PIP1610 HD CONNECT 5.
Welcome... to your new Motorola Wi-Fi® Video Baby Monitor! Thank you for purchasing the Wi-Fi® Video Baby Monitor. Now you can see and hear your baby sleeping in another room or you can monitor your older children in their play room. Our Connected Baby Monitor let you see your baby from the hand-held viewer, or from your smartphone. Watch over and communicate with your baby from anywhere in the world. Please keep your original dated sales receipt for your records.
Overview of the Parent Unit 3 9 2 5 1 6 4 7 8 1. 2. Display (LCD screen) Parent Unit ON/OFF and Screen ON/OFF Button - Press and hold to switch the parent unit ON/OFF. - Single press to switch the screen ON/OFF. 3. Audio Level LEDs (Green, Green, Amber, Red, Red) 4. Navigation Button - Press Left/Right to pan the camera left or right. - Press Up/Down to tilt the camera upward or downward. - Press Left and Right to select parent unit volume level.
11 12 10 10. Fixed stand 11. Antenna 12.
Overview of Your Baby Unit 6 1 2 3 8 4 7 9 10 5 Photo sensor (Night Vision Mode) 2. Camera lens 3. Infrared LEDs under the camera lens (x 8, for night vision) 4. High sensitivity microphone 1. 5. 6. 7. 8. 9. 10.
Table of contents 1. Safety Instructions...........................................................................8 2. Getting Started............................................................................... 10 2.1 2.2 2.3 2.4 2.5 Connecting the Power Supply for the Baby Unit.......................10 Fixing magnetic mount on the wall.................................................10 Connecting the Power Supply of the Parent Unit....................... 11 Desktop Stand of the Parent Unit..........
4.8 Power Saving mode...............................................................................18 4.9 View multiple cameras on screen ....................................................18 5. Viewing the baby through your device..................................... 19 5.1 Minimum System Requirements........................................................19 5.2 Connecting Devices................................................................................19 5.3 Setup the camera......................
1. Safety Instructions WARNING: Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3ft (1m) away). Never use extension cords with AC Adapters. Only use the AC Adapters provided.
Wi-Fi® CAMERA UNIT SET UP & USE: • • • Choose a location for the Baby Unit that will provide the best view of your baby in his/her crib. Place the Baby Unit on a flat surface, such as a dresser, bureau or shelf, or mount the Baby Unit on a wall securely using the keyhole slots in the underside of the stand. NEVER place the Baby Unit or cords within the crib.
2. Getting Started 2.1 Connecting the Power Supply for the Baby Unit • Insert the DC plug of the power adapter into the DC socket on the back of the Baby Unit. • Connect the other end of the power adapter to a suitable electrical outlet. • The baby unit turns on and the power indicator lights up blue. Note Only use the supplied power adapter (DC5V/1500mA). 2.2 Fixing mount to the wall Screw Screw • Mark the position of the screw holes on the wall.
2.3 Connecting the power supply of the Parent Unit Power Button • Connect the DC plug of the power adapter to the parent unit and the other end to the electrical outlet. Only use the enclosed adapter (5VDC/1500mA). • Press and hold the POWER button on the Parent Unit to turn it ON. NOTE • A rechargeable battery (Lithium ion battery 2800mAh) inside the Parent Unit allows you to move it without losing the link and picture from the Baby Unit. The battery provides up to 7 hours operation of the Parent Unit.
2.5 Registration (Pairing) The Baby Monitor is pre-registered to your Parent Unit. You do not need to register it again unless the Baby Unit loses its link with the Parent Unit. To re-register your Baby Unit, or register a new Baby Unit, follow the procedures below: 1. Press the M button and the menu bar will pop up. 2. Press the < LEFT button or > RIGHT button until is highlighted, and the del/ add/ view/ scan menu will pop up. 3.
3. Using the Baby Monitor 3.1 Setting Up Place the Baby Unit in a convenient location (e.g. on a table) and point the camera lens towards the area you want to monitor. Adjust the angle of the Baby Unit's camera until you are satisfied with the image shown on the Parent Unit. NOTE Do not place the Baby Unit within the baby's reach! If there is interference with the picture or sound, try moving the units to different locations, and ensure they are not close to other electrical equipment. 3.
3.6 Temperature Display (HH °C / °F or LL °C / °F) The temperature reading from the temperature sensor at the back of the Baby Unit will be displayed at the top of the LCD screen. The readings will turn RED if the temperature goes above 29°C / 84°F or below 14°C / 57°F. The reading will change to HH °C / °F if the temperature goes above 36°C / 97°F. The reading will change to LL °C / °F if the temperature goes below 1°C / 34°F. 4. Parent Unit Menu Options 4.
2. Scroll + Up or - Down to select then confirm with O button. 3. Press + UP button or - DOWN button to view the desired Lullaby/Soothing Sounds. The song names appear on the screen. 4. Press O button to play the selection. 4.4.2 Audio Book (English only) Playback 4.4.3 Personal Recording Playback 1. Tap on M button then Scroll Left/Right to select option at the menu bar. 2. Scroll + Up or - Down to select then confirm with O button. 3.
4. If an alarm time is selected, the Parent Unit will beep for about 45 seconds after every 6, 4 or 2 hour period. 4.6 Camera Control 4.6.1 Add (pair) a camera 1. 2. Press the M button and the menu bar will pop up. Press the < LEFT button or > RIGHT button until is highlighted, and the del/ add/ view/ scan menu will pop up. 3. Press the + UP button or - DOWN button to select add, and press the O button to confirm. 4. Camera / / / will pop up.
TIP You can also press the O button repeatedly to select the avail/ / / , scan. able camera options from 4.6.3 Delete a camera 1. 2. Press the M button and the menu bar will pop up. is Press the < LEFT button or > RIGHT button until highlighted, and the del/ add/ view/ scan menu will pop up. del, and 3. Press the + UP button or - DOWN button to select press the O button to confirm. 4. Camera / / / will pop up, press the + UP button or - DOWN button to select the desired Camera, and press the O button. 5.
4.7 Temperature 1. Press the M button and the menu bar will pop up. 2. Press the < LEFT button or > RIGHT button until highlighted. Press O, then +UP / -DOWN to select °C or °F. 3. 4.8 1. 2. 3. is Power Saving mode Press the M button and the menu bar will pop up. Press the < LEFT button or > RIGHT button until V is highlighted. Press the + UP button or - DOWN button to select auto video off after 5 mins, 30 mins or 60 mins (if operating on batteries only)..
5. Viewing the baby through your device 5.1 Minimum System Requirements Android™ System • Version 7.0 or above iPhone®/iPad® iOS • Version 10.0 or above High Speed (Wi-Fi®) Internet • At least 0.6 Mbps upload bandwidth per camera (you can test your internet speed on this site: http://www.speedtest.net). 5.
5.3 Set up the camera Connect the Wi-Fi® camera (baby unit) to the power adaptor, then plug into the wall socket. The camera must be within range of the Wi-Fi® router with which you want to connect. Make sure the password of the router is available for entering during the in-app setup process. The following table shows the meanings of different LED connection status. State LED indication Pair / Setup Flashes blue and red Connected Solid blue Video streaming Flashes blue 5.3.
5.3.4 1. Sign up or log in to the App Ensure that your smart device is connected to your Wi-Fi® router. 2. Follow the on-screen instructions to run and sign up or log in to the APP. 5.3.5 1. Add a camera to your account Log in to the APP. 2. Tap Devices, and then tap on the device screen to add a new camera. 3. Tap (your baby monitor model's name) to add the new camera. 4. Select and enter the password of your Wi-Fi® network and then tap Next. 5. Power on the camera. 6.
6. Help No display • Try recharging the battery pack. • Reset the parent and baby (camera) units. Unplug both the units' from the wall socket, then plug them back in. • Check if the parent/baby (camera) unit is switched on. • Press and hold the power button on the parent unit to switch it on. • Make sure the correct camera is selected. Change the camera number if necessary. • Make sure the display of the parent unit is turned on.
Noise interference on your device • To avoid background noise or echoes, ensure there is enough distance between your device and the Wi-Fi® camera (baby unit). • Use of other 2.4 GHz products, such as wireless networks (Wi-Fi® routers), Bluetooth™ systems, or microwave ovens, may cause interference with this product. Keep the parent and baby (camera) units at least 5 feet away from these types of products, or switch them off if they appear to be causing interference.
7. General information Cleaning and care Important Always switch off and disconnect the power adaptor before cleaning your video baby monitor. • Clean your video baby monitor with a slightly damp cloth or with an antistatic cloth. Never use cleaning agents or abrasive solvents. • Do not clean any part of the video baby monitor with thinners or other solvents and chemicals - this may cause permanent damage to the product which is not covered by the warranty.
Who is covered? This warranty extends only to the first consumer purchaser, and is not transferable. What will MZGW do? MZGW or its authorized distributor at its option and within a commercially reasonable time, will at no charge repair or replace any Products or Accessories that do not conform to this limited warranty. We may use functionally equivalent reconditioned / refurbished / pre-owned or new Products, Accessories or parts.
Exclusions Normal Wear and Tear. Periodic maintenance, repair and replacement of parts due to normal wear and tear are excluded from coverage. Batteries. Only batteries whose fully charged capacity falls below 80% of their rated capacity and batteries that leak are covered by this limited warranty. Abuse & Misuse. Defects or damage that result from: (a) improper operation, storage, misuse or abuse, accident or neglect, such as physical damage (cracks, scratches, etc.
FCC and IC regulations FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement: The baby unit complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with minimum distance 20cm between the radiator& your body. The parent unit has been tested and comply with FCC and ISED SAR limits. Déclaration d'exposition aux radiations: L'unité bébé est conforme aux limites d'exposition aux rayonnements FCC / ISED établies pour un environnement non contrôlé.
8. Technical Specifications RF frequency bands Parent unit display Temperature Operating range Baby unit image sensor Power adaptor for the baby unit and the parent unit Parent unit battery information Battery life 2400 MHz to 2483.5MHz 5.0” diagonal TFT LCD 0°C ~ 40°C or 32°F ~ 104°F Color CMOS 2M Pixels Input: 100-240V AC, 50/60Hz, 300mA or 400mA; Output: 5.0V DC, 1500mA Amperex Technology Limited 3.
EU Declaration of Conformity (DoC) Hereby, Meizhou Guo Wei Electronics Co. LTD declares that the product is in compliance with RE Directive 2014/53/EU. The full text of the EU declaration of conformity is available on the website: motorolanursery.com Manufactured, distributed or sold by Meizhou Guo Wei Electronics Co. LTD., official licensee for this product. MOTOROLA and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC. and are used under license.
