BRUS_display.
BRUS_display.
BRUS_display.book Page 1 Monday, January 16, 2012 5:28 PM CONTENTS Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Batteries and Chargers Safety Information. . . . . . . . . . . . . . . . . . . . 6 Operational Safety Guidelines. . . . . . . . . . . . .7 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 8 Package Contents . . . . . . . . . . . . . . . . . . . . . .8 FCC Licensing Information . . . . . . . . . . . 10 Interference Information . . . . . . . . . . . . . . . .
CONTENTS BRUS_display.book Page 2 Monday, January 16, 2012 5:28 PM English Getting Started . . . . . . . . . . . . . . . . . . . . . .32 Programming Features . . . . . . . . . . . . . . . 42 Turning radio ON/OFF. . . . . . . . . . . . . . . . . .32 Adjusting volume . . . . . . . . . . . . . . . . . . . . . .32 Reading the Display . . . . . . . . . . . . . . . . . . .32 Selecting a Channel . . . . . . . . . . . . . . . . . . .33 Talking and Monitoring . . . . . . . . . . . . . . . . .
BRUS_display.book Page 3 Monday, January 16, 2012 5:28 PM Troubleshooting . . . . . . . . . . . . . . . . . . . . .61 Use and Care . . . . . . . . . . . . . . . . . . . . . . . .65 Frequency and Code Charts . . . . . . . . . . .66 RDX VHF Frequencies Chart . . . . . . . . . . . .66 RDV2080d - VHF Default Frequencies Chart. . . . . . . . . . . . . . . . . . . . .68 RDX UHF Frequencies Chart . . . . . . . . . . . .69 RDU2080d - UHF Default Frequencies Chart . . . . . . . . . . . . . . . . . . . .
BRUS_display.book Page 4 Monday, January 16, 2012 5:28 PM Power Supplies . . . . . . . . . . . . . . . . . . . . . . .87 CONTENTS RDX Series™ Features Summary . . . . . . .88 English Programmable Buttons Chart . . . . . . . . . .98 Icons Chart. . . . . . . . . . . . . . . . . . . . . . . . . .
BRUS_display.book Page 5 Monday, January 16, 2012 5:28 PM SAFETY PRODUCT SAFETY AND RF EXPOSURE COMPLIANCE ! Caution For a list of Motorola-approved antennas, batteries, and other accessories, visit the following website which lists approved accessories: www.motorolasolutions.com/RDX SAFETY Before using this product, read the operating instructions and RF energy awareness information contained in the Product Safety and RF Exposure booklet enclosed with your radio.
BRUS_display.book Page 6 Monday, January 16, 2012 5:28 PM BATTERIES AND CHARGERS SAFETY INFORMATION 3. and cord, pull by the plug rather than the cord when disconnecting the charger. 4. extension cord could result in risk of fire and electric shock.
BRUS_display.book Page 7 Monday, January 16, 2012 5:28 PM OPERATIONAL SAFETY GUIDELINES • Turn the radio OFF when charging battery. • The charger is not suitable for outdoor use. Use only in dry locations/conditions. • Connect charger only to an appropriately fused • The outlet to which this equipment is connected should be nearby and easily accessible. • Maximum ambient temperature around the power supply equipment must not exceed 40°C (104°F).
BRUS_display.book Page 8 Monday, January 16, 2012 5:28 PM INTRODUCTION INTRODUCTION Thank you for purchasing the Motorola RDX Series™ Radio. This radio is a product of Motorola's 75 plus years of experience as a world leader in the designing and manufacturing of communications equipment. The RDX Series™ radios provide cost-effective communications for businesses such as retail stores, restaurants, schools, construction sites, manufacturing, property and hotel management and more.
BRUS_display.book Page 9 Monday, January 16, 2012 5:28 PM For a copy of a large-print version of this user guide or for product-related questions, contact: For product information visit us at: www.motorolasolutions.
BRUS_display.book Page 10 Monday, January 16, 2012 5:28 PM (FCC). To transmit on these frequencies, you FCC LICENSING INFORMATION are required to have a license issued by the FCC. Application is made available on FCC INTERFERENCE INFORMATION FCC LICENSING INFORMATION This device complies with Part 15 of the FCC Form 159. Rules.
BRUS_display.book Page 11 Monday, January 16, 2012 5:28 PM Before filling out your application, you must Replacement of any transmitter component decide which frequency(ies) you can operate (crystal, semiconductor, etc.) not authorized by on. See “Frequencies and Code Charts”. For the FCC equipment authorization for this radio questions on determining the radio frequency, could violate FCC rules.
BRUS_display.
BRUS_display.book Page 13 Monday, January 16, 2012 5:28 PM On/Off/Volume Knob Front Buttons Used to turn the radio ON or OFF and to adjust the radio’s volume. Accessory Connector Used to connect compatible audio accessories. Model Label Indicates the model of the radio. Microphone Speaks clearly into the microphone when sending a message. Antenna LED Indicator Used to give battery status, power-up status, radio call information and scan status.
BRUS_display.book Page 14 Monday, January 16, 2012 5:28 PM • A Programmable Button Configured as Preset Channel 1. • Programmable Button B Configured as Preset Channel 2. • Programmable Button C Configured as Tx Power Selection. RADIO OVERVIEW Note: English A short press of either preset button (A or B) tunes the radio to the preset channel and the radio will play a good chirp. You can assign different functions to these buttons via the CPS.
BRUS_display.book Page 15 Monday, January 16, 2012 5:28 PM This User Guide covers multiple RDX Series™ models, and may detail some features your radio does not have.
BRUS_display.book Page 16 Monday, January 16, 2012 5:28 PM BATTERY FEATURES RDX Series™ radios provide Lithium-Ion batteries that come in different capacities that will define the battery life. It also offers the option to use Alkaline batteries. About the Li-Ion Battery RADIO OVERVIEW The RDX Series™ radio comes equipped with a rechargeable Li-Ion battery. This battery should be charged before initial use to ensure optimum capacity and performance.
BRUS_display.book Page 17 Monday, January 16, 2012 5:28 PM Battery Recycling and Disposal Many retailers and dealers participate in this program. For the location of the drop-off facility closest to you, access RBRC's Internet web site at: www.rbrc.com or call: 1-800-8-BATTERY This internet site and telephone number also provides other useful information concerning recycling options for consumers, businesses and governmental agencies. RADIO OVERVIEW Li-Ion rechargeable batteries can be recycled.
BRUS_display.book Page 18 Monday, January 16, 2012 5:28 PM Installing the Lithium-Ion (Li-Ion) Battery Removing the Lithium-Ion (Li-Ion) Battery Battery Latch Battery Latch RADIO OVERVIEW slots English 1. Turn OFF the radio. 1. Turn OFF the radio. 2. With the Motorola logo side up on the battery 2. Push down the battery latch and hold it pack, fit the tabs at the bottom of the battery into the slots at the bottom of the radio’s body. 3.
BRUS_display.book Page 19 Monday, January 16, 2012 5:28 PM Alkaline Battery Pack (Optional Accessory) Removing Alkaline Batteries Installing Alkaline Batteries Alkaline Battery Door Turn OFF the radio, if it is turned ON. 2. Remove Li-Ion battery. 3. Assemble alkaline battery pack in the same steps as installing the Li-Ion battery pack. 4. Remove battery door from alkaline battery pack. 5. Slide the 5 AA alkaline batteries into the frame, 1. Turn OFF the radio, if it is turned ON. 2.
BRUS_display.book Page 20 Monday, January 16, 2012 5:28 PM Attaching and Removing Antenna RADIO OVERVIEW These instructions apply ONLY for RDU4160d radio. Do not attempt to remove the antenna if your radio is not one of these models. English Attaching the Antenna Removing the Antenna 1. 1. Align the threaded end of the antenna with the radio’s antenna connector. 2. Turn the antenna clockwise to fasten it. 20 Turn the antenna counterclockwise until you can remove it.
BRUS_display.book Page 21 Monday, January 16, 2012 5:28 PM Installing Spring Action Belt Clip Power Supply, Adaptor and Drop-in Tray Charger Belt Clip Tab Power Supply Spring Action Belt Clip 1. Slide the spring action belt clip rails into the belt Drop-in Tray Charger The radio is equipped with one Drop-in Tray Charger and one Power Supply with Adaptor. For details, see “Chargers” on page 86.
BRUS_display.book Page 22 Monday, January 16, 2012 5:28 PM Battery Life Information When the Battery Save feature is ON (enabled by default) the battery life will be longer. The following chart summarizes battery life estimations: Li-Ion Battery Life with Battery Save feature ON RADIO OVERVIEW Battery Type English 4 Watts 2 Watts Standard 8.5 hours 8.5 hours 12 hours High 17 hours 17 hours 24 hours Ultra High 18.5 hours 18.
BRUS_display.book Page 23 Monday, January 16, 2012 5:28 PM Alkaline Battery Life The following chart estimates the Alkaline battery life: Alkaline Battery Life Battery Save Feature ON 5 Watts 26 hours* 4 Watts 26 hours* 2 Watts 26 hours Notes: • Battery life are being estimated based on 5% transmit/ 5% receive/ 90% standby standard duty cycle. * When using Alkaline battery, the radio is set to 2W by default.
BRUS_display.book Page 24 Monday, January 16, 2012 5:28 PM Battery Meter The battery meter located in the upper left corner of the display indicates how much battery power you have remaining.
BRUS_display.book Page 25 Monday, January 16, 2012 5:28 PM Charging the Battery RDX Series™ offers two types of chargers : • Standard Charger and, • Rapid Charger. Charging with the Drop-in Tray Single Unit Charger (SUC) The radio comes equipped with a Standard Charger. Power Supply (Transformer) To charge the battery (with the radio attached), place it in a Motorola-approved Drop-in Tray Single Unit Charger or Drop-in Tray Multi Unit Charger. Note: 1.
BRUS_display.book Page 26 Monday, January 16, 2012 5:28 PM Charging a Standalone Battery Charging a Standard Battery RADIO OVERVIEW The drop-in tray charger has a removable bracket that is adjustable depending on the type of battery that needs to be charged. It is designed to charge either the battery (with the radio) or a standalone battery. The drop-in tray charger's default position will charge a standard battery.
BRUS_display.book Page 27 Monday, January 16, 2012 5:28 PM Charging a High Capacity or Ultra High Capacity Battery 3. Repeat same procedure to return to the charging a Standard Battery position. Label on the removable bracket should show ‘Standard Removable Piece Removable Piece Battery’ facing front. Turn around horizontal 180 degree Note: Make sure the bracket is assembled correctly for both standalone battery and battery (with radio).
BRUS_display.
BRUS_display.
BRUS_display.book Page 30 Monday, January 16, 2012 5:28 PM Estimated Charging Time The following table provides the estimated charging time of the battery. For further details, see “Battery” on page 85. Estimated Charging Time Battery Type RADIO OVERVIEW Charging Solution English 30 Standard High Capacity Ultra High Capacity Standard Charging Solution 7 hours 12 hours 13 hours Rapid Charging Solution 1.5 hours 3 hours 3.
BRUS_display.book Page 31 Monday, January 16, 2012 5:28 PM Charging a Radio and Battery using a Multi Unit Charger- MUC (Optional Accessory) Notes: • This Multi Unit Charger also allows you to clone up to 3 radios (3 Source radios and 3 Target radios). Refer to page 55 for details. • Further details on MUC’s operation are explained in the Instructions Sheet provided with the MUC. For part number details, refer to the Accessories section. 1. Place the charger on a flat surface. 2.
GETTING STARTED BRUS_display.book Page 32 Monday, January 16, 2012 5:28 PM GETTING STARTED READING THE DISPLAY Keypad Lock For the following explanations refer to "Parts of the radio" on page page 12. Vox / iVox Scan Signal Strength TURNING RADIO ON/OFF Battery Level Turn the On/Off/Volume knob clockwise to turn ON the radio. The radio will chirp and the LED will briefly blink a red light.
BRUS_display.book Page 33 Monday, January 16, 2012 5:28 PM SELECTING A CHANNEL Program each channel separately. Each channel has its own Frequency, Interference Eliminator Code and Scan Settings. Note: (*) This assumes SB1 is not being programmed for a different mode. RECEIVING A CALL 1. For monitoring press and hold the SB1(*) button to access channel traffic. If no activity is present, you will hear ‘static’. Press again SB1 to release.
GETTING STARTED BRUS_display.book Page 34 Monday, January 16, 2012 5:28 PM Signal Strength Indicator and Channel Busy Indicators TALK RANGE TALK RANGE When there is activity on a frequency the radio displays the strength indicator icon while radio LED blinks faster. When there is activity on the same frequency and code as your radio (your radio is receiving), the radio signal strength icon can change from 1 (weakest) to 6 (strongest) depending on the radio reception coverage.
BRUS_display.book Page 35 Monday, January 16, 2012 5:28 PM 2. Frequency: The frequency your radio uses to 3. GETTING STARTED transmit/receive. Interference Eliminator Code: These codes help minimize interference by providing you with a choice of code combinations. 4. Scramble Code: Codes that make your transmissions sound garbled to anyone listening who is not set to that specific code.
BRUS_display.
BRUS_display.book Page 37 Monday, January 16, 2012 5:28 PM HANDS-FREE USE/VOX Open accessory cover. 3. Insert audio accessory’s plug firmly into 4. Turn the radio ON. Radio will beep and LED will accessory port. blink double red. The display will show the VOX 5. VOX Accessory Accessory Connector icon. Lower radio volume BEFORE placing accessory near ear. 6. To transmit, speak into accessory microphone GETTING STARTED 2. and to receive, stop talking. 7.
GETTING STARTED BRUS_display.book Page 38 Monday, January 16, 2012 5:28 PM Hands Free without Accessories (iVOX) Battery Save • Battery Save feature extends battery life as your radio goes into ‘Idle’ state each time there is no radio activity. To enable/disable press SB1 and SB2 buttons simultaneously for 2 or 3 seconds while powering up the radio until you hear a quick series of beeps.
BRUS_display.book Page 39 Monday, January 16, 2012 5:28 PM End of Transmission Tone (Roger Beep Tone) GETTING STARTED Button A (if Call Tone feature has been assigned). Short press the SB1 button while turning ON the radio to enable/disable End of Transmission Tone. Note: This setting is set to OFF by default Keypad Beeps Keypad Beeps can be enabled/disabled by short pressing SB2 button (until radio ‘chirps’) while turning ON the radio.
BRUS_display.book Page 40 Monday, January 16, 2012 5:28 PM GETTING STARTED Setting VOX / iVOX sensitivity The VOX/iVOX sensitivity can be adjusted via the MENU as well as the CPS. To modify via the MENU, first make sure you have enabled either VOX or iVOX (See “Hands-Free Use/ VOX” on page 37.). Once VOX/iVOX has been enabled, short press MENU.
BRUS_display.book Page 41 Monday, January 16, 2012 5:28 PM Battery Type Menu GETTING STARTED Only if the battery pack is not detected, the radio will allow changes to the battery type setting from either Lithium-Ion or Alkaline.To change the setting, press the MENU button as many times as needed until the radio blinks the current battery type (either ‘LITHIUM’ or ‘ALKALINE’). A full battery icon will be shown as follows: Use the / buttons to choose either ‘LITHIUM’ or ‘ALKALINE’.
BRUS_display.book Page 42 Monday, January 16, 2012 5:28 PM PROGRAMMING FEATURES You can scroll up/down to select the different channels by pressing the / buttons. PROGRAMMING FEATURES ENTERING PROGRAMMING MODE To enter ‘Programming Mode’, press and hold both the PTT button and the SB1 button simultaneously for three seconds, while turning ON the radio. A unique tone will sound, indicating that the radio has entered ’Programming Mode’ and the radio LED will signal a green heartbeat.
BRUS_display.book Page 43 Monday, January 16, 2012 5:28 PM • • Whenever the radio wrap around to the beginning of the Programming Mode options the changes will be automatically saved, even if you turn OFF the radio. You can exit any Programming Mode without saving changes (as long as the radio has not return to the beginning) by turning the radio OFF.
BRUS_display.book Page 44 Monday, January 16, 2012 5:28 PM PROGRAMMING RX (RECEPTION) CODES (CTCSS/DPL) PROGRAMMING FEATURES Once you have chosen the channel you want to program, short press the PTT button or MENU to scroll through the options until you reach the ‘Code Programming Mode’. The radio display will show the blinking CTCSS/DPL code as follows: RX PROGRAMMING SCRAMBLE The scramble feature makes your transmissions sound garbled to anyone listening without the same scramble code.
BRUS_display.book Page 45 Monday, January 16, 2012 5:28 PM PTT button to move to the next programming feature without saving. Note: The values available for scrambling are dependent upon the values programmed via the CPS. When the scramble setting is ‘0’ it means it is disabled. PROGRAMMING MAXIMUM NUMBER OF CHANNELS To program the maximum number of channels use the / buttons until you locate the desired setting. Long press the PTT button to save and exit.
BRUS_display.book Page 46 Monday, January 16, 2012 5:28 PM PROGRAMMING CALL TONES PROGRAMMING FEATURES Call Tones will enable you to transmit to other radios in your group in such way that you can alert them that you are about to talk or alert them without speaking. In ‘Call Tone Selection Mode’, you can configure the call tone type for the radio. The settings available will depend on the maximum number of call tones your radio supports.
BRUS_display.book Page 47 Monday, January 16, 2012 5:28 PM PROGRAMMING MICROPHONE GAIN LEVEL To configure the microphone gain level, enter ’Programming Mode’ and scroll through the programming options by short pressing the PTT button. When you reach the ‘Microphone Gain Level Programming Mode’ the display will read as follows: The current microphone gain level setting will blink. You can select the desired microphone gain level by pressing the / buttons (1=low gain,2= Medium gain or 3= high gain).
BRUS_display.book Page 48 Monday, January 16, 2012 5:28 PM exit and save or short press the PTT button to move to the next programming feature without saving. Note: PROGRAMMING FEATURES To start scanning, press the SB2 button (*). When the radio detects channel activity, it will stop on that channel until activity on the channel ends. You can talk to the person(s) transmitting without having to switch channels by pressing PTT. • To stop scanning, short press the SB2 button again.
BRUS_display.book Page 49 Monday, January 16, 2012 5:28 PM for a particular channel, do not press SB2 button to start scanning, as the radio will do it automatically. Programming Scan List Once you have selected the channel, proceed to enable (‘YES’) or disable (‘NO’) the scan feature by toggling the SB2 (*) button. Once you have set the values you need, long press the PTT button to save an exit. Notes: • (*)This assumes the SB2 button is not being programmed for a different mode.
BRUS_display.book Page 50 Monday, January 16, 2012 5:28 PM PROGRAMMING BUTTONS PROGRAMMING FEATURES You can map any channel to either button B or C as a preset channel. To enable, enter ’Programming Mode’ and choose the channel you want to set as preset channel using the / buttons. Once you have selected your channel, press and hold the B or C button for 2 – 3 seconds. A short press of either preset button (B and C) will play a good key chirp.
BRUS_display.book Page 51 Monday, January 16, 2012 5:28 PM button B and the cursor is positioned in a valid character, the button B will delete the current character and replace it with a blank space. • Use the / buttons to change the current selected character to the next ASCII value in alphabetical order (from A to Z). The characters will be uppercase letters. To toggle character between uppercase and lower case, press the A button.
BRUS_display.book Page 52 Monday, January 16, 2012 5:28 PM NUISANCE CHANNEL DELETE PROGRAMMING FEATURES Nuisance Channel Delete allows you to temporarily remove channels from the ‘Scan List’. This feature is useful when irrelevant conversations on a ‘nuisance’ channel tie up your radio's scanning features.
BRUS_display.book Page 53 Monday, January 16, 2012 5:28 PM Notes: • (*) CPS Programming Cable (P/N RKN4155) is an accessory sold separately. Please contact your Motorola Point of Purchase for more information. Bandwidth Select Default setting for Bandwidth Select depends on the specific frequency and channel. For details refer to ‘Frequencies and Codes Charts’ Section.Some frequencies have selectable channel spacing, which must match other radios for optimum audio quality.
BRUS_display.book Page 54 Monday, January 16, 2012 5:28 PM Note: Some frequencies may have FCC transmit power restrictions that don't allow them to be set at a higher power level. For details see the Frequencies and Code Chart Section. PROGRAMMING FEATURES Battery Type Setting The RDX™ series radio can be powered by either Alkaline, Lithium-Ion cells or battery pack. The battery pack can be detected at power-up and the corresponding battery level will be shown on the radio's display.
BRUS_display.book Page 55 Monday, January 16, 2012 5:28 PM Cloning with a Multi-Unit Charger (MUC) 1. Turn ON the Target radio and place it into one of the MUC Target Pockets 2. Power the Source radio following the sequence below: • a Source radio (radio which profiles will be cloned or copied from) and • a Target radio (the radio which profile will be cloned from the source radio). Long press the PTT button and SB2 simultaneously while turning the radio ON.
BRUS_display.book Page 56 Monday, January 16, 2012 5:28 PM 5. Once you have completed the cloning process, turn the radios OFF and ON to exit the ‘cloning’ Cloning Radios using the Radio to Radio (R2R) Cloning Cable (optional accessory) mode. Note: If cloning fails please refer to “What to do if cloning fails” on page 57. PROGRAMMING FEATURES Further details on how to clone units are explained in the instructions sheet provided with the MUC. When ordering the MUC please refer to P/N RLN6309.
BRUS_display.book Page 57 Monday, January 16, 2012 5:28 PM • Both radios are turned OFF. • Both radios are of the same radio model. 2. Unplug any cables (power supply or USB 6. release Side Button 1 (SB1). 7. successful) or a “fail” tone (cloning process has Plug one side of the cloning cable mini failed). The pass tone sounds like a good key connector to one SUC. Plug the other end to “chirp” whereas the “fail” tone sounds similar to the second SUC.
BRUS_display.book Page 58 Monday, January 16, 2012 5:28 PM 1. Make sure that the radio batteries on both radios are fully charged. 2. Make sure that there is no debris in the To clone RDX™ radios using the CPS software, you will need to have available the CPS, a Drop-in Charger Tray and the CPS Programming Cable. Information on how to clone using the CPS is available either in charging tray or on the radio contacts.
BRUS_display.book Page 59 Monday, January 16, 2012 5:28 PM Bandwidth will be available. If the repeater feature is mapped (using CPS) to one of the radio buttons, then the repeater icon will blink. This indicates that you can use the repeater ‘button’ to toggle ON/OFF repeater. If repeater is not enabled in the radio this icon will not be displayed. TX To program the desired frequency, scroll using the / buttons until you get the desired frequency code value.
BRUS_display.book Page 60 Monday, January 16, 2012 5:28 PM To program the CTCSS/DPL code, scroll through the programming options by short pressing the PTT button until your radio display shows: To program the Bandwidth TX scroll down/up with the / buttons until you get the following screen: TX BW PROGRAMMING FEATURES TX English To program the desired code, scroll using / buttons until you get the desired CTCSS/ DPL code value.
BRUS_display.book Page 61 Monday, January 16, 2012 5:28 PM TROUBLESHOOTING Symptom Try This... Recharge or replace the Li-Ion battery. No Power Reposition or replace AA batteries. Extreme operating temperatures may affect battery life. Refer to See “About the Li-Ion Battery” on page 16. Confirm Interference Eliminator Code is set. Hearing other noises or conversation on a channel Frequency or Interference Eliminator Code may be in use. Change settings: either change frequencies or codes on all radios.
BRUS_display.book Page 62 Monday, January 16, 2012 5:28 PM Symptom Try This... Steel and/or concrete structures, heavy foliage, buildings or vehicles decrease range. Check for clear line of sight to improve transmission. Wearing radio close to body such as in a pocket or on a belt decreases range. Change location of radio. To increase range and coverage, you can either Limited talk range reduce obstructions, increase power, or use UHF radio instead of VHF radio.
BRUS_display.book Page 63 Monday, January 16, 2012 5:28 PM Symptom Try This... Radios are too close; they must be at least five feet apart. Heavy static or interference Radios are too far apart or obstacles are interfering with transmission. Refer to “Talking and Monitoring” on page 33. Recharge or replace Li-Ion battery. Replace AA batteries. Low batteries Extreme operating temperatures affect battery life. Refer to “About the Li-Ion Battery” on page 16.
BRUS_display.book Page 64 Monday, January 16, 2012 5:28 PM Symptom Try This... VOX feature might be set to OFF. Cannot activate VOX Use the CPS to ensure that the VOX Sensitivity level is not set to ‘0’. Accessory not working or not compatible. Refer to “Hands-Free Use/VOX” section on page 37. Check drop-in tray charger is properly connected and correspond to a compatible power supply.
BRUS_display.book Page 65 Monday, January 16, 2012 5:28 PM USE AND CARE USE AND CARE Use a soft damp cloth to clean the exterior Do not immerse in water Do not use alcohol or cleaning solutions If the radio is submerged in water...
BRUS_display.book Page 66 Monday, January 16, 2012 5:28 PM FREQUENCY AND CODE CHARTS RDX VHF FREQUENCIES CHART FREQUENCY AND CODE The charts in this section provide Frequency and Code information. These charts are useful when using Motorola RDX Series™ two-way radios with other business radios. Most of the frequency’s positions are the same as Spirit M, GT, S, and XTN Series Frequencies.
BRUS_display.book Page 67 Monday, January 16, 2012 5:28 PM RDX VHF Frequencies (continued) Frequency # Frequency Bandwidth (MHz) Frequency # Frequency (MHz) Bandwidth 23 154.5400 12.5 kHz 26 158.4000 12.5 kHz 24 153.0050 12.5 kHz 27 158.4075 12.5 kHz 25 154.5475 12.5 kHz Legacy Series radios. This means that if you select the RDX radio in one of these frequencies the radio will not inter-operate with an XTN radio.
BRUS_display.book Page 68 Monday, January 16, 2012 5:28 PM RDV2080d – VHF DEFAULT FREQUENCIES CHART FREQUENCY AND CODE RDX VHF 8CH Radios Default Frequencies – RDV2080d English 68 Channel Frequency # Frequency (MHz) Code # Code Bandwidth 1 20 154.4900 1 67.0 Hz 12.5 kHz 2 21 154.5150 1 67.0 Hz 12.5 kHz 12.5 kHz 3 1 151.6250 1 67.0 Hz 4 2 151.9550 1 67.0 Hz 12.5 kHz 5 10 151.5125 1 67.0 Hz 12.5 kHz 6 12 151.6850 1 67.0 Hz 12.5 kHz 7 15 151.7750 1 67.
BRUS_display.book Page 69 Monday, January 16, 2012 5:28 PM RDX UHF FREQUENCIES CHART RDX UHF Frequencies Frequency (MHz) Bandwidth Frequency # Frequency (MHz) Bandwidth 1 464.5000 12.5 kHz 14 461.1625 12.5 kHz 2 464.5500 12.5 kHz 15 461.1875 12.5 kHz *3 467.7625 12.5 kHz 16 461.2125 12.5 kHz *4 467.8125 12.5 kHz 17 461.2375 12.5 kHz *5 467.8500 12.5 kHz 18 461.2625 12.5 kHz *6 467.8750 12.5 kHz 19 461.2875 12.5 kHz *7 467.9000 12.5 kHz 20 461.3125 12.
BRUS_display.book Page 70 Monday, January 16, 2012 5:28 PM FREQUENCY AND CODE RDX UHF Frequencies (Continued) English Frequency # Frequency (MHz) Bandwidth Frequency # Frequency (MHz) Bandwidth *27 462.8625 12.5 kHz 38 466.1375 12.5 kHz *28 462.8875 12.5 kHz 39 466.1625 12.5 kHz *29 462.9125 12.5 kHz 40 466.1875 12.5 kHz 30 464.4875 12.5 kHz 41 466.2125 12.5 kHz 31 464.5125 12.5 kHz 42 466.2375 12.5 kHz 32 464.5375 12.5 kHz 43 466.2625 12.5 kHz 33 464.5625 12.
BRUS_display.book Page 71 Monday, January 16, 2012 5:28 PM RDX UHF Frequencies (Continued) Bandwidth Frequency # Frequency (MHz) Bandwidth *49 467.8375 12.5 kHz 61 467.1875 12.5 kHz *50 467.8625 12.5 kHz 62 467.4625 12.5 kHz *51 467.8875 12.5 kHz 63 467.4875 12.5 kHz *52 467.9125 12.5 kHz 64 467.5125 12.5 kHz 53 469.4875 12.5 kHz 65 451.1875 12.5 kHz 54 469.5125 12.5 kHz 66 451.2375 12.5 kHz 55 469.5375 12.5 kHz 67 451.2875 12.5 kHz 56 469.5625 12.
BRUS_display.book Page 72 Monday, January 16, 2012 5:28 PM FREQUENCY AND CODE RDX UHF Frequencies (Continued) Bandwidth Frequency # Frequency (MHz) Bandwidth 73 452.5375 12.5 kHz 82 456.4375 12.5 kHz 74 452.4125 12.5 kHz 83 456.5375 12.5 kHz 75 452.5125 12.5 kHz 84 456.6375 12.5 kHz 76 452.7625 12.5 kHz 85 457.3125 12.5 kHz 77 452.8625 12.5 kHz 86 457.4125 12.5 kHz 78 456.1875 12.5 kHz 87 457.5125 12.5 kHz 79 456.2375 12.5 kHz 88 457.7625 12.5 kHz 80 456.
BRUS_display.book Page 73 Monday, January 16, 2012 5:28 PM RDU2080d – UHF DEFAULT FREQUENCIES CHART RDX UHF 8 CH Radios Default Frequencies – RDU2080d Frequency # Frequency (MHz) Code # Code Bandwidth 1 2 464.5500 1 67.0 Hz 12.5 kHz 2 8 467.9250 1 67.0 Hz 12.5 kHz 3 5 467.8500 1 67.0 Hz 12.5 kHz 4 6 467.8750 1 67.0 Hz 12.5 kHz 5 10 461.0625 1 67.0 Hz 12.5 kHz 6 12 461.1125 1 67.0 Hz 12.5 kHz 7 14 461.1625 1 67.0 Hz 12.5 kHz 8 16 461.2125 1 67.0 Hz 12.
BRUS_display.book Page 74 Monday, January 16, 2012 5:28 PM RDU4160d – UHF DEFAULT FREQUENCIES CHART FREQUENCY AND CODE RDX UHF 16 CH Radios Default Frequencies – RDU4160d English 74 Channel Frequency # Frequency (MHz) Code # Code Bandwidth 1 1 464.5000 1 67.0 Hz 12.5 kHz 2 1 464.5000 4 77.0 Hz 12.5 kHz 12.5 kHz 3 1 464.5000 8 88.5 Hz 4 1 464.5000 29 179.9 Hz 12.5 kHz 5 1 464.5000 0 – 12.5 kHz 6 2 464.5500 1 67.0 Hz 12.5 kHz 7 2 464.5500 6 82.5 Hz 12.
BRUS_display.book Page 75 Monday, January 16, 2012 5:28 PM RDX UHF 16 CH Radios Default Frequencies – RDU4160d (Continued) Channel Frequency # Frequency (MHz) Code # Code Bandwidth 11 22 461.3625 3 74.4 Hz 12.5 kHz 30 462.4875 5 79.7 Hz 12.5 kHz 13 32 462.5375 7 85.4 Hz 12.5 kHz 14 34 462.0375 9 91.5 Hz 12.5 kHz 15 36 464.0875 11 97.4 Hz 12.5 kHz 16 38 464.1375 13 103.5 Hz 12.
BRUS_display.book Page 76 Monday, January 16, 2012 5:28 PM CTCSS AND PL/DPL CODES CTCSS Codes Hz CTCSS Hz CTCSS Hz 1 67.0 14 107.2 27 167.9 2 71.9 15 110.9 28 173.8 179.9 FREQUENCY AND CODE CTCSS 3 74.4 16 114.8 29 4 77.0 17 118.8 30 186.2 5 79.7 18 123 31 192.8 6 82.5 19 127.3 32 203.5 7 85.4 20 131.8 33 210.7 8 88.5 21 136.5 34 218.1 9 91.5 22 141.3 35 225.7 10 94.8 23 146.2 36 233.6 11 97.4 24 151.4 37 241.8 12 100.0 25 156.
BRUS_display.
BRUS_display.
BRUS_display.
BRUS_display.
BRUS_display.book Page 81 Monday, January 16, 2012 5:28 PM MOTOROLA LIMITED WARRANTY FOR THE UNITED STATES AND CANADA What Does this Warranty Cover? Products Covered Length of Coverage Products and Accessories as defined above, unless otherwise provided for below. One (1) year from the date of purchase by the first consumer purchaser of the product unless otherwise provided for below. Decorative Accessories and Cases. Decorative covers, bezels, PhoneWrap™ covers and cases.
BRUS_display.book Page 82 Monday, January 16, 2012 5:28 PM WARRANTY Exclusions English Normal Wear and Tear. Periodic maintenance, repair and replacement of parts due to normal wear and tear are excluded from coverage. Batteries. Only batteries whose fully charged capacity falls below 80% of their rated capacity and batteries that leak are covered by this limited warranty. Abuse & Misuse.
BRUS_display.book Page 83 Monday, January 16, 2012 5:28 PM Communication Services. Defects, damages, or the failure of Products, Accessories or Software due to any communication service or signal you may subscribe to or use with the Products Accessories or Software is excluded from coverage. Software. Applies only to physical defects in the media that embodies the copy of the software (e.g. CDROM, or floppy disk).
BRUS_display.book Page 84 Monday, January 16, 2012 5:28 PM Furthermore, the purchase of the Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents, or patent applications of Motorola or any third party software provider, except for the normal, nonexclusive, royalty-free license to use that arises by operation of law in the sale of a product.
BRUS_display.book Page 85 Monday, January 16, 2012 5:28 PM ACCESSORIES Part No. Description RAN4033 UHF Stubby Antenna 450 – 470 MHz RAN4041 VHF Helical Antenna 146 –174 MHz RAN4031 UHF Whip Antenna 438 – 470 MHz AUDIO ACCESSORIES Part No.
BRUS_display.book Page 86 Monday, January 16, 2012 5:28 PM ACCESSORIES CARRY ACCESSORIES Part No. CABLES Description Part No. RLN6302 Hard Leather Carry Case RLN6303 Radio to Radio Cloning Cable RLN6307 Spring Action Belt Clip RKN4155 CPS Programming Cable POWER SUPPLIES AC PIN ADAPTORS Part No. RLN6349 Description North America AC Pin Adaptor CHARGERS Part No. Part No.
BRUS_display.book Page 87 Monday, January 16, 2012 5:28 PM POWER SUPPLIES Description RPN4054 Standard US Fixed Power Supply RPN4058 Standard Exchg AC pin Pwr Supply RLN6170 Rapid Exchg AC pin Pwr Supply Attention: Certain accessories may be or may not be available at the time of purchase. For latest information on accessories, contact your Motorola point of purchase or visit: www.motorolasolutions.
BRUS_display.book Page 88 Monday, January 16, 2012 5:28 PM M RDX Series™ Features Summary Programmable Via RADIO PANEL Programmable via CPS Features Default Value Backlight Display NonDisplay Display NonDisplay No N/A Yes N/A 5 Seconds Programming Tips Choose the backlight’s time out by using the CPS. Front panel programming available only on display Bandwidth Select Yes No Yes Yes Frequency Dependable models by entering Programming Mode (1).
BRUS_display.book Page 89 Monday, January 16, 2012 5:28 PM Programmable Via RADIO PANEL Programmable via CPS Features Default Value Display NonDisplay Display Programming Tips NonDisplay Front panel radio programming available only for Call Tones (4) Yes No Yes Yes OFF / BUTTON A Display Models by going into Programming Mode(1). Values available are 0 (OFF),1, 2 and 3. To enable/disable Call Tones press Button A (default button). Only Display Models.
BRUS_display.book Page 90 Monday, January 16, 2012 5:28 PM Programmable Via RADIO PANEL Features Display NonDisplay Programmable via CPS Display NonDisplay Default Value Programming Tips Enables radio to enter cloning mode in order to clone its profile settings into other radios (using Cloning Mode Yes Yes Yes Yes OFF Radio to Radio Cloning Cable or Multi-Unit Charger). Press PTT, SB2 while turning radio ON. Note: You can clone radios using the CPS.
BRUS_display.book Page 91 Monday, January 16, 2012 5:28 PM Programmable Via RADIO PANEL Programmable via CPS Features Default Value Display Frequencies, Direct Input (3) NonDisplay Display Any value within No No Yes Programming Tips NonDisplay Yes radio frequency Allows you to customize frequencies in your radio. Available only for certain 4W/5W radio models. band Radios Bandwidth is fixed and non-programmable. Bandwidth Range for 2W radios: VHF 150.
BRUS_display.book Page 92 Monday, January 16, 2012 5:28 PM Programmable Via RADIO PANEL Features Programmable via CPS Default Value Display NonDisplay Display NonDisplay IVOX, sensitivity Level Yes N/A Yes N/A Keypad Beep ( or Keypad Tone) (2) Yes Yes Yes Yes ON Keypad Lock (2) Yes N/A Yes N/A UNLOCKED LEDs Enabled/ Disabled No No Yes Yes Enabled Low Battery Alert – Shutdown N/A N/A N/A N/A ON HIGH (Level 3) Programming Tips Available for Display models only.
BRUS_display.book Page 93 Monday, January 16, 2012 5:28 PM Programmable Via RADIO PANEL Programmable via CPS Features Default Value Display NonDisplay Display NonDisplay Microphone Gain Level, ACCESSORY Yes No Yes Yes Microphone Gain Level, RADIO Yes No Yes Yes Programming Tips Medium For front panel programming enter Programming (Level 2) Mode (1). Medium For front panel programming enter Programming (Level 2) Mode (1).
BRUS_display.book Page 94 Monday, January 16, 2012 5:28 PM Programmable Via RADIO PANEL Features Display NonDisplay Programmable via CPS Display NonDisplay Default Value Programming Tips Also known as ‘Squelch defeat’. Short Press SB1 to PL Defeat Yes Yes Yes Yes SB1 Button enable PL/DPL defeat so you can listen or monitor any activity in the channel without noise. Press SB1 again to disable PL/DPL defeat.
BRUS_display.book Page 95 Monday, January 16, 2012 5:28 PM Programmable Via RADIO PANEL Programmable via CPS Features Default Value Display NonDisplay Display NonDisplay No No Yes Yes Programming Tips Reverse Burst eliminates unwanted noise (squelch Reverse Burst 180 tail) during loss of carrier detection. Use CPS to select values 180 or 240.
BRUS_display.book Page 96 Monday, January 16, 2012 5:28 PM Programmable Via RADIO PANEL Features Scan Programmable via CPS Display NonDisplay Display NonDisplay Yes Yes N/A N/A Default Value SB2 Button Programming Tips Short press SB2 to enable/disable scan. Use CPS for editing Scan List (adding/removing Scan List Yes No Yes Yes ON - All channels to be scanned).
BRUS_display.book Page 97 Monday, January 16, 2012 5:28 PM Programmable Via RADIO PANEL Programmable via CPS Features Default Value Display NonDisplay Display Programming Tips NonDisplay Front panel radio programming available in display VOX Sensitivity Level Yes No Yes Yes OFF (level 0) models by pressing PTT or MENU buttons and scrolling down/up with and buttons to set value. Long press PTT to save. Allows to use ‘hands-free’ mode connecting microphone accessories.
BRUS_display.book Page 98 Monday, January 16, 2012 5:28 PM Programmable Buttons Chart Button Monitor Scan / Nuisance Delete Call Tone Power Select Scramble Default SB1 Default SB2 Backlight Channel Preset 1 Channel Preset 2 N/A N/A N/A N/A N/A N/A No Operation Default BUTTON A (*) Default BUTTON B (*) Default BUTTON C (*) Notes: • Buttons come programmed to default functions.
BRUS_display.book Page 99 Monday, January 16, 2012 5:28 PM Icons Chart Icon Symbol Comments Battery Level Displayed during normal radio mode operation, displays battery life remaining. Channel Displayed during normal radio operation and when programming channel features. Code Displayed during normal radio operation and when programming codes features. Frequency Displayed during normal radio operation and when programming frequency features.
BRUS_display.book Page 100 Monday, January 16, 2012 5:28 PM Icon Symbol Comments Power Select Displayed whenever the channel is transmitting or set to a high-power selection. Signal Strength RSSI Display Icon numbers of bars will indicate the strength of the received signal. Repeater(*) Displayed whenever the repeater feature is enabled. Vox/IVox Displayed when IVOX/VOX enabled or when programming MIC / MIC gain features. (*) Available only for 4160d model.
BRUS_display.
BRUS_display.book Page 103 Monday, January 16, 2012 5:28 PM m *NNTN8303A* NNTN8303A MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2007, 2011 Motorola Solutions, Inc. All rights reserved.
