PROFESSIONAL DIGITAL TWO-WAY RADIO SYSTEM MOTOTRBO™ DM 3600/DM 3601 DISPLAY MOBILE USER GUIDE
Contents Important Safety Information . . . . . . . . . . . . . . . . . vii Product Safety and RF Exposure Compliance . . vii Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Computer Software Copyrights . . . . . . . . . . . . . . viii Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 How to Use This User Guide . . . . . . . . . . . . . . . . . . 1 What Your Dealer/System Administrator Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . Making a Call with the Channel Rocker . . . . . . . Making a Group Call . . . . . . . . . . . . . . . . . . . . Making a Private Call . . . . . . . . . . . . . . . . . . . Making an All Call . . . . . . . . . . . . . . . . . . . . . . Making a Group or Private Call with the One Touch Access Button . . . . . . . . . . . . . . . . . Stopping a Radio Call . . . . . . . . . . . . . . . . . . . . . . Talkaround . . . . . . . . . . . .
Deleting All Sent Text Messages from Sent Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Receiving a Text Message . . . . . . . . . . . . . . . . . 52 Reading a Text Message . . . . . . . . . . . . . . . . . . . 52 Managing Received Text Messages . . . . . . . . . . 53 Viewing a Text Message from the Inbox . . . . . 53 Viewing a Telemetry Status Text Message from the Inbox . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Replying to a Text Message with Quick Text . .
Contents Turning the Voice Operating Transmission (VOX) Feature On or Off . . . . . . . . . . . . . . . . . . . . . . . . 64 Turning the Public Address System On or Off . . 65 Turning the External Public Address System On or Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Controlling the Display Backlight . . . . . . . . . . . . 65 Turning Horns/Lights On or Off . . . . . . . . . . . . . . 66 Turning the Radio Tones/Alerts On or Off . . . . .
Contents Editing and Sending a Saved Text Message . . 91 Managing Fail-to-Send Text Messages . . . . . . . . 92 Forwarding a Text Message by Manual Dial . . 92 Editing a Text Message . . . . . . . . . . . . . . . . . . 93 Dual Tone Multi Frequency (DTMF) . . . . . . . . . . . . 93 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Radio Disable via Manual Dial . . . . . . . . . . . . . . . 94 Radio Enable via Manual Dial . . . . . . . . . . . . . . . 94 Password Lock Features . .
Notes Notes vi English
Software Version Product Safety and RF Exposure Compliance All the features described in the following sections are supported by the radio's software version R01.08.00 or later. ! Caution Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. See Checking the Firmware Version on page 71 to determine your radio's software version.
Computer Software Copyrights Computer Software Copyrights The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program.
Getting Started How to Use This User Guide Selected features are also available on the single-site trunking mode, Capacity Plus. See Capacity Plus on page 7 for more information. What Your Dealer/System Administrator Can Tell You You can consult your dealer or system administrator about the following: This User Guide covers the basic operation of the MOTOTRBO Mobiles.
To turn off the radio, press and hold the On/Off Button until you see Powering Down on the radio’s display. Powering Up the Radio Press the On/Off Button briefly. You see Motorola and MOTOTRBO (TM) on the radio’s display momentarily, followed by Motorola once more. On/Off Button Adjusting the Volume To increase the volume, turn the Volume Knob clockwise. Volume Knob Getting Started The green LED blinks and the Home screen lights up if the backlight setting is set to turn on automatically.
1 Identifying Radio Controls Radio Controls 4 11 10 9 5 page 3 page 4 page 6 page 6 page 7 page 7 12 1 On/Off Button 7 Front Button P3* 2 Volume Knob 8 Front Button P4* 3 Front Button P1* 9 Menu Navigation Buttons 4 Display 10 Front Button P2* 5 Channel Rocker 11 Accessory Connector 6 Speaker 12 LED Indicators 8 7 6 Identifying Radio Controls Take a moment to review the following: Radio Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Programmable Buttons . .
Programmable Buttons Your dealer can program the programmable buttons as shortcuts to radio functions or up to a maximum of six (6) preset channels/groups depending on the duration of a button press: • Short press – Pressing and releasing rapidly (0.05 seconds). • Long press – Pressing and holding for the programmed Identifying Radio Controls duration (between 1.00 second and 3.75 seconds). 4 • Hold down – Keeping the button pressed.
Radio Disable disabled. – Allows a target radio to be remotely Assignable Settings/Utility Functions Repeater/Talkaround* – Toggles between using a repeater and communicating directly with another radio. Backlight – Controls the backlight intensity. Horns/Lights – Toggles horns and lights feature on or off. Power Level – Toggles transmit power level between high and low. Scan* – Toggles scan on or off. Site Lock On/Off* off. – Toggles the automatic site roam on or Telemetry Control remote radio.
Accessing the Programmed Functions You can access various radio functions through one of the following ways: • A short or long press of the relevant programmable buttons. Identifying Radio Controls OR • Use the Menu Navigation Buttons as follows: 1 To access the menu, press the S button.
You can turn off the Channel Free Indication tone or the PTT Sidetone by disabling all radio tones and alerts (see Turning the Radio Tones/Alerts On or Off on page 66). Switching Between Conventional Analog and Digital Mode Each channel in your radio can be configured as a conventional analog or conventional digital channel. Use the Channel Rocker to switch between an analog or a digital channel. Channel Rocker When switching from digital to analog mode, certain features are unavailable.
Power Level Radio is set at Low power. Identifying Status Indicators Identifying Status Indicators Your radio indicates its operational status through the following: Display Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 8 Call Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9 Sent Item Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10 LED Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unread Message User has unread message(s) in the Inbox. Call Icons Emergency Radio is in Emergency mode. Secure The Privacy feature is enabled. Unsecure The Privacy feature is disabled. Site Roaming* The auto roaming feature is enabled. Talkaround* In the absence of a repeater, radio is currently configured for direct radio to radio communication. Private Call Indicates a Private Call in progress. In the Contacts list, it indicates a subscriber alias (name) or ID (number).
Sent Item Icons The following icons appear at the top right corner of the radio’s display in the Sent Items folder. Identifying Status Indicators Sent Successfully The text message is sent successfully. 10 English Send Failed The text message cannot be sent. In-Progress LED Indicators LED indicators show the operational status of your radio. Red Yellow Green • The text message to a group alias or ID is pending transmission.
Rapidly blinking yellow – Radio is actively searching for a new Audio Tones site. Blinking green – Radio is powering up, receiving a nonprivacy-enabled call or data, or detecting activity over the air. Alert tones provide you with audible indications of the radio’s status or the radio’s response to data received. Continuous Tone A monotone sound. Sounds continuously until termination. Rapidly blinking green – Radio is receiving a privacy-enabled call or data.
Indicator Tones High pitched tone Receiving and Making Calls Low pitched tone Positive Indicator Tone Receiving and Making Calls Negative Indicator Tone 12 English Once you understand how your MOTOTRBO Mobile is configured, you are ready to use your radio. Use this navigation guide to familiarize yourself with the basic Call features: Selecting a Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12 Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a Zone Channel Rocker Use the following procedure to select a zone. Procedure: Press the programmed Zone button and proceed to Step 3. OR Follow the procedure below. 1 S to access the menu. 2 Por Q to Zone and press N to select. 3 The current zone is displayed and indicated by a . 4 Por Q to the required zone and press N to select. 5 The display shows Selected momentarily and returns to the selected zone screen.
Receiving and Responding to a Radio Call To receive a call from a group of users, your radio must be configured as part of that group. Receiving and Making Calls Once the channel, subscriber alias or ID, or group alias or ID is displayed, you can proceed to receive and respond to calls. The green LED lights up while the radio is transmitting and blinks when the radio is receiving. Procedure: When you receive a Group Call (while on the Home screen): 1 The green LED blinks.
5 Wait for the Talk Permit Tone to finish (if enabled) and Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone. Receiving and Responding to a Private Call A Private Call is a call from an individual radio to another individual radio. 6 Release the PTT button to listen. There are two types of Private Calls. The first type, where a radio presence check is performed prior to setting up the call, while the other sets up the call immediately.
3 If the Channel Free Indication feature is enabled, you will Receiving and Making Calls hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond to the call. OR If the Voice Interrupt feature is enabled, press the PTT button to stop the current call from the transmitting radio and free the channel for you to talk/respond. 4 The green LED lights up.
Receiving and Responding to a Phone Call Phone Call as Private Call Procedure: When you receive a Phone Call as a Group Call: 1 The first line of the display shows the RSSI icon. The second line of the display shows Phone Call which alternates with the group alias, and the Phone Call icon. Procedure: When you receive a Phone Call as a Private Call: 2 Press the PTT button to talk and release it to listen. The 1 The first line of the display shows the RSSI icon. The 3 Press R to end the call.
Phone Call as All Call Procedure: When you receive a Phone Call as an All Call: 1 The first line of the display shows the RSSI icon. The second line of the display shows Phone Call which alternates with All Call, and the Phone Call icon. 2 Press the PTT button to talk and release it to listen. The Receiving and Making Calls RSSI icon disappears during transmission. 3 Press R to end the call.
Making a Call with the Channel Rocker 4 Release the PTT button to listen. When the target radio Making a Group Call To make a call to a group of users, your radio must be configured as part of that group. Procedure: 1 Press the Channel Rocker to select the channel with the active group alias or ID. 2 Press the PTT button to make the call. The green LED lights up. The display shows the group alias or ID, and the Group Call icon.
Making a Private Call While you can receive and/or respond to a Private Call initiated by an authorized individual radio, your radio must be programmed for you to initiate a Private Call. Receiving and Making Calls You will hear a negative indicator tone, when you make a Private Call via the Menu, Call Log, Contacts list, One Touch Access button, the programmed number keys, or the Channel Rocker, if this feature is not enabled. Use the Text Message or Call Alert features to contact an individual radio.
Making an All Call Procedure: 1 Press the Channel Rocker to select the channel with the active All Call group alias or ID. 2 Press the PTT button to make the call. The green LED lights up. The display shows the All Call group alias or ID, and the All Call icon. 3 Wait for the Talk Permit Tone to finish (if enabled) and speak The One Touch Access feature allows you to make a Group, Private or Phone Call to a predefined alias or ID easily.
4 Release the PTT button to listen. When the target radio Stopping a Radio Call responds, the green LED blinks. 5 If the Channel Free Indication feature is enabled, you will Receiving and Making Calls hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond. OR If there is no voice activity for a predetermined period of time, the call ends.
Talkaround The Talkaround setting is retained even after powering down. Permanent Monitor NOTE: This feature is not applicable in Capacity Plus. Procedure: Press the programmed Repeater/Talkaround button to toggle between talkaround and repeater modes. OR Follow the procedure below. 1 S to access the menu. 2 Por Q to Utilities and press N to select. 3 Por Q to Radio Settings and press N to select. 4 Por Q to Talkaround and press N to select. 5 You see Turn On if the radio is currently in Repeater mode.
Advanced Features Advanced Features Use this navigation guide to learn more about advanced features available with your radio: Radio Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 24 Remote Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 26 Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 28 Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 30 Contacts Settings . . . . . . . . . . . .
5 If the target radio is active in the system, a tone sounds and 6 Radio returns to the subscriber alias or ID screen. OR Procedure: Use the menu. 1 S to access the menu. 2 Por Q to Contacts and press N to select. 3 Por Q to the required subscriber alias or ID and press N to select. 4 Por Q to Radio Check and press N to select. 5 The display shows Radio Check: , indicating that Radio Check is in progress. The green LED lights up. 6 Wait for acknowledgement.
Remote Monitor 6 If successful: The radio starts receiving audio from the monitored radio for a programmed duration. Once the timer expires, the radio sounds an alert tone and the green LED turns off. The display shows Remote Monitor Ended. OR If unsuccessful: The radio repeats the attempt until the programmed number of tries expires. Use the Remote Monitor feature to turn on the microphone of a target radio (subscriber IDs only). No audible or visual indication is given to the target radio.
7 The display shows Remote Monitor Successful. 8 If successful: The radio starts receiving audio from the monitored radio for a programmed duration. Once the timer expires, the radio sounds an alert tone and the green LED turns off. The display shows Remote Monitor Ended. OR If unsuccessful: The radio repeats the attempt until the programmed number of tries expires. You can also manually select a target radio address (see Initiating Remote Monitor by Manual Dial on page 74).
Scan Lists Scan lists are created and assigned to individual channels/ groups. Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current channel/group. Editing the Scan List Adding a New Entry to the Scan List Procedure: 1 S to access the menu. Your radio can support up to 250 scan lists, with a maximum of 16 members in a list. Each scan list supports a mixture of both analog and digital entries. 2 Por Q to Scan and press N to select.
Deleting an Entry from the Scan List 1 S to access the menu. 2 Por Q to Scan and press N to select. 3 Por Q to View/Edit List and press N to select. 4 Por Q to the required alias or ID and press N to select. 5 Por Q to Delete and press N to select. 6 At Delete Entry?, Por Q to Yes and press N to select, to delete the entry. The display shows Entry Deleted. OR Por Q to No and press N to select to return to the previous screen. 7 Repeat Steps 4 to 6 to delete other entries.
Scan When you start a scan, your radio cycles through the programmed scan list for the current channel looking for voice activity. The yellow LED blinks and you see the scan icon on the display. During a dual mode scan, if you are on a digital channel, and your radio locks onto an analog channel, it automatically switches from digital mode to analog mode for the duration of the call. This is also true for the reverse.
Responding to a Transmission During a Scan Deleting a Nuisance Channel If a channel continually generates unwanted calls or noise (termed a “nuisance” channel), you can temporarily remove the unwanted channel from the scan list. Procedure: This capability does not apply to the channel designated as the Selected Channel.
Restoring a Nuisance Channel Procedure: To restore the deleted nuisance channel, do one of the following: • Turn the radio off and then power it on again, OR • Stop and restart a scan via the programmed Scan button or menu, OR Advanced Features • Change the channel via the Channel Rocker. 32 English Contacts Settings Contacts provides “address-book” capabilities on your radio. Each entry corresponds to an alias or ID that you use to initiate a call.
4 Press the PTT button to make the call. The green LED lights Each entry within Contacts displays the following information: 5 Wait for the Talk Permit Tone to finish (if enabled) and speak up. The display shows the group alias or ID, and the Group Call icon. • Call Type • Call Alias • Call ID NOTE: You can add, delete, or edit subscriber aliases or IDs for the Digital Contacts list. For the Analog Contacts list, you can only view the list and initiate a Call Alert.
Making a Private Call from Contacts Procedure: 1 S to access the menu. 2 Por Q to Contacts and press N to select.The entries are alphabetically sorted. 3 Por Q to the required subscriber alias or ID. 4 Press the PTT button to make the call. The green LED lights up. The first line displays the subscriber alias or ID. The second line displays Private Call and the Private Call icon. Advanced Features 5 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.
Assigning an Entry to a Programmable Number Key 1 S to access the menu. 2 Por Q to Contacts and press N to select. The entries are alphabetically sorted. 3 Por Q to the required alias or ID and press N to select. 4 Por Q to Program Key and press N to select. 5 Por Q to the desired number key and press N to select. OR If the number key is currently assigned to another entry, the display shows The Key is Already Assigned and then, the first line of the display shows Overwrite?.
Removing the Association between Entry and Programmable Number Key Procedure: You can turn on or off the ringing tones for a received Private Call. 1 S to access the menu. 1 S to access the menu. 2 Por Q to Contacts and press N to select. The 2 Por Q to Utilities and press N to select.
Activating and Deactivating Call Ringers for Text Messaging Activating and Deactivating Call Ringers for Telemetry Status with Text You can turn on or off the alert tones for a received Telemetry Status with Text. Procedure: Procedure: 1 S to access the menu. 1 S to access the menu. 2 Por Q to Utilities and press N to select. 2 Por Q to Utilities and press N to select. 3 Por Q to Radio Settings and press N to select. 3 Por Q to Radio Settings and press N to select.
Assigning Ring Styles You can program your radio to sound one of ten predefined ringing tones when receiving a Call Alert or a Text Message from a particular contact. Procedure: 1 S to access the menu. 2 Por Q to Contacts and press N to select.The entries are alphabetically sorted. 3 Por Q to the required alias or ID and press N to select. Advanced Features 4 Por Q to Ring Style and press N to select. 5 A indicates the current selected tone. 6 Por Q to the required tone and press N to select.
Call Log Features Whenever a call is missed, your radio displays a missed call message. Select View to view it immediately or View Later to view at a later time. • Store alias or ID to Contacts NOTE: The radio exits the Missed Call screen and sets up a Private Call if you press the PTT button while viewing a missed call number. • Delete Procedure: You can perform the following tasks in each of your call lists: Viewing Recent Calls The lists are Missed, Answered, and Outgoing.
Deleting a Call from a Call List Procedure: 1 S to access the menu. 2 Por Q to Call Log and press N to select. 3 Por Q to the required list and press N to select. 4 Por Q to the required alias or ID and press N to select. Call Alert paging enables you to alert a specific radio user to call you back when they are able to do so. This feature is applicable for subscriber aliases or IDs only and is accessible through the menu via Contacts or manual dial.
Making a Call Alert from the Contacts List 1 S to access the menu. Procedure: 2 Por Q to Contacts and press N to select. 1 Press the programmed One Touch Access button to make 3 Por Q to the required subscriber alias or ID and press N to select. 4 Por Q to Call Alert and press N to select. 5 The display shows Call Alert: , indicating that the Call Alert has been sent. 6 The green LED lights up when your radio is sending the Call Alert.
Emergency Operation An Emergency Alarm is used to indicate a critical situation. You are able to initiate an Emergency at any time on any screen display even when there is activity on the current channel. Your dealer can set the duration of a button press for the programmed Emergency button, except for long press, which is similar with all other buttons: • Short press – Between 0.05 seconds and 0.75 seconds Advanced Features • Long press – Between 1.00 second and 3.
You will not be able to receive any other indications or displays for any other calls until you exit the Emergency Alarm received screen. NOTE: Press R, then press Emergency Off button immediately to clear the Emergency Alarm received indications and exit Emergency mode. Press R, then press Emergency On button immediately to toggle the Emergency feature between hidden or shown. When your radio receives an Emergency Alarm, and you change the radio channel, the Emergency Alarm list is hidden.
Sending an Emergency Alarm This feature allows you to send an Emergency Alarm, a nonvoice signal, which triggers an alert indication on a group of radios. Procedure: 1 Press the programmed Emergency On button or the Emergency footswitch. 2 The display shows Sending Alarm, which alternates with your radio ID. The green LED lights up and the Emergency icon appears on the Home screen display.
6 Release the PTT button to listen. tone sounds ( if the Channel Free Indication feature is enabled). Press the PTT button to respond. OR Once your call ends, press Emergency Off button to exit the Emergency mode. 8 The radio returns to the Home screen. If your radio is set to Silent, it will not display any audio or visual indicators during Emergency mode, or allow any received calls to sound through the radio’s speaker, until you press the PTT button to initiate the call.
4 While transmitting, the green LED lights up and the Reinitiating an Emergency Mode Emergency icon appears on the display. 5 Once the hot mic duration expires, the radio automatically NOTE: This feature is only applicable to the radio sending the Emergency Alarm. stops transmitting. To transmit again, press the PTT button.
Text Messaging Features 6 The display shows Text Message: , confirming your message is being sent. Sending a Quick Text Message Your radio supports a maximum of 50 Quick Text messages as programmed by your dealer. 7 If the message is sent successfully, a tone sounds and the display shows Message Sent. OR If the message cannot be sent, the display shows Message Send Failed.
If the text message fails to send, the radio returns you to the Resend option screen (see Managing Fail-to-Send Text Messages on page 49). 3 Por Q to Drafts and press N to select. 4 Por Q to the required message and press N to select. Managing Text Messages in the Drafts Folder The Drafts folder stores a maximum of ten (10) last saved messages. When the folder is full, the next saved text message automatically replaces the oldest text message in the folder.
Managing Fail-to-Send Text Messages Forwarding a Text Message Select Forward to send the message to another subscriber/ group alias or ID. • Resend Procedure: • Forward 1 Por Q to Forward and press N to select. • Edit (Only available with a keypad microphone – see Editing a 2 Por Q to the required alias or ID and press N to Text Message on page 93 for more information) NOTE: If the channel type (i.e.
Managing Sent Text Messages Once a message is sent to another radio, it is saved in Sent Items. The most recent sent text message is always added to the top of the Sent Items list. The Sent Items folder is capable of storing a maximum of thirty (30) last sent messages. When the folder is full, the next sent text message automatically replaces the oldest text message in the folder. NOTE: Long press R at any time to return to the Home screen.
3 The display shows Sending to:
Deleting All Sent Text Messages from Sent Items Procedure: Press the programmed Text Message button and proceed to Step 3. OR Follow the procedure below. When receiving a message, the display shows the alias or ID of the sender and the message icon at the far left of the screen. 1 S to access the menu. • Read 2 Por Q to Messages and press N to select. • Read Later 3 Por Q to Sent Items and press N to select. • Delete 4 Por Q to Delete All and press N to select.
3 Press R to return to the Inbox. Press Por Q to access the Read Later or Delete option screen: • Select Read Later to return to the screen you were on prior to receiving the text message. • Select Delete to delete the text message. Text messages in the Inbox are sorted according to the most recently received. NOTE: Long press R at any time to return to the Home screen. Viewing a Text Message from the Inbox Procedure: 1 S to access the menu. 2 Por Q to Messages and press N to select.
Viewing a Telemetry Status Text Message from the Inbox Procedure: 1 S to access the menu. 2 Por Q to Messages and press N to select. 3 Por Q to Inbox and press N to select. 4 Por Q to the required message and press N to select. 5 The display shows Telemetry: . Advanced Features 6 Long press R to return to the Home screen. You cannot reply to a Telemetry Status text message.
Deleting a Text Message from the Inbox Deleting All Text Messages from the Inbox Procedure: Press the programmed Text Messaging button and proceed to Step 3. OR Follow the procedure below. 1 S to access the menu. 1 S to access the menu. 2 Por Q to Messages and press N to select. 2 Por Q to Messages and press N to select. 3 Por Q to Inbox and press N to select. 3 Por Q to Inbox and press N to select. 4 Por Q to the required message and press N to 4 Por Q to Delete All and press N to select. select.
Privacy Advanced Features If enabled, this feature helps to prevent eavesdropping by unauthorized users on a channel by the use of a softwarebased scrambling solution. The signaling and user identification portions of a transmission are not scrambled. The LED lights up solid green while the radio is transmitting and blinks green rapidly when the radio is receiving an ongoing privacy-enabled transmission. NOTE: Some radio models may not offer this Privacy feature.
IP Site Connect NOTE: This feature is not applicable in Capacity Plus. When the radio moves out of range from one site and into the range of another, it connects to the new site's base station to send or receive calls/data transmissions. Depending on your settings, this is done automatically or manually. If the radio is set to do this automatically, it scans through all available sites when the signal from the current site is weak or when the radio is unable to detect any signal from the current site.
4 Por Q to Site Roaming and press N to select. 5 Por Q to Unlock Site and press N to select. A tone sounds and the display shows Site Unlocked. 6 The radio returns to the Home screen. The display shows the site roaming icon and channel alias. 7 The yellow LED blinks rapidly when the radio is actively searching for a new site, and turns off once the radio locks on to a site. Procedure: Use the menu. 1 S to access the menu. 2 Por Q to Utilities and press N to select.
3 Por Q to Radio Settings and press N to select. 5 Por Q to Active Search and press N to select. 6 A tone sounds and the display shows Finding Site. The green LED blinks. 7 If a new site is found, a tone sounds and the LED turns off. The display shows Site Found. OR If there is no available site within range, a tone sounds and the LED turns off. The display shows Out of Range. OR If a new site is within range, but the radio is unable to connect to it, a tone sounds and the LED turns off.
OR Radio Enable Procedure: Use the menu. 1 S to access the menu. 2 Por Q to Contacts and press N to select. The entries are alphabetically sorted. 3 Por Q to the required subscriber alias or ID and press N to select. 4 Por Q to Radio Disable and press N to select. The green LED blinks. Advanced Features 5 The display shows Radio Disable:
3 Por Q to the required subscriber alias or ID and press N to select. green LED blinks. 5 The display shows Radio Enable: and the green LED lights up. 6 Wait for acknowledgment. 7 If successful, a tone sounds and the display shows Radio Enable Successful. OR If not successful, a tone sounds and the display shows Radio Enable Failed. Do not press R during the Radio Enable operation as you will not get an acknowledgement message.
Third Party Peripherals Connection Modes You can select one of the third party peripherals connection modes: Procedure: 1 S to access the menu. 2 Por Q to Utilities and press N to select. 3 Por Q to Radio Settings and press N to select. • Motorola 4 Por Q to Cable Type and press N to select. • PC and Audio 5 Por Q to the required connection mode and press N • Data Accessory to select. 6 The display shows the selected connection mode.
Utilities You can adjust your radio's squelch level to filter out unwanted calls with low signal strength or channels that have a higher than normal background noise. Settings: Normal is the default. Tight filters out (unwanted) calls and/or background noise. However, calls from remote locations may also be filtered out. Procedure: Press the programmed Squelch button to toggle squelch level between normal and tight. OR Follow the procedure below.
Turning the Option Board Feature(s) On or Off A channel can support up to 6 option board features. Refer to your dealer or system administrator for more information. Procedure: Press the programmed Option Board Feature button to toggle the feature on or off. Turning the Voice Operating Transmission (VOX) Feature On or Off Advanced Features This feature allows you to initiate a hands-free voice activated call on a programmed channel.
Turning the Public Address System On or Off Procedure: Press the programmed PA On/Off button to toggle the feature on or off. Turning the External Public Address System On or Off You can enable or disable the audio routing between the connected public address (PA) loudspeaker amplifier and the radio’s internal public address (PA) system. Procedure: Press the programmed Ext PA On/Off button to toggle the feature on or off.
Turning Horns/Lights On or Off Your radio is able to notify you of an incoming call via the horns and lights feature. When activated, an incoming call sounds your vehicle's horn and turns on its lights. Advanced Features This feature needs to be installed through your radio’s rear accessory connector by your dealer. Turning the Radio Tones/Alerts On or Off You can enable and disable all radio tones and alerts (except for the incoming Emergency alert tone) if needed.
Setting the Tone Alert Volume Offset Level Procedure: You can enable and disable the Talk Permit Tone if needed. Procedure: 1 S to access the menu. 1 S to access the menu. 2 Por Q to Utilities and press N to select. 2 Por Q to Utilities and press N to select. 3 Por Q to Radio Settings and press N to select. 3 Por Q to Radio Settings and press N to select. 4 Por Q to Tones/Alerts and press N to select. 4 Por Q to Tones/Alerts and press N to select. 5 Por Q to Talk Permit and press N to select.
Turning the Power Up Alert Tone On or Off You can enable and disable the Power Up Alert Tone if needed. Procedure: You can customize your radio’s text message alert tone to Momentary or Repetitive for each entry in the Contacts list. 1 S to access the menu. Procedure: 2 Por Q to Utilities and press N to select. 1 S to access the menu. 3 Por Q to Radio Settings and press N to select. 2 Por Q to Contacts and press N to select. 4 Por Q to Tones/Alerts and press N to select.
Turning the LED Indicators On or Off Turning the Introduction Screen On or Off You can enable and disable the Introduction Screen if needed. Procedure: Procedure: 1 S to access the menu. 1 S to access the menu. 2 Por Q to Utilities and press N to select. 2 Por Q to Utilities and press N to select. 3 Por Q to Radio Settings and press N to select. 3 Por Q to Radio Settings and press N to select. 4 Por Q to LED Indicator and press N to select. 4 Por Q to Intro Screen and press N to select.
Accessing General Radio Information Checking the Radio Alias and ID Your radio contains information on the following: Displays the ID of your radio. • Radio Alias and ID Procedure: Press the programmed Radio Alias and ID button to check your radio alias and ID. You hear a positive indicator tone. OR Follow the procedure below. • Software Version • Codeplug Version NOTE: Press R at any time to return to the previous screen or long press R to return to the Home screen.
Checking the Firmware Version Procedure: 1 S to access the menu. 2 Por Q to Utilities and press N to select. 3 Por Q to Radio Info and press N to select. 4 Por Q to Firmware Ver. and press N to select. 5 The display shows the current firmware version. Checking the Codeplug Version Displays the codeplug version on your radio. Procedure: 1 S to access the menu. 2 Por Q to Utilities and press N to select.
Using the Keypad You can use the 3 x 4 alphanumeric keypad on the keypad microphone (Motorola part number: RMN5065_) to access your radio’s features. You can use the keypad to enter subscriber aliases or IDs, and text messages. Many characters require that you press a key multiple times. The table below shows the number of times a key needs to be pressed to generate the required character. Number of Times Key is Pressed Keypad Microphone Features Key 1 2 3 4 5 6 7 8 9 10 11 12 13 1 .
Turning Keypad Tones On or Off Additional Advanced Features Procedure: Selecting a Zone by Alias Search 1 S to access the menu. Procedure: 2 Por Q to Utilities and press N to select. 1 S to access the menu. 3 Por Q to Radio Settings and press N to select. 2 Por Q to Zone and press N to select. 4 Por Q to Tones/Alerts and press N to select. 3 The current zone is displayed and indicated by a . 5 Por Q to Keypad Tones and press N to select. 4 Por Q to the required zone and proceed to Step 7.
Initiating a Radio Check by Manual Dial Procedure: 1 S to access the menu. Keypad Microphone Features 2 Por Q to Contacts and press N to select. 10 If the target radio is active in the system, a tone sounds and the display briefly shows Target Radio Available. OR If the target radio is not active in the system, a tone sounds and the display briefly shows Target Radio Not Available. 3 Por Q to Manual Dial and press N to select. 11 Radio returns to the subscriber ID screen.
6 If there is a previously dialed subscriber ID, the ID appears 7 Por Q to Remote Mon. and press N to select. 8 Wait for acknowledgment. 9 The display shows Remote Monitor Successful. OR The display shows Remote Monitor Failed. 10 If successful: Once the timer expires, the radio sounds an alert tone and the green LED turns off. The display shows Remote Monitor Ended. OR If unsuccessful: The radio repeats the attempt until the programmed number of tries expires.
9 Release the PTT button to listen. When the target radio responds, the green LED blinks. Keypad Microphone Features 10 If the Channel Free Indication feature is enabled, you will 76 hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond. OR If there is no voice activity for a programmed period of time, the call ends. 11 You hear a short tone. The display shows Call Ended.
9 Press R to end the call. If deaccess code was not preconfigured in the Contacts list, the first line of the display shows De-Access Code:. The second line of the display shows a blinking cursor. Enter the deaccess code and press N to proceed. The radio returns to the previous screen. 10 The DTMF tone sounds and the display shows Ending Phone Call. 11 If successful: A tone sounds and the display shows Phone Call Ended. Your radio returns to the Call Phone screen.
Making a Phone Call with the One Touch Access Button Procedure: Keypad Microphone Features 1 Press the programmed One Touch Access button to make a Phone Call to the predefined alias or ID. If the entry for the One Touch Access button is empty, a negative indicator tone sounds. If the access code was not preconfigured in the Contacts list, the first line of the display shows Access Code:. The second line of the display shows a blinking cursor. Enter the access code and press N to proceed.
When the telephone user ends the call, a tone sounds and the display shows Phone Call Ended. If the call ends while you are entering the extra digits requested by the Phone Call, your radio returns to the screen you were on prior to initiating the call. NOTE: During channel access, press R to dismiss the call attempt and a tone sounds.
4 Release the PTT button to listen. When the target radio responds, the green LED blinks. Keypad Microphone Features 5 If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond. OR If there is no voice activity for a predetermined period of time, the call ends. 6 Radio returns to the screen you were on prior to initiating the call.
5 Press the PTT button to talk and release it to listen. The 6 Press R to end the call. If deaccess code was not preconfigured in the Contacts list, the first line of the display shows De-Access Code:. The second line of the display shows a blinking cursor. Enter the deaccess code and press N to proceed. The radio returns to the previous screen. 7 The DTMF tone sounds and the display shows Ending If unsuccessful: Your radio returns to the Phone Call screen.
Making a Phone Call from Contacts Procedure: 1 S to access the menu. 2 Por Q to Contacts and press N to select.The entries are alphabetically sorted. 3 Por Q to the required subscriber alias or ID. Keypad Microphone Features OR Por Q to Manual Dial and press N to select. Por Q to Phone Number and press N to select. The first line of the display shows Phone Number:. The second line of the display shows a blinking cursor. Use the keypad to enter a telephone number. 4 Press N to select.
9 Press R to end the call. If the call ends while you are entering the extra digits requested by the Phone Call, your radio returns to the screen you were on prior to initiating the call. NOTE: During channel access, press R to dismiss the call attempt and a negative indicator tone sounds. Your radio returns to the Call Phone screen. 10 The DTMF tone sounds and the display shows Ending Phone Call. 11 If successful: A tone sounds and the display shows Phone Call Ended.
Making a Group, Private, Phone or All Call by Alias Search You can also use alias or alphanumeric search to retrieve the required subscriber alias. This feature is only applicable while in Contacts. Keypad Microphone Features Procedure: 1 S to access the menu. 2 Por Q to Contacts and press N to select. The entries are alphabetically sorted. 3 Key in the first character of the required alias. 4 A blinking cursor appears. Use the keypad to type the required alias. Press P to move one space to the left.
Viewing an Entry in the Scan List by Alias Search Editing the Scan List by Alias Search 1 S to access the menu. 2 Por Q to Scan and press N to select. 3 Por Q to View/Edit List and press N to select. 4 Key in the first character of the required alias. 5 A blinking cursor appears. Use the keypad to type the required alias. Press P to move one space to the left. Press Q to move one space to the right. Press the *DEL key to delete any unwanted characters.
10 The display shows Entry Saved, followed immediately by Add Another?. 11 Por Q to Yes and press N to select, to add another Keypad Microphone Features entry, and repeat Steps 5 to 9. OR Por Q to No and press N to select to save the current list. Deleting an Entry from the Scan List Procedure: 1 S to access the menu. 2 Por Q to Scan and press N to select. 6 The first line of the display shows the characters you keyed in. The second line of the display shows the required alias.
Setting and Editing Priority for an Entry in the Scan List 10 The display shows Entry Saved before returning to the previous screen. 11 The priority icon appears left of the member’s name. 1 S to access the menu. There is no priority icon if priority is set to None. 2 Por Q to Scan and press N to select. 3 Por Q to View/Edit List and press N to select. Storing an Alias or ID from the Missed Call List Procedure: 4 Key in the first character of the required alias. 1 S to access the menu.
Making a Call Alert by Manual Dial Procedure: 1 S to access the menu. 2 Por Q to Contacts and press N to select. 3 Por Q to Manual Dial and press N to select. Keypad Microphone Features 4 Por Q to Radio Number and press N to select. 5 The first line of the display shows Radio Number:. 6 A blinking cursor appears. Enter the subscriber ID you want to send the Call Alert to and press N. 7 Por Q to Call Alert and press N to select.
5 Press N once message is composed. OR Por Q to Save and press N to save the message to the Drafts folder. OR R to edit the message. R again to delete the message or save it to the Drafts folder. 7 Por Q to the required subscriber alias or ID and press N to select. OR Por Q to Manual Dial and press N to select. The first line of the display shows Radio Number:. Key in the subscriber ID and press N. 8 The display shows Text Message: , confirming your message is being sent.
7 Por Q to Write and press N to select. Keypad Microphone Features A blinking cursor appears. Use the keypad to type your message. Press P to move one space to the left. Press Q or the # key to move one space to the right. Press the * key to delete any unwanted characters. Editing a Quick Text Message Procedure: Press the programmed Text Messaging button and proceed to Step 3. OR Follow the procedure below. 8 Press N once message is composed. 1 S to access the menu.
7 Por Q to Send and press N to send the message. OR Accessing the Drafts Folder You can save a text message to send it at a later time. the Drafts folder. OR R to edit the message. R again to delete the message or save it to the Drafts folder. If a PTT button press or a mode change causes the radio to exit the text message writing/editing screen while you are in the process of writing or editing a text message, your current text message is automatically saved to the Drafts folder.
3 Por Q to the required alias or ID and press N to select. OR Por Q to Manual Dial and press N to select. The first line of the display shows Radio Number:. Key in the subscriber alias or ID and press N. 4 The display shows Sending to: , confirming your message is being sent. 5 If the message is sent, a tone sounds and the display shows Message Sent. OR If the message is not sent, a low tone sounds and the display shows Message Send Failed.
Editing a Text Message NOTE: If a subject line is present (for messages received from an e-mail application), you cannot edit it. Message Sent. OR If the message is not sent, a low tone sounds and the display shows Message Send Failed. Procedure: 1 Por Q to Edit and press N to select. 2 A blinking cursor appears beside the message. Use the keypad to edit your message. Press P to move one space to the left. Press Q or the # key to move one space to the right.
Security Radio Enable via Manual Dial Procedure: Radio Disable via Manual Dial Procedure: 1 S to access the menu. Keypad Microphone Features 2 Por Q to Contacts and press N to select. The 94 entries are alphabetically sorted. 3 Por Q to Manual Dial and press N to select. Por Q to Radio Number and press N to select. The first line of the display shows Radio Number:. Key in the subscriber ID and press N. 4 Por Q to Radio Disable and press N to select. The green LED blinks.
Password Lock Features Accessing the Radio from Password Procedure: Power up the radio. 1 You hear a continuous tone. The first line of the display shows Enter Password:. The second line of the display shows a blinking cursor. 2 Enter a four-digit password via keypad microphone. You hear a positive indicator tone for every digit pressed. OR Press the Channel Rocker to select a digit and N to enter the selected digit. Enter the remaining digits of the password in the same manner.
Unlocking the Radio from Locked State Procedure: Wait for 15 minutes. Repeat Steps 1 to 3 in Accessing the Radio from Password on page 95. OR Power up the radio, if you have powered down the radio during locked state: Keypad Microphone Features 1 A tone sounds and the yellow LED double blinks. The display shows Radio Locked. 2 Wait for 15 minutes. Repeat Steps 1 to 3 in Accessing the Radio from Password on page 95. Your radio restarts the 15 minutes timer for locked state when you power up.
Changing the Password 1 S to access the menu. 2 Por Q to Utilities and press N to select. 3 Por Q to Radio Settings and press N to select. 4 Por Q to Passwd Lock and press N to select. OR Press the Channel Rocker to select a digit and N to enter the selected digit. Enter the remaining digits of the password in the same manner. The second line of the display shows ****. Press N to proceed. You hear a negative indicator tone, if you press more than four digits.
