MN002894A01_final.
MN002894A01_final.book Page 2 Wednesday, January 4, 2017 5:32 PM Open Source Software Legal Notices: This Motorola Solutions product contains Open Source Software. For information regarding licenses, acknowledgements, required copyright notices and other usage terms, refer to the documentation for this Motorola Solutions product at: http://businessonline.motorolasolutions.com Go to: Resource Center > Product Information > Manual > Accessories.
MN002894A01_final.book Page 1 Wednesday, January 4, 2017 5:32 PM CONTENTS 1 CONTENTS Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Product Safety . . . . . . . . . . . . . . . . . . . . . . . .5 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .6 Package Contents . . . . . . . . . . . . . . . . . . . . . .6 FCC Licensing Information . . . . . . . . . . . . .7 Interference Information . . . . . . . . . . . . . . . . .7 Canada Licensing Information. . . . . . . . . . .
CONTENTS MN002894A01_final.book Page 2 Wednesday, January 4, 2017 5:32 PM English READING THE DISPLAY . . . . . . . . . . . . . . .28 Selecting a Channel . . . . . . . . . . . . . . . . . . .28 Talking and Monitoring . . . . . . . . . . . . . . . . .29 Receiving a Call . . . . . . . . . . . . . . . . . . . . . .29 Signal strength indicator and channel busy indicators . . . . . . . . . . . . . . . . . . . . . . . . . .29 Talk Range . . . . . . . . . . . . . . . . . . . . . . . . . .
MN002894A01_final.book Page 3 Wednesday, January 4, 2017 5:32 PM Block Event . . . . . . . . . . . . . . . . . . . . . . . . . 50 Event Code . . . . . . . . . . . . . . . . . . . . . . . . . 50 The Critical Events Table . . . . . . . . . . . . . . . 50 Geographic Filter . . . . . . . . . . . . . . . . . . . . . 52 State. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 County . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 FIPS . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS MN002894A01_final.book Page 4 Wednesday, January 4, 2017 5:32 PM English Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 Programming Customized Frequencies On RDU4160 . . . . . . . . . . . . . . . . . . . . . . . . . .69 CTCSS and PL/DPL Codes . . . . . . . . . . . . .70 Accessories . . . . . . . . . . . . . . . . . . . . . . . . .75 Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Audio Accessories. . . . . . . . . . . . . . . . . . . . .75 Battery . . . .
MN002894A01_final.book Page 5 Wednesday, January 4, 2017 5:32 PM PRODUCT SAFETY ! Caution PRODUCT SAFETY PRODUCT SAFETY AND RF EXPOSURE COMPLIANCE For a list of Motorola Solutions-approved antennas, batteries and other accessories, visit the following website which lists approved accessories: www.motorolasolutions.com/RDX Before using this product, read the operating instructions and RF energy awareness information contained in the Product Safety and RF Exposure booklet enclosed with your radio.
MN002894A01_final.book Page 6 Wednesday, January 4, 2017 5:32 PM INTRODUCTION INTRODUCTION Thank you for purchasing the Motorola Solutions® RDX Series™ Radio. This radio is a product of Motorola Solutions' 80 plus years of experience as a world leader in the designing and manufacturing of communications equipment. The RDX Series radios provide cost-effective communications for businesses such as retail stores, restaurants, schools, construction sites, manufacturing, property and hotel management and more.
MN002894A01_final.book Page 7 Wednesday, January 4, 2017 5:32 PM To transmit on these frequencies, you are FCC LICENSING INFORMATION required to have a license issued by the FCC. Application is made available on FCC Form This device complies with Part 15 of the FCC 601 and Schedules D, H, and Remittance Form 159. Rules. Operation is subject to the condition that To obtain these FCC forms, request document this device does not cause harmful 000601 which includes all forms and interference.
FCC LICENSING INFORMATION MN002894A01_final.book Page 8 Wednesday, January 4, 2017 5:32 PM Before filling out your application, you must Replacement of any transmitter component decide which frequency(ies) you can operate (crystal, semiconductor and more.) not on. See “Frequencies and Code Charts”. For authorized by the FCC equipment authorization questions on determining the radio frequency, for this radio could violate FCC rules.
MN002894A01_final.book Page 9 Wednesday, January 4, 2017 5:32 PM CANADA LICENSING INFORMATION The operation of your Motorola Solutions radio is subject to the Radiocommunications Act and must comply with rules and regulations of the Federal Government’s department of Industry Canada. Industry Canada requires that all operators using Private Land Mobile frequencies obtain a radio license before operating their equipment.
BATTERIES AND CHARGERS SAFETY INFORMATION MN002894A01_final.book Page 10 Wednesday, January 4, 2017 5:32 PM BATTERIES AND CHARGERS SAFETY INFORMATION 3. and cord, pull by the plug rather than the cord when disconnecting the charger. 4. extension cord could result in risk of fire and electric shock.
MN002894A01_final.book Page 11 Wednesday, January 4, 2017 5:32 PM OPERATIONAL SAFETY GUIDELINES Turn the radio OFF when charging battery. • The charger is not suitable for outdoor use. Use located at the bottom of the charger. • Make sure that the cord is located where it will not be stepped on, tripped over, or subjected to water, damage, or stress. only in dry locations/conditions.
MN002894A01_final.
MN002894A01_final.book Page 13 Wednesday, January 4, 2017 5:32 PM On/Off/Volume Knob Used to turn the radio ON or OFF and to adjust the radio’s volume. Programmable Button A Programmable Button A Used to switch the radio to different channels. Accessory Connector Used to connect compatible audio accessories. Model Label Menu Button Menu Button • Indicates the model of the radio. Microphone Speak clearly into the microphone when sending a message.
RADIO OVERVIEW MN002894A01_final.book Page 14 Wednesday, January 4, 2017 5:32 PM channel and the radio will play a good chirp. You can assign different functions to these buttons via the CPS. For example: Backlight Time Out, Reverse Burst, Scan/Nuisance Channel Delete, Monitor and Call Tones. To learn more about how to program these buttons, refer to “Advanced Configuration Mode” on page 36 and “Customer Programming Software (CPS)” on page 44.
MN002894A01_final.book Page 15 Wednesday, January 4, 2017 5:32 PM Table 1: RDX Series Radio Specifications Frequency Band Transmit Power (W) Number of Channels Antenna RDU4160 UHF 4 16 Removable RDU4163 UHF 4 16 Removable BATTERY FEATURES RDX Series radios provide Lithium-Ion batteries that come in different capacities that defines the battery life. About the Li-Ion Battery The RDX Series radio comes equipped with a rechargeable Li-Ion battery.
RADIO OVERVIEW MN002894A01_final.book Page 16 Wednesday, January 4, 2017 5:32 PM English Motorola Solutions batteries are designed specifically to be used with a Motorola Solutions charger and vice versa. Charging in non-Motorola Solutions equipment may lead to battery damage and void the battery warranty. The battery should be at about 77 °F (25 °C) (room temperature), whenever possible.
MN002894A01_final.book Page 17 Wednesday, January 4, 2017 5:32 PM recycling options for consumers, businesses, and governmental agencies. radio until a click is heard. Note: Installing the Lithium-Ion (Li-Ion) Battery Removing the Lithium-Ion (Li-Ion) Battery Battery Latch RADIO OVERVIEW Battery Latch To learn about the Li-Ion Battery Life features, refer to “About the Li-Ion Battery” on page 15 Slots 1. Turn OFF the radio. 2.
MN002894A01_final.book Page 18 Wednesday, January 4, 2017 5:32 PM Removing the Antenna 1. 1. RADIO OVERVIEW Attaching the Antenna Align the threaded end of the antenna with the radio’s antenna connector. 2. English Turn the antenna clockwise to fasten it. 18 Turn the antenna counter-clockwise until you can remove it. Note: These instructions apply ONLY to models RDU4100 and RDV5100. Do not attempt to remove the antenna if your radio is not one of these models.
MN002894A01_final.book Page 19 Wednesday, January 4, 2017 5:32 PM Installing Spring Action Belt clip. Power Supply, Adaptor and Drop-in Tray Charger Belt Clip Tab Drop-in Tray Charger Power Supply The radio is equipped with one Drop-in Tray Charger and one Power Supply with Adaptor. For more information, refer to “Chargers” on page 76. 1.
MN002894A01_final.book Page 20 Wednesday, January 4, 2017 5:32 PM Battery Life Information RADIO OVERVIEW When the Battery Save feature is set to ON (enabled by default), the battery life lasts English longer. The following table summarizes battery life estimations: Table 2: Li-Ion Battery Life with Battery Save feature ON Note: Battery Type 5W 4W High Capacity 15 hr 15 hr Battery life is estimated based on 5% transmit / 5% receive / 90% standby standard duty cycle.
MN002894A01_final.book Page 21 Wednesday, January 4, 2017 5:32 PM Charging the Battery The RDX Series radio offers two types of Chargers: Standard Charger and, • Rapid Charger Note: The radio comes with a Standard Power Supply. To charge the battery (with the radio attached), place it in a Motorola Solutions-approved Dropin Tray Single Unit Charger or Drop-in Tray Multi Unit Charger.
MN002894A01_final.book Page 22 Wednesday, January 4, 2017 5:32 PM RADIO OVERVIEW Note: When charging a battery attached to the radio, turn the radio OFF to ensure a full charge. See “Operational Safety Guidelines” on page 11 for more information. Charging A Stand-Alone Battery To charge only the battery - at step 4 on page 21, insert the battery into the tray, with the inside surface of the battery facing the front of the Drop-in Tray Single Unit Charger as shown above.
MN002894A01_final.
MN002894A01_final.
MN002894A01_final.book Page 25 Wednesday, January 4, 2017 5:32 PM Estimated Charging Time information, see “Audio Accessories” on page 75. The following table provides the estimated charging time of the battery.
MN002894A01_final.book Page 26 Wednesday, January 4, 2017 5:32 PM RADIO OVERVIEW Charging a Radio and Battery using a Multi Unit-Charger - MUC (Optional Accessory) The Multi-Unit Charger (MUC) allows drop-in charging of up to six radios or batteries. Batteries can be charged with the radios or removed and placed in the MUC separately. Each of the six charging pockets can hold a radio (with or without the Holster) or battery, but not both. 1. Place the Multi-Unit Charger on a flat surface. 2.
MN002894A01_final.book Page 27 Wednesday, January 4, 2017 5:32 PM Multi-Unit Charger LED Indicators Table 6: MUC Charger LED Indicator Status LED Indicator Comments Steady Red Indication The charger is currently charging Charging Complete Steady Green Indication Battery is fully charged Battery Fault (*) Blinking red (fast) Battery was faulty when inserted (*) Normally, re-positioning the battery pack will correct this issue.
MN002894A01_final.book Page 28 Wednesday, January 4, 2017 5:32 PM GETTING STARTED GETTING STARTED For the following explanations, refer to “Parts Of The Radio” on page 12. Keypad Lock Scan Scramble Vox / iVox Battery Level TURNING RADIO ON/OFF To turn ON the radio, rotate the On/Off/Volume Knob clockwise.
MN002894A01_final.book Page 29 Wednesday, January 4, 2017 5:32 PM TALKING AND MONITORING It is important to monitor for traffic before transmitting to avoid ‘talking over’ someone who is already transmitting • To listen to all activity on a current channel, short press the SB1 to set the CTCSS/DPL code to 0. This feature is called ‘CTCSS/DPL Defeat (Squelch set to SILENT)’. • (*) This assumes SB1 is not being programmed for a different mode. RECEIVING A CALL 1. 4.
MN002894A01_final.book Page 30 Wednesday, January 4, 2017 5:32 PM TALK RANGE 4. transmissions sound garbled to anyone GETTING STARTED TALK RANGE Model UHF 4W listening who is not set to that specific code. Industrial Multi-Level Inside steel/ concrete Industrial buildings Inside multilevel buildings Up to 350,000 ft2 Up to 30 Floors Channel: Current channel that the radio is using, depending on radio model. 2. Frequency: The frequency the radio uses to 3.
MN002894A01_final.
MN002894A01_final.book Page 32 Wednesday, January 4, 2017 5:32 PM HANDS-FREE USE/VOX 3. Insert the audio accessory’s plug firmly into 4. Turn radio ON. The LED Indicator will blink 5. Lower radio volume BEFORE placing 6. To transmit, speak into accessory microphone 7. VOX can be temporarily disabled by pressing GETTING STARTED accessory port. double red VOX Accessory accessory near ear. and to receive, stop talking.
MN002894A01_final.book Page 33 Wednesday, January 4, 2017 5:32 PM PTT button. • A short press of the PTT Button re-enables iVOX Note: There is a short delay between the time when you • For more information on setting VOX/iVOX start talking and when the radio transmits. Silent (Audible tones disabled) RESET TO FACTORY DEFAULTS Reset to Factory Defaults will set back all radio features to the original factory default settings.
MN002894A01_final.book Page 34 Wednesday, January 4, 2017 5:32 PM GETTING STARTED MENU OPTIONS To access the radio MENU, short press the (Menu) button. The radio displays the feature options. For each options, use the and buttons to navigate. After selecting your desired option settings, you can: • Press (Menu) button to save and go to the next option, or • Long press the PTT button to save and exit, or • Turn OFF the radio to exit without saving the changes.
MN002894A01_final.book Page 35 Wednesday, January 4, 2017 5:32 PM • Press the (Menu) button to go to the next step, or • Turn OFF the radio to exit without saving changes. GETTING STARTED Note: The default sensitivity is ‘Medium’ for VOX and ‘High’ for iVOX. MICROPHONE GAIN The sensitivity of the microphone can be adjusted to fit different users or operating environments. This feature can be adjusted only through the CPS. Microphone default setting is set to level 2 (medium gain).
PROGRAMMING FEATURES MN002894A01_final.book Page 36 Wednesday, January 4, 2017 5:32 PM PROGRAMMING FEATURES Advanced Configuration Mode ADVANCED CONFIGURATION MODE Advanced Configuration is a configuration mode that allows the customization of additional features via the radio’s front panel. Entering Advanced Configuration Mode To enter Advanced Configuration Mode, press and hold the PTT Button and the SB1 Button simultaneously for 3 s, while turning ON the radio.
MN002894A01_final.book Page 37 Wednesday, January 4, 2017 5:32 PM When in ‘Idle’ Programming Mode, long press the PTT button to exit the Programming Mode. • Whenever you wrap around to the beginning of the Programming Mode options, the radio automatically saves all changes made, even if you turn OFF the radio. • Exit the Programming Mode without saving changes (as long as you have not wrapped around to the beginning of the Programming Mode options) by turning OFF the radio.
MN002894A01_final.book Page 38 Wednesday, January 4, 2017 5:32 PM PROGRAMMING FEATURES PROGRAMMING SCRAMBLE The scramble feature makes your transmissions sound garbled to anyone listening without the same scramble code. It does not guarantee confidentiality, but it adds an extra layer of privacy. Scramble mode is by default set to ‘OFF’.
MN002894A01_final.book Page 39 Wednesday, January 4, 2017 5:32 PM The radio display shows the Programming Call Tone’ as follows: The values available for maximum channel settings are dependent on the maximum number of channels the radio supports. PROGRAMMING CALL TONES Call Tones feature allows you to transmit an audible tone to other radios on the same channel to alert them that you are about to talk or to alert them without speaking.
PROGRAMMING FEATURES MN002894A01_final.book Page 40 Wednesday, January 4, 2017 5:32 PM through the programming modes by short pressing the PTT button or (Menu) button until you reach the ‘Microphone Gain Level Programming Mode’.
MN002894A01_final.book Page 41 Wednesday, January 4, 2017 5:32 PM (programmed for scan) to start scanning, as the radio does it automatically. • To stop scanning, short press the SB1 or SB2 button (programmed for scan) again. Scan • Scan allows you to monitor other channels to detect conversations. When the radio detects a transmission, it stops scanning and goes to the active channel. This allows you to listen and talk to people in that channel without having to change channel manually.
PROGRAMMING FEATURES MN002894A01_final.book Page 42 Wednesday, January 4, 2017 5:32 PM The radio display shows the Scan Programming Mode as follows: Weather Channel Programming Mode is the last programming mode available. You can enable or disable the Weather Channel. Both the channel number and current scan setting (YES = Enable or NO = Disable) blinks on the display, indicating you can choose your setting.
MN002894A01_final.book Page 43 Wednesday, January 4, 2017 5:32 PM Note: If the channel alias name is left blank, long pressing the PTT button does not save or leave the alias name. Nuisance Channel Delete Choose the channel number you want to edit by rotating the Channel Selector Knob. Once you have selected the channel number, short press the PTT button or (Menu) button to start editing the channel alias name. The character to be changed starts blinking.
PROGRAMMING FEATURES MN002894A01_final.book Page 44 Wednesday, January 4, 2017 5:32 PM CUSTOMER PROGRAMMING SOFTWARE (CPS) Radio to be programmed USB Ports Drop-In Tray Charger Tray Figure 1: CPS Programming Cable Setting up the radio to the CPS The easiest way to program or change features in your radio is by using the Customer Programming Software (CPS) and the CPS Programming Cable(*). CPS Software is available for free as web based downloadable software at: www.motorolasolutions.
MN002894A01_final.book Page 45 Wednesday, January 4, 2017 5:32 PM channel. The High Power for RDX+ is 5 W for VHF and 4 W for UHF, Low Power for both bands is 2 W. Some frequencies may have FCC transmit power restrictions that disallow them to be set at a higher power level. For more information, refer to the “Frequency and Code Charts” on page 63.
PROGRAMMING FEATURES MN002894A01_final.book Page 46 Wednesday, January 4, 2017 5:32 PM English eight characters of the wave files are used to populate the channel “Name”. Note: • The wave file must be sampled at 8 kHz. • The wave file cannot exceed 65,000 kB in length. Listen to User Customized Voice Prompt (VP) Text This field allows the user to play the output voice signal generated from the Text-to-Speech synthesizer.
MN002894A01_final.book Page 47 Wednesday, January 4, 2017 5:32 PM Weather Alert Mode Choices available are: Frequency Number Value (Mhz) 4 162.4750 5 162.5000 • OFF (Default): Disable the Weather Alert Feature. 6 162.5250 • Tone Alert: Detect the Warning Alarm Tone (WAT). 7 162.5500 • SAME Alert: Detect the Special Area Message Encoding (SAME). THE WEATHER ALERT HAS TWO MODES OF OPERATIONS 1. Value (Mhz) 1 162.4000 2 162.4250 3 162.
MN002894A01_final.book Page 48 Wednesday, January 4, 2017 5:32 PM PROGRAMMING FEATURES unmutes to allow the user to listen the weather English message. For Tone Alert, the radio stays in changes the channel using the Channel Selector Knob. receiving mode until weather signal is weak or New Alert Tone Timer user presses the PTT button or changes the Select a pre-defined time for a radio to play the new alert tone.
MN002894A01_final.book Page 49 Wednesday, January 4, 2017 5:32 PM Note: All Events When checked, the radio allows for all SAME events. No matter how the user programs the event filter, some critical events cannot be blocked. See also: The Critical Events Table. Alert Test Event WATCH When SAME alert is enabled, the radio responds to any test events. When checked, the radio alerts the same way as other SAME alert messages.
PROGRAMMING FEATURES MN002894A01_final.book Page 50 Wednesday, January 4, 2017 5:32 PM STATEMENT EVENT CODE When checked, the radio allows all statement events. Statement is message that contains follow-up information to a warning, watch, or emergency. The Event Code field accepts wild card (“*”). The following are examples of valid Event Code format. Note: EVENT CODE FILTER A specific SAME event can be allowed or blocked. There are maximum of five Event Codes can be programmed.
MN002894A01_final.
PROGRAMMING FEATURES MN002894A01_final.
MN002894A01_final.book Page 53 Wednesday, January 4, 2017 5:32 PM FIPS Cloning with a Multi Unit Charger (MUC) Pocket 1 Pocket 4 Enters/Edits a specific FIPS whenever it is necessary. Further information about FIPS can be found on the Internet at www.nws.noaa.gov/nwr/ indexnw.htm or call the National Weather Service Toll-Free Number SAME county code – 1888-NWS-SAME (1-888-6977263).
PROGRAMMING FEATURES MN002894A01_final.book Page 54 Wednesday, January 4, 2017 5:32 PM When cloning, the MUC does not need to be plugged into a power source, but ALL radios require charged batteries. 1. Turn ON the Target radio and place it into one of tone will be heard within 5 s). 5. Once you have completed the cloning process, turn the radios OFF and ON or, long press the the MUC Target Pockets 2.
MN002894A01_final.book Page 55 Wednesday, January 4, 2017 5:32 PM cables) from the SUCs. 3. Plug one side of the cloning cable mini USB connector to the first SUC and the other end to the second SUC. Note: During the cloning process, no power is being applied to the SUC. The batteries will not be charged. Only data communication is being established between the two radios. 4. Turn ON the Target Radio and place it into one 5. For the Source Radio, power ON the radio with of the SUCs.
PROGRAMMING FEATURES MN002894A01_final.book Page 56 Wednesday, January 4, 2017 5:32 PM ‘chirp’ whereas the ‘fail’ tone sounds similar to a 6. Ensure that the Source radio is in cloning mode. ‘bonk’ tone. If the Source radio is a display 7. Ensure that the two radios are both from the model, it will either show ‘Pass’ or ‘Fail’ on the 8. Once you have completed the cloning process, turn the radios OFF and ON to exit ‘clone’ mode.
MN002894A01_final.book Page 57 Wednesday, January 4, 2017 5:32 PM When cloning using this method, you need the CPS software, a Drop-In Tray Charger and the CPS Programming Cable. PROGRAMMING FEATURES Cloning using the Customer Programming Software (CPS) Radio to be programmed To order the CPS Programming Cable, please refer to part number RKN4155_.
MN002894A01_final.book Page 58 Wednesday, January 4, 2017 5:32 PM TROUBLESHOOTING TROUBLESHOOTING Symptom No Power Extreme operating temperatures may affect battery life. Refer to “About the Li-Ion Battery” on page 15. Confirm Interference Eliminator Code is set. Hearing other noises or conversation on a channel Frequency or Interference Eliminator Code may be in use. Change settings: either change frequencies or codes on all radios. Make sure radio is at the right frequency and code when transmitting.
MN002894A01_final.book Page 59 Wednesday, January 4, 2017 5:32 PM Symptom Try This... Steel and/or concrete structures, heavy foliage, buildings or vehicles decrease range. Check for clear line of sight to improve transmission. Limited talk range Change location of radio. To increase range and coverage, you can reduce obstructions or increase power. UHF radios provides greater coverage in industrial and commercial buildings.
MN002894A01_final.book Page 60 Wednesday, January 4, 2017 5:32 PM Symptom Try This... TROUBLESHOOTING Radios are too close; they must be at least five feet apart. Heavy static or interference Refer to “Talking and Monitoring” on page 29. Recharge or replace Li-Ion battery. Low batteries Extreme operating temperatures affect battery life. Refer to “About the Li-Ion Battery” on page 15.
MN002894A01_final.book Page 61 Wednesday, January 4, 2017 5:32 PM Symptom Try This... VOX feature might be set to OFF. Use the CPS to ensure that the VOX Sensitivity level is not set to ‘0’. Accessory not working or not compatible. Refer to “Hands-Free Use/VOX” on page 32. Check drop-in tray charger is properly connected and correspond to a Battery does not charge compatible power supply.
MN002894A01_final.book Page 62 Wednesday, January 4, 2017 5:32 PM USE AND CARE USE AND CARE Use a soft damp cloth to clean the exterior Do not use alcohol or cleaning solutions If the radio is submerged in water...
MN002894A01_final.book Page 63 Wednesday, January 4, 2017 5:32 PM RDX UHF FREQUENCIES CHART The charts in this section provide Frequency and Code information. These charts are useful when using the Motorola Solutions RDX Series two-way radios with other business radios. RDU4163 – UHF DEFAULT FREQUENCIES CHART RDX UHF 16CH Radios Default Frequencies – RDU4163 Channel Frequency # Frequency (MHz) Code# Code Bandwidth 1 1 458.6625 1 67.0 Hz 12.5 kHz 2 2 469.2625 1 67.0 Hz 12.
MN002894A01_final.book Page 64 Wednesday, January 4, 2017 5:32 PM FREQUENCY AND CODE CHARTS RDX UHF 16CH Radios Default Frequencies – RDU4163 English 64 11 1 458.6625 6 82.5 Hz 12.5 kHz 12 2 469.2625 6 82.5 Hz 12.5 kHz 13 1 458.6625 7 85.4 Hz 12.5 kHz 14 2 469.2625 7 85.4 Hz 12.5 kHz 15 1 458.6625 8 88.5 Hz 12.5 kHz 16 2 469.2625 8 88.5 Hz 12.
MN002894A01_final.book Page 65 Wednesday, January 4, 2017 5:32 PM RDX UHF FREQUENCIES CHART RDX UHF Frequencies Frequency # Frequency (MHz) Bandwidth 1 464.5000 12.5 kHz 15 461.1875 12.5 kHz 2 464.5500 12.5 kHz 16 461.2125 12.5 kHz *3 467.7625 12.5 kHz 17 461.2375 12.5 kHz *4 467.8125 12.5 kHz 18 461.2625 12.5 kHz *5 467.8500 12.5 kHz 19 461.2875 12.5 kHz *6 467.8750 12.5 kHz 20 461.3125 12.5 kHz *7 467.9000 12.5 kHz 21 461.3375 12.5 kHz *8 467.9250 12.
MN002894A01_final.book Page 66 Wednesday, January 4, 2017 5:32 PM FREQUENCY AND CODE CHARTS RDX UHF Frequencies (Continued) English Frequency # Frequency (MHz) Bandwidth Frequency # Frequency (MHz) Bandwidth *29 462.9125 12.5 kHz 47 466.3625 12.5 kHz 30 464.4875 12.5 kHz *48 467.7875 12.5 kHz 31 464.5125 12.5 kHz *49 467.8375 12.5 kHz 32 464.5375 12.5 kHz *50 467.8625 12.5 kHz 33 464.5625 12.5 kHz *51 467.8875 12.5 kHz 34 466.0375 12.5 kHz *52 467.9125 12.
MN002894A01_final.book Page 67 Wednesday, January 4, 2017 5:32 PM RDX UHF Frequencies (Continued) Frequency # Frequency (MHz) Bandwidth 65 451.1875 12.5 kHz 82 456.4375 12.5 kHz 66 451.2375 12.5 kHz 83 456.5375 12.5 kHz 67 451.2875 12.5 kHz 84 456.6375 12.5 kHz 68 451.3375 12.5 kHz 85 457.3125 12.5 kHz 69 451.4375 12.5 kHz 86 457.4125 12.5 kHz 70 451.5375 12.5 kHz 87 457.5125 12.5 kHz 71 451.6375 12.5 kHz 88 457.7625 12.5 kHz 72 452.3125 12.5 kHz 89 457.
FREQUENCY AND CODE CHARTS MN002894A01_final.book Page 68 Wednesday, January 4, 2017 5:32 PM English RDU4160 – UHF DEFAULT FREQUENCIES CHART RDX UHF 16CH Radios Default Frequencies – RDU4160 Channel Frequency # Frequency (MHz) Code # Code Bandwidth 1 1 464.5000 1 67.0 Hz 12.5 kHz 2 1 464.5000 4 77.0 Hz 12.5 kHz 3 1 464.5000 8 88.5 Hz 12.5 kHz 4 1 464.5000 29 179.9 Hz 12.5 kHz 5 1 464.5000 0 - 12.5 kHz 6 2 464.5500 1 67.0 Hz 12.5 kHz 7 2 464.5500 6 82.5 Hz 12.
MN002894A01_final.book Page 69 Wednesday, January 4, 2017 5:32 PM RDX UHF 16CH Radios Default Frequencies – RDU4160 34 462.0375 9 91.5 Hz 12.5 kHz 15 36 464.0875 11 97.4 Hz 12.5 kHz 16 38 464.1375 13 103.5 Hz 12.5 kHz WC = Weather Channel Frequency PROGRAMMING CUSTOMIZED FREQUENCIES ON RDU4160 4 W Models can be programmed to have customized frequencies (different from the ones shown in the UHF charts in previous pages). UHF range is 438 – 470 MHz.
MN002894A01_final.book Page 70 Wednesday, January 4, 2017 5:32 PM CTCSS AND PL/DPL CODES FREQUENCY AND CODE CHARTS CTCSS Codes CTCSS Hz CTCSS Hz CTCSS Hz 1 67.0 14 107.2 27 167.9 2 71.9 15 110.9 28 173.8 3 74.4 16 114.8 29 179.9 Note: English 70 4 77.0 17 118.8 30 186.2 5 79.7 18 123 31 192.8 6 82.5 19 127.3 32 203.5 7 85.4 20 131.8 33 210.7 8 88.5 21 136.5 34 218.1 9 91.5 22 141.3 35 225.7 10 94.8 23 146.2 36 233.6 11 97.4 24 151.
MN002894A01_final.
MN002894A01_final.
MN002894A01_final.
MN002894A01_final.
MN002894A01_final.book Page 75 Wednesday, January 4, 2017 5:32 PM ACCESSORIES ANTENNA Part No. Description UHF Whip Antenna 438–470 MHz RAN4033 UHF Stubby Antenna 438–470 MHz AUDIO ACCESSORIES Part No. Description HKLN4599 Earpiece w/Inline Mic Swivel HKLN4604 Earpiece BR BATTERY Part No. Description RLN6308 High Capacity Li-Ion Battery RLN6351 Standard Li-ion Battery Description ACCESSORIES RAN4031 Part No.
MN002894A01_final.book Page 76 Wednesday, January 4, 2017 5:32 PM CHARGERS SOFTWARE APPLICATIONS ACCESSORIES Part No. English Description RLN6304 Rapid ACCY Charging Kit Americas (*) RLN6309 Multi Unit Charger (MUC) Kit North America RLN6175 Standard Drop-in Tray Charger Description RLN6302 Leather Carry Case RLN6307 Spring Action Belt Clip 76 RVN5147 Description Customer Programming Software (CPS) POWER SUPPLIES AC PIN ADAPTERS Part No. RLN6349 CARRY ACCESSORIES Part No. Part No.
MN002894A01_final.book Page 77 Wednesday, January 4, 2017 5:32 PM What Does this Warranty Cover? Subject to the exclusions contained below, Motorola Solutions, Inc.
MN002894A01_final.book Page 78 Wednesday, January 4, 2017 5:32 PM MOTOROLA SOLUTIONS LIMITED WARRANTY FOR THE UNITED STATES AND CANADA Exclusions English Normal Wear and Tear. Periodic maintenance, repair and replacement of parts due to normal wear and tear are excluded from coverage. Batteries. Only batteries whose fully charged capacity falls below 80% of their rated capacity and batteries that leak are covered by this limited warranty. Abuse & Misuse.
MN002894A01_final.book Page 79 Wednesday, January 4, 2017 5:32 PM WHO IS COVERED? This warranty extends only to the first consumer purchaser, and is not transferable. HOW TO OBTAIN WARRANTY SERVICE OR OTHER INFORMATION? Contact your Motorola point of purchase. SOFTWARE COPYRIGHT NOTICE The Motorola Solutions products described in this manual may include copyrighted Motorola Solutions and third party software stored in semiconductor memories or other media.
