ET1 ENTERPRISE TABLET QUICK START GUIDE
Motorola Solutions reserves the right to make changes to any product to improve reliability, function, or design. Motorola Solutions does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
Features Decode LED Microphone Light Sensor Battery Charge LED Communication LED Front-facing Camera Touch Screen Programmable Buttons Back Button Home Button Menu Button 3
Features Secondary Microphone Rear-facing Camera Flash Camera USB Host Expansion Module, Scanning Module or Scanning/MSR Module Right Scan/Action Button Power Button Left Scan/Action Button Battery Charging LED Battery Release Latch Battery Speaker Speaker Headset Jack 4 I/O Connector HDMI Output Connector
Introduction Install the SIM Card This guide covers the following configurations: The ET1N2 requires an activated SIM card. Obtain the card from a service provider. • ET1N0 (WLAN only) • ET1N2 (WLAN and WAN) • ET1N0 and ET1N2 with scan modules. Getting Started 1. Lift the access door. 2. Insert SIM card into SIM holder with the contacts facing down and the cut edge facing away from the holder. 3. Close the access door.
Install the Battery CAUTION Charge the Battery Ensure that the correct battery is used with the ET1. On the ET1N0 use either the 4620 mAh battery, p/n 82-149690-xx or the 5640 mAh battery, p/n 82-158261-xx. On the ET1N2 use only the 5640 mAh battery, p/n 82-158261-xx. The battery part number is found on the battery label. 1. Remove the battery from the packaging.
WAN Activation In order to use the WAN radio for data communication, the ET1N2 must be activated on the service provider’s network. By default, the ET1N2 is configured for a GSM network. To activate on a CDMA network, manually configuration is required. For WAN data configuration, refer to the ET1 Integrator Guide. a. Press and hold the Power button until the Device options menu appears. b. Touch Reset. After resetting the Activate the ET1 screen appears.
Launch Applications Configure the ET1 To launch an application: To configure ET1 settings, touch . Refer to the ET1 Enterprise Tablet User Guide and Integrator Guide for information on configuring the ET1. 1. Touch . The APPS screen displays. Power Button Use the Power button to place the ET1 in suspend mode, battery swap mode, to reset the ET1 or to power off the ET1. All Apps icon 2. Touch an application icon to launch the application.
Reset Reset the ET1 if applications stop responding. Press and hold the Power button until the dialog box appears then touch Reset. Refer to the ET1 Enterprise Tablet User Guide for setup instruction for locking the screen. If the Multi-user feature is enabled, contact the system administrator for login information. Power Off Change Volume To power off the ET1, press and hold the Power button until the dialog box appears, then touch Power off. When the Power off dialog box appears, touch OK.
Scan a Bar Code Using the Camera Depending upon configuration, bar code scanning can be performed using the Scan Module, Scan/MSR Module or rear-facing camera. Use the rear-facing camera to scan bar codes. Ensure that DataWedge is enabled and the cursor is in a text field. Using the Scanning Module Use the Scanning or Scanning/MSR Module to scan bar codes. Ensure that DataWedge is enabled and the cursor is in a text field. 1. Point the back of the ET1 at the bar code. 2.
Photos and Videos To capture video: Use the rear-facing camera to take photos and capture video. 1. Touch NOTE A microSD card is required to save photos and videos. > and then touch the video icon . 2. Point the ET1 at the subject. 3. On the screen, frame the subject in the window. 4. Touch the on-screen record button 5. Touch the on-screen stop button to begin recording. to end recording. View photos and videos using the Gallery application. To take a photo: 1. Touch > . 2.
Magnetic Stripe Card Reading Connect to a Bluetooth Device Use the Scanning/MSR Module to read magnetic stripe card. To enable Bluetooth: 1. Ensure that DataWedge is enabled and the cursor is in a text field. 2. Align the magnetic stripe on the card toward the display and swipe the card in either direction. 1. Touch > Wireless & networks. 2. Slide the Bluetooth switch to the ON position. The Bluetooth icon appears in the Status bar indicating that Bluetooth is enabled. 3. Touch Bluetooth.
Connect to a WLAN Network Connect to a Mobile Data Network To set up a WLAN network: To connect the ET1N2 to a mobile data network: 1. Touch 1. Touch > Wireless & networks. 2. Slide the Wi-Fi switch to the ON position. Touch Wi-Fi. The ET1 searches for WLANs in the area and lists them. 3. Select the desired network. 4. For open networks, the ET1 automatically connects. For secure networks enter the required password or other credentials then touch Connect.
5. Press thumb against the side of the ET1 and battery. Using the index and middle fingers, move the battery release latch toward thumb and pull the battery out of the battery compartment. 6. Align the tracks on the side of the replacement battery with the rails in the battery compartment. 7. Push the battery in until the battery release latch snaps into place. 8. Press the Power button to turn on the ET1.
Accessories The following accessories are available for the ET1: • Single-slot Docking Cradle • Four-slot Charge Only Docking Cradle • Four-slot Battery Charger • Scanning Module • Scanning/MSR Module • Handstrap • Holster • Protective Rubber Bezel • USB/Charge Cable • Two-way DC Cable • Power supplies.
Motorola Solutions, Inc. 1301 E. Algonquin Rd. Schaumburg, IL 60196-1078, U.S.A. http://www.motorolasolutions.com MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2013 Motorola Solutions, Inc. All Rights Reserved.