-5 Settings in the Setting Window Icon Name Description Personal Tab Buttons Assign a program to a button. Input Set options for each of the input methods. Lock Set a password for the MC75. Menus Set what programs appear in the Start menu.
Using the MC75 2-9 Table 2-5 Settings in the Setting Window (Continued) Icon Name Description Clock & Alarms Set the device clock to the date and time of your locale or to a visiting time zone when you’re traveling. Alarms can also be set at specified days and times of a week. Customer Feedback Submit feedback on the Windows Mobile 6 software. Encryption Allow files on a storage card to be encrypted. Encrypted files are readable only on your device.
2 - 10 MC75 User Guide Table 2-5 Settings in the Setting Window (Continued) Icon Name Description System Info Displays the MC75’s software and hardware information. Task Manager Enables viewing of memory and CPU allocations and stops running processes. Refer to the Microsoft Applications for Windows Mobile 6 User Guide for more information. Trigger Settings Enables the MC75 to be used with the TRG7000 Trigger Handle. USB Config Configures the USB port.
Using the MC75 2 - 11 Adjusting Volume NOTE On devices with Windows Mobile 6.5.3, see Status Bar on page C-5 for more information. To adjust the system volume using the Speaker icon in the navigation bar: 1. Tap the Speaker icon. The Volume dialog box appears. Figure 2-2 Volume Dialog Box 2. Tap and move the slide bar to adjust the volume. 3. Select the On or Off radio button to turn the volume on or off.
2 - 12 MC75 User Guide The Battery icon always appears in the navigation bar when the Today screen is visible. The icon indicates the battery power level. The message displays until the Dismiss button is pressed. Figure 2-4 Battery Icon on the Title Bar Also view the battery status using the Power window. Battery Reserve Options If the charge of the battery reaches a critical threshold, the MC75 shuts down. This threshold can be changed but affects the amount of time that data can be retained. 1.
Using the MC75 2 - 13 • Option 3: Normal - After a low battery shutdown, data will be retained for maximum amount of time. 4. Tap ok. Main Battery Temperature Notifications The temperature notification system implements three levels of notification when the temperature within the battery exceeds specific temperature thresholds: • Level 1: Temperature Watch; this level is similar to main battery low warning. It indicates that the battery temperature has reached the first threshold level.
2 - 14 MC75 User Guide LED Indicators The MC75 has three LED indicators. The Scan/Decode LED indicates status for bar code scanning. The Charging/Battery Status LED indicates battery charging and status. The Radio Status LED indicates WAN radio status. Table 2-6 describes the LED indications. Scan/Decode Charging/Battery Radio Status LED Status LED LED Figure 2-9 LED Indicators Table 2-6 LED Indications LED State Indication Scan/Decode LED Solid Green Successful decode/capture.
Using the MC75 2 - 15 Resetting the MC75 There are two reset functions, warm boot and cold boot. A warm boot restarts the MC75 by closing all running programs. A cold boot also restarts the MC75, and also resets the clock. Data saved in flash memory or a memory card is not lost. If the MC75 is not functioning properly, perform a warm boot first. If the MC75 still does not respond, perform a cold boot. Performing a Warm Boot Hold down the Power button for approximately five seconds.
2 - 16 MC75 User Guide Locking the MC75 NOTE On devices with Windows Mobile 6.5.3, see Locking the MC75 on page C-15 for more information. Use the Device Lock feature to prevent use of the device. Note that when locked, the MC75 does not respond to screen or keypad input. To lock the device, tap the Device unlocked icon. The icon changes to locked. Device Unlocked Icon Device Locked Icon Figure 2-10 Device Locked/Unlocked Icons To unlock the device and free it for use, tap Unlock.
Using the MC75 2 - 17 Keypads The MC75 offers two types modular keypad configurations: Numeric and alpha-numeric. Numeric Keypad Configuration The numeric keypad contains application keys, scroll keys, and function keys. The keypad is color-coded to indicate the alternate function key (blue) values. Note that an application can change keypad functions so the MC75’s keypad may not function exactly as described.
2 - 18 MC75 User Guide Table 2-8 MC75 Numeric Keypad Descriptions (Continued) Key Description Talk/End Talk (Green Phone): press to display the phone keypad window or to dial a phone number (from the phone keypad window). End (Red Phone): press when the phone keypad window displays to stop dialing or end a call. Scan (yellow) Activates the scanner/imager in a scan enabled application. Scroll Up and Down Moves up one item. Moves left one item when pressed with the Orange key.
Using the MC75 2 - 19 Table 2-8 MC75 Numeric Keypad Descriptions (Continued) Key Description SHIFT Press and release the SHIFT key to activate the keypad alternate SHIFT functions. A single press displays the following icon at the bottom of the screen, until a second key is pressed: Press the Orange key, then the Shift key to add a temporary shift (that applies only to the next key pressed) to the orange lock state.
2 - 20 MC75 User Guide Table 2-9 Numeric Keypad Input Modes (Continued) Orange Key (Alpha Lowercase Mode) Numeric Mode Orange + Shift Keys (Alpha Uppercase Mode) Key Blue+ Key SHIFT + Key 1st Press 2nd Press 3rd Press 4th Press 1st Press Up Up Up Hilight Up Left Left Down Down Down Hilight Down Right Right Enter Action Action Action Action Action 2nd Press 3rd Press Note: An application can change the key functions. The keypad may not function exactly as described.
Using the MC75 2 - 21 DSD Keypad Configuration The DSD keypad contains application keys, scroll keys, and function keys. The keypad is color-coded to indicate the alternate function key (blue) values. Note that an application can change keypad functions so the MC75’s keypad may not function exactly as described. See Table 2-10 for key and button descriptions and Table 2-11 on page 2-23 for the keypad’s special functions.
2 - 22 MC75 User Guide Table 2-10 MC75 DSD Keypad Descriptions (Continued) Key Description Scroll Up Moves up one item. Scroll Left Moves left one item. Scroll Down Moves down one item. Scroll Right Moves right one item. Alphanumeric In default state, produces the numeric value on the key. In Alpha state, produces the lower case alphabetic characters on the key. Each key press produces the next alphabetic character in sequence.
Using the MC75 2 - 23 Table 2-11 DSD Keypad Input Modes Orange Key (Alpha Lowercase Mode) Numeric Mode Orange + Shift Keys (Alpha Uppercase Mode) Key Blue+ Key SHIFT + Key 1st Press 2nd Press 3rd Press 4th Press * 1st Press 2nd Press 3rd Press 4th Press * * * * 1 1 F1 ! * * * 2 2 F2 @ a b c A B C 3 3 F3 # d e f D E F 4 4 F4 $ g h i G H I 5 5 F5 % j k l J K L 6 6 F6 ^ m n o M N O 7 7 F7 & p q r P Q R 8 8 F8 * t u v T
2 - 24 MC75 User Guide Alpha-numeric Keypad Configurations The three types of alpha-numeric keypads produce the 26-character alphabet (A-Z, both lowercase and uppercase), numbers (0-9), and assorted characters. The keypad is color-coded to indicate which modifier key to press to produce a particular character or action. The keypad default is alphabetic, producing lowercase letters. See Table 2-12 for key and button descriptions and Table 2-13 on page 2-27 for the keypad’s special functions.
Using the MC75 2 - 25 Table 2-12 Alpha-numeric Keypad Descriptions Key Blue Key Action Launches applications (shown on the keypad in blue). Press the Blue key once to activate this mode temporarily, followed by another key. This displays the following icon at the bottom of the screen, until a second key is pressed: Press the Blue key twice to lock this mode. This displays the following icon at the bottom of the screen: Press the Blue key a third time to unlock.
2 - 26 MC75 User Guide Table 2-12 Alpha-numeric Keypad Descriptions (Continued) Key Shift Action Changes the state of the alpha characters from lowercase to uppercase. • Press the Shift key to activate this mode temporarily, followed by another key. This displays the following icon at the bottom of the screen, until a second key is pressed: • Press the Shift key twice to lock this mode. This displays the following icon at the bottom of the screen: • Press the Shift key a third time to unlock.
Using the MC75 2 - 27 Table 2-13 QWERTY Keypad Input Modes Key Normal Shift + Key Orange + Key Blue + Key Q q Q * Start Menu W w W 1 Menu E e E 2 Phone R r R 3 T t T + Y y Y _ U u U - I i I = O o O “ P p P áü A a A # S s S 4 D d D 5 F f F 6 G g G ( H h H ) J j J / K k K : L l L ‘ Backspace Backspace Shift Shift Z z Z 7 X x X 8 C c C 9 V v V % B b B & N n N ! M m M ? , , < @ OK Note: An
2 - 28 MC75 User Guide Table 2-13 QWERTY Keypad Input Modes (Continued) Key Normal Shift + Key Orange + Key Blue + Key ENTER Enter Backlight Backlight Backlight 0 Backlight TAB Tab Tab Back tab Tab SPACE Space Space Space Space Star * * * * . . > . . Note: An application can change the key functions. The keypad may not function exactly as described.
Using the MC75 2 - 29 Table 2-14 AZERTY Keypad Input Modes (Continued) Key Normal Shift + Key Orange + Key Blue + Key Shift Shift W w W 7 X x X 8 C c C 9 V v V % B b B & N n N ! , , < @ Backspace backspace Enter Enter Backlight Backlight Backlight 0 Backlight TAB Tab Tab Back tab Tab SPACE Space Space Space Space Star * * * * . . > . . Note: An application can change the key functions. The keypad may not function exactly as described.
2 - 30 MC75 User Guide Table 2-15 QWERTZ Keypad Input Modes (Continued) Key Normal Shift + Key Orange + Key Blue + Key S s S 4 D d D 5 F f F 6 G g G ( H h H ) J j J / K k K : L l L ‘ Backspace Backspace Shift Shift Y y Y 7 X x X 8 C c C 9 V v V % B b B & N n N ! M m M ? , , < @ ENTER Enter Backlight Backlight Backlight 0 Backlight TAB Tab Tab Back tab Tab SPACE Space Space Space Space Star * * * * . . > . .
Using the MC75 2 - 31 character, move the cursor to the right of the character then press the Orange key twice and then press the áü key until the special character replaces the original character. Table 2-16 lists the special characters you can generate. Table 2-16 Special Characters Key Special Characters Key a A c C d D e E i I l L n N o O p P r R s S t T u U y Y z Z $ / “ ( ) + ! .
2 - 32 MC75 User Guide Function Buttons The MC75’s buttons perform certain functions. Power Button Scan/Action Button Up/Down Button Action Button Scan/Action Button Figure 2-17 Function Buttons • Power: Press the red Power button to turn the MC75 screen on and off. The MC75 is in suspend mode when the screen is off. For more information, see Powering On the MC75 on page 1-8. Also use the Power button to reset the MC75 by performing a warm or cold boot. See Resetting the MC75 on page 2-15.
Using the MC75 2 - 33 CAUTION To prevent damage to the screen, do not use any device other than the Motorola-provided stylus. Entering Data When entering data on the keypad, use either the single-hand method or the two-hand method as shown in Figure 2-18.
2 - 34 MC75 User Guide Data Capture The MC75 offers three types of data capture options: • Linear scanning • Imaging • Digital camera. NOTE To perform data capture a scanning enabled application must be installed on the MC75. A sample scanning application can be downloaded from the Motorola Support site at http://support.symbol.com.
Using the MC75 2 - 35 Digital Camera MC75 with an integrated digital camera have the following features: • Omnidirectional reading of a variety of bar code symbologies, including the most popular linear, postal, PDF417, and 2D matrix code types. • Advanced intuitive aiming for easy point-and-shoot operation.
2 - 36 MC75 User Guide Figure 2-19 Linear Scanning 3. Press the scan button. Ensure the red scan beam covers the entire bar code. The Scan/Decode LED lights red to indicate that scanning is in process, then lights green and a beep sounds, by default, to indicate the bar code was decoded successfully. Correct Incorrect Figure 2-20 Linear Scanner Aiming Pattern Imager Scanning 1. Ensure that a scan-enabled application is loaded on the MC75. 2. Aim the scan window at the bar code.
Using the MC75 2 - 37 Linear bar code PDF417 symbol Symbol View Finder (Aiming Pattern) Correct Figure 2-22 Imager Aiming Pattern: Bar Code Centered Incorrect Correct Figure 2-23 Imager Aiming Pattern: Bar Code Not Centered Figure 2-24 Pick List Mode with Multiple Bar Codes in Aiming Pattern 4. Release the scan button. NOTE Imager decoding usually occurs instantaneously.
2 - 38 MC75 User Guide Figure 2-25 Sample Scan Application with Preview Window 4. Move the MC75 until the red aiming reticle is on the bar code to scan. The aiming reticle turns green when the MC75 is able to decode the bar code. Figure 2-26 Digital Camera Scanning 5. Release the scan button. The Scan/Decode LED lights green and a beep sounds, by default, to indicate the bar code was decoded successfully.
Using the MC75 2 - 39 Refer to the RS507 Hands-free Imager Product Reference Guide for more information. Taking Photos To take a photo: 1. Tap Start > Programs > Pictures & Videos icon. 2. Tap Camera on the command bar. 3. Check the image on the view finder, adjust if necessary. 4. Press the Enter key to take the picture. Hold the MC75 still until the camera flash occurs or the shutter sound is heard. Recording Video To record a video clip: 1. Tap Start > Programs > Pictures & Videos icon. 2.
2 - 40 MC75 User Guide Using IrDA In a Microsoft Windows Mobile program (except Messaging), and Picture & Videos, you can exchange files using either infrared or Bluetooth. NOTE You can also beam files (not folders) from the File Explorer window. Tap and hold the item you want to send, then tap Beam File from the pop-up menu. First activate the beam function before exchanging files with another IrDA device. To activate the Beam function: 1. Tap Start > Settings > Connections tab > Beam icon. 2.
Using the MC75 2 - 41 Figure 2-28 Align MC75 with IrDA Device 3. Tap and hold the item, then tap Beam [type of item] on the pop-up menu. 4. Tap the device that you want to send the file to. Figure 2-29 Beam Contact To receive files via IrDA connection: 1. Align the IrDA port of the MC75 with that of the other IrDA device so that they are unobstructed and within a close range. 2. On the other device, send the file to the MC75.
2 - 42 MC75 User Guide Figure 2-30 Receive File 3. When the Receiving Data dialog displays, tap Yes.
Chapter 3 Using GPS Navigation Introduction The MC75 includes Global Positioning System (GPS) technology using the SiRF III chipset. GPS technology is based on a worldwide system of GPS satellites orbiting the earth that continuously transmit digital radio signals. These radio signals contain data on the satellites’ locations and their exact clock time and are used to determine your location on the earth.
3-2 MC75 User Guide To access the GPS receiver from multiple programs simultaneously, the user can either use the Microsoft GPS API or change the GPS program port setting and access the GPS program port in the multiplexed way. Operation Acquiring satellite signals may take a few minutes. It is best to be outside and have a clear, unobstructed view of the sky. Without a clear view, acquisition takes much longer and could result in the MC75 being unable to compute the initial position quickly.
Using GPS Navigation 3-3 improves the performance of the Time To First Fix (TTFF) of GPS receivers by providing them with data that they would ordinarily have to download from the GPS satellites. With the A-GPS data, GPS receivers can operate faster and more reliably. A-GPS follows the Secure User Plane Location (SUPL) protocol which allows the MC75 to communicate with a location server. Refer to the EMDK Help file for information on setting up SUPL on the MC75.
3-4 MC75 User Guide
Chapter 4 Using Bluetooth Introduction Bluetooth-equipped devices can communicate without wires, using frequency-hopping spread spectrum (FHSS) radio frequency (RF) to transmit and receive data in the 2.4 GHz Industry Scientific and Medical (ISM) band (802.15.1). Bluetooth wireless technology is specifically designed for short-range (30 feet/10 meters) communication and low power consumption. MC75s with Bluetooth capabilities can exchange information (e.g.
4-2 MC75 User Guide The Bluetooth radio in this MC75 operates as a Class 2 device power class. The maximum output power is 2.5mW and the expected range is 32.8 feet (10 meters). A definition of ranges based on power class is difficult to obtain due to power and device differences, and whether one measures open space or closed office space. NOTE It is not recommended to perform Bluetooth wireless technology inquiry when high rate 802.11b operation is required.
Using Bluetooth 4-3 Turning the Bluetooth Radio Mode On and Off NOTE On devices with Windows Mobile 6.5.3, turn the Bluetooth radio on or off using the Wireless Manager. Tap the Status bar and select the Connectivity icon. Tap Wireless Manager. Turn off the Bluetooth radio to save power or if entering an area with radio restrictions (e.g., an airplane). When the radio is off, other Bluetooth devices cannot see or connect to the MC75.
4-4 MC75 User Guide Bluetooth Power States Cold Boot Performing a cold boot on the MC75 turns off Bluetooth after initialization (which takes a few moments). It is normal to see the Bluetooth icon appear and disappear, as well as a wait cursor, when initialization proceeds in all modes. Warm Boot Performing a warm boot on the MC75 returns Bluetooth to the last state after initialization. Suspend Suspending the MC75 turns off Bluetooth.
Using Bluetooth 4-5 Figure 4-3 Explorer Mode Window You can also use the “tap and hold” technique to view available options. Scroll bars and view options are similar to those on the Windows desktop.
4-6 MC75 User Guide Discovering Bluetooth Device(s) The MC75 can receive information from discovered devices without bonding. However, once bonded, the MC75 and a bonded device exchange information automatically when you turn the Bluetooth radio on. See Bonding with Discovered Device(s) on page 4-20 for more information. To find Bluetooth devices in the area: 1. Ensure that Bluetooth is enabled on both devices. 2. Ensure that the Bluetooth device to discover is in discoverable and connectable modes.
Using Bluetooth 4-7 • Send or Exchange Objects • Associate Serial Port. NOTE 8. If a device discovery action has not been previously performed, a device discovery is automatically initiated. If a device discovery has previously been performed, the device discovery process is skipped, and the previously found list of devices displays. To start a new device discovery, tap and hold in the window and select Discover Devices from the pop-up menu. BTExplorer searches for Bluetooth devices in the area.
4-8 MC75 User Guide Figure 4-7 Device Services NOTE If the MC75 discovers a service but the service is not supported, the service icon is grayed-out. 10. Select a service from the list and press Next. The Connection Favorite Options window appears. Figure 4-8 Connection Favorite Options Window 11. In the Favorite Name text box, enter a name for this service that will appear in the Favorite window. 12. Tap Next. The Connection Summary window appears. 13.
Using Bluetooth 4-9 Figure 4-9 Favorites Window Available Services NOTE Some devices might not require a PIN. This depends upon the device’s authentication. The MC75 offers the following services: • File Transfer Services • Dial-Up Networking Services • OBEX Object Push Services • Headset Audio Gateway Services • Hands-Free Audio Gateway Services • Serial Port Services • Personal Area Networking Services • IrMC Services. See the following sections for information on these services.
4 - 10 MC75 User Guide 4. Select the device and tap Next. The Select Remote Service window appears. 5. Tap Next. The Connection Favorite Options window appears. 6. Tap Next. The Connection Summary window appears. 7. Tap Connect. The remote device’s accessible folders appear. Figure 4-10 File Transfer Window 8. Double-tap the file to copy. The Save Remote File window appears. Figure 4-11 Save Remote File Window 9. Tap and hold on the file. A pop-up menu appears. 10.
Using Bluetooth 4 - 11 2. Enter the name for the new folder or file. 3. Tap OK to create the new folder or file on the remote device. Deleting a File To delete a file from the remote device: 1. Tap and hold on the file to delete and select Delete. 2. In the Delete Remote Device File dialog box tap Yes. Getting a File To copy a file from a remote device: 1. Double-tap or tap and hold on the file and select Get. The Save Remote File window appears. 2. Navigate to the directory to save the file.
4 - 12 MC75 User Guide Dial-Up Networking Services Dial-up networking allows the user to connect a PC or laptop to the MC75 and use the MC75 as a modem to connect to an office network or ISP. Before setting up dial-up networking, obtain dial-up information and other necessary settings (username, password and domain name, if required) for the office network or ISP. To create a new Bluetooth connection: 1. Ensure the MC75 is discoverable and connectable. See Device Info Tab on page 4-23. 2.
Using Bluetooth 4 - 13 2. Ensure that the OBEX Object Push profile is enabled on the MC75. See Profiles Tab on page 4-32 for more information. NOTE If favorite connections have already been created, the Favorites screen displays. If no favorite connections have been created, the New Connection Wizard screen displays. 3. Use the Connection Wizard to search for a Bluetooth device. 4. Select the device and tap Next. 5. Select the OBEX Object Push service and select Connect.
4 - 14 MC75 User Guide Figure 4-14 Select Contact Entry Window 4. Select a contact to send to the other device. 5. Tap OK. 6. Tap OK to send the contact to the other device and display a confirmation dialog box on the other device to accept the contact. A Send Contact dialog appears. 7. Tap Ok. Swapping Contacts To swap contacts with another device: NOTE 1. Prior to swapping contacts, a default contact must be set up before attempting to send a contact.
Using Bluetooth 4 - 15 Figure 4-16 Select Contact Entry Window 4. Select a contact to send to the other device. 5. Tap OK. 6. Tap OK to swap contacts with the other device and display a confirmation dialog box on the other device to accept the contact. 7. Tap Ok. Fetching a Contact To fetch a contact from another device: NOTE 1. Prior to sending and receiving contacts, a default contact must be set up before attempting to send a contact. Tap and hold on OBEX Object Push and select Connect.
4 - 16 MC75 User Guide 1. Tap and hold on OBEX Object Push and select Connect. The OBEX Object Push window appears. Figure 4-18 OBEX Object Push Window 2. In the Action: drop-down list, select Send A Picture. 3. Tap . The Send Local Picture window appears. Figure 4-19 Send Local Picture Window 4. Navigate to the picture to send to the other device. 5. Tap Open. 6. Tap OK to send the picture to the other device and display a confirmation dialog box on the other device to accept the picture.
Using Bluetooth 4 - 17 2. Ensure that the Headset profile is enabled on the MC75. See Profiles Tab on page 4-32 for more information. 3. Use the Connection Wizard to search for a Bluetooth headset. 4. Select the device and tap Next. 5. Select the Headset service name and select Connect. The MC75 connects to the headset. Refer to the headset user manual for instructions on communicating with a Bluetooth device.
4 - 18 MC75 User Guide Headset icon Figure 4-20 WWAN Bluetooth Audio Notification Dialog Box Serial Port Services Use the wireless Bluetooth serial port connection as you would a physical serial cable connection. Configure the application that will use the connection to the correct serial port. To establish a serial port connection: 1. Ensure the MC75 is discoverable and connectable. See Device Info Tab on page 4-23. 2. Use the Connection Wizard to search for a Bluetooth serial device. 3.
Using Bluetooth 4 - 19 Figure 4-21 ActiveSync Connection Settings Window on PC To establish an ActiveSync connection: 1. Ensure the MC75 is discoverable and connectable. See Device Info Tab on page 4-23. 2. Ensure that the Sync profile is enabled on the MC75. See Profiles Tab on page 4-32 for more information. 3. Use the Connection Wizard to search for a Bluetooth device, such as a PC. In the drop-down list select ActiveSync via Bluetooth. 4. Select the device and tap Next.
4 - 20 MC75 User Guide Personal Area Network Services NOTE This profile supports Ad-hoc and PAN User. Network Access Profile is not supported. Connect two or more Bluetooth devices to share files, collaborate, or play multi-player games. To establish a Personal Area Network connection: 1. Ensure the MC75 is discoverable and connectable. See Device Info Tab on page 4-23. 2. Ensure that the Personal Area Networking profile is enabled on the MC75. See Profiles Tab on page 4-32 for more information. 3.
Using Bluetooth 4 - 21 To bond with a discovered Bluetooth device: NOTE If favorite connections have already been created, the Favorites screen displays. If no favorite connections have been created, the New Connection Wizard screen displays. 1. Tap the Bluetooth icon and select Show BTExplorer. The BTExplorer window appears. 2. Tap Menu > New Connection. The New Connection Wizard window appears. 3. In the drop-down list, select Pair with Remote Device. 4. Tap Next.
4 - 22 MC75 User Guide Figure 4-25 Pairing Status Window 8. Tap Finish. The devices are successfully paired. The device name moves to the Trusted Devices window. Deleting a Bonded Device To delete a device no longer needed: 1. Tap the Bluetooth icon and select Show BTExplorer. The BTExplorer window appears. 2. Tap Menu > Trusted Devices. The Trusted Devices window appears. 3. Tap and hold on the device select Delete Link Key in the pop-up menu. 4. A confirmation dialog appears. Tap Yes.
Using Bluetooth 4 - 23 4. Tap OK to create the bond. The MC75 can now exchange information with the other device. Bluetooth Settings Use the BTExplorer Settings window to configure the operation of the BTExplorer application. Tap Menu > Settings. The BTExplorer Settings window appears. Device Info Tab Use the Device Info tab to configure the MC75’s Bluetooth connection modes. Figure 4-27 BTExplorer Settings - Device Info Tab Device Name Displays the name of the MC75.
4 - 24 MC75 User Guide To add a service: 1. Tap Add. The Add Local Service window displays. Figure 4-29 Add Local Service Window 2. In the list, select a service to add. 3. Tap OK. The Edit Local Service window displays for the selected service. 4. Select the appropriate information and then tap OK. See the following sections for information on the available services. Dial-Up Networking Service Dial-up Networking allows other Bluetooth devices to access a dial-up modem.
Using Bluetooth 4 - 25 Table 4-1 Item Description Local COM Port Select the COM port. Local Baud Rate Select the communication baud rate. Local Port Options Select the port option. File Transfer Service File transfer allows other Bluetooth devices to browse files. Figure 4-31 BTExplorer Settings - File Transfer Information Table 4-2 File Transfer Information Data Item Description Service Name Displays the name of the service.
4 - 26 MC75 User Guide Hands-Free Audio Gateway Service Hands-Free Service Audio Gateway allows connection to hands-free devices. Figure 4-32 BTExplorer Settings - Hands-Free Audio Gateway Table 4-3 Hands-Free Audio Gateway Data item Service Name Description Lists the name of the audio service. Headset Audio Gateway Service Headset Service Audio Gateway allows connection to headset devices.
Using Bluetooth 4 - 27 Figure 4-34 BTExplorer Settings - IrMC Synchronization Table 4-5 IrMC Synchronization Data Item Description Service Name Displays the name of the service. Service Security Select the type of security from the drop-down list. Options are None, Authenticate, or Authenticate/Encrypt. Phonebook Select the Phonebook checkbox to allow synchronization with the MC75’s contacts. Select Read, Write, Create and/or Delete to allow phonebook permissions.
4 - 28 MC75 User Guide Figure 4-35 BTExplorer Settings - OBEX Exchange Information Table 4-6 OBEX Exchange Information Data Item Description Service Name Displays the name of the service. Service Security Select the type of security from the drop-down list. Options are None, Authenticate, or Authenticate/Encrypt. Do not allow clients to push objects Disables clients from pushing objects to the MC75. Inbox Directory Select a directory where another Bluetooth device can store files.
Using Bluetooth 4 - 29 Table 4-7 Personal Area Networking Data Item Description Service Name Displays the name of the service. Service Security Select the type of security from the drop-down list. Options are None, Authenticate, or Authenticate/Encrypt. Support Group Ad-Hoc Networking Select to enable Ad-Hoc networking. Serial Port Service Serial port allows other Bluetooth devices to access COM ports.
4 - 30 MC75 User Guide Figure 4-38 BTExplorer Settings - Security Tab NOTE To use PIN Code, select Authenticate or Authenticate/Encrypt from the Service Security drop-down list on each local service. Table 4-9 Security Tab Data Item Description Use PIN Code (Incoming Connection) Select for automatic use of the PIN code entered in the PIN Code text box. It is recommended not to use this automatic PIN code feature. See Security on page 4-2 for more information. PIN Code Enter the PIN code.
Using Bluetooth 4 - 31 Table 4-10 Discovery Tab Data Item Description Inquiry Length Sets the amount of time the MC75 takes to discover Bluetooth devices in the area. Name Discovery Mode Select either Automatic or Manual to automatically attempt to discover a Bluetooth device's name after finding the device. Discovered Devices - Delete Devices Deletes all discovered devices and link keys from memory.
4 - 32 MC75 User Guide HID Tab Use the HID tab to select The Human Interface Device Profile programming interface defines the protocols and procedures to be used to implement HID capabilities. Provides support for devices such as mice, joysticks, keyboards. Figure 4-41 BTExplorer Settings - HID Tab Table 4-12 HID Tab Data Item Description Enable Key Repeat Enables key repeat functionality. Delay To increase key repeat delay, drag the Delay slider to the right.
Using Bluetooth 4 - 33 The Serial Port profile is always active and cannot be removed. 2. Tap Select All to select all profiles or tap Deselect All to deselect all profiles. 3. Tap Apply to activate the profiles and then Close to exit the application. System Parameters Tab Figure 4-43 BTExplorer Settings - System Parameters Tab Table 4-13 System Parameters Tab Data item Description Page Timeout Sets the amount of time the MC75 searches for a device before moving on the next device.
4 - 34 MC75 User Guide Table 4-14 Miscellaneous tab Data Item Description Highlight Connections Select the connection type to highlight when connected. In the Wizard Mode, the only options are Favorites or None. In the Explorer Mode the options are None, Tree View Only, List View Only, or Tree and List View. Apply Text Style Select the text style to apply to the connection text. Apply Text Color Select the text color to apply to the connection text.
Chapter 5 Using the Phone Introduction Use the MC75 to make phone calls, set up speed dials, keep track of calls, and send text messages. Your wireless service provider may also provide other services such as voice mail, call forwarding, and caller ID. Also use the integrated phone to connect to an ISP or work network in order to browse the Web and read e-mail.
5-2 MC75 User Guide To access the phone keypad tap Start > Phone or press the green phone key on the MC75’s keypad. To receive calls when the MC75 is suspended, leave the phone radio turned on and ensure the MC75 is set to wake with any key. Turning the Phone On and Off NOTE On devices with Windows Mobile 6.5.3, see Status Bar on page C-5 for more information. Windows Mobile 6 devices include Wireless Manager, which provides a simple method of enabling and disabling the phone.
Using the Phone 5-3 Audio Modes The MC75 offers three audio modes for use during phone calls: • Handset Mode: Switches audio to the speaker at the top front of the MC75, so you can use the MC75 as a handset. This is the default mode. • Speaker Mode: Use the MC75 as if on speaker phone. Tap the Speaker On button to activate this mode. Tap the Speaker Off button to switch back to handset mode. • Headset Mode: Connect a wired or Bluetooth headset to automatically switch audio to the headset.
5-4 MC75 User Guide Figure 5-4 Using a Headset Using a Bluetooth Headset You can use a Bluetooth headset for audio communication when using an audio-enabled application. See Chapter 4, Using Bluetooth for information on connecting a Bluetooth headset to the MC75. Set the MC75’s volume appropriately before putting the headset on. When a Bluetooth headset is connected the speakerphone is muted. It is recommended for phone conversations to use the Bluetooth Hands-free profile instead of the Headset profile.
Using the Phone 5-5 Phone Volume Slider Figure 5-6 Phone Volume Slider To adjust the volume tap the Speaker icon in the Title bar. Move the slider up or down to adjust the volume. NOTE Adjust the conversation phone volume during a call. Adjusting the volume while not in a call affects the ring and notification sound levels. Making a Call NOTE You can make emergency calls even when the MC75 is locked or when a SIM card is not installed. See Making an Emergency Call on page 5-7 for more information.
5-6 MC75 User Guide Figure 5-7 Contacts Menu 3. Tap Call Work, Call Home or Call Mobile. NOTE To make a call from an open contact, tap the number to call. See On-Device Help for more information about Contacts. Using Call History To make a call using Call History: 1. Tap Start > Phone or press the green phone key on the MC75’s keypad. 2. From the Phone keypad, tap Call History. Phone icon Figure 5-8 Call History 3.
Using the Phone 2. 5-7 From the Phone keypad, tap and hold the speed dial location number assigned to a contact. (To dial a one-digit speed dial location number, tap and hold the speed dial number. To dial a two-digit speed dial location number, tap the first digit and then tap and hold the second digit.) or From the Phone keypad, tap Speed Dial and tap the speed dial location number of the desired contact in the list. Speed Dial Location Number Figure 5-9 Speed Dial Contact List 3.
5-8 MC75 User Guide Figure 5-10 Incoming Call To ignore the incoming call tap Ignore. This may send the caller to voice mail, depending on the service provider. Otherwise, this presents busy signal to the calling party. To end the call tap End or press the red phone key on the MC75 keypad. Incoming Call Features • If you receive a call while in a call, tap Wait to place the call in call waiting. • You can use other programs on the MC75 during a call.
Using the Phone 5-9 To find a contact name: • Enter the first letter of a contact’s first name or last name. Smart Dialing searches for the letter starting from the first character of a contact name as well as from the character that appears after a space, dash, or underscore in a contact name.
5 - 10 MC75 User Guide Mute Icon Figure 5-12 Mute Button and Icon Taking Notes To create a note during a call, tap Note on the display, then enter the note. For more information about creating notes see the Windows On-Device Help. To access a note created during a call: 1. Tap Start > Phone or press the green phone key on the MC75’s keypad. 2. From the Phone keypad, tap Call History. 3. Tap and hold the number or the Note icon for the phone call entry containing the note.
Using the Phone 5 - 11 Figure 5-14 Call History - Notes 5. Tap ok to exit. NOTE Also access notes directly from the Notes application by tapping Start > Notes. Using Speed Dial Create speed dial numbers to dial frequently called numbers with a single tap. Before creating a speed dial entry, ensure the phone number exists in Contacts. Adding a Speed Dial Entry To add a speed dial entry from the phone keypad: 1. Ensure the contact and phone number are in the Contacts list. 2.
5 - 12 MC75 User Guide Figure 5-16 Speed Dial Contact Location 5. In the Location field, tap the up/down arrows to select an available location to assign as the new speed dial entry. The first speed dial location is reserved for voice mail. 6. Tap ok to add the contact to the speed dial list. Figure 5-17 Speed Dial Contact List 7. Tap ok to exit the Speed Dial Contact List. To add a speed dial entry from the Contacts window: 1. Tap Start > Contacts.
Using the Phone 5 - 13 Figure 5-18 Contacts 2. Tap a contact name. 3. Tap Menu > Add to Speed Dial. Figure 5-19 Speed Dial Contact Location 4. Tap the up/down arrows to select an available location to assign as the new speed dial entry. The first speed dial location is reserved for voice mail. 5. Tap ok. Editing a Speed Dial Entry 1. Tap Start > Phone or press the green phone key on the MC75’s keypad. 2. Tap Menu > Speed Dial.
5 - 14 MC75 User Guide Figure 5-20 Speed Dial Contact List 3. Tap and hold the contact name. 4. Tap Edit... . 5. Change the name, phone number, or location information. 6. Tap ok. NOTE Editing names and phone numbers in Speed Dial does not alter contact information in Contacts (Start > Contacts). Deleting a Speed Dial Entry 1. Tap Start > Phone or press the green phone key on the MC75’s keypad. 2. Tap Menu > Speed Dial. 3. Tap and hold the contact name. Figure 5-21 Speed Dial Delete Menu 4.
Using the Phone 5 - 15 Using Call History Use Call History to call someone who was recently called, or recently called in. Call History provides the time and duration of all incoming, outgoing, and missed calls. It also provides a summary of total calls and easy access to notes taken during a call. Table 4-1 lists the call history icons that appear in the Call History window. Table 5-1 Call History Icons Icon Description This icon appears next to the contact information for all outgoing calls.
5 - 16 MC75 User Guide 3. Tap Menu. Figure 5-23 Call History - Tools Menu 4. Select Call Timers... . Figure 5-24 Call History - Call Timers 5. Tap Reset. (The All Calls: counter cannot be reset.) 6. Tap ok to exit the Call Timers window. Deleting Call History Items by Call Date 1. Tap Start > Phone or press the green phone key on the MC75’s keypad to display the Phone keypad. 2. From the Phone keypad, tap Call History. 3. Tap Menu > Call Timers... .
Using the Phone 5 - 17 Figure 5-25 Call History - Call Timers 4. In the Delete call history items older than: drop-down list select a time period on which to base deletion of stored items. 5. Tap ok to exit the Call Timers window. Deleting All Call History Items 1. Tap Start > Phone or press the green phone key on the MC75’s keypad to display the Phone keypad. 2. From the Phone keypad, tap Call History. 3. Tap Menu. Figure 5-26 Call History - Tools Menu 4. Select Delete all calls.
5 - 18 MC75 User Guide Viewing Call Status 1. Tap Start > Phone or press the green phone key on the MC75’s keypad to display the Phone keypad. 2. From the Phone keypad, tap Call History. 3. Tap an entry. The Call Status window appears. Figure 5-28 Call History - Detail NOTE 4. When more than one call is on the phone line, only the duration of the first call is recorded. Tap ok and then ok to exit.
Using the Phone 5 - 19 5. Depending on the item selected, the appropriate window displays. For example, select Send SMS to display the Inbox window. 6. Tap ok to exit the Call History window. Swapping Calls on an MC7506/96 To move between two or more phone calls: 1. Tap Start > Phone or press the green phone key on the MC75’s keypad to display the Phone keypad. 2. Enter the first phone number and press Talk. When the call connects, Hold appears on the keypad.
5 - 20 MC75 User Guide Swapping Calls on an MC7508/98 To swap between two incoming phone calls: 1. Tap Answer to connect to the first call. Figure 5-32 Answer a Call 2. When a second call arrives, tap Answer. The first call is placed on hold. 3. Tap Talk to swap from one call to the other. Figure 5-33 Call Swapping 4. Tap End or press the red phone key on the MC75 keypad to end active call. The remaining call re-connects, tap Answer to connect to the call. 5.
Using the Phone 5 - 21 2. Enter the first phone number and press Talk. When the call connects, Hold appears on the keypad. Figure 5-34 Conference Call - Hold 3. Tap Hold to place the first call on hold. 4. Enter the second phone number and tap Talk. 5. After the call is answered, tap Menu > Conference to place the calls in conference mode. Figure 5-35 Creating a Conference Call 6. Tap Hold to place the conference on hold. 7. Enter another phone number and tap Talk. 8.
5 - 22 MC75 User Guide Figure 5-36 Creating a Private Call Three-way Calling on an MC7508/98 NOTE Three-way Calling may not be available on all services. Please check with your service provider for availability. To create a three-way phone session with two people and you as the initiator: 1. Tap Start > Phone or press the green phone key on the MC75’s keypad to display the Phone keypad. 2. Enter the first phone number and press Talk. 3. To call a second person, tap Keypad.
Using the Phone 5 - 23 Text Messaging Use the Text Messages window to send and receive text messages to and from mobile phones. The text can contain words, numbers, or an alphanumeric combination no longer than 160 characters. Short text messages delivered over mobile networks transmit from the sending MC75, are stored in a central short message center, then forwarded to the destination mobile device. If the recipient is not available, the message is stored and can be sent later.
5 - 24 MC75 User Guide Tap Text Messages. Figure 5-40 Text Messaging on Today Screen The Messaging window appears. Figure 5-41 Messaging Window 2. In the message list, tap a Text Messages. Tap to reply the message. Figure 5-42 Text Messages List NOTE If the phone is turned off and you tried to call the sender, send a reply, or forward the message, you are prompted to turn the phone function on. Sending a Text Message To create a text message: 1.
Using the Phone 5 - 25 2. Tap Menu > Send Text Message. Figure 5-43 Phone Screen Contact List 3. Compose your message. Address Area Message Area Figure 5-44 Create Text Message • The auto-correct feature automatically fixes common spelling errors as you type so your messages are more accurate. • The character counter lets you see and control the size of the message as you compose.
5 - 26 MC75 User Guide If the phone is turned on, your text message is sent. If it’s off, you are prompted to turn on the phone. If you do so, the message is sent; otherwise when you tap ok, the message is saved in the Drafts folder and sent when the phone is turned on. If you are out of coverage area, the message is saved in the Drafts folder and sent when you return to a coverage area.
Using the Phone 5 - 27 3. Select Change and then tap Select. 4. If applicable, sign in with the PIN number for the other line.
5 - 28 MC75 User Guide
Chapter 6 Accessories Introduction MC75 accessories, listed below, provide a variety of product support capabilities. • Four Slot Ethernet Cradle - Charges the MC75 main battery and connects the MC75 with an Ethernet network. • Four Slot Charge Only Cradle - Charges up to four MC75 devices. • Single Slot USB/Serial Cradle - Charges the MC75 main battery and a spare battery. Synchronizes the MC75 with a host computer through a USB connection.
6-2 MC75 User Guide • Debit Card Reader - snaps onto the bottom of the MC75 to allow easy data capture with the swipe of a magnetic stripe card and personal identification number (PIN) entry using a numeric keypad. • Snap-on Mobile Payment Module with Chip and PIN - snaps onto the bottom of the MC75 to allow easy data capture with magnetic stripe cards, EMV compliant Chip and PIN cards and personal identification number (PIN) entry using a numeric keypad.
Accessories 6-3 Charging the Spare Battery Spare Battery Spare Battery Charging LED Figure 6-2 Spare Battery Charging Battery Charging Indicators The Single Slot USB/Serial Cradle charges the MC75’s main battery and a spare battery simultaneously. The MC75’s charge LED indicates the status of the battery charging in the MC75. See Table 1-2 on page 1-8 for charging status indications. The spare battery charging LED on the cradle indicates the status of the spare battery charging in the cradle.
6-4 MC75 User Guide Four Slot Ethernet Cradle This section describes how to set up and use a Four Slot Ethernet cradle with the MC75. For cradle communication setup procedures refer to the MC75 Integrator Guide. The Four Slot Ethernet cradle: • Provides 5.4 VDC power for operating the MC75. • Connects the MC75 (up to four) to an Ethernet network. • Simultaneously charges up to four MC75 devices. Charging Insert the MC75 into a slot to begin charging.
Accessories 6-5 Four Slot Charge Only Cradle This section describes how to set up and use a Four Slot Charge Only cradle with the MC75. The Four Slot Charge Only cradle: • Provides 5.4 VDC power for operating the MC75. • Simultaneously charges up to four MC75 devices. Charging Insert the MC75 into a slot to begin charging. Figure 6-4 MC75 Battery Charging Battery Charging Indicators The MC75’s charge LED shows the status of the battery charging in the MC75.
6-6 MC75 User Guide VCD7X00 Vehicle Cradle This section describes how to use a VCD7X00 vehicle cradle with the MC75. For cradle installation and communication setup procedures refer to the MC75 Integrator Guide. Once installed in a vehicle, the cradle: • holds the MC75 securely in place • provides power for operating the MC75 • provides a serial port for data communication between an MC75 and an external device (e.g.
Accessories 6-7 Release Lever Figure 6-6 Removing the MC75 Charging the Spare Battery Insert a spare battery to begin charging: 1. Lift the battery release lever. Battery Release Lever Battery Figure 6-7 Inserting the Spare Battery 2. Insert the spare battery in the spare battery charging slot in the cradle with the charging contacts facing up and to the rear of the cradle. 3. Release the battery release lever. The battery release lever locks the spare battery into place.
6-8 MC75 User Guide Battery Charging Indicators The Vehicle Cradle charges the MC75’s main battery and a spare battery simultaneously. The MC75’s charge LED indicates the status of the battery charging in the MC75. See Table 1-2 on page 1-8 for charging status indications. The spare battery charging LED on the cradle indicates the status of the spare battery charging in the cradle. See Table 6-2 for charging status indications.
Accessories Four Slot Battery Charger This section describes how to use the Four Slot Battery Charger to charge up to four MC75 batteries. MC75 Battery Shim Installation Before charging a spare battery, snap the MC75 shim into the battery slot as shown in Figure 6-9. Shim Figure 6-9 MC75 Battery Shim Installation NOTE To purchase additional shims, contact your local account manager or Motorola, Inc. Part number: KT-76490-01R. Spare Battery Charging 1. Connect the charger to a power source. 2.
6 - 10 MC75 User Guide Spare Battery Spare Battery Charging LEDs (4) Figure 6-10 Four Slot Battery Charger Battery Charging Indicators The charger has an amber LED for each battery charging well. See Table 6-3 for charging status indications. The 3600 mAh battery fully charges in less than five hours and the 4800 mAh battery fully charges in less than seven hours. Charging Temperature Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the MC75.
Accessories 6 - 11 Magnetic Stripe Reader (MSR) This section describes how to set up and use the snap-on MSR with the MC75. The MSR snaps on to the bottom of the MC75 and removes easily when not in use. When attached to the MC75, the MSR allows the MC75 to capture data from magnetic stripe cards. To download MSR data capture software, visit the Motorola web site at http://www.symbol.com/support.
6 - 12 MC75 User Guide Figure 6-12 Magnetic Stripe Card Swiping 5. The application indicates if the data has been read correctly.
Accessories 6 - 13 Debit Card Reader The DCR7X00-100R Debit Card Reader (DCR) snaps onto the bottom of the MC75 to allow easy data capture with the swipe of a magnetic stripe card and personal identification number (PIN) entry using a numeric keypad. Getting Started When using the DCR for the first time, charge the DCR in a cradle for a minimum of three hours. Installation 1. Align the DCR with the bottom of the MC75 and push up until the locking tabs snap into place. Figure 6-13 DCR Installation 2.
6 - 14 MC75 User Guide Figure 6-14 DCR Removal Credit Card Transactions Launch a transaction application on the MC75. In the application, select Credit Card transaction. Swipe the credit card through the magnetic stripe reader (MSR) slot, orienting the magnetic stripe as shown. Data encoded on the credit card is captured and, depending on the application, may display in an application data field. Figure 6-15 Swipe Card NOTE Swipe the card in either direction, from left to right, or right to left.
Accessories 6 - 15 Figure 6-16 Swipe Card NOTE Swipe the card in either direction, from left to right, or right to left. For best results, gently press down on the card while swiping to ensure contact with the bottom of the slot. Turn the MC75 over and present the DCR keypad to the customer. The customer enters their PIN following the instructions on the DCR display. Figure 6-17 Enter PIN on DCR Keypad The back of the DCR contains a display and a numeric keypad for entering data.
6 - 16 MC75 User Guide Table 6-4 Keypad Key Descriptions Key Description Numeric Used to enter PIN. Cancel Cancels the current transaction. Clear Clears the entered data. Enter Submits the entered data. Display Messages The follow messages may appear on the DCR display: ENTER PIN - A PIN is required to complete the transaction. PIN ERR - The entered PIN is not between 4 and 12 characters. CANCELED - The transaction was cancelled by the user. COMPLETE - The transaction was completed.
Accessories 6 - 17 • BATT LOW - Battery charge is low. If BATT LOW displays, charge the DCR for approximately three hours. To charge the DCR, place it in a cradle or connect it to a charging cable. The DCR also charges when connected to the MC75 and the transaction application is running.
6 - 18 MC75 User Guide Snap-on Mobile Payment Module with Chip and PIN The DCR7X00-200R Snap-on Mobile Payment Module with Chip and PIN smart card reader snaps onto the bottom of the MC75 to allow easy data capture with magnetic stripe cards, EMV compliant Chip and PIN cards and personal identification number (PIN) entry using a numeric keypad. Installation NOTE 1. The module only functions when attached to the MC75.
Accessories 6 - 19 Credit Card Transactions NOTE Credit Card transactions will function without an encryption key injected but will not function if a tamper event occurs. Launch a transaction application on the MC75. In the application, select Credit Card transaction. Swipe the credit card through the magnetic stripe reader (MSR) slot, orienting the magnetic stripe as shown. Data encoded on the credit card is captured and, depending on the application, may display in an application data field.
6 - 20 MC75 User Guide Figure 6-24 Enter PIN Chip and PIN Transactions NOTE Chip and PIN transactions will function without an encryption key injected but will not function if a tamper event occurs. Launch a transaction application on the MC75. In the application, select Chip and PIN transaction. Customer inserts the Chip and Pin card into the slot, orienting the card with the contacts facing down and toward the DCR keypad.
Accessories 6 - 21 Figure 6-26 Keypad Table 6-5 Keypad Button Descriptions Key Description Numeric Used to enter PIN. Cancel (Red) Cancels the current transaction. Clear (Yellow) Clears the entered data. Enter (Green) Submits the entered data. Display Messages After connecting the module to the MC75 and an application opens the COM port, the following displays: . Figure 6-27 Display Line 1 indicates the model number and the firmware version.
6 - 22 MC75 User Guide Table 6-6 Keyload Codes Display D D D - M M - M M - M M - Operating Status Normal M M - d---dmm-d--mm -mm----mm Return to key injection facility. ***** Blank display Return to Motorola for service. The follow messages may appear on the display: Table 6-7 Display Messages Message Description Line 1: Line 2: Enter PIN Instructs the user to enter their PIN.
Accessories 6 - 23 Headset Use the headset to communicate via Voice-Over-IP (VOIP) or for audio playback and telephony applications. To connect the headset, remove the plug from the headset jack at the top of the MC75 and insert the headset connector. Contact a Motorola representative for compatible headsets. For best performance, Motorola recommends a 2.5mm jack headset, p/n 50-11300-050R.
6 - 24 MC75 User Guide Cables This section describes how to set up and use the cables. The cables are available with a variety of connection capabilities. The following communication/charge cables are available: • Serial (RS232) Charge cable (9-pin D female with power input receptacle) • USB Client Charge cable (standard-A connector and a barrel receptacle for power) • Auto charge cable • DEX cable • Modem inverter cable • Charge only cable.
Accessories 6 - 25 2. Slide the bottom of the MC75 into the connector end of the communication/charge cable and gently press in until it latches into the MC75. The MC75 amber Charge LED indicates the MC75 battery charging status. The 3600 mAh standard battery charges in less than five hours and the 4800 mAh standard battery charges in less than seven hours. See Table 1-2 on page 1-8 for charging status indications. 3.
6 - 26 MC75 User Guide
Chapter 7 Maintenance & Troubleshooting Introduction This chapter includes instructions on cleaning and storing the MC75, and provides troubleshooting solutions for potential problems during MC75 operation. Maintaining the MC75 For trouble-free service, observe the following tips when using the MC75: • Do not scratch the screen of the MC75. When working with the MC75, use the supplied stylus or plastic-tipped pens intended for use with a touch-sensitive screen.
7-2 MC75 User Guide • A screen protector is applied to the MC75. Motorola recommends using this to minimize wear and tear. Screen protectors enhance the usability and durability of touch screen displays. Benefits include: • Protection from scratches and gouges • Durable writing and touch surface with tactile feel • Abrasion and chemical resistance • Glare reduction • Keeping the device’s screen looking new • Quick and easy installation.
Maintenance & Troubleshooting 7-3 Cleaning CAUTION Always wear eye protection. Read warning label on compressed air and alcohol product before using. If you have to use any other solution for medical reasons please contact Motorola for more information. WARNING! Avoid exposing this product to contact with hot oil or other flammable liquids. If such exposure occurs, unplug the device and clean the product immediately in accordance with these guidelines.
7-4 MC75 User Guide 8. Spray compressed air on the connector area by pointing the tube/nozzle about ½ inch away from the surface. CAUTION: Do not point nozzle at yourself and others, ensure the nozzle or tube is away from your face. 9. Inspect the area for any grease or dirt, repeat if required. Cleaning Cradle Connectors To clean the connectors on a cradle: 1. Remove the DC power cable from the cradle. 2. Dip the cotton portion of the cotton tipped applicator in isopropyl alcohol. 3.
Maintenance & Troubleshooting 7-5 Troubleshooting MC75 Table 7-1 Troubleshooting the MC75 Problem MC75 does not turn on. Cause Solution Lithium-ion battery not charged. Charge or replace the lithium-ion battery in the MC75. Lithium-ion battery not installed properly. Install the battery properly. See Installing the Main Battery on page 1-6. System crash. Perform a warm boot. If the MC75 still does not turn on, perform a cold boot. See Resetting the MC75 on page 2-15. Battery failed.
7-6 MC75 User Guide Table 7-1 Troubleshooting the MC75 (Continued) Problem MC75 shuts off. Tapping the window buttons or icons does not activate the corresponding feature. A message appears stating that the MC75 memory is full. MC75 keeps powering down to protect memory contents. Cause Solution MC75 is inactive. The MC75 turns off after a period of inactivity. If the MC75 is running on battery power, set this period from 1 to 5 minutes, in one-minute intervals.
Maintenance & Troubleshooting 7-7 Table 7-1 Troubleshooting the MC75 (Continued) Problem The MC75 does not accept scan input. Cause Solution Scanning application is not loaded. Load a scanning application on the MC75. See the system administrator. Unreadable bar code. Ensure the symbol is not defaced. Distance between exit window and bar code is incorrect. Place the MC75 within proper scanning range. MC75 is not programmed for the bar code.
7-8 MC75 User Guide Table 7-2 Troubleshooting Bluetooth Connection (Continued) Problem Cause Solution Can’t make my Ericsson R520 phone discoverable. You attempted to bond with the phone, and when the phone presented a “pairing query,” you entered No. This prevents the phone from being discoverable until it is reset. Reset the phone by removing its battery. There is a delay in the Bluetooth stack re-initializing during a resume from suspend. This is normal behavior. No solution required.
Maintenance & Troubleshooting 7-9 Table 7-3 Troubleshooting the Single Slot USB/Serial Cradle (Continued) Symptom MC75 battery is not charging. Spare battery is not charging. During data communication, no data transmits, or transmitted data was incomplete. Possible Cause Action MC75 was removed from cradle or cradle was unplugged from AC power too soon. Ensure cradle is receiving power. Ensure MC75 is seated correctly. Confirm main battery is charging under Start > Settings > System > Power.
7 - 10 MC75 User Guide Four Slot Ethernet Cradle Table 7-4 Troubleshooting the Four Slot Ethernet Cradle Symptom Cause Solution During communication, no data transmits, or transmitted data was incomplete. MC75 removed from cradle during communications. Replace MC75 in cradle and retransmit. MC75 has no active connection. An icon is visible in the status bar if a connection is currently active. Battery is not charging. MC75 removed from the cradle too soon. Replace the MC75 in the cradle.
Maintenance & Troubleshooting 7 - 11 Table 7-5 Troubleshooting the Vehicle Cradle Symptom No data transmitted, or transmitted data was incomplete. Possible Cause Action MC75 removed from cradle during communication. Replace MC75 in cradle and retransmit. No null modem cable was used. Some external devices require a null modem cable. Retransmit using a null modem cable. Incorrect cable configuration. See the system administrator. Cable missing or disconnected. Re-connect cable.
7 - 12 MC75 User Guide Cables Table 7-7 Troubleshooting the Cables Symptom MC75 battery is not charging. During data communication, no data transmits, or transmitted data was incomplete. Possible Cause Action MC75 was disconnected from AC power too soon. Connect the power cable correctly. Confirm main battery is charging under Start > Settings > System > Power. The 3600 mAh battery fully charges in less than six hours. Battery is faulty. Verify that other batteries charge properly.
Maintenance & Troubleshooting 7 - 13 Table 7-8 Troubleshooting the Magnetic Stripe Reader (Continued) Symptom MC75 battery is not charging. During data communication, no data transmits, or transmitted data was incomplete. Possible Cause Action MC75 was removed from MSR or MSR was unplugged from AC power too soon. Ensure MSR is receiving power. Ensure MC75 is attached correctly. Confirm main battery is charging under Start > Settings > System > Power.
7 - 14 MC75 User Guide
Appendix A Technical Specifications MC75 Technical Specifications The following tables summarize the MC75’s intended operating environment and technical hardware specifications. MC75 Table A-1 MC75 Technical Specifications Item Description Physical Characteristics Dimensions Length: 17.9 cm (7.05 in.) Width: 8.4 cm (3.30 in.) Depth: 4.4 cm (1.70 in.) Weight 422 grams (14.90 oz) - with 3600 mAh battery 446g (15.70 oz) - with 4800 mAh battery Display Transflective color 3.
A-2 MC75 User Guide Table A-1 MC75 Technical Specifications (Continued) Item Description Notification Vibrator and LED Keypad Options 26 key numeric, 26 key Direct Store Delivery (DSD) numeric 44 key QWERTY, 44 key AZERTY, 44 key QWERTZ Audio Speaker, receiver, microphone, headset jack, software support for full duplex record and playback (stereo) Performance Characteristics CPU XScale™ Bulverde PXA270 processor at 624 MHz Operating System Microsoft® Windows Mobile™ 6.
Technical Specifications A-3 Table A-1 MC75 Technical Specifications (Continued) Item Description Operating Channels Chan 8-169 (5040 – 5845 MHz) Chan 1-13 (2412-2472 MHz) Chan 14 (2484 MHz) Japan only Actual operating frequencies depend on regulatory rules and certification agency Security WPA2, WPA, WEP (40 or 128 bit), TKIP, TLS, TTLS (MS-CHAP), TTLS (MS-CHAP v2), TTLS (CHAP), TTLS-MD5, TTLS-PAP, PEAP-TLS, PEAP (MS-CHAP v2), AES, LEAP Spreading Technique Direct Sequence Spread Spectrum (DSSS) a
A-4 MC75 User Guide Table A-1 MC75 Technical Specifications (Continued) Item Description Pitch Angle +/- 60° from normal Skew Tolerance +/- 50° from normal Ambient Light Total darkness to 9,000 ft.
Technical Specifications A-5 Table A-2 Data Capture Options (Continued) Item Description Imaging Decode Capability Code 39 Codabar Discrete 2 of 5 EAN-13 UPC/EAN supplementals Webcode Composite C Macro PDF-417 Data Matrix US Planet Canadian 4-state Chinese 2 of 5 microQR GS1 DataBar Limited GS1 DataBar Expanded Stacked Camera Decode Capability Code 39 Codabar Discrete 2 of 5 EAN-13 UPC/EAN supplementals Webcode Composite C Macro PDF-417 Data Matrix US Planet Canadian 4-state GS1 DataBar GS1 DataBar
A-6 MC75 User Guide MC75 Accessory Specifications Single Slot USB/Serial Cradle Table A-3 Single Slot USB/Serial Cradle Technical Specifications Feature Description Dimensions Length: 14.54 cm (5.72 in.) Width: 11.05 cm (4.35 in.) Height: 9.10 cm (3.58 in.) Weight 196 g (6.
Technical Specifications Table A-4 Four Slot Ethernet Cradle Technical Specifications (Continued) Feature Description Charging Temperature 0°C to 40°C (32°F to 104°F) Humidity 5% to 95% non-condensing Drop 76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature Electrostatic Discharge (ESD) +/- 15 kV air +/- 8 kV contact Four Slot Charge Only Cradle Table A-5 Four Slot Charge Only Cradle Technical Specifications Feature Description Dimensions Length: 46.80 cm (18.42 in.
A-8 MC75 User Guide Table A-6 Four Slot Battery Charger Technical Specifications (Continued) Feature Description Power Consumption 30 watts Operating Temperature 0°C to 50°C (32°F to 122°F) Storage Temperature -40°C to 70°C (-40°F to 158°F) Charging Temperature 0°C to 40°C (32°F to 104°F) Humidity 5% to 95% non-condensing Drop 76.2 cm (30.0 in.
Appendix B Voice Quality Manager Introduction The Voice Quality Manager (VQM) is a software package that resides on the MC75. VQM enables a set of features for Voice over WiFi (VoWiFi) calls, and a sub-set of those features for cellular line (GSM or CDMA) calls. The VQM user interface is designed to be intuitive and easy to use, so complex tasks such as enabling the Acoustic Echo Canceller (AEC) while a call is in progress are done with very little or no user intervention.
B-2 MC75 User Guide Audio Modes The MC75 can be in any one of the seven different audio modes. The mode is visually indicated by the VQM icon on the title bar. VQM icon Figure B-1 VQM Icon in Title Bar The VQM icon indicates that the device is in speakerphone mode without Acoustic Echo Cancellation (indicated by the gray VQM icon). The audio modes and their corresponding VQM title bar icons are: Table B-1 VQM Icons Icon Description Speakerphone with Acoustic Echo Cancellation.
Voice Quality Manager B-3 The table below lists the current audio mode and the subsequent audio mode after tapping the VQM icon. Table B-2 Changing Audio Modes Audio Mode before Tapping VQM Icon Audio Mode after Tapping VQM Icon Speakerphone Handset Handset Speakerphone Wired headset Wired headset Bluetooth headset Speakerphone If the audio mode is set to speakerphone and the user taps the VQM icon, the audio mode changes to handset.
B-4 MC75 User Guide Voice Packet Prioritization IP soft phones transmit voice packets in the same manner as any other application that sends data over the network. On a network with different types of traffic, voice packets are given the same priority as any other traffic, and therefore may be subject to delays. WiFi Multi-media (WMM) is a solution to this problem. WMM is a specification that supports prioritizing traffic, and “higher-priority” packets can be given preferential treatment.
Appendix C Windows Mobile 6.5 Introduction This chapter describes the new features in the latest version of the operating system OEM version with Windows Mobile 6.5. These include: • Finger scrolling functionality • New Home screen • New Start menu • New Lock screen • RS507 support • Battery Swapping • USB Configuration. Finger Scrolling Windows Mobile 6.5 adds finger scrolling capabilities to the display.
C-2 MC75 User Guide Status Bar Today Screen Tile Bar Open the Start Menu Tiles Figure C-1 Windows Mobile Home Screen Touch and hold the screen with your finger and move the Home screen up and down. As the application names move under the Information Status bar, information relevant to that application appear in the bar. Figure C-2 Moving Today Screen You can also touch and hold the Information Status bar and move it up and down over an application name.
Windows Mobile 6.5 C-3 Figure C-3 Moving Information Status Bar Application Icon Application Information Figure C-4 Information Bar Example > Settings > Today. On the horizontal scroll, use Appearance to customize To customize the Home screen, tap the background and the Items to change the display format. Classic Today Screen The user can change to the classic Today screen layout that is used in Windows Mobile 6.1.
C-4 MC75 User Guide Status Bar Today Screen Task Tray Tile Bar Figure C-5 Classic Today Screen To change to the classic view tap > Settings > Home > Items. Figure C-6 Home Screen Settings Deselect the Windows Default checkbox and select any of the other checkboxes. Tap . The task bar at the bottom of the screen can contain the task tray icons listed in Table C-1.
Windows Mobile 6.5 C-5 Table C-1 Task Tray Icons Icon Name Description Wireless connection status Wireless connection status icon. Indicates WLAN signal strength and opens the Wireless Applications menu. Bluetooth Enabled The Bluetooth Enabled icon appears in the task tray and indicates that the Bluetooth radio is on (Displays only if the StoneStreet One Bluetooth stack is enabled).
C-6 MC75 User Guide Table C-2 Status Bar Icons Icon Description Icon Description Notifications Indicates a reminder of an upcoming calendar event. Notification that one or more instant messages were received. Notification that one or more e-mail/text messages were received. Notification that one or more voice messages were received. There are more notification icons than can be displayed. Connectivity Connection is active. Connection is not active. Synchronization is occurring.
Windows Mobile 6.5 Table C-2 Status Bar Icons (Continued) Icon Description Icon Description 3G in use. (GSM only) GPRS connecting. (GSM only) GPRS in use. (GSM only) EGPRS connecting. (GSM only) EGPRS in use. (GSM only) EVDO connecting. (CDMA only) EVDO in use. (CDMA only) SIM Card not installed. (GSM only) All sounds are on. All sounds are off. Audio Vibrate is on. Battery Battery is charging. Battery has a full charge. Battery has a high charge. Battery has a medium charge.
C-8 MC75 User Guide Table C-3 Task Tray Icons Icon Name Description Magnify Enlarges the screen. Connectivity Displays the Connectivity dialog box. Phone Displays the Phone dialog box. Volume Displays the Volume dialog box. Power Displays the Power window. Clock & Alarms Opens the Clocks & Alarms window. Tile Bar The Tile Bar, located at the bottom of the screen, contains the Start tile displays tiles that vary depending upon the open application. to open the Start Menu.
Windows Mobile 6.5 C-9 Table C-4 Programs on the Start Screen Icon Name Description Icon Name Description Home Displays the Home screen. Text Send an SMS text message. Phone Make calls. E-mail Send an Email. Contacts Keep track of friends and colleagues. Calendar Keep track of appointments and create meeting requests. Internet Explorer Browse Web and WAP sites as well as download new programs and files from the Internet. Settings Open the Settings folder.
C - 10 MC75 User Guide Table C-4 Programs on the Start Screen Icon Name Description Icon Name Description Tasks Keep track of your tasks. File Explorer Organize and manage files on your device. ActiveSync Synchronize information between the MC75 and a host computer or the Exchange Server. Task Manager Enables viewing of memory and CPU allocations and stops running processes. Refer to the Microsoft Applications for Windows Mobile 6 User Guide for more information.
Windows Mobile 6.5 C - 11 Table C-4 Programs on the Start Screen Icon Name Description Icon Name Description Modem Link Enables the MC75 to be used as a modem. Rapid Deployment Client Facilitates software downloads from a Mobility Services Platform Console FTP server to the MC75. Refer to the MC75 Integrator Guide for more information.
C - 12 MC75 User Guide Table C-5 Setting Applications (Continued) Icon Name Microsoft My Phone Description Icon Name Description Synchronizes the phone’s contacts, calendar, tasks, text messages, music, photos, videos and other documents with your My Phone account at www.microsoft.com. Connections Folder Beam Set the MC75 to receive incoming IrDA beams.
Windows Mobile 6.5 C - 13 Table C-5 Setting Applications (Continued) Icon Name Description Icon Name Description Backlight & Keylight Set backlight and keylight settings. Customer Feedback Submit feedback on the Windows Mobile 6 software. Error Reporting Enable or disable the Microsoft’s error reporting function. Encryption Allow files on a storage card to be encrypted. Encrypted files are readable only on your device. External GPS Set the appropriate GPS communication ports, if required.
C - 14 MC75 User Guide Figure C-10 Volume Dialog Box 2. Tap and move the slide bar to adjust the volume. 3. Select the On or Off radio button to turn the volume on or off. NOTE Use can also adjust the system volume using the Sounds & Notifications window or by using the keypad. Battery Icons The Main Battery icon appears in the Title Bar when the Today screen is visible. The icon indicates the battery power level.
Windows Mobile 6.5 C - 15 Figure C-12 Connectivity Dialog Box Locking the MC75 You can lock the MC75 by disabling key presses and screen tap or by requiring a password. NOTE You can make emergency calls even when the MC75 is locked. Locking the MC75 turns off keyboard and touch screen functionality. This is helpful when the MC75 is turned on and you want to prevent accidental key presses. To lock the device, tap > . Locking without PIN or Password When the MC75 is locked, the Lock screen appears.
C - 16 MC75 User Guide Locking with Simple PIN When the MC75 is locked, the Lock screen appears. Figure C-14 Lock Screen Drag to either the right or left side of the screen. Enter the PIN and then tap Contacts window, tap to unlock and display the Home screen, tap to unlock and display the Messaging window. Figure C-15 Simple PIN Password Window Locking with Strong Password When the MC75 is locked, the Lock screen appears.
Windows Mobile 6.5 C - 17 Figure C-16 Strong Password Lock Screen Enter the strong password and then tap Unlock. Password Locking Setup Use the Password window to set a password to disable unauthorized access to the MC75. NOTE 1. Tap If the device is configured to connect to a network, use a strong (difficult to figure out) password to help protect network security. Password cracking tools continue to improve and the computers used to crack passwords are more powerful than ever.
C - 18 MC75 User Guide a. Enter a seven character password in the Password: field. A strong password must contain at least seven characters and contain at least three of the following: uppercase and lowercase letters, numerals, and punctuation. b. Re-enter the password in the Confirm: field. 6. Tap 7. In the horizontal scroll, select Hint. Enter a hint to remember the password if you forget it. 8. Tap 9. In the text box, enter a hint for a password reminder. 10. Tap . . .
Windows Mobile 6.5 C - 19 Figure C-18 PowerKey Action Window 3. Tap Safe Battery Swap icon. 4. Wait for the red decode LEDs to turn on and then turn off. 5. Remove the battery. Suspend Mode To place the MC75 in suspend mode: 1. Press the red Power button to suspend the MC75. The Power Key Action screen appears. Figure C-19 PowerKey Action Window 2. Tap Suspend icon. 3. The MC75 goes into suspend mode. Assisted GPS GPS can be used in stand-alone or Assisted GPS (A-GPS) modes.
C - 20 MC75 User Guide would ordinarily have to download from the GPS satellites and other aiding data that helps the acquisition. With the A-GPS data, GPS receivers can operate faster and more reliably. A-GPS follows the Secure User Plane Location (SUPL) protocol which allows the MC75 to communicate with a location server. To configure SUPL on the MC75: 1. Tap Start > Settings > System > GPS Setup icon. Figure C-20 SUPL Setup Tab 2.
Windows Mobile 6.5 C - 21 Figure C-21 MISC Tab Smart Re-Aiding causes the MC75 to reconnect to the SUPL server and download new A-GPS data if there are satellites in view and the number of satellites in use fall below the SVLimit value and the length of time passed since the last SUPL session is more than the value set in the Interval field. Timing Control on Opening determines whether a SUPL session is established when the GPS port is opened.
C - 22 MC75 User Guide Figure C-22 Start Screen Settings Tab 3. Select the number of columns. 4. Tap OK. NOTE Tap Reset to return to the default 3 Column setting. 5. Tap OK. 6. Preform a warm boot. IE Zoom Mapping With Windows 6.5, when Internet Explorer opens the volume keys on the side of the MC75 are used to zoom in and out. To disable IE Zoom Mapping: 1. Tap Start > Settings > System > UI Settings. 2. Tap the IE Zoom Mapping tab. Figure C-23 IE Zoom Mapping Tab 3. Select Off. 4. Tap OK.
Windows Mobile 6.5 C - 23 5. Tap OK to turn off mapping.
C - 24 MC75 User Guide
Glossary A API. An interface by means of which one software component communicates with or controls another. Usually used to refer to services provided by one software component to another, usually via software interrupts or function calls Aperture. The opening in an optical system defined by a lens or baffle that establishes the field of view. Application Programming Interface. See API. ANSI Terminal. A display terminal that follows commands in the ANSI standard terminal language.
Glossary - 2 MC75 User Guide Bar Width. Thickness of a bar measured from the edge closest to the symbol start character to the trailing edge of the same bar. BIOS. Basic Input Output System. A collection of ROM-based code with a standard API used to interface with standard PC hardware. Bit. Binary digit. One bit is the basic unit of binary information. Generally, eight consecutive bits compose one byte of data. The pattern of 0 and 1 values within the byte determines its meaning. Bits per Second (bps).
Glossary - 3 Codabar. A discrete self-checking code with a character set consisting of digits 0 to 9 and six additional characters: (“-”, “$”, “:”, “/”, “,” and “+”). Code 128. A high density symbology which allows the controller to encode all 128 ASCII characters without adding extra symbol elements. Code 3 of 9 (Code 39). A versatile and widely used alphanumeric bar code symbology with a set of 43 character types, including all uppercase letters, numerals from 0 to 9 and 7 special characters (“-”, “.
Glossary - 4 MC75 User Guide Device Configuration Package. The Symbol Device Configuration Package provides the Product Reference Guide (PRG), flash partitions, Terminal Configuration Manager (TCM) and the associated TCM scripts. With this package hex images that represent flash partitions can be created and downloaded to the mobile computer. Discrete Code. A bar code or symbol in which the spaces between characters (intercharacter gaps) are not part of the code. Discrete 2 of 5.
Glossary - 5 H Hard Reset. See Cold Boot. Hz. Hertz; A unit of frequency equal to one cycle per second. Host Computer. A computer that serves other terminals in a network, providing such services as computation, database access, supervisory programs and network control. High-Speed Downlink Packet Access (HSDPA).
Glossary - 6 MC75 User Guide accepts “packets” from the layer 4 transport protocol (TCP or UDP), adds its own header to it and delivers a “datagram” to the layer 2 data link protocol. It may also break the packet into fragments to support the maximum transmission unit (MTU) of the network. IP Address. (Internet Protocol address) The address of a computer attached to an IP network. Every client and server station must have a unique IP address. A 32-bit address used by a computer on a IP network.
Glossary - 7 MDN. Mobile Directory Number. The directory listing telephone number that is dialed (generally using POTS) to reach a mobile unit. The MDN is usually associated with a MIN in a cellular telephone -- in the US and Canada, the MDN and MIN are the same value for voice cellular users. International roaming considerations often result in the MDN being different from the MIN. MIL. 1 mil = 1 thousandth of an inch. MIN. Mobile Identification Number.
Glossary - 8 MC75 User Guide PC Card. A plug-in expansion card for laptop computers and other devices, also called a PCMCIA card. PC Cards are 85.6mm long x 54 mm wide, and have a 68 pin connector. There are several different kinds: Type I; 3.3 mm high; use - RAM or Flash RAM Type II; 5 mm high; use - modems, LAN adaptors Type III; 10.5 high; use - Hard Disks PCMCIA. Personal Computer Memory Card Interface Association. See PC Card. Percent Decode.
Glossary - 9 RS-232. An Electronic Industries Association (EIA) standard that defines the connector, connector pins, and signals used to transfer data serially from one device to another. S Scan Area. Area intended to contain a symbol. Scanner. An electronic device used to scan bar code symbols and produce a digitized pattern that corresponds to the bars and spaces of the symbol.
Glossary - 10 MC75 User Guide Symbol. A scannable unit that encodes data within the conventions of a certain symbology, usually including start/stop characters, quiet zones, data characters and check characters. Symbol Aspect Ratio. The ratio of symbol height to symbol width. Symbol Height. The distance between the outside edges of the quiet zones of the first row and the last row. Symbol Length.
Glossary - 11 U UDP. User Datagram Protocol. A protocol within the IP protocol suite that is used in place of TCP when a reliable delivery is not required. For example, UDP is used for real-time audio and video traffic where lost packets are simply ignored, because there is no time to retransmit. If UDP is used and a reliable delivery is required, packet sequence checking and error notification must be written into the applications. UPC. Universal Product Code. A relatively complex numeric symbology.
Glossary - 12 MC75 User Guide
Index Numerics 1-D bar codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34 2-D bar codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34 A accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 auto charge cable . . . . . . . . . . . . . . . . . . . . . . . . 1-3 cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3, 6-24 charge cable . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 2 MC75 User Guide charging indicators . . . . . . . . . . . . . . . . . . . . . . 6-10 battery chargers communication/charge cables . . . . . . . . . . . . . 6-24 LED indicators . . . . . . . . . . . . . . . . . . . . . . 6-25 four slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9 battery charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 communication/charge cables . . . . . . . . . . . . . 6-24 using four slot battery charger . . . . . . . . . . . . . .
Index - 3 scan angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35 scan button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32 scan range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35 scanning . . . . . . . . . . . . . . . . . . . . . 2-35, 2-36, 2-37 two dimensional bar codes . . . . . . . . . . . . . . . . 2-34 deleting Bluetooth bond . . . . . . . . . . . . . . . . . . . . . . 4-22 DEX cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 4 MC75 User Guide battery status . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14 charging . . . . . . .2-14, 6-3, 6-4, 6-5, 6-8, 6-10, 6-25 indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14 radio status . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14 scan and decode . . . . . . . . . . 2-14, 2-36, 2-37, 2-38 lithium-ion battery . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 locking MC75 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 5 security Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 serial charge cable . . . . . . . . . . . . . . . . . . . . . .1-3, 6-24 service information . . . . . . . . . . . . . . . . . . . . . . . . . . xviii settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 about . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8, C-12 backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 beam . . . . . . . . . . . . . .
Index - 6 MC75 User Guide warm boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-15, 4-4 Windows Live . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7, C-9 Windows Live Messenger . . . . . . . . . . . . . . . . . 2-7, C-9 wired headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-13, 5-2 Wireless Manager . . . . . . . . . . . . . . . . . . . . . . .1-13, 5-2 wireless manager . . . . . . . . . .
Motorola, Inc. One Motorola Plaza Holtsville, New York 11742, USA 1-800-927-9626 http://www.motorola.com/enterprisemobility MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2010 Motorola, Inc. All rights reserved.
