MICOM-2ES/2RS/2TS ALE HF-SSB TRANSCEIVERS Support for MIL-STD-188-141B Supplement to Owner’s Guide best radio for worst events IMRMB008
COMMERCIAL WARRANTY (STANDARD) Motorola radio communications products are warranted to be free from defects in material and workmanship for a period of ONE (1) YEAR, (except for crystals and channel elements which are warranted for a period of ten (10) years) from the date of shipment.
COMPUTER SOFTWARE COPYRIGHTS The Motorola products described in this instruction manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including the exclusive right to copy or reproduce in any form the copyrighted computer program.
best radio for worst events MICOM-2ES/2RS/2TS ALE HF-SSB TRANSCEIVER ALE Support for MIL-STD-188-141B Motorola 1720 West Paul Dirac Drive, Tallahassee 32310 FL, USA Supplement to Owner’s Guide Cat. No.
Warnings, Cautions and Notes Warnings, Cautions and Notes The following notations are used to place special emphasis on procedures, or to call attention to precautionary measures. An operating procedure, practice and so forth, which if not followed correctly, could result in personal injury, or loss of life. Warning An operating procedure, practice and so forth, which if not followed correctly, could result in damage to, or destruction of equipment.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Information for Safe, Efficient Operation Product Safety and RF Exposure for Mobile Two-Way Radios Installed in Vehicles or as Fixed Site Control Stations Caution BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS.
Warnings, Cautions and Notes Federal Communication Commission Regulations The FCC has established limits for safe exposure to radio frequency (RF) emissions from mobile two-way radios. The FCC requires manufacturers to demonstrate compliance with RF exposure limits before mobile two-way radios can be marketed In the U.S. When two-way radios are approved for occupational/controlled environment exposure limits, the FCC requires users to be fully aware of, and exercise control over, their exposure.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Compliance and Control Guidelines and Operating Instructions for Mobile Two-Way Radios Installed in Vehicles To control your exposure and ensure compliance with the occupational/controlled environment exposure limits, always adhere to the following procedures: • To transmit (talk), push the Push-To-Talk (PTT) button; to receive, release the PTT button.
Warnings, Cautions and Notes Electromagnetic Interference/Compatibility Note Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise configured for electromagnetic compatibility.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Operational Warnings For Vehicles with an Air Bag Warning Do not mount or place a mobile radio in the area over an air bag deployment area. Air bags inflate with great force. If a radio Is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle.
Table of Contents Table of Contents Page Introduction .................................................................................................... 1 Menu Updates................................................................................................. 1 New ALE Features ......................................................................................... 6 Selective Calling ....................................................................................... 6 ALE Addressing Method ...
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide viii ________________________________________________________________________________________________
Introduction Introduction This Supplement to the “MICOM-2E/2R ALE HF-SSB Transceivers Owner’s Guide”, Publication 68P02952C60-A, provides you with information on the full support for ALE in accordance with the MIL-STD-188-141B (previous versions supported only MIL-STD-188-141A). This new feature is available only on new versions (Version CK) of the MICOM-2E/2RS/2TS ALE HF-SSB transceivers (which are described in the “Supplement to Owner’s Guide”, Publication 6886872J01).
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide CH Mode MORE BAND LSB USB SQ ON OFF MORE PWR DSP CLAR NF MODE LOW MED HIGH MAX .. -200 . .. ... OFF .. .. .. .. +200 AGC SSB AME PLT SLOW FAST OFF ... BW 2.1 2.7 3.0 3.3 LSM CW .. .. ON OFF ON OFF ON OFF CLIP NB ATTN Only for ALE ... MORE RCLV GPS Note 1 Note 2 CALL SEND PAGE LQA MON BDIR SOUND ON OFF MORE MULT ALL NET Notes 1.
Menu Updates FREQ Mode MORE T/R SMPX DPLX RXO TXO BAND LSB USB DSP SQ ON OFF MORE PWR CLAR . -200 .. ... . . .. OFF . .. ... +200 NF .. .. CLIP ON OFF NB ON OFF ON OFF ATTN Frequency Change −−> <−− ... MORE RCLV Note 1 STOR BACK CLR MODE LOW MED HIGH MAX AGC SSB AME PLT SLOW FAST OFF ... BW 2.1 2.7 3.0 3.3 LSM CW Notes 1. The RCLV item appears only if the received signal level display is not permanently enabled using MENU>PROG>RAD>PRMT>RCLV. 2.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide PROG Menu RAD LANG ALE . . .. CHAN ENGLISH FRENCH ESPA PRMT OPTS ACC ALE AMP TUNE NON YES NO MORE BAUD 1.2 2.4 4.8 9.6 DPWR LOW MED HIGH MAX MST YES NO AST MORE PTBP YES NO KBBP YES NO YES NO TONE LOW HIGH ADT .. .. . 1 .. .. . STOR CW YES NO 10 ERAS PWR LOW MED HIGH MAX 0.25 0.5 0.8 RCLV YES NO DIM YES NO MORE MORE GET ATTN FREQ BAND SMPX DPLX RXO TXO LSB USB MODE SSB AME PLT AGC SLOW FAST OFF BW 2.1 2.7 3.0 3.
Menu Updates PROG Menu LANG ALE RAD . . . . ENGLISH FRENCH ESPA MORE NET RCV DIR OPT AMD AUTO STOR YES NO ADDR AMD EDIT ERAS MORE ADD MORE PTOT MLQA 1 .. .. . . .. .. 10 0 . . .. .. .. .. 100 ERAS EXAL YES NO . . .. . ERAS SAVE --> CLR SAVE YES NO ALL BDLK YES NO YES NO ANY YES NO YES NO WILD AADR YES NO YES NO ALL AUTO 0 . . .. .
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide New ALE Features This section covers the new ALE features that meet the requirements of MIL-STD-188-141B. This includes a description of selective calling features, and operating instructions for the various types of ALE calls. This includes new call types, as well as call types already supported under MIL-STD-188-141A but have been expanded under new version.
New ALE Features In the following sections, “A,” “B,” “C” or “D” indicates any alphanumeric character other than “@” or “?”. Note MICOM 2 has the capacity to store and use 100 addresses of up to 15 characters each. MICOM 2 will reject addresses longer than 15 characters, and will notify you with an UFA WRONG message. Address and Call Types ALE stations, including the MICOM 2, have the capability and flexibility to link with one or many prearranged or as-needed single or multiple stations.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Table 1. Use of “@” Stuffing Symbol (Cont.
New ALE Features • A receiving station will accept a wildcard character as a substitute for the alphanumeric character in its own address that occupies the same position. This means that the wildcard character is a substitute for any of 36 characters and digits (A to Z, 0 to 9) in the Basic 38 character subset. • Multiple wildcard characters can be used in different positions of the same address (basic or extended). See Table 2 for examples of patterns using the “?” wildcard symbol. Table 2.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Table 2. Use of “?” Wildcard Symbol (Cont.
New ALE Features AnyCalls An AnyCall is a general broadcast similar to AllCall with the difference that it requests responses, without designating any specific addressee(s). Therefore, an ALE station may use the AnyCall to generate responses from essentially unspecified stations, and thus it can identify new stations and connectivities. The global AnyCall address is @@?.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Using the MultiNet Feature Normally, a radio operating in the ALE mode receives and transmits only in its currently selected net. However, there are operational scenarios in which it is beneficial to enable radios to use the ALE functions while still being aware of what is going on in additional nets (for example, firefighters and paramedics must often respond to the same emergency), and be able of answering a call in another net.
New ALE Features Messages The ALE enables you to create, send or receive alphanumeric messages (“paging” messages) in accordance with the AMD (Automatic Display Message) definition in Federal Standard FS-1045. The messages are displayed on the receiving station LCD display, and can be up to 90 characters long. Messages can be added to any type of call, whether individual, group, net, AllCall, AnyCall, bidirectional handshake, etc.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Entering the ALE Mode To use the ALE mode, first it must be enabled as explained below. Enabling the ALE Mode ➤ To enter the ALE mode: 1. Press MENU to display the Menu screen. If you see SCAN next to F3, first enable the ALE functionality using PROG>RAD>OPTS>ALE. MOTOROLA MENU CHAN FREQ ALE BITs Note MOTOROLA 2. Press ALE (F3). The last active net flashes in the display. ALE NET 7 3. To use the displayed net, press ENTER.
New ALE Features • Up to 100 ALE addresses in the directory • Up to 100 scan channels • Up to 12 AMD (paging) messages. All the ALE features you can use on your radio can be programmed: to program or modify features, you can use the front panel of the radio, as described in the ALE Programming section. Some of the ALE features can also be preprogrammed using the RSS, but the RSS does not support most of the new ALE features per MIL-STD-188-141B.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Receiving and Transmitting Calls in ALE Mode Note The information appearing in this section updates the ALE operating instructions presented in previous publications. Therefore, if your radio set supports MIL-STD-188-141B, use only the ALE operating instructions appearing in this Supplement. The MICOM 2 supports the following types of ALE calls in accordance with MIL-STD-188-141B: • Individual call – call directed to a specific station.
New ALE Features Receiving Calls in ALE Mode When your MICOM 2 receives a call, it displays its type and the source address. You are also notified when a message is attached: if a message is received, the name of the calling station is preceded by an exclamation mark. MOTOROLA FROM !ABC For any type of call, if the ALERT attribute is programmed to YES, you will hear the alert tone when a message is received. ➤ Receiving an individual call: When an individual call (i.e.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide ➤ Receiving an AnyCall: You can program your radio to ignore incoming AnyCalls. If the radio is set to ignore incoming AnyCalls, it stops scanning when an AnyCall is received but it does not display, nor lets you hear Note the call. At the end of the AnyCall, the radio automatically returns to the scanning mode. MOTOROLA ALE ANYCALL When an AnyCall is received, the display flashes an AllCall alert that alternates ANYCALL with the calling station name.
New ALE Features If the received call includes a message, an exclamation mark precedes the station name, and the name is followed by a colon and the message. If the calling station name and message are too long and do not fit in the display, press <-> (F3) to enter the View mode, where you can scroll right and left to display the whole message. MOTOROLA FROM !ABC:PACK CALL LQA MON MOTOROLA FROM !ABC:PACK CALL LQA <--> MONs ➤ To display LQA for the received call: Press LQA (F2).
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide LQA (F3) displays the channel on which the link was established, and the LQA score of the current link. • Notes MON (F4) If the name of the station you are linked to is not in your directory, this function will not be available. • The LQA (F3) key is displayed only if you established the link in the ALE mode (in the Channel mode, this function is not available, because the call is received/transmitted on the current channel).
New ALE Features MORE PWR (MORE, MORE, F1) MODE (MORE, MORE, F2) AGC (MORE, MORE, F3) BW (MORE, MORE, F4) selects the transmit power level (LOW, MED, HIGH or MAX). selects the operation mode (SSB, AME or PLT). controls the automatic gain control function (fast/slow/off). selects the filter bandwidth, MORE displays the receive level while F1 is pressed. RCLV (MORE, MORE, MORE, F1) FREQ (MORE, MORE, MORE, F2) displays the current frequency while F2 is pressed.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Using the Caller Stack The caller stack stores information about unanswered calls. The stack entry contains the self-address of the calling station, and any message sent by the calling station when it sent the call set up request. The stack can contain up to 10 calls. The radio records an address in the stack only once, even if the same caller made several unanswered calls.
New ALE Features ➤ To remove an address from the stack: The radio automatically removes an address from the stack in the following cases: • When the operator calls a station registered in the caller stack, all stack calls containing that address are erased from the stack, regardless of whether the call was returned from within the stack or during an individual call. • The stack can contain up to ten addresses.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Transmitting Calls in ALE Mode To transmit an ALE call, you must specify the destination. In general, the destination consists of a net and one or more stations (members of the specified net): • When the MultiNet function (page 12) is disabled, the destination net is always the currently selected net (its number is displayed on the LCD while the radio is scanning).
New ALE Features Calls to an Individual Station ➤ To transmit an individual call with MultiNet OFF: 1. Press CALL (F1). The radio displays the last called address. This may be a station address, or any other type of address (for example, net, wildcard, etc.). MOTOROLA CALL 1001 SEND PAGE CHAN MONs 2. To select a different station: MOTOROLA Press the UP/DOWN keys to scroll between stations.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide 5. After the link is established, you will see a LINK message. Now you may press the PTT and start talking. MOTOROLA LINK 1234 SEND PAGE CHAN MONs If the link with the selected station cannot be set up, you will see for a few seconds a flashing NO LINK message. Note 6. To disconnect the link, press the ESC key. If you want to call again the same station, double-press the PTT to use the quick-call feature (see page 28).
New ALE Features 6. After the link is established, you will see a LINK message. Now you may press the PTT and start talking. 7. To disconnect the link, press the ESC key. ➤ To transmit on a specific channel: MOTOROLA 1. Initiate a call as explained above (page 25 or 26) and select the desired station. 2. Press CHAN (F3) to select a specific channel. The channel with the best LQA score is displayed. The speaker is unmuted to enable you to check the channel quality by listening to it.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide While the radio is initializing the link, you can press STOP (F1) or ESC to abort the entire process. Note 6. After the link is established, you will see a LINK message. Now you may press the PTT and start talking. 7. To disconnect the link, press the ESC key. Quick Call A quick call is a call to the last station you tried to call (regardless of whether the call was successful or not).
New ALE Features Using Autodial The Autodial feature lets you use a single digit to call a preprogrammed address. There are ten programmable Autodial addresses, where each can include a message. See Auto Dial Parameters on page 61 for details on programming the Autodial list. ➤ To use Autodial to send a call: MOTOROLA 1. Press # on the keypad. CALL SELECT#_ If you do not select an auto-address within a few seconds, the display automatically reverts to the previous state. Note 2.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide 6. After the link is established, you will see a LINK message. Now you may press the PTT and start talking. 7. To disconnect the link, press the ESC key. Sending Messages You can send messages (page) together with the initial call (before the link is set up), and also whenever necessary while the link is already set up (that is, when your station is in a link with the destination station).
New ALE Features ➤ To send a message during a call (link state): 1. Press PAGE (F2). If this function key is not displayed, you cannot send a message in the present mode. MOTOROLA LINK 1009 SEND PAGE CHAN MONs Note 2. Select or edit the desired message as explained on page 29. MOTOROLA 3. Press SEND (F1) or ENTER to send the message. 4. The radio now starts the link set up process for this message (this process is similar to the process used to set up the link for this call).
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Other Types of Calls In addition to calls to individual stations described on the pages 24 to 30, additional types of calls can be used to help you call multiple stations (see list on page 16). A properly designed address assignment plan is needed to take advantage of the special ALE calling modes. Note The special call types are reached under a special submenu, designated MULT (see Figure 6 for its organization). ➤ To select a special call type: 1.
New ALE Features Option Capabilities See Page … Group call – call directed to a group of individually selected 38 GRP stations. Groups can be preprogrammed, but you can also select the stations to be called and save the selection for reuse. Up to five groups can be defined. AnyCall – call directed to all the other stations 41 ANY simultaneously, usually used to detect new stations.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide ➤ To send global AllCall using the ESC key: MOTOROLA 1. Press ESC continuously for a few seconds. The radio starts sending the GL AllCall. During this process, you will see TO alternating with the number of the channel on which the set up request is being sent. TO GL ALLCALL STOP NET GRP ANYs MOTOROLA CH 2 GL ALLCALL STOP NET GRP ANYs While the radio is initializing the link, you can press STOP (F1) or ESC to abort the entire process.
New ALE Features ➤ To send selective AllCall: MOTOROLA 1. Press CALL (F1). The radio displays the last called address. CALL 1001 SEND PAGE CHAN MONs MOTOROLA 2. Press MORE once. CALL GL ALLCALL MULT PAGE CHAN MONs GRP ANYs MOTOROLA 3. Press MULT (F1) to display the first page of special calls. CALL ALL NET MOTOROLA 4. Press ALL (F1). CALL GL ALLCALL 5. Press SEL (F4). If you decide to send a Global AllCall, press GLOB (F3).
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide MOTOROLA 9. After a delay, you will see LINK, and you can start talking. LINK SL ALLCALL SEND PAGE GLOB MONs 10. Press PAGE (F2) if you want to send a message. See page 31 for details. MOTOROLA 11. To end the call, press ESC.
New ALE Features Transmitting Net Calls Before starting, select the net you want to use as explained on page 24. However, when MultiNet is enabled, you will be prompted for a net number as soon as you start a call. Note • You can program nets using the front panel, or the RSS. • The radio must be programmed as a MASTER radio in the net (an ALE Programming option) in order to be able to transmit net calls. ➤ To transmit a net call: 1. Press CALL (F1). The radio displays the last called address.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Transmitting Group Calls Group calls let you call several individual stations in your net (at least 2) at once. Thus, you can use a group call to communicate with a few select stations, while other stations can still communicate at will, using other channels available to your net. You can call up to 5 stations in a group call. The only restriction is that the total length of all the addresses cannot exceed 12 ALE words (36 characters).
New ALE Features ➤ To transmit a group call: 1. Press CALL (F1). CALL The radio displays the last called address. 1001 If you see the group you want, skip directly to Step 6 SEND PAGE CHAN MONs below, otherwise continue as explained below. 2. Select the GRP option as explained on page 32. 3. The first group displayed is always group 1. If this is the group you want, skip directly to Step 6 below, otherwise press the UP or DOWN arrows until you see the desired group. 4.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide ➤ To define or change a group: 1. Press CALL (F1) and select the GRP option, as you do to start a group call (page 38). 2. The first group displayed is always group 1. If this CALL is the group you want, skip directly to Step 3 below, GRP 1 otherwise press the UP or DOWN arrows until you SEND PAGE CHAN SELs see the desired group. 3. To select the stations you want in this group, press SEL (F4).
New ALE Features As you scroll through the directory, you will see DIR for stations that can be added, and ADDED for those already added. If the station you want to add to the group is not in the directory: !" Enter the new station using the keypad. If you make a mistake, scroll to the desired position using <-- (F2) and/or --> (F3), or clear (CLR (F4)) the whole entry and start again. !" When ready, press SAVE (F1) to store the new station in the directory.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide • Double selective: similar to selective, except that you specify the last two characters of the address. To make an AnyCall, first you must select the address to be used for the call. MICOM-2 will wait for responses for a certain time before entering the link state with all the stations that responded within this interval (the maximum number of stations that are accepted in an AnyCall is 16).
New ALE Features 6. Select the AnyCall address: MOTOROLA • To send a general AnyCall, press ? (F1). • To send a selective AnyCall, enter the desired character (any character except #, @ or ?). ALL ENDING:_ ? PAGE CHAN CLR MOTOROLA ALL ENDING:1_ ? <-- CHAN CLR MOTOROLA • ALL ENDING:59 To send a double-selective AnyCall, enter two characters. ? <-- CHAN CLR 7. Confirm your selection by pressing ENTER (see below examples for the 3 types of addresses).
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Transmitting Wildcard Calls Wildcard calls, that is, calls in which the destination address includes the wildcard character ?, let you to simultaneously address multiple stations with a single address: • Any station receiving an address with wildcards stops scanning and checks the address length: if the number of characters in the received address is different from the number of characters in its own self-address, the station ignores the call.
New ALE Features MOTOROLA 4. Press MORE again to display the next page. CALL WILD SELF GRP ANYs CHAN SELs MOTOROLA 5. Press WILD (F1) to start. CALL WILD 6. Press SEL (F4). WILD _ SEND PAGE MOTOROLA Note ? PAGE CHAN MONs If you try to send (SEND (F1)) the call without first selecting an address, your attempt is rejected and you see for a few seconds NOT PROG. 7. Select the desired address: • To insert a wildcard, press ? (F1).
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide MOTOROLA 12. After a delay, you will see LINK with the wildcard address flashing. LINK ?135? 13. Confirm the link set up by pressing ENTER or the PTT. The address stops flashing, and you can start talking. LINK ?135? SEND PAGE LQA MONs LQA MONs MOTOROLA SEND PAGE MOTOROLA 14. To end the call, press ESC. END CALLING Transmitting a Self Call The self-call is a test call addressed to your own address within the currently selected net.
New ALE Features MOTOROLA 5. Press SELF (F2) to start the self-call. 6. You may select now a specific channel to perform the call, by pressing CHAN (F1). See details on page 27. 7. When ready, press SEND (F1) to start transmitting. The display alternates between your self-address and the channel used for the call is sent. If you did not select a specific channel, the channel number changes as the radio sends the call on each channel assigned to the selected net.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Note Before starting, you may want to select a different net to use: see instructions on page 24. When MultiNet is enabled, you will be prompted for a net number as soon as you press CALL (F1) to start a call. ➤ To execute a bidirectional handshake with an individual station: MOTOROLA 1. Press LQA (F2) to enter the LQA menu. 2. Press BIDR (F1). The last called address is displayed. If this is the address you want, skip directly to Step 6 below.
New ALE Features During the bidirectional handshake process, you can press STOP (F1) or ESC to abort the entire process. Note ➤ To execute a bidirectional handshake with a net: MOTOROLA 1. Press LQA (F2) to enter the LQA menu. 2. Press BIDR (F1). The last called address is displayed. If this is the net you want, skip directly to Step 8 below. LQA BDIR SOND CHAN OK s CHAN OK s CHAN OK s CHAN OK s CHAN OK s MOTOROLA BDIR 1001 SEND PAGE MOTOROLA 3. Press MORE. BDIR 1001 4.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Sounding Sounding is used to test the quality of the channels and propagation paths of all channels in the net. The sounding signal is normally repeated automatically, at regular intervals. A complete round of sounding messages, or "sounding cycle" can be programmed to 30, 60, 90, or 120 minutes, or can be set to OFF. Sounding can also be initiated manually whenever necessary, even if automatic sounding is enabled.
New ALE Features Using the Inlink Function When the inlink function is enabled (see instructions in the ALE Options Configuration section starting on page 59), the DISC 1001 stations participating in a call are automatically notified by a RCLV PAGE LQA MONs DISC message whenever another participant leaves (disconnects from) the call. The link is then automatically disconnected when only one station is left (that is, after all the other participants disconnected).
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Transmitting ALE Calls in the Channel Mode The ALE option is available in both the ALE and Channel modes and therefore, the radio can also answer ALE calls. The transmission process is similar for both operating modes, with the following differences: • In the Channel mode, every call is initiated on the currently selected channel.
ALE Programming ALE Programming This section provides concise instructions for using the ALE Programming mode. This mode, reached under the PROG menu (see Figure 4 and Figure 5) is used to configure the parameters needed by the ALE function. The ALE parameters are identified in Figure 5. The Programming mode is accessible only if the radio is not locked.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide • DIR • AMD Description Directory: configuration of the ALE address list. See Page … 58 Messages: preparation of AMD messages to be sent with ALE calls. 58 You can also edit, or prepare a new message, on-line. Note • OPT • AUTO • STOR Important Options: configuration of the various ALE options, such as PTT timeout, external alarm, and so on. Autodial parameters: shortcuts for ALE calls to frequently called stations.
ALE Programming • NAME Edit the net name and the self-address: • NET: Define or edit the net names. It is not allowed to use a name already used as a self-address, nor an address already appearing in the address directory. • • MEMB • CHAN SELF: Define or edit your self address (the identification of your station, to be used by other stations within the same net). It is not allowed to use a name already used as a net address, nor an address already appearing in the address directory.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide • OPT • GET • ERAS Configure net options, including: sounding, silent network, LQA request, scan rate, home acknowledgment, monitor acknowledgment, occupancy detection, master/slave definitions, AllCall options and tune time. Copy all parameters from one network to another.
ALE Programming Setting the Net Options Use this menu to configure net options. The following sections explain the purpose of the net options. For detailed instructions, refer to Part II of this manual. • SOND Sounding Parameters: define the interval (in minutes) at which automatic sounding is performed (30, 60, 90 or 120 minutes), or define sounding as a manual function. See Sounding on page 50 for a detailed explanation on the sounding process.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide • TUNE Tune Time: select the tuning time. Tuning time is the maximum time the current ALE waits for the called station to tune (this is the tune-in time of the slowest tuner in the net). The tune time is added to the calculated response time. Tune time can be 1 to 20 seconds, or OFF (zero). Directory Parameters This DIR option on the ALE Programming menu enables preparing the ALE address list.
ALE Programming ALE Options Configuration This menu enables you to configure the following ALE options: • PTOT PTT Timeout: the time (in minutes) which elapses between the moment you release the PTT button, until the ALE disconnects the link. The allowed range is 1 to 10 minutes. • EXAL External Alarm: activate/deactivate the radio external alarm when a call is received. • ALRT Alert tone: enable/disable the generation of an alert tone whenever a link is established.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide • • MultiNet: enable/disable the scanning of multiple ALE nets. When enabled, this feature lets the radio communicate with stations in nets other than the currently selected net. MxCH Maximum Scan Channels: when MultiNet is enabled, the time needed for scanning all the nets may be rather long. This parameter is used to adapt the duration of the calling signal to the number of scanned net, to ensure that communications are not disrupted.
ALE Programming • AMD Yes • ILNK No • BDLK No When configuring ALE options, you do not need to define all parameters – change only those for which the factory-default values are not suitable. Auto Dial Parameters Auto Dial enables you to set shortcuts for calls to frequently called stations, with or without automatically attaching messages when a station is called: • AUTO Used to configure up to 10 autodial codes, numbered AUTO 0 to AUTO 9.
MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide Using the New Station Address Filter To help you add new station addresses to the ALE directory of your radio set in a controlled manner, MICOM-2 has a special ALE address filter. To enable this filter, enable the Auto Address function on the PROG>ALE>OPT>AADR menu (this function can also be enabled by means of the RSS).