ML910™Rugged Notebook User Guide Motorola, Inc. All rights reserved Owner’s Manual R01.
TRADEMARKS MOTOROLA, the Stylized M Logo, and ML910™ RUGGED NOTEBOOK are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their respective owners. © 2008 by Motorola, Inc. All rights reserved NOTE: Information in this user guide is subject to change without notice. COPYRIGHTS ML Application includes the following Publicly Available Software: ListViewEx, http://www.codeproject.com/cs/miscctrl/ListViewCellEditors.asp, Copyright © 2004 mav.northwind.
LICENSE AGREEMENT MOTOROLA, INC. (“MOTOROLA”) IS WILLING TO LICENSE THE SOFTWARE EMBEDDED IN THE ENCLOSED PRODUCT (THE “SOFTWARE”) TO YOU ONLY ON THE CONDITION THAT YOU ACCEPT ALL OF THE TERMS CONTAINED IN THIS LICENSE AGREEMENT (“AGREEMENT”). PLEASE READ THE TERMS CAREFULLY. YOUR USE OF THE PRODUCT WITH THE EMBEDDED SOFTWARE WILL INDICATE YOUR ASSENT TO THEM.
Section 4 CONFIDENTIALITY You acknowledge that all Software contains valuable proprietary information and trade secrets and that unauthorized or improper use of Software will result in irreparable harm to Motorola for which monetary damages would be inadequate and for which Motorola will be entitled to immediate injunctive relief.
EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Section 10 LIMITATION OF LIABILITY OF MOTOROLA’S TOTAL LIABILITY UNDER THIS AGREEMENT FOR DAMAGES SHALL NOT EXCEED THE TOTAL AMOUNT PAID BY YOU FOR THE SOFTWARE UNDER THIS AGREEMENT. IN NO EVENT WILL MOTOROLA BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES. Section 11 U.S. GOVERNMENT If You are a unit or agent of the U.S.
SHOULD RETURN IT TO THE PLACE FROM WHICH IT WAS ACQUIRED, AND YOUR MONEY WILL BE REFUNDED. COMPUTER SOFTWARE COPYRIGHTS The Motorola products described in this user guide may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including the exclusive right to copy or reproduce in any form the copyrighted computer program.
LIMITED WARRANTY MOTOROLA COMMUNICATION PRODUCTS If the affected product is being purchased pursuant to a written Communications System Agreement signed by Motorola, the warranty contained in that written agreement will apply. Otherwise, the following warranty applies. I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG: Motorola Inc.
THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. MOTOROLA DISCLAIMS ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
M) Non-Motorola manufactured equipment unless bearing a Motorola Part Number in the form of an alphanumeric number (e.g., TDE6030B). V. GOVERNING LAW In the case of a Product sold in the United States and Canada, this Warranty is governed by the laws of the State of Illinois and the Province of Ontario respectively. VI.
Regulatory Information SAFE USAGE NOTIFICATION For reasons of personal safety and optimal radio performance, Motorola has designed the ML910™ RUGGED NOTEBOOK with the intended purpose and position of use either in a secured vehicle docking station or on top of an office desk.
Wireless LAN Module Statement FCC CAUTION: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. If the ML910 RUGGED NOTEBOOK computer has the Intel 3945abg module (802.11abg) installed, operation on the 5.15-5.25GHz frequency band is restricted to indoor use only.
FCC RF Exposure Statement This equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of between the radiator and all persons. See page 1-13 of the Users Guide for antenna locations. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
CMM labeling and Disclosure Table The People’s Republic of China require that our products comply with China Management Methods (CMM) environmental regulations. (China Management Methods refers to the Regulation Management Methods for Controlling Pollution by Electronic Information Products.) Two items are used to demonstrate compliance; the Label and the Disclosure Table. The label is placed in a customer visible position on the product.
European Union CE Marking and Compliance Notices Statements of Compliance English This product follows the provisions of the European Directive 1999/5/EC. Danish Dette produkt er i overensstemmelse med det europæiske direktiv 1999/5/EC. Dutch Dit product is in navolging van de bepalingen van Europees Directief 1999/5/EC. Finnish Tämä tuote noudattaa EU-direktiivin 1999/5/EC määräyksiä. French Ce produit est conforme aux exigences de la Directive Européenne 1999/5/EC.
Local Restrictions of 802.11a/b/g Radio Usage CAUTION: Due to the fact that the frequencies used by 802.11a/b/g wireless LAN devices may not yet be harmonized in all countries, 802.11a/b/g products are designed for use only in specific countries or regions, and is not allowed to be operated in countries or regions other than those of designated use.
France Departments in Which the Wireless LAN Module Can Be Used (Indoors Only) The wireless LAN module can currently be used indoors only in the following 38 departments of mainland France.
Product Safety and RF Exposure Information CAUTION: BEFORE USING ML910 RUGGED NOTEBOOK, READ THIS SECTION WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS.
Aircraft When instructed to do so, turn off your ML910 RUGGED NOTEBOOK and/or integrated radios when on board an aircraft. Any use of a ML910 RUGGED NOTEBOOK or radio must be in accordance with applicable regulations per airline crew instructions. Medical Devices Pacemakers Keep the antennas of ML910 RUGGED NOTEBOOK at least 8 inches (20cm) away from any person’s body.
Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death. The areas with potentially explosive atmospheres referred to above include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles, such as grain, dust or metal powders. Areas with potentially explosive atmospheres are often but not always posted.
About the Battery Caution Texts Concerning Lithium Batteries DANISH ADVARSEL! Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren. NORWEGIAN ADVARSEL: Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruksjoner.
dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal. About the Modem CAUTION: 1. Never install telephone wiring during a lightning storm. 2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 4.
Table of Contents Preface...................................................................................................................xxv Chapter 1 Getting Started....................................................................................1-1 Getting the Computer Running...................................................................... 1-2 Unpacking ................................................................................................ 1-2 Installing the Battery Pack..............
Removing the Optical Disk Drive/2nd HDD/2nd Battery .............................2-12 Inserting and Removing a Disk ...............................................................2-15 Using the Video Features ............................................................................2-16 Configuring the Display Modes ...............................................................2-17 Using the Audio Features ............................................................................
ML900 High-Tier Vehicle Docking Station ................................................ 4-9 ML900 Mid-Tier Vehicle Docking Station.................................................. 4-9 RF Pass-Though Combinations ............................................................. 4-10 Enabling RF Pass-Through Option in MLAA & MLUA ............................ 4-11 Chapter 5 BIOS Setup Utility and ML Applications...........................................5-1 When and How to Use the BIOS Setup Utility............
Hard Disk Drive Problems.........................................................................8-9 Keyboard, Mouse, and Touchpad Problems.............................................8-9 LAN Problems.........................................................................................8-10 WLAN Problems .....................................................................................8-10 Modem Problems....................................................................................
Preface This user guide contains information that will help you operate the computer. It is divided into 10 chapters and 4 appendices. Chapter 1, Getting Started, takes you through the process of setting up the computer and identifying its external components. Chapter 2, Operating Your Computer, tells you how to use the computer’s components and features. Chapter 3, Managing Power, provides information on power.
This page intentionally left blank xxvi
CHAPTER 1 Getting Started Congratulations on your purchase of the ML910 RUGGED NOTEBOOK. This high performance notebook computer is especially designed for the practical applications of warehouses, automobiles, vehicles, public security, repairing, assisting the handicapped, and other demanding situations where conventional notebook computers just cannot measure up. This chapter first tells you step by step how to get the computer up and running.
Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation. Unpacking After unpacking the shipping carton, you should find these standard items: l Notebook computer l Accessories: − AC adapter (100~240 VAC, 50/60 Hz) − AC power cord (US) − Battery − DVD including Drivers and User Guide − Windows XP or Windows Vista Business edition Operating System DVD – PCMCIA to Express 34 Card Converter – Nero OEM Suite DVD Inspect all the items.
3. Insert the battery pack into the compartment. 4. Replace the compartment cover and secure the four screws. Initializing the Battery Pack You need to initialize the new battery pack before using it for the first time. New battery packs are warehoused and shipped to customers only partially charged to ensure maximum life when they are placed into service. The battery charging indicator above the keyboard may blink red to indicate a low battery condition.
Connecting to AC Power The computer operates on either external AC power or internal battery power. We recommend that you use AC power when you start up the com puter for the first time. CAUTION: Use only the AC adapter included with your computer. Use of any other AC adapters may damage the computer. NOTE: Power Supply Cord: For US territory: Detachable, minimum 1.8m long. Listed, rated minimum 125V, 2.5A, having a 3/18 AWG, flexible cord.
NOTE: When the AC adapter is connected, it also charges the battery pack. For information on using battery power, see Chapter 3. Opening the Cover 1. Press the top cover latch 2. Lift up the cover. You can tilt the cover forward or backward for optimal viewing clarity. Turning On and Off the Computer Turning On 1. Make sure the computer has a charged battery or is connected to the AC power supply. 2. Press the power button.
3. Each time the computer is turned on, it performs a Power-On Self Test (POST), and the operating system (such as Windows) should load. Turning Off To turn off the computer safely, use the “Shut Down” command of your operating system. NOTE: 1. Pressing the power button for 4 seconds or longer will shut the computer off. If the power button is held for 10 seconds or more once the computer is turned off, this will cause the internal controller to reset. 2.
Taking a Look at the Computer This section identifies the external components of the computer and briefly describes the function of each component. NOTE: Depending on the model you purchased, the appearance of your computer may not exactly be the same as those shown in this user guide. Top of the Computer 1 Ref ΠGetting Started Component Description Internal Modem Behind the M logo is a compartment which provides the various connections for installing Compartment internal modems.
Right-Side Components 1-8 Ref Component Description Œ Security Lock Slot • USB Port Ž Configurable Media Bay Connects an optional security lock to anchor the computer to a desk or other large object. Supports USB 2.0 (i.e. USB High Speed Devices) and Legacy USB Full and Low Speed Devices (i.e. USB 1.1 and USB 1.0); and up to 1A load for each USB Port. Accepts an Optical Disk Drive (ODD) for installing or loading software, accessing data, and playing music/video.
Left-Side Components Ref Component Œ • VGA Port Ž • Serial Port Description See Also Connects an external monitor. P. 4-2 Connects a RS-232 device. P. 4-4 Video Capture This is a video input port that can connect to a Port video capture device. (i.e. analog video camera) Microphone Connector Connects an external microphone. P. 2-18 P. 2-18 P. A-2 • Audio Output Connector Connects a set of headphones, external speakers with amplifier, or an audio recording device.
Rear Components Ref Component Œ RJ-11 Port Connects the telephone line. • RJ-45 Port Connects the LAN cable. Included a link indicator P. 2-19 and an active indicator. Ž GPS RF pass through Port Serves as the interface between the system and external GPS antenna, in conjunction with a P. 2-25 Vehicle Docking station. • Description See Also P. 2-20 WWAN Module Serves as the interface between the system and RF pass antenna of the optional WWAN module, in P.
Front Components Ref Component Œ Stereo Speaker Set • Handle Ž Top Cover Latch • GPS Antenna (optional) Getting Started Description Output stereo audio from the computer. See Also P. 2–18 Allows you to carry your computer with an easy grip. Locks the top cover. P. 1–5 Serves as an antenna for the Global Positioning System (GPS). It is built into the top cover. P.
Bottom-Side Components Ref Description See Also Allows you to remove the Optical Disk Drive, Second Battery or Second Hard Drive. P. 2-15 Allows you to lock the Optical Disk Drive, Second Battery or Second Hard Drive in place. P. 2-13 Contains the hard disk drive of your computer. P. 2-11 • Configurable Media Bay Eject Latch Configurable Media Bay Lock / Unlock Switch Hard Disk Drive Compartment Ventilation Openings • CPU Cooling Fan Contains cooling fan to protect it from overheating.
Antenna Location (Integrated Radio Modems) 43 1 5 6 2 7 4 8 Ref Component Œ GPS Antenna Optional GPS Receiver • External PCMCIA Antenna Mount Location WMC6300 & WMC7300 Ž WWAN Antenna 1 Primary – TX and RX -- MC8775 and MC5725 • WLAN Antenna 1 Primary TX and RX • WWAN Antenna 2 Secondary – RX only -- MC5725 ‘ WLAN Antenna 2 Secondary – RX only ’ “ Getting Started Bluetooth Description See Also Antenna External PCMCIA WDE1000 Antenna Location 1-13
Top-Open Components Ref Œ Component Description LCD Screen with touch panel Displays the output of the computer. Device Indicators See Also P.2-10 Show the current status of the computer’s devices. Power on: Green color. • P. 3-2 & 3 Standby mode: Amber color. Hard disk drive in-use: Amber color (Blinking). P. 2-11 Hard disk heater is on: Red color (Blinking).
Ref Component Description See Also Battery charging indicator. Battery full: Glows green. P.3-2 Battery charging: Glows amber. • Battery low: Red (Blinking). AC indicator. Glows green when the computer is connected to AC power. Ž Power Button • Keyboard • Fingerprint Scanner Device Indicators P. 1-4 P. 3-2 Turns your computer ON or OFF. P. 1-5 Serves as the data input device of the computer. P. 2-3 Contains the fingerprint scanner. P. B-1 Show the current status of the computer’s devices.
Where to Go from Here As your computer is ready for operation, you may want to do any of the following now: For this purpose… 1-16 Do this… To know more about the computer… Go on to the next chapter. To install the operating system if your dealer has not already done so… See the operating system manual. To know more about the operating system… Read the operating system manual. To install the drivers if your dealer has not already done so… See Chapter 6.
CHAPTER 2 Operating Your Computer This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn your computer’s basic operations . If you are already a computer user but are new to notebook computers, you may choose to read only the parts containing information unique to your computer.
Starting and Shutting Down the Computer There are a number of ways to start up and shut down the computer. Starting the Computer You always start the computer using the power button. A computer starts up with an operating system (OS) existing on the storage device such as the hard disk; or from a CD if you have the respective modules installed. The computer will automatically load the OS after you turn it on. This process is called booting.
NOTE: 1. Placing your computer in standby/sleep mode allows you to return to the tasks you were doing the next time you start up the computer. (See “Power Management” in Chapter 3 for more information.) 2. Pressing the power button for 4 seconds or longer shuts the computer off. Pressing and holding down the power button for 10 seconds or more once the computer is turned off causes the internal controller to reset.
Cursor-Control Keys NOTE: 1. The word “cursor” refers to the indicator on the screen that lets you know exactly where on your screen anything you type will appear. 2. It can take the form of a vertical or horizontal line, a block, or one of many other shapes. Numeric Keypad A 15-key numeric keypad is embedded on the typewriter keys as shown next: Numeric keys facilitate the entering of numbers and calculations.
Euro Symbol For the Euro dollar sign : On an UK keyboard, hold down the Alt Gr key and press 4 (which has a Euro sign on it). Windows Keys The keyboard has two keys that perform Windows-specific functions: Windows Logo key and Application key. The Windows Logo key opens the Start menu and performs software-specific functions when used in combination with other keys. The Application key has the same effect as a right mouse click. (See your Windows manual for more information.
Key Description Enables/Disables the keyboard backlight function. Enables/Disables the Touchpad. Decreases the sound volume. Increases the sound volume. 1. Fn+F5: Decreases the LCD brightness. 2. Fn+F6: Increases the LCD brightness. 3. There are 64 levels of LCD brightness.
Key Description Fn+F7 hotkey turns on/off all wireless devices. i.e., WLAN, WWAN, GPS and Bluetooth. Switches the LCD off and on. Switches the display output when an external device is connected. LCD LCD & CRT CRT Serves as the sleep button that you can define with Windows’Power Management. (See “Power Management” in Chapter 3.) Switches the LCD backlight on and off. Switches the Optional GPS Receiver on and off.
Using the Touchpad CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may damage the touchpad surface as well as the RUBBER part of the touchpad. NOTE: 1. By default, the touchpad is enabled. Use the Fn+F2 hot key to enable/disable this function. The touchpad indicator found on the keyboard panel glows red when it is disabled. 2. For optimal performance of the touchpad, keep your fingers and the pads clean and dry. When tapping on the pad, tap lightly. Do not use excessive force.
Term Action Press and hold the left button. Then, move the object by dragging your finger until you reach the new location (drag). Finally, release the left button (drop) when you have finished dragging your selection to the destination. The item will drop into the new location. Drag and drop –or– Gently tap twice on the pad and on the second tap, keep your finger in contact with the pad. Then, move your finger across the pad to drag the selected object to the desired location.
Using the Touchscreen CAUTION: Do not use a sharp object such as a ballpoint pen or pencil on the touchscreen. Doing so may damage the touchscreen surface. NOTE: 1. The touchscreen is pressure sensitive. The presence of any foreign object on the touchscreen may cause the cursor to move erratically. 2. Use an optical cleaning kit such as a brush to remove any foreign objects.
Using the Hard Disk Drive Your computer normally comes with a 2.5-inch Serial-ATA hard disk drive. A hard disk drive is a storage device where your operating system and application programs are stored. This type of drive embodies the latest in fast, reliable mass storage by integrating all the control circuitry necessary for operation directly onto the drive itself. This allows the drive manufacturer to optimize the performance of the drive.
Using the Optical Disk Drive Your computer, depending on your model, comes optionally with an optical disk drive located on the right side of the computer in the Configurable Media Bay. Depending on the model of your computer, the drive may be one of the following: l DVD drive – reads DVD (Digital Versatile Disk) disks in addition to CDs, audio CDs, CD-R, and CD-RW disks. l CD-RW/DVD Combo drive – works both as a DVD drive and CD-RW drive.
2. Slide the multipurpose bay lock/unlock switch to the lock position to secure the optical disk drive/2nd HDD/2nd Battery in place. 3. Tighten the positioning screws to lock the optical disk drive/2 nd HDD/2nd Battery in place. CAUTION: Customers utilizing the secondary battery as the only power source to operate their ML910 RUGGED NOTEBOOK will not receive a battery discharge cutoff warning during use in extreme temperatures (above 50°C and below -10°C).
Removing the Optical Disk Drive/2nd HDD/2nd Battery NOTE: Due to the depth of the Configurable Media Bay, the user may find it helpful to first open the Optical Disk Drive tray in order to easily grasp and remove the Optical Disk Drive. Before shutting down the notebook , use the eject button on the face plate of the drive. Open the tray and then shut down the notebook . Continue with the removal process.
3. Push to release the lock/unlock switch. 4. Push the Eject icon switch to remove the optical disk drive/2nd HDD/2nd Battery . Warning: 1. Without the two positioning screws locked on the base, the unit will no longer be waterproof and will be more susceptible to damage if dropped. 2. The optical disk drive (or any other secondary kit i.e. 2nd HDD/2 nd Battery) needs to be replaced back in the unit for positioning screws to lock on.
NOTE: In the unlikely event that you are unable to release the optical disk drive tray by pressing the eject button, you can manually release the optical media. (See “Optical Disk Drive Problems” in Chapter 8.) Using the Video Features The video subsystem of your computer features: 13.3-inch Display: l 13.3-inch TFT (Thin-Film Transistor) color LCD display with 1280× 800 WXGA (Wide Extended Graphics Array) resolution. l 128 MB discrete video memory.
Configuring the Display Modes Your computer has been set to a default resolution and number of colors before shipment. You can view and change display settings through your operating system. See your operating system documentation or online help for specific information. For displaying in higher resolutions, you can connect an external monitor that supports higher resolutions. (See “Connecting an External Monitor” in Chapter 4 for more information.
Using the Audio Features NOTE: 1. To take advantage of the enhanced audio capabilities, the audio driver supplied with your computer must be installed (see Chapter 6 for details). 2. If you experience interference while recording, try lowering the microphone recording volume.
Using the Communication Features Using the LAN The internal 10/100/1000 Base-T Ethernet LAN (Local Area Network) module allows you to connect your computer to a network. It supports data transfer rate up to 1000 Mbps. When the ML910 RUGGED NOTEBOOK is used in a Vehicle Docking Station or Office Port Replicator the data transfer rate will be limited to 10/100 Mbps.
Using the Wire Line Modem The internal 56K fax/data modem allows you to use the telephone line to communicate with others by fax, email, or connect to an online service or web browser. Connect one end of the RJ-11 telephone cable to the modem port and the other end to the phone line.
Using the Wireless LAN Your computer may have an internal PCIe (PCI Express) Mini Card network adapter (WLAN) pre-installed by the computer manufacturer. This card allows you to access corporate networks or the Internet in a wireless environment. Feature Module 3945ABG for ML910 RUGGED NOTEBOOK Band Indicates the wireless band of the current connection. Rates at which the wireless adapter can send and receive data. Displays the speed in Mbps or the frequency being used. • 802.
Connecting to a Wireless Network For Windows XP 1. Double-click the network connectivity icon located on the Windows system tray. The following window appears on the screen: NOTE: If the Wireless Network connection is disabled, press Fn+F7 to enable it. 2. Select a wireless network to connect to, and then click Connect. 3. You may be asked to enter a key or pass phrase if a network security setting is enabled. Refer to your Windows online help for more information on setting a wireless network connection.
For Windows Vista 1. Double-click the Wireless Software icon The following window appears on screen: located on the Windows system tray. NOTE: If the Wireless Network connection is disabled, press Fn+F7 to enable it. 2. Select a wireless network to connect to, and then click Connect. 3. You may be asked to enter a key or pass phrase if a network security setting is enabled. Refer to your Windows online help for more information on setting a wireless network connection.
Using the PRM240 Wireless Modem (Optional) Your ML910 RUGGED NOTEBOOK may be equipped with an embedded 800 MHz PRM 240 radio modem to provide data connectivity via a Motorola Private DataTAC communications network. This 2 Watt modem is generally compatible only with Private DataTAC systems designed to operate with portable and low power mobile devices, not those systems requiring higher power, external modems such as Motorola's VRM 850.
Using GPS (Optional) Navigation and positioning are crucial to many activities and yet the process has always been quite cumbersome. With GPS technology, you can now figure out where you are and where you are going. Global Positioning System (GPS) is a worldwide radio-navigation system formed from a constellation of 24 satellites and their ground stations. GPS uses these "man-made stars" as reference points to calculate positions accurate to a matter of meters.
Using the MESH Modem (Optional) Motorola's MESH networking technology enables users to wirelessly access critical broadband applications seamlessly–anytime and anywhere. Whether utilizing pre-deployed infrastructure or an instant, ad hoc broadband network formed with other users, Motorola's MESH networking technology delivers real-time data to detect, prevent and respond.
Since devices using Bluetooth technology communicate using radio waves, your computer and the other devices do not need to be in direct line-of-sight. Your computer and the other devices only need to be within a maximum of 10 meters of each other, although the connection can be subject to interference from obstructions such as walls or from other electronic devices. Embedded EVDO REV. A or HSDPA Modem (Optional) Your ML910 RUGGED NOTEBOOK may be equipped with an embedded EVDO REV.
CHAPTER 3 Managing Power Your computer operates either on external AC power or on internal battery power. This chapter tells you how to manage power effectively. In order to ensure optimal battery performance, it is important to use the battery properly.
AC Adapter CAUTION: 1. The AC adapter is designed for use with your computer only. Connecting the AC adapter to another device can damage the adapter. 2. The AC power cord supplied with your computer is for use in the country where you purchased your computer. If you plan to go overseas with the computer, consult your dealer for the appropriate power cord. 3. When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer.
CAUTION: 1. Batteries in ML910 RUGGED NOTEBOOK are allowed to discharge (i.e., operate normally) when the battery temperature is from –20°C (– 4°F) to 60°C (140°F) and allowed to be charged when its temperature is ranging from 0°C (32°F) to 45 °C (113 °F). 2. These batteries are not allowed to operate outside of this range.
Checking the Battery Level NOTE: The battery level indication is an estimation of remaining run time. The actual operating time can be different from the estimated time, depending on how you are using the com puter. You can check the approximate battery level using the battery meter function of the operating system. To read the battery level in Windows, click the icon on the taskbar. (Click the icon if the computer is using AC power.) Replacing the Battery Pack CAUTION: 1. 2. 3. 4.
Battery Low Signals and Actions Battery Low occurs when the battery has approximately 10% (Windows default setting) of its charge remaining. The computer gives warning beeps or messages and the Battery Power Indicator ( ) blinks red to alert you to take actions. NOTE: 1. You can set up your threshold and signals of Battery Low under Windows. 2.
Power Management Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for saving energy. With an ACPI-compliant operating system such as Windows XP and Windows Vista, power supply to different computer components is controlled on an as -needed basis. This allows maximum power conservation and performance at the same time.
ATI PowerPlay TM Management PowerPlay manages the power requirements of your graphics settings for higher performance or longer battery life. Use PowerPlay TM to balance performance and power consumption. When you bought the notebook from Motorola or Motorola’s dealers, PowerPlay is the fixed default driver of the graphics card which can be adjusted under the “Enable PowerPlay procedure. Access to PowerPlay 1. Start notebook and click on the “ATI Catalyst Control Center” symbol.
2. You will see the following screen once you’ve accessed the “ATI Catalyst Control Center” program. 3. Click the “Next” key to proceed to the next step for system access. NOTE: The following will only happen the first time you access the Catalyst Control Center.
Functions of PowerPlay Enabling PowerPlay You can adjust the AC mode and battery mode to reduce the power consumption under the Enable Power Play Function. 1. From the Graphics Settings tree, click PowerPlay 2. Click Enable PowerPlay 3. You will see the following screen: Please check the function of “Enable POWERPLAY” when you access the PowerPlay program.
Select Your Preferred Settings Depending on Power Source The default power settings can be changed to meet your performance to power requirements. 1. From the Graphics Setting tree, click PowerPlay. 2. Click and drag the slider next to the relevant power source to the desired setting. Set Low Battery Level PowerPlay can automatically change to low power consumption settings. NOTE: This option is not available on a notebook running Windows ® Vista. 1. From the Graphics Settings tree, click PowerPlay. 2.
Power-Saving Tips In addition to your computer’s automatic power management, you can do your part to maximize the battery’s operating time by following these suggestions. 1. Do not disable Power Management. 2. Decrease the LCD brightness to the lowest comfortable level. 3. Disable the serial port if no device is connected to this port. (See “Advanced Settings” in Chapter 5.) 4.
CHAPTER 4 Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter.
Connecting an External Monitor If you want the benefits of a larger display screen with higher resolution, you can connect an external monitor that supports VGA interface to your computer. Follow this procedure to connect an external monitor: 1. Make sure that the computer is not turned on. 2. Plug the monitor’s signal connector to the computer’s VGA port. 3. Plug one end of the monitor’s power cord into the power socket on the monitor and the other end to an electrical outlet. 4.
Connecting a USB Device Your computer has three USB ports that support transfer rates of up to 12 Mbps for USB 1.1 devices and 480 Mbps for USB 2.0 devices, such as digital camera, scanner, printer, modem, and mouse. USB is specified to be an industry standard extension to the PC architecture. It supports “Plug-and-Play” technology so you can install and remove USB devices without turning off the computer.
Connecting a Serial Device Your computer has a serial port for connecting a serial device such as an external modem. Follow this procedure to connect a serial device: 1. Plug the device cable to the serial port on the left side of the computer. 2. Turn on the computer. NOTE: Portable modems that derive power through the serial port cannot be used with the computer. Instead, use a modem that is powered by its own internal battery or external AC power.
Connecting a Video Capture Device Your computer has a video capture port for connecting a video source such as high-quality CCD, as well as consumer electronic equipment such as DVCAM and VCR. To connect a video capture device, simply plug the device cable into the video capture (CONEXANT CX23885-12ZP) port of the computer.
System Memory Upgrade You can upgrade your computer by changing system memory to a maximum of 2 GB on the two 200-pin DDR2 SO-DIMM slots. However, to avoid damage during the installation procedure, please ask your dealer for help.
RF Pass-Through RF Pass-Through is a feature that enables the ML910 to receive and transmit radio signals through external antennas for better coverage or range, as compared to using its internal antennas. RF Pass-Through operation depends on having the required RF Pass-Through option and certain wireless options installed in the ML910, as well as a vehicle docking station that supports RF connectivity to the ML910.
RF Pass-Through Retrofit Kit The RF Pass-Through Retrofit Kit allows the user to use the ML910 RF Pass-Through on a ML900 TM Vehicle Docking Station (applicable for both High-Tier and Mid-Tier Vehicle Docking Station). The RF Pass-Through Retrofit Kit is also backward compatible with the ML910 Mid-Tier Vehicle Docking Station so that the RF Pass -Through option can be added to a ML910 Mid-Tier Vehicle Docking Station.
ML900 High-Tier Vehicle Docking Station If the ML910 Rugged Laptop is docked in a ML900 High-Tier Vehicle Docking Station. The ML910 Rugged Laptop internal antenna will remain enabled, and the external antenna will not be used. The RF Pass-Through of the ML910 Rugged Laptop is not compatible with ML900 High-Tier Vehicle Docking Station. The user must install the RF Pass-Through Retrofit Kit to utilize the external antenna.
RF Pass-Through Combinations Table below shows the combination of the different Vehicle Docking Station with ML910 Rugged Laptop.
Enabling RF Pass-Through Option in MLAA & MLUA 1) Launch the ML Administrator Application. 2) Go to the RF Pass-Through Options available in MLAA. 3) Change the RF Pass-Through User Control from [Disable] to [Enable]. 4) Select [Write to EC] to change the setting, a message will be shown after the setting is updated to System EC.
5) Launch the ML User Application. 6) Select the RF Pass-Through option available in the MLUA. 7) Before the RF Pass-Through User Control in MLAA changed to [Enable], the RF Pass-Through Control will be grey-out. 8) After the RF Pass-Through User Control in MLAA had being [Enable], the default setting will be [Automatic Selection]. 9) User can select [Manual Selection] to either Enable or Disable the RF Pass-Through. [Apply] need to be press by User in order to make the selection valid.
11) Note that RF Pass-Through Option will not be applicable if certain conditions have been met. The conditions are shown as below: a. The ML910 do not have RF Pass-Through installed. RF Pass-Through here is refer to RF Antenna Switching Board. b. The ML910 are being docked to either ML900 or ML910 Office Port Replicator. 12) Internal antenna will function if User selects the [RF Pass-Through Off] in the RF Pass-Through Mode.
CHAPTER 5 BIOS Setup Utility and ML Applications BIOS Setup Utility is a program for configuring the BIOS (Basic Input/Output System) settings of the computer. BIOS is a layer of software called firmware that translates instructions from other layers of software into instructions that the computer hardware can understand. The BIOS settings are needed by your computer to identify the types of installed devices and establish special features.
When and How to Use the BIOS Setup Utility When to Use You need to run the BIOS Setup Utility when: l You see an error message on the screen requesting you to run Setup. l You want to restore the factory default settings. l You want to modify some specific settings of the hardware. l You want to modify some specific settings to optimize system performance. Starting BIOS Setup NOTE: 1. The Setup screens shown in this chapter are for your reference only.
Key Function F1 General Help F2 General Help F9 Load optimal defaults F10 Save and Exit ← → Select Screen ↑↓ Select Item ┼─ Change Field/Option Enter 1) Brings up the sub-menu when available. 2) Opens or closes the options window when an item is selected. Tab Jumps from one item to another. Esc 1) Exits the BIOS Setup Utility. 2) Returns to the previous menu if in a sub-menu. 3) Closes the options window if one is open.
Advanced Menu CPU Configuration Setup function of “Intel SpeedStep Technology“: Under the “Advanced”,tab use éê keys to move cursor over the string of “Intel SpeedStep Technology” and you will find the options of “Maximum”, “Minimum”, “Automatic” & “Disabled” displayed on the right top corner of screen. l Maximum: CPU speed is set to maximum. l Minimum: CPU speed is set to minimum. l Automatic: CPU speed is controlled by OS. l Disabled: Use default CPU speed.
Drive Configuration While entering setup, BIOS auto detects the presence of devices. The following screen displays the status of auto detection of devices. Device Information These information is detected by system automatically. It is suggested not to change it.
Peripherals Configuration Enables or disables the feature of “Peripherals Configuration”: Under the “Advanced” tab, use the éê keys to move cursor over the string of peripherals and enable or disable peripherals configuration as needed. System Recovery System Recovery Hotkey: Enable or Disable System Recovery Hotkey by (Ctrl+F9). System Recovery Password: The BIOS supports the recovery of the HDD with a Ctrl+F9 during POST by using one to six character password.
Set and Change Password: Select Change Password from the System recovery password Setup menu and press . “Enter New Password” appears. Type the password and press . The screen does not display the characters entered. Retype the password as prompted and press . If the password confirmation is incorrect, an error message appears. The password is stored in NVRAM upon completion.
Boot Settings Boot Se ttings: Under the “Boot” tab, use the éê keys to move cursor over the string of “Boot Settings Configuration”, “Boot Device Priority”, “Hard Disk Drives” & “Removable Drives” for configuring the following features. l Boot Setting Configuration: Configure POST behavior. l Boot Device Drives: Set the Boot Device Priority Sequence. l Hard Disk Drives/Removable Drives/CD & DVD Drives: Set the Boot Device Priority Sequence from available Drives.
Boot Settings Configuration Under the “Boot” tab, use the éê keys to move cursor over the string of “Quick Boot”, “Quiet Boot” & “NumLock on Boot” to enable or disable the feature. l Quick Boot: Enable or Disable Quick Boot. Enabling this option will allows BIOS to skip certain tests while booting, this will decrease the time needed to boot the system. l Quiet Boot: Enabling this option will show logo screen instead of POST messages. l NumLock on Boot: set status & NumLock when system boots.
Boot Device Priority Set the boot sequence from the available devices. A device enclosed in parenthesis has been disabled in the corresponding type menu.
Security Settings BIOS Password Setup Provides for both a Supervisor and a User password. If you use both passwords, the Supervisor password m ust be set first. The system can be configured so that all users must enter a password every time the system boots or when Setup is executed, using either the Supervisor password or User password. The Supervisor and User passwords activate two different levels of password security. If you select password support, you are prompted for a one to six character password.
Change Supervisor Password: Select Change Supervisor Password from the Security Setup menu and press . “Enter New Password” appears. Type the password and press . The screen does not display the characters entered. Retype the password as prompted and press . If the password confirmation is incorrect, an error message appears. The password is stored in NVRAM upon completion. Change User Password: Select Change User Password from the Security Setup menu and press .
Exit Options CAUTION: If there is a conflict with the ML910 RUGGED NOTEBOOK Com Ports resource, there is a work -around to fix the conflict when you use I/O resources "2F8h", "3F8h", "2E8h" or "3E8h" assigned to PCMCIA card. Please enter "BIOS Setup Utility" menu and perform the following setup procedure: 1. Click “Advanced “. 2. Select “Peripherals Configuration”. 3. To disable "Serial Port 1". ("Serial Port 1" is located on the left side of the notebook.
ML User Application (MLUA) As previously described , the MLUA is designed for users to configure the parameters of various functions in the notebook. By using these configuration parameters, you can change the default configuration that automatically loads when you turn on the computer. ML User Application is automatically launched every time you boot your notebook into Windows Operating System. This can be indicated by the ML User Application icon on the task bar.
• Temperature tab displays the following temperature readings from different sensors located on the system: o o o o o o Processor Temperature LCD Display Temperature System Temperature Hard Disk Drive Temperature Primary Battery Temperature Secondary Battery Temperature • Battery tab allows user to select the most frequently used battery charger profile which defines the battery calibration cycle.
ML Administrator Application (MLAA) This application is designed for administrator to configure the parameters of various functions in the notebook. By using these configuration parameters, you can change the default configuration that automatically loads when you turn on the computer. Every time you start the ML Administrator Application, the current configuration parameters saved in EC is loaded and displayed in the ML Administrator Application window.
This page intentionally left blank BIOS Setup Utility & MLUA 5-17
CHAPTER 6 Installing Software Drivers To take full advantage of the unique features of your computer, some operating systems require custom ized software, known as drivers, to be installed. If you purchased the computer with Windows pre-installed, your dealer may have already installed the drivers. If not, you need to install the drivers using the driver DVD supplied with your computer. This chapter describes how to install the drivers.
How to Use the Driver DVD NOTE: 1. The drivers may have been updated after this user guide was published. For latest driver updates, please contact your dealer. 2. The available items may differ according to your computer model and operation system. 3. In order to access the User Guide on this DVD you will need to have a copy of ADOBE™ Acrobat Reader on the computer or access to the Internet by the computer to use the ADOBE hot link icon to download the reader.
Main Menu The Main Menu Screen: To install drivers and applications for your computer, make your selection correctly. Vista and XP Device Drivers Provides access to the available drivers’selections that apply to the operating system in your computer. Be sure to validate which OS your computer is using before installing any drivers or applications. Browse DVD Allows you to browse the contents of this DVD. Requires the ADOBE Reader.
Installing Device Drivers Click on either “Vista Drivers” or “XP Drivers” in the “Main Menu” based on the operating system that you are using. After selecting either Vista Drivers or XP Drivers the next step is to select Device Drivers or Applications to be installed. The Menu Trees shown in Figure 6-1 provides a list of the possible selections for both operating systems.
Selecting EVDO Clicking on the EVDO button for either OS will allow for the selection of the Wireless Watcher or the MC5725 Driver • Wireless Watcher - Click on the Wireless Watcher button to install the EDVO Sierra Wireless Watcher • MC5725 Driver - Click on the EVDO MC5725 Driver button to install the EVDO driver Registry Clicking on the Registry button for either OS will access a file, GPS_COM.reg. This is neither a driver nor application, but it is a required patch for GPS Operation.
Additional XP Applications In addition to the ML Administrator and User applications common to both Vista and XP, there are 2 other XP Applications that are available to be installed. • MW800 Display Utilities Click on the MW800 Display Utilities button to install the MW800 Display Application Utilities • NET Framework 2.0 Click on the NET Framework 2.0 button to install NET Framework 2.0. This is required to run ML Application.
CHAPTER 7 Caring for the Computer Taking good care of your computer ensures trouble-free operation and also reduces the risk of damage to your computer.
Protecting the Computer To safeguard the integrity of your computer data as well as the computer itself, you can protect the computer in several ways as described in this section. Using the Password The power on password protects your computer against unauthorized use. If the password is set, a prompt requesting for the password appears on the screen whenever the computer is turned on. The password is set via the BIOS program. See “S ecurity Settings” in Chapter 5 for instructions.
Taking Care of the Computer Location Guidelines l Use the computer where the temperature is between -20°C (-4°F) and 50°C (122°F). l Avoid placing the computer in a location subject to high humidity, extreme temperatures, mechanical vibration, direct sunlight, or heavy dust. l Do not cover or block any ventilation openings on the computer. For example, do not place the computer on a bed, sofa, rug, or other similar soft surface.
Battery Pack Guidelines Optimal Use of the ML910 RUGGED NOTEBOOK Battery The battery is a consumable product and its performance will gradually degrade based on usage. To minimize battery degradation and ensure longer life, limit the number of charges and ensure the battery is not exposed to high ambient temperatures. If possible, the battery pack should only be recharged when it is nearly fully discharged.
• If possible, charge the battery while the computer is powered off. When the computer’s power is on, the temperature inside the battery will increase due to the heat generated by the internal electronic components. Charging the battery at higher temperatures will degrade the battery more quickly. It is highly recommended that you charge the battery while the computer is powered off. This allows for faster charging, less degradation, and longer battery life.
If the battery has been stored out of the notebook computer, longer than 60 days, it should be checked for remaining charge condition. If the capacity display is below 20% of remaining charge, the battery should be charged up to 30 to 45% before being placed back in storage. Removal of the Battery Pack • Do not install or remove battery while the computer is on or connected to external power.
When Traveling l Before traveling with your computer, make a backup of your hard disk data into optical disks or other storage devices. As an added precaution, bring along an extra copy of your important data. l Make sure the battery pack is fully charged. l Make sure the computer is turned off. l Do not leave objects that will press onto the display. l Disconnect the AC adapter from the computer and take it with you. Use the AC adapter as the power source and as a battery-charger.
This page intentionally left blank.
CHAPTER 8 Troubleshooting Hardware, software, or a combination of both can cause computer problems. This chapter tells you what actions to take when solving common computer problems.
Preliminary Checklist Here are helpful hints to follow when you encounter any problems before taking further action. l Try to isolate the part of the computer causing the problem. l Make sure you turn on all peripheral devices before turning on the computer. l If an external device has a problem, make sure that the cable connections are correct and secure. l Make sure the configuration information is properly set in the BIOS Setup Utility. l Make sure all the device drivers are correctly installed.
Solving Common Problems For easy reference, the problems are divided into these categories. Problem Type Go to Battery Problems P. 8-4 Bluetooth™ Problems P. 8-6 ODD Drive Problems P. 8-6 Display Problems P. 8-7 Hardware Device Problems P. 8-8 Hard Disk Drive Problems P. 8-9 Keyboard, Mouse and Touchpad Problems P. 8-9 LAN Problems P. 8-10 WLAN Problems P. 8-10 Modem Problems P. 8-11 Power Management Problems P. 8-12 Software Problems P. 8-12 Sound Problems P.
Battery Problems The battery does not charge (Battery Charge indicator does not glow amber). l Make sure the AC adapter is properly connected. l Make sure the battery is within the recommended charging temperature range (0-40oC). Allow time for the battery pack to return to room temperature. l Make sure the battery pack is correctly installed. l Make sure the battery terminals are clean, clear of debris, foreign objects, and corrosion. CAUTION: Do not touch or attempt to clean the terminals.
The battery operating time indicated by the battery meter does not match the actual operating time. l The actual operating time can be different from the estimated time, depending on how you are using the computer. If the actual operating time is much less than the estimated time, initialize the battery. (See “Initializing the Battery Pack” in Chapter 3 for instructions.
Bluetooth Problems Unable to connect to another Bluetooth-enabled device. l Make sure both devices are Bluetooth activated. l Make sure the distance between the two devices is not over 10 meters or that there are no walls or other obstructions between the devices. l Make sure the other device is not in “Hidden” mode. l Make sure both devices are compatible (i.e., support the same profile). Unable to end/terminate a BluetoothTM connection.
Display Problems Nothing appears on the screen. l If the power on indicator is not on, check the electrical outlet, the plugs and power cords. l If the power button does not respond to a light touch, press the button firmly. l If you are using battery power, make sure that it has a remaining charge and that it is installed correctly. l During operation, the screen may automatically turn off as a result of power management. Press any key to see if the screen comes back.
l Switch the display to the monitor by pressing Fn+F9, or change the display through the settings in Display Properties. Simultaneous display/multi-display does not work. l Make sure you turn on the external monitor before turning on the computer. l Press Fn+F9 to toggle through the display options or change the settings in Display Properties in Windows. Hardware Device Problems The computer does not recognize a newly installed device.
Hard Disk Drive Problems The hard disk drive error message appears on the screen. l Insert a bootable hard disk (CD or DVD) and check the integrity of your hard drive. l If the hard disk drive has defects, ask your dealer for help. The hard disk drive operation is slow. l The data files stored on the hard disk drive may be badly fragmented. Use a tool such as Window’s Disk Defragmenter to rearrange the files and improve the performance. The hard disk drive in-use indicator glows without blinking.
LAN Problems Unable to Access the Network. l Make sure the LAN driver is correctly installed. l Make sure the LAN cable is properly connected to the RJ-45 connector and the network hub. l Make sure the network is properly setup and configured. l Make sure the user name or password is correct. WLAN Problems Unable to Access the WLAN Feature. l Make sure the WLAN card is correctly installed. l Make sure the necessary driver(s) is/are correctly installed. l Make sure the WLAN feature is turned on.
l If all else fails, consult your dealer or an experienced radio technician for help. Unable to Connect to Another WLAN device. l Make sure the WLAN feature is turned on. l Make sure the SSID setting is the same for every WLAN device in the network. l Your computer is not recognizing changes. Restart the computer. l Make sure the IP address or subnet mask setting is correct. Unable to Communicate with the Computer in the Network when Infrastructure Mode is Configured.
Power Management Problems The computer does not enter standby/sleep mode automatically. l When your computer is connected to another device, it may not enter standby/sleep mode if the connection is actively in use. l Make sure the standby/sleep time-out is enabled. The computer does not enter standby/sleep mode immediately. l If the computer is busy performing tasks, it will only enter standby/sleep mode after completing the tasks. The computer does not resume from standby/sleep mode.
Sound Problems No sound is audible. l Make sure the volume control is not set too low. l Make sure the audio driver is correctly installed. l Make sure the computer is not on Standby mode. l If using an external speaker, make sure the speaker is properly connected. Distorted sound is produced. l Make sure the volume control is not set too high or too low. In many cases, a high setting can cause the audio electronics to distort the sound. The sound system does not record.
Resetting the Computer You may have to reset (reboot) your computer when an error occurs and the program you are using hangs up. If the system operation appears to hang, wait for a while. It is possible that the system is processing data. Check the hard disk drive in-use indicator. If it blinks irregularly, the program may be accessing data and preventing you from using the keyboard.
The HDD Recovery Process System Recovery Program Your system comes with a System Recovery program that can help you to diagnose and solve problems you found on your system. It consists of the following options: • Run System Restore Utility– This option will activate the System Restore function, which is a component of Windows XP and Vista that you can use to restore your computer to its previous state without losing your personal data files.
2. You will be prompted for the System Recovery password, enter the password then press Enter key to continue. Note: • The default System Recovery password is 123456. • It can be changed in BIOS Setup. • If you fail to enter the correct password in 3 attempts, the system will be halted and you will need to restart the system in order to try again. 3. The system will boot into System Recovery program if you enter the correct password.
4. This is the Welcome screen you will see if you successfully activate the System Recovery program. The standard navigation of the program are outlined as below: • To proceed to the next step, click on the Next button. • To go back to previous screen, click on the Back button. • To go back to the Welcome screen, click on the Cancel button. • To terminate this program and restart to Windows, click on the Exit button. 5. You will be presented with the options of tasks that you may perform with this program.
6. If you select System Restore Utility as the task that you want to perform, you will be presented with this screen. • To proceed with System Restore, click on the Next button. 7. System Restore will be launched automatically after the system restarts.
8. If you select System Recovery as the task that you want to perform, you will be presented with this screen. • To proceed with System Recovery, click on the Next button. 9. Please wait while the System Recovery is in progress. It may take up to 10 minutes to complete.
10. System Recovery is successfully completed. • To restart your system, click on the Exit button. 11. If you selected Disk Diagnostic Utility as the task that you want to perform, you will be presented with this screen. • To proceed with Disk Diagnostic Utility, click on the Next button.
12. Please wait while Disk Diagnostic Utility is checking your hard drive. 13. Disk Diagnostic Utility will show the summary of the disk diagnosis. • To see the detailed result, click on the Click here to see the Disk Diagnostic Result link. • To exit the program and restart to Windows, click on the Exit button.
This page intentionally left blank.
CHAPTER 9 Accessories List Item No. Part No.
** Note: The smartcard reader (HKLN4359A) was designed to meet the ISO7816 operating temperature requirements (0-50C) and does not meet the MIL SPEC-810F temperature requirements. Operating outside of this temperature range may result in abnormal behavior. Item No. Part No.
CHAPTER 10 Acronyms Item Acronym Description 1. ACPI Advanced Configuration and Power Interface: an industry-standard specification (co-developed by Hewlett-Packard, Intel, Microsoft, Phoenix, and Toshiba, for operating-system -directed power management for laptop, desktop, and server computers. A replacement for APM. 2. AP Access Point. 3. BIOS Basic Input/Output System. 4. BSSID Basic Service Set Identifier. 5. DC Direct Current. 6.
Item Acronym 10-2 Description 17. NVRAM Nonvolatile RAM, RAM that ret ains its contents when a unit is turned off. 18. ODD Optical Disk Drive. 19. OS Operating System. 20. PCMCIA Personal Computer Memory Card International Association. An industry trade association that creates standards for notebook computer peripheral devices such as PC cards. 21. PVDT Private DataTAC, a registered trademark of Motorola Inc. 22. RAM Random Access Memory, a type of computer data storage.
This page intentionally left blank.
APPENDIX A Specifications NOTE: Specifications are subject to change without any prior notice. Parts Specifications CPU Intel® Core™ Duo L2400 1.66 GHz Processor. Video Graphics Adapter ATI Mobility Radeon™ X1400 (dedicated 128 MB) MotionComp capability, supports hardware aid for DVD playback. Support s Dual View function. LCD/CRT display. Memory 2 MB L2 Cache ROM BIOS 512 KB Flash EEPROM, system and VGA BIOS, ACPI 2.0, PC2001-compliant.
Parts • Fingerprint Scanner; 500 dpi (Requires customer-provided software application. ) • PCMCIA: 1 x External Type II – Cardbus support. (Accessory PCMCIA to PCI Express 34 converter card included.) • I/O ports: * 1 x Serial * 3 x USB 2.0 * 1 x RJ-11 * 1 x DC input * 1 x Shrouded Hot-docking Port * 1 x RJ-45 10/100/100 Base-TLAN * 2 x External RF Pass-Through Ports (1:GPS, 1:WWAN) I/O Ports Modem LAN Communications Specifications 56 K (V.90/V.
Parts Spe cifications Dimension (W×D×H) 3.2” x 11.1” x 13.2” (336 mm x 283 mm x 78 mm) Operating System Supports Windows XP, SP2, Windows Vista Business SP1 edition Temperature According to IEC 68-2-1,2,14/MIL-STD -810F, Method 501.4, 502.4 Operating: –20ºC to 60ºC (Tested) Humidity According to IEC 68-2-30/MIL-STD-810F, Method 507.4 5% to 95% RH, non -condensing Altitude According to IEC 68-2-30/MIL-STD-810F, Method 500.
This page intentionally left blank A-4 Specifications
APPENDIX B Fingerprint Recognition Your ML910 RUGGED NOTEBOOK features a fingerprint recognition system designed for computer security. It provides a high level of user convenience and gives you a set of powerful tools for securing your com puter and protecting your private data. The system can: • Display fingerprint images derived from the sensor IC . • Enroll new users . • Extract fingerprint templates from raw images, and store them in a local database.
Finger Placement 1. The fingerprint sensor is located at the left side of the palm rest. 2. Slide your finger in the arrow’s direction firmly with steady pressure. NOTE: Be sure that you are making contact with the sensor surface during the scan. The system works best when user follows the recommended direction.
Fingerprint Recognition The ML910 RUGGED NOTEBOOK has a separate embedded Fingerprint Module and a Trusted Platform Module (TPM) included in the unit. This will allow ML910 RUGGED NOTEBOOK to support applications for Trusted Platform Module (TPM) and Fingerprint Recognition. 1. Fingerprint Module can support Fingerprint Recognition applications which can provide for the following features: l Computers l Application of Protection l Secure Windows Logon l Enterprise Class Password Management l File NOTE: 1.
This page intentionally left blank.
APPENDIX APPENDIX C Self Install Internal Wireless Modems Most customers will purchase their embedded EVDO or HSDPA WWAN modems from Motorola and have them pre-installed by the factory. It is possible to add an EVDO REV A. or HSDPA WWAN (Cellular Carrier) modem later by purchasing a WWAN module from Motorola. Normally, Motorola ’s Agencies can provide several kinds of Wireless Internal Modules which are different in number of connectors and the number of WWAN cables that are connected.
Installation of the HSDPA Internal Modem HSDPA Internal kits should have one mini Card port and one WWAN cable such as HKUN4071 and HKUN4073. Please refer to following procedure for installation. Remove the M logo for installation. l Remove one screw from the M logo. l Remove the M logo.
l You will find two antenna (WWAN) cables attached by two pieces of Kapton® tape on the mini card bracket. l Remove Kapton® tape from the cable. l Remove two screws from the mini card bracket.
l Insert the Wireless HSDPA Modem Kit. l Fix two screws on the Wireless HSDPA Modem kit.
l Snap the Black WWAN cable onto the main port on the mini card. l Insert the SIM card. l Installed Internal Wireless HSDPA Modem kit with SIM card.
l Place the M logo cover back on ML910 RUGGED NOTEBOOK unit. l Fix the M logo with a screw.
Installation of the EVDO REV. A Internal Modem EVDO REV. A Internal Kits should have two mini card port connectors and two WWAN Cables such as in Kit No. HKUN4067 and HKUN4075. Please refer to following procedure for installation. l Remove one screw from the M logo. l Remove the M logo.
l You will find two antenna (WWAN) cables attached by two pieces of Kapton® tape on the mini card bracket. l Remove Kapton® tape from the cable. l Remove two screws from the mini card bracket. l Insert the Wireless EVDO REV. A Module Kit.
l Fix two screws on the Wireless EVDO REV. A Module. l Snap the Black WWAN cable onto the Main port of the mini card and the White WWAN cable onto the AUX post of the mini card. l Place the M logo back on ML910 RUGGED NOTEBOOK unit.
l Fix the M logo with a screw.
Installation of the PRM240 Internal Modem l Remove one screw from the M logo. l Remove the M logo. l You will find two WWAN cables attached by two pieces of Kapton® tape on the mini card bracket. l Remove Kapton® tape from cables.
l Each PVDT Modem Installation Kit (PRM w/o Modem) (kit no. HKUN4066), it includes one FFC cable, one MMCX cable and one PRM240 Internal Modem module. l Connect one side of the MMCX cable to the PRM240 module.
l Remove four screws from the mini card bracket. l Remove the mini card bracket from ML910 RUGGED NOTEBOOK unit. l Snap the Black WWAN cable to the MMCX cable prior to installing the module.
l Place the PRM240 module on ML910 RUGGED NOTEBOOK by matching each corner of the PRM240 Internal Modem module with the four screw holes . l Fix four screws back on to lock the PRM240 Internal Modem Module. l Connect the FFC cable to the FFC connector on the main board.
l Place the M logo back on ML910 RUGGED NOTEBOOK unit. l Fix the M logo with a screw.
APPENDIX APPENDIX D RoHS / WEEE RoHS / WEEE D-1
D-2 RoHS / WEEE
RoHS / WEEE D-3
D-4 RoHS / WEEE
RoHS / WEEE D-5
D-6 RoHS / WEEE
