TETRA Mobile Terminal MTM800 380-430 MHz (MT912M) 450-470 MHz (MT512M) MTM700 380-430 MHz (MT912) 806-870 MHz (MT712) Installation Manual art Number: 6866534D67_H @6866534D67@ KT-EMEA / European Publications Department Berlin, Issued: 01.
MTM700/MTM800 Mobile Terminal / Radio Installation Manual COPYRIGHT COPYRIGHT Copyrights © 2001 - 2006 Motorola Inc. All rights reserved. No part of this manual may be reproduced, transmitted, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without the prior written permission of Motorola Inc.
Product Safety and RF Exposure MTM700 Mobile Terminal / Installation Manual v Product Safety and RF Energy Exposure for TETRA Mobile Terminals installed in Vehicles or as Fixed Site Control Stations ! Caution THIS CHAPTER IS AN EXTRACT OF THE MULTI LINGUAL MOBILE SAFETY BOOKLET PUBLICATION No. 6866537D37_. FOR THE LATEST SAFETY INFORMATION REFER TO THE SEPARATE SAFETY BOOKLET DELIVERED WITH YOUR TERMINAL.
vi MTM700 Mobile Terminal / Installation Manual Product Safety and RF Exposure Federal Communications Commission Regulations (US markets only) The FCC rules require manufacturers to comply with the FCC RF energy exposure limits for mobile 2-way terminals before they can be marketed in the U.S. When 2-way terminals are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements.
Product Safety and RF Exposure MTM700 Mobile Terminal / Installation Manual vii Guidelines: • User awareness instructions should accompany device when transferred to other users. • Do not use this device if the operational requirements described herein are not met. Instructions: • Transmit no more that the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button.
viii MTM700 Mobile Terminal / Installation Manual • Product Safety and RF Exposure Use only Motorola-approved supplied antenna or a Motorola approved replacement antenna. Unauthorised antennas, modifications, or attachments could damage the terminal and may result in non-compliance with RF Safety Standards. Approved Accessories • This terminal has been tested and meets the RF Safety Standards when used with the Motorola accessories supplied or designated for this product.
Product Safety and RF Exposure MTM700 Mobile Terminal / Installation Manual ix Facilities To avoid electromagnetic interference and/or compatibility conflicts, turn off your terminal in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy.
x MTM700 Mobile Terminal / Installation Manual ! Product Safety and RF Exposure OPERATIONAL WARNINGS WARNING For Vehicles With Air Bags Do not mount or place a mobile terminal in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a terminal is placed in the air bag deployment area and the air bag inflates, the terminal may be propelled with great force and cause serious injury to occupants of the vehicle.
Product Safety and RF Exposure ! MTM700 Mobile Terminal / Installation Manual ADDITIONAL IMPORTANT INFORMATION FOR SERVICING AND INSTALLING THE TERMINAL Caution Only specialized workshops should be contacted for installation, maintenance and repair work. This unit is equipped with protection fuses in the Power and Ignition Sense Cable. Replace these fuses only with the original ratings! Caution: Failure to use correct manufactures approved parts may result in physical damage to this unit.
xii MTM700 Mobile Terminal / Installation Manual Product Safety and RF Exposure THIS PAGE INTENTIONALLY LEFT BLANK
DOCUMENT HISTORY MTM700/MTM800 Mobile Terminal / Installation Manual 11 DOCUMENT HISTORY The following major changes have been implemented in this manual since the previous edition: Edition Description Date 6866534D67 Initial edition October 2001 6866534D67-A Technical Support addresses for the APAC region added. September 2002 6866534D67-B Active Data Cable GMKN1022 for Packet Data Transmission added to chapter “Installation”. December 2002 Accessories -to- Model Chart updated.
MTM700/MTM800 Mobile Terminal / Installation Manual DOCUMENT HISTORY Edition Description Date 6866534D67-G Pin assingment of GMKN4072 updated (Chapter Installation, page 72). Page 27 - 29: Accessories-to-Model-Chart updated. Aug. 2005 6866534D67-H 45oMHz frequency range added. Visor Mic P/N changed (page 27). 10A Fuse P/N changed (page 28 and 32). Dashboard Installation, Figure 10 and Table 4 updated (page 42 and 43). Table 8 updated (page 57). Term „radio“ replaced by „terminal. Jan.
MTM700/MTM800 Mobile Terminal / Installation Manual 13 CONTENTS COPYRIGHT Copyrights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Computer Software Copyrights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MTM700/MTM800 Mobile Terminal / Installation Manual Parts identification and ordering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Latin America Region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warranty and Repairs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Piece Parts . . . . . . . . . . . . . . . . . . . .
MTM700/MTM800 Mobile Terminal / Installation Manual Expansion Head Radio with Control Terminal & Data Terminal Connectors & Pin Assignment of the Terminal 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Transceiver Rear Side - Pin Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Accessory Connection Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MTM700/MTM800 Mobile Terminal / Installation Manual THIS PAGE INTENTIONALLY LEFT BLANK
SCOPE MTM700/MTM800 Mobile Terminal / Installation Manual 17 SCOPE SCOPE OF THIS MANUAL This manual is intended for use by service technicians familiar with similar types of equipment. It contains informations required for the installation of the equipment described and is current as of the printing date. Changes which occur after printing date may be incorporated by a complete Manual revision or alternatively as additions. NOTE The mobile terminal has to be installed by trained service personnel only.
MTM700/MTM800 Mobile Terminal / Installation Manual SCOPE MTM700 Manuals & User Guides EMEA Installation Instructions 6866534D67 MTM700 Installation Instructions (English) Service Manuals 6866534D19 6866534D20 MTM700 Detailed Service Manual (English) MTM700 Basic Service Manual (English) User Guides (Standard Control Head) 6866537D44 6866537D07 MTM700 Basic User Guide (English/German/French/Dutch/Spanish) MTM700 Feature User Guide (English) only on MOL: (https://emeaonline.motorola.
SCOPE MTM700/MTM800 Mobile Terminal / Installation Manual 19 MTM800 Manuals & User Guides EMEA Installation Instructions 6866534D67 MTM700/MTM800 Installation Manual (English) Service Manual 6866537D20 6866537D72 6866537D98 MTM800 Basic Service Manual (English) MTM800 380-430MHz Detailed Service Manual (English) MTM800 450-470MHz Detailed Service Manual (English) User Guides (Standard Control Head) 6866537D67 6866537D95 6866537D69 MTM800 Basic User Guide (EN / DE / FR / NL / ES) MTM800 Basic User Gu
MTM700/MTM800 Mobile Terminal / Installation Manual 6866537D70 6815603H01 6815602H01 6815601H01 MTM800 Feature User Guide (English) MTM800 Feature User Guide (Trad. Chinese) MTM800 Feature User Guide (Simpl. Chinese) MTM800 Feature User Guide (Korean) Data Terminal User Guides 6815292H01 6815290H01 6815305H01 MTM800 Data Terminal User Guide (English, Trad. Chinese) MTM800 Data Terminal User Guide (English, Simpl.
SCOPE MTM700/MTM800 Mobile Terminal / Installation Manual 21 Warranty and Service Support Motorola offers long term support for its products. This support includes full exchange and/or repair of the product during the warranty period, and service/ repair or spare parts support out of warranty. Prior to shipping any terminal back to the appropriate Motorola warranty depot, please contact Customer Resources or your Motorola dealer, distributor or reseller.
MTM700/MTM800 Mobile Terminal / Installation Manual SCOPE SERVICE INFORMATION Europe, Middle East and Africa Region European Radio Support Centre (ERSC) Motorola European Radio Support Centre is available at: Motorola European Radio Support Centre ERSC Tel.: +49 (0)30 6686 1555 Fax: +49 (0)30 6686 1579 Am Borsigturm 130 13507 Berlin Germany EMEA Systems Support Centre (ESSC) The Systems Support Centre is available at: Telephone: +44 (0) 1256 484448 E-mail: ESSC@motorola.
SCOPE MTM700/MTM800 Mobile Terminal / Installation Manual 23 Asia, Pacific Region Piece Parts Some replacement parts, spare parts, and/or product information can be ordered directly. If a complete Motorola part number is assigned to the part, it is available from Motorola Radio Aftermarket and Accessory Division (AAD). If no part number is assigned, the part is not normally available from Motorola.
MTM700/MTM800 Mobile Terminal / Installation Manual Latin America Region Latin America Radio Support Centres The Customer Support is available through the following service centres: Warranty and Repairs: MOTOROLA DE COLOMBIA SERVICE CENTRE Carrera 7 No. 71-52 Torre B piso 13 Oficina 1301 Bogota- Colombia (571) 376-6990 MOTOROLA DE MEXICO SERVICE CENTRE Bosques de Alisos #125 Col.
MODEL INFORMATION & ACCESSORIES 25 MTM700/MTM800 Mobile Terminal / Installation Manual MODEL INFORMATION & ACCESSORIES MTM700/MTM800 Mobile Terminal Model Information This manual applies to the following Mobile Terminal Models Type No. Sales Model No.
MTM700/MTM800 Mobile Terminal / Installation Manual MODEL INFORMATION & ACCESSORIES Model Specifications* GENERAL ETSi: RECEIVER ETS 300 394-1 Type Number: MTM700/MTM800 UHF MTM700 806-870 MHz MTM800 450-470 MHz Receiver Type: TRANSMITTER Superheterodyne Frequency Range: MT912/MT912M MT712 MT512M Temperature Range for Transceiver: Operating Storage: -30°C to +60°C -40°C to +85°C Power Supply: Minimum: Nominal: Maximum: max.
MODEL INFORMATION & ACCESSORIES 27 MTM700/MTM800 Mobile Terminal / Installation Manual Accessories-To-Model Chart ACCESSORIES Control Heads Part Number M1 M2 Standard Control Head GMWN4062_ X X Standard Control Head, cyrillic keypad GMWN4310_ X X Standard Control Head, Chinese (MTM700 with MR3.2b software only) GMWN4187_ X X Motorcycle Control Head SDLN4506_ X Motorcycle Control Head, Chinese (MTM700 with MR3.
MTM700/MTM800 Mobile Terminal / Installation Manual MODEL INFORMATION & ACCESSORIES ACCESSORIES Desktop tray without loudspeaker GLN7318_ X X X Power cable (for supply to desktop mobile) GKN6266_ X X X M1 M2 M3 M4 X Remote Mount Part Number Back Housing for Remote Mount GMCN4060_ X Remote mount cable (terminal to C/H) - 3m RKN4077_ X X Remote mount cable (terminal to C/H) - 5m RKN4078_ X X Remote mount cable (terminal to C/H) - 7m RKN4079_ X X Junction box GMLN3002_ X
MODEL INFORMATION & ACCESSORIES 29 MTM700/MTM800 Mobile Terminal / Installation Manual ACCESSORIES Low Profile Mounting Bracket GLN7324_ X X X DIN Mount Kit for Terminal Chassis RLN4781_ X X X M1 M2 M3 Motorcycle Cables Part Number X M4 Cable, M/C CH to Expansion Head Radio 3066516B01 X Cable Kit, Transceiver to Microphone GMKN4072_ X Remote mount cable (terminal to C/H) - 3m RKN4077_ Cable, M/C CH to Exp.
MTM700/MTM800 Mobile Terminal / Installation Manual MODEL INFORMATION & ACCESSORIES 1) Compatibility of Active Data Cable GMKN1022 Category Terminal Model: UHF MT912 MT912M Terminal Model: 450MHz MT512M Terminal Model: 800MHz MT712 Kit Model / Part No. Compatible Yes / No Description M47PCN6TZ5AN M80PCN6TZ5AN MTM700 380-430 Dash/Desk MTM800 380-430 Dash/Desk Yes with Rev. B Tanapas only Yes M47PCN6TZ6AN M80PCN6TZ6AN MTM700 380-430 Remote MTM800 380-430 Remote Yes 2 with Rev.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 31 INSTALLATION Introduction General Information NOTE This product must be installed in a vehicle in accordance with the vehicle manufacturer’s guidelines and the instruction detailed in this manual. Only the specified Motorola parts in this manual should be used. Failure to do so could result in non compliance to the Automotive Directive (72/245/EEC, as amended by 95/54/EC).
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION DC Power Cable Installation Installation Planning ! Caution CAUTION: This terminal must be operated only in negative ground electrical systems. Operating the terminal on a positive ground system will cause the cable fuse to short-circuit. Check the vehicle ground polarity before you begin the installation. The 3 meters (10 feet) DC power cable shipped with the terminal should be long enough to be installed in most vehicles.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 33 Installation Procedure Begin the DC power cable installation as follows: 1. ! Caution 2. ! Determine a routing plan, keeping in mind where the terminal is to be mounted and make sure that the cable does not rest on sharp edges. CAUTION: Improper handling with the power cable may cause shorting to ground. Ensure that during terminal installation the power cable fuse is removed.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Fuse (10A) Fuse Holder Adapter Cover Red Lead Red Lead (min. 2.5 mm2) Red Lead (min. 2.5 mm2) Mounting Hole Ring Lugs Black Lead (min. 2.5 mm2) To Battery or Chassis To Battery + Figure 2 Power Cable Assembly 5. Place the fuse holder close to the battery. Ensure that it is not near any hot engine component. Mount the fuse holder using its mounting hole and dress the wires as required. 6.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 35 Ignition Sense Cable Installation Table 2 Ignition Sense Cable Number Description Rating HKN9327 Ignition Sense Cable with fuse 4A Ignition Sense Cable, Length: 3 m 6580283E02 Fuse 4A for Ignition Sense Cable The HKN9327 Ignition Sense Cable allows the terminal to be turned on and off by the vehicle ignition switch. The ignition sense cable kit contains a thin cable and a fuse holder.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Terminal Installation Standard Control Head Installation The Standard Control Head can be removed from the housing and turned to any position within a 180° radius. This provides multiple mounting options for the terminal. For example, the terminal may be mounted on either side of the vehicle to facilitate the safest and most ergonomically ideal position. The Standard Control Head may then be turned to provide the most convenient access.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 37 Trunnion Installation Installation Planning The trunnion allows the terminal to be mounted to a variety of surfaces. 1. The trunnion must be securely fixed to the vehicle chassis. 2. Ensure the surface can support the weight of the terminal. 3. Although the trunnion can be mounted to a plastic dashboard, it is recommended that the mounting screws be located so they penetrate the supporting metal frame of the dashboard.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Installation Procedure 1. Select either the transmission hump or an open underneath portion of the dash to mount your terminal. (See Figure 7 Transmission Hump Mounting (Top) and Below Dash Mounting (Bottom)). When mounting the trunnion on the transmission hump, be careful that the transmission housing is not affected. 2. Use the trunnion mounting bracket as a template, to mark the hole positions on the mounting surface.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 39 TRANSMISSION HUMP MOUNTING Mode Menu Wing Screw (2) Tab Tab Mounting Surface Trunnion Mounting Bracket Tab 28mm (1.12") 46mm (1.84") 73mm (2.92") 46mm (1.84") 73mm (2.92") BELOW DASH MOUNTING Mounting Surface Wing Screw (2) Sheet Metal Screws 2 abc 1 3 def 4 ghi 5 jkl 6 mno 7 pqrs 8 tuv 9 wxyz MODE Note: The keypad labeling of the control head may vary according to the specific customer/country concerns.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Desktop Installation The MTM700/MTM800 may be desktop mounted. The Desktop Station option provides the terminal with the desk microphone, power supply, desk top tray (without speaker) and external loudspeaker. A separate data device can be connected via the 7-pin Expansion connector on the rear side (located above the 20-pin accessory connector as shown in figure 8).
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual Walloutlet Line Cord with Ground Power Supply Laptop RS232 Interface Cable Speaker Lightning Protector with Quarter-Wave Shorting Stub Outdoor Antenna 12V Desktop Power Cable or CCCCCCCCCCCC C CC C CCC Desk Microphone 41 Antenna Cable BNC Antenna Connector C CCCC C CCC C CCC CCC CCC C Indoor Antenna CC CCCCC Radio in Base Tray Figure 9 Desktop Mounting with Data Device Table 3 Associated Components Item Description Par
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Dashboard Installation TERMINAL SPECIFIC NOTE Installation in the dashboard is only possible when the Transceiver Box is assembled with a Remote Mount Head or a Expansion Head. Dashboard Installation of the Transceiver Box equipped with a Standard Control Head is NOT possible ! Installing the Radio in an Automotive Dashboard 1. Open out the radio cut-out in the dashboard. 2. Remove the top plastic cover off the radio. 3.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 43 Mounting the Radio in the Frame 1. Provide the electrical connections to the radio for power, antenna and accessories. 2. Plug in all the connectors and push the radio with its Remote Mount Head or alternatively the Expansion Head firmly into the mounting frame until the two springs snap into place. RADIO SPECIFIC NOTE The fixing tabs should be checked for tightness each time the radio is removed.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Remote Mount Installation 10-pin Connector Remote Mount Cable Trunnion Transceiver Flex Flex PCB 0 Back Housing for Remote Mount 0 Back Housing for Remote Mount Kit 10-pin Connector Remote Mount Head Kit Standard Control Head or Remote Mount Head or Data Expansion Control Head Kit Data Expansion Control Head Figure 11 Remote Mount Installation with Remote Mount Head Table 5: Associated Components Remote Mount Kit Descript
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 45 Table 6: Associated Components Remote Mount Expansion Kit Description Part Number Remote Mount Expansion Kit, 3 m Data Expansion Control Head Kit GMCE4053_ Back Housing for Remote Mount Kit GMCN4060_ Remote Mount Cable, 3 m RKN4077_ Speaker Extension Cable GMKN4084_ Remote Mount Expansion Kit, 5 m Caution PMLN4496_ Data Expansion Control Head Kit GMCE4053_ Back Housing for Remote Mount Kit GMCN4060_ Remote Mount Cable, 5
MTM700/MTM800 Mobile Terminal / Installation Manual 5. INSTALLATION Connect the flex from the Standard Control Head to Remote Back Housing PCB. O NOTE For correct orientation of the flex align the “dot” on the flex with the ‘O’ on the PCB. Marking on PCB Marking on Flex Figure 13 Orientation of Flex to PCB 6. Press the Standard Control Head onto the Remote Back Housing until ALL the tabs snap into place. Assembling the Remote Front Housing to Transceiver Box 1.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 47 Remote Mount Installation (Remote Mount with Junction Box) Speaker to MTM700/MTM800 accessory connector External PTT To Ignition switch Visor microphone GMMN1033_ F2 4A Connecting cable GMKN4192/3/4 External alarm Emergency switch Fist Microphone GMMN4063_ or Telephone style handset GMUN1006_ Junction Box GMNL3002_ Accessory Connector Kit GMBN1021_ Programming Cable FLN9636_ CPS Standard RS232 cable Laptop Laptop Figure 14
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Connections 1. Connect all accessories to the junction box. 2. Connect the mobile-terminal-to-Junction box cable to the junction box. 3. Connect the programming cable to the junction box (if required). 1 = Connecting cable from Junction Box to MTM700/MTM800 (rear side accessory connector) for installation purpose only.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 49 Connection Plan for Junction Box Accessory Terminal Connection Plan for Speaker 1 2 External Speaker 1 2 3 4 5 6 SPEAKER 7 JUNCTION BOX TERMINAL Connection Plan for Alarm Relay BUZZER BLK 5 RED +12V ALTERNATIVE 1 2 3 4 External alarm 5 6 5 BLK RED 86 87 85 30 7 +12 V JUNCTION BOX TERMINAL ALTERNATIVE 5 +12 V RED ALARM RELAY RED BLK +12 V +12 V BLK 86 87 85 30 ALARM RELAY RED +12 V BLK Connect
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Connection Plan for Ignition Sense Cable TO IGNITION SWITCH 4A 1 2 3 4 5 IGNITION SENSE CABLE SWITCHED BATTERY VOLTAGE 6 7 JUNCTION BOX TERMINAL The ignition sense cable HKN9327 allows the MTM700/MTM800 to be turned on and off by the vehicle ignition switch. To install the cable, carry out the following steps. 1. Connect the stripped lead of the fuse holder cable only to an ignition switched terminal of the fuse block.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 51 Connection Plan for Accessory Connector Kit (GMBN1021) Part Number / Description Cable Connectivity GMSN4066 Speaker 13W GMSN4078 Speaker 5W SPKR- 1 SPKR+ 16 GMMN4065 Visor Microphone GMMN1033 Visor Microphone, omni directional Can NOT be used if connector 7 (TELCO) is in use! RLN4856 RLN4857 RLN4858 MIC 2 GND 7 Foot switch PTT Push button PTT Gooseneck PTT PTT 3/ Emergency 9 GND 8 These accessories could be used for PTT or Emerg
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Expansion Head Radio Installation General The Expansion Head Radio is a kit consisting of the MTM700/MTM800 transceiver-box and an Expansion Head, which fits onto the front of the MTM700/MTM800 mobile terminal transceiver. The Expansion Head Radio is used e.g.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 53 7. Ensure that the control head and the control head trunnion are grounded. 8. Verify that there is sufficient space around the units to allow air flow and removal. 9. Verify that the cable from a handlebars mounted control head and to the radio unit is long enough to allow for the handles to be turned. 10. Verify that the antenna cable is routed in the shortest way to minimize power loss over the cable. 11.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Configuration with SB 9600 Interface non-Motorola Accessories: to e.g. Helmet with Microphone and Earpiece, external PTT, etc.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 55 Configuration with Y-Adapter (Chinese version, MTM700 only) non-Motorola Accessories: to e.g. Helmet with Microphone and Earpiece, external PTT, etc.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Motorcycle Control Head Note: The keypad labeling of the control head may vary according to the specific customer/country concerns. Figure 20 Motorcycle Control Head - front side (abowe: Standard EMEA CHD / below: Chinese CHD) Motorcycle Control Head Installation 1. Install the bushings into the trunnion (see Figure 21 Motorcycle Control Head mounted in a trunnion). 2.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 57 Mechanical Parts Table 8 Motorcycle Control Head - Mechanical Parts List for Installation Item Motorola Part No. Description 1 0305760W02 Wing Screw(2x) 2 4380128N01 Bushing (2x) between trunnion and control head 3 0780127N02 Trunnion (Metal) 4 3202113U01 Gasket inside the connector 5 SDLN4486 Connector Bracket Kit Installation of Connecting Cable (3066516B01) 1.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Expansion Head Radio with Standard Control Head & Data Terminal This configuration allows controlling the radio (Transceiver Box) by the Standard Control Head. In addition sending / receiving of packet data or short packet data by using a Data Terminal which is connected to the 9 pin subD connector (8-wires RS232 interface) is possible. The connecting cable is a standardized RS232 cable and is available in PC shops.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 59 Expansion Head Radio with Control Terminal & Data Terminal This configuration allows controlling the radio (Transceiver Box) with a Control Terminal (e.g. Personal Computer, Laptop, Console etc.). In this configuration the Control Terminal is a substitute for the Standard Control Head.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Connectors & Pin Assignment of the Radio Transceiver Rear Side - Pin Function 7 pin RS232 connector (MTM700 only) 20 2 4 19 1 3 6 8 10 12 14 16 18 5 7 9 11 13 15 17 Accessor y Connector *Note the location of Pin 1 Figure 25 Location of Accessory Connector and Expansion Connector - Rear Side This section gives a description of the Accessory Connector and Expansion Connector pin functions.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 61 Table 9 20-Pin Accessory Connector Pin Function Description 10 IGNITION Connecting this pin to the ignition line of the vehicle that will automatically turn on the radio if ignition of the vehicle is turned on. High active. 11 RX_AUDIO This is the received RX signal. Output impedance approximate 600 Ohms; unsymmetrical; output level = 775mVRMS 12 AUDIO_PA_ENABLE This is a digital input.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Accessory Connection Plan ! Caution CAUTION: The accessory connections shown are not compatible to some other models of Motorola radios. Check the appropriate accessory or technical manual for further information. Ensure correct position of the accessory connector.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 63 Connectors & Pin Assignment of Expansion Head and Remote Mount Head Front View Caution: NO Microphone Connector 9 8 7 6 5 4 3 2 1 10 1 13 25 10-Pin TELCO Connector 14 25-Pin subD Connector 1 5 9 6 9-Pin subD Connector Figure 26 Expansion Head - Front View and Connector Location Front View Caution: NO Microphone Connector 10-pin Telco Connector 10 1 2 3 4 5 6 7 8 9 Figure 27 Remote Mount Head - Front view and Connector loca
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Table 11 10-Pin TELCO Connector Pin Function Description 1 FLT_A+ This voltage is at battery voltage level and is available as long as the radio is connected to the supply voltage. The maximum current is 300 mA. A fuse in the radio prevents further circuit damage in case of shorting this pin to ground. 2 5V Supply Voltage This voltage (5 volts) is available when the radio is switched on. The maximum output current is 100mA.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 65 25-Pin subD Connector Connection of Data Devices: This connector offers a connectivity between a Data Device with RS232 interface and the Expansion Head Radio with its SB9600 interface. This interface is a special Motorola Serial Interface. For further information of the SB9600 Interface Cable please refer to section „Connecting Cables“.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Table 12 25-Pin subD Connector Pin Function Description 21 Motorcycle ON/OFF On / Off control for Motorcycle Control Head 22 EXPANSIONPTT When this input is used to key up the transmitter, the internal Mic Audio input (pin 16) is selected. 23 SB9600_SW This input is intended to switch the 4 wire RS232 interface into SB9600 mode. The radio must be switched off and then this input must be connected to pin 6 (FLT A+).
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual Connector & Pin Assignment of the Standard Control Head Flex Cable Pin 1 o Front View to Microphone Connector 9 8 7 6 5 4 3 2 1 10 Mode Menu Note: The keypad labeling of the control head may vary according to the specific customer/country concerns.
PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 18 NC KEYLOAD RESET BUS NC NC GND RX_AUDIO MC ON_OFF NC KEYFAIL NC GND BUSY BUS + NC A+ SW_B+ 9 10 BOTTOM VIEW FEMALE CONNECTOR Motorcycle Control Head ALUMINIUM SHIELDED TWISTED PAIR 250 cm ± 10 cm 14 PIN1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 GND NC NC NC NC A+ NC BUSY RX_AUDIO KEYLOAD KEYFAIL SW_B + BUS NC BUS + NC RESET NC GND NC MC ON_OFFNC NC to PIN 6 NC NC 25 25-PIN D-TYPE CONNECTOR 13 MALE Expansion Head Radi
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 69 Motorcycle Control Head-to-Expansion Head via Y-Adapter (Chinese version) Part Number: 3066516B02 Length: 2.5 m (8.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Radio-to-Junction Box Part Number: 3066537B01 Length: 6 m (19.69 feet) JUNCTION BOX CONNECTOR 26-pin DSub MTM700 ACCESSORY CONNECTOR 20-pin AMP Pin from (signal name) wire gage wire colour Pin TWISTED PAIR to (signal name) TWIST / 25.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 71 Expansion Head Radio-to-Data Device This is a standardized RS232 cable (will not be provided by Motorola). Use the 9-pin socket on the front side of the Expansion Head Radio to connect this cable with the data device. Figure 32 Standardized RS232 Cable NOTE The Expansion Head has a protection grade of IP54.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Part Number: GMKN4072 Length: 65 cm (2.2 feet) 1 2 5 4 3 6 7 8 9 1 1 1 3 1 5 1 0 1 2 1 4 1 6 8 7 6 5 4 3 2 1 6 5 c m (2 .
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 73 Table 16 Colour Assignment of the Cable from Expansion Head -to- Helmet, external PTT, etc. Pin Colour Function Description 4 BROWN Ground Ground 5 GREY Speaker - Negative output of the radio's audio PA. Speaker + and Speaker - are used to connect a control head speaker or monitor speaker. 1) 6 BLACK Internal Mic Audio This input connects to the microphone connector on the control head and depends on radio programming.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Radio-to-Data Device: RS232 Interface Cable (MTM700 only) The GMKN1016_ RS232 Interface Cable allows to connect Data Devices to the radio. This means this cable has to be used for when data transmission between the Radio and a Data Device is required. This cable is mostly used when the transceiver is equipped with a Remote Mount Head or the Standard Control Head is mounted directly. (Expansion Head Radio has a frontside connector).
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 75 Radio-to-Data Device: Active Data Cable The GMKN1022_ Active Data Cable provides a 5-wire RS232 interface (e.g. RxD, TxD, CTS, RTS, DTR) between a computer and a mobile radio. The cable has to be connected to the 20-pin Accessory Connector on the rear side of the radio and into the 9-pin connector of a Data Device (e.g. PC, Laptop, console etc.) The GMKN1022_ Active Data Cable is not repairable. Order a replacement cable as necessary.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Interface Cable SB9600-to-RS232 The GMKN4079 SB9600 Interface Cable provides a connectivity between a computer’s RS232 port and the Expansion Head Radio’s SB9600 interface. If the SB9600 Interface Cable is connected to the Expansion Head Radio then the Radio is switched into the SB9600 mode (Motorola Serial Interface) by a Data Device. this unit e.g. PC, laptop, console etc. controls the radio instead of a Motorcycle Control Head.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual 77 Vehicle Antenna Installation Mobile Radio Operation and EME Exposure To assure optimal radio performance and that human exposure to radio frequency electromagnetic energy is within the guidelines referenced in this document, transmit only when people inside and outside the vehicle are at least the minimum distance away from a properly installed, externallymounted antenna.
MTM700/MTM800 Mobile Terminal / Installation Manual INSTALLATION Antenna Installation Procedure 1. Mount the antenna according to the instructions provided with the antenna kit. Run the coaxial cable to the radio mounting location. If necessary, cut off the excess cable and install the cable connector. 2. Connect the antenna cable connector to the radio antenna connector on the rear of the radio. 3.
INSTALLATION MTM700/MTM800 Mobile Terminal / Installation Manual External Speaker Installation 1. Remove the speaker from the trunnion bracket by loosening the two wing screws. 2. Choose a place to mount the speaker. When mounting the trunnion on the transmission hump, be careful that the transmission housing is not affected. 3. Use the trunnion bracket as a template to mark the positions of the mounting holes. 4.
MTM700/MTM800 Mobile Terminal / Installation Manual THIS PAGE INTENTIONALLY LEFT BLANK
PRODUCT SPECIFIC INFORMATION MTM700/MTM800 Mobile Terminal / Installation Manual Appendix - 81 APPENDIX Product Specific Information for Digital Terminals Type MT912/MT712 and MT912M This section gives the Service Personnel an overview about product specific notes. This is necessary to take special precautions to avoid the introduction of hazards when operating, installing, servicing or storing equipment. This terminal meets the applicable safety standards if it is used as described.
Appendix - 82 MTM700/MTM800 Mobile Terminal / Installation Manual PRODUCT SPECIFIC INFORMATION Spezielle Produktinformationen für Funkgeräte des Typs MT912/MT712 und MT912M Dieses Kapitel gibt dem geschulten Servicepersonal einen Überblick über wichtige produktspezifische Informationen. Diese Informationen sind wichtig, um Risiken beim Bedienen, Installieren und Service zu vermeiden.
